Search Documents

By J. A. Organiscak

Data on dust-control practices, mining conditions and occupational exposures were gathered for approximately 80 underground continuous mining units. Despite silica contents on dust samples in excess of 5%, nearly forty units successfully maintained silica concentrations at or below 100 µg/m3 on a majority of occupational dust samples, while the remainder had difficulty maintaining this level. These two sample sets were termed Group A operations and Group B operations, respectively. This data was compared to identify causes of high occupational silica dust exposures. Analyses of dust-control parameters and geologies revealed only minor differences between these two groups. However, subsequent comparisons of face ventilation design showed considerable differences in silica exposure and silica content between Group A and Group B at the continuous mining machine and roof bolter operator occupations. These differences were minimal when using exhaust curtain ventilation with a dust scrubber. This face ventilation system can benefit operations having difficulty controlling silica dust exposure and silica dust content. The collected data also showed that occupational samples from Group B operations possessed generally higher silica exposures and silica content than similar samples from Group A. The single head roof bolter (helper) possessed among the highest silica exposures and silica contents in both groups.

Jan 1, 2002

By Angelus S. C. Owili-Eger

The past decade has witnessed an unprecendented proliferation of groundwater computer models. Some of these numerical models were developed for the purpose of simulating groundwater movement in mining environments and predicting inflow rates into active mines. However, a general acceptance of these models as routine planning tools by the mining industry has been slow. Until recently, the major use of these models in the industry is by consultants. There are several reasons that have contributed to this situation. Some of these factors - include scarcity or non-existence of an appropriate data base information required for executing these models, the difficulty and costs involved in acquiring data, and the fact that the instructions for using these models are often too involved and time consuming. Today, however, the state-of-the-art technology has been advanced to a level where numerical models can be routinely used to simulate and predict inflow rates into active mining environments. Such environments include highly fractured (longwall) and deforming flow media. Features integrated into these comprehensive and yet easy to use models are double-porosity-pressure, multiphase, and non-darcian flow conditions. This paper reviews the role that computer modeling has played in mining-related operations by presenting several case studies and the state-of-the-art tools currently in use. Included will be some of the practical field applications that have been compiled during the past decade.

Jan 1, 1986

By Jim M. Johnson

INTRODUCTION The facility water balance and maintenance of sufficient excess storage volume in the solution control system are often amongst the most critical facets of design and operation of heap leach facilities in cold, snowy climates. The purpose of this paper is to summarize and discuss climatic and operational factors which have a significant impact on heap leach water balance evaluations in high snowfall climates. Example water balance simulations are presented for proposed heap leach projects located in areas subject to high snowfall in the northwestern United States. The climatic data input to these simulations represent both net evaporative and net precipitation climates. FACTORS AFFECTING WATER BALANCE EVALUATIONS The combined effects of seasonal operations, re1atively low evaporative losses, and potentially large inflows to the solution control system from snowpack and spring storms require an enhanced awareness of the factors which impact facility water balance. Unlike operations at mines in more arid climates, seasonal excess water rather than a shortage of make-up water is the rule. A thorough understanding of a number of factors, including regulatory constraints, climatic influences, and impact of operating philosophy and techniques, is critical to successful development of an incident-free heap leach operation under high snowfall climatic conditions. A process water circuit schematic for a typical heap leach operation is shown on Figure 1.

Jan 1, 1988

The US Geological Survey (USGS) held a one-day workshop at its Denver, CO facility to inform the public of the status of its National Mapping Program. In addition, the agency wanted to obtain information from topographic map users on what their needs are. The agency wants to know what the topographic map user wants. The USGS faces the challenge of keeping up with the changing needs of the nation. In the last few years, the agency has changed dramatically to meet these needs. For example, the "new" USGS incorporates mineral-information specialists from the former US Bureau of Mines and also uses the expertise of former National Biological Service employees. These areas complement the agency's traditional strengths in mapping, geology and water re- sources. The stated mission of the USGS's National Mapping Division is to "meet the nation's need for basic geospatial data, ensuring access to and advancing the application of these data and other related ears science information f& users worldwide." To accomplish this goal, the USGS publishes topographic maps, including shaded-relief editions of areas of special interest (state maps and national parks); photo image maps; satellite image maps; geologic maps and hydrologic maps. The geologic maps include geologic quadrangle maps, oil and gas investigation maps and charts, and coal investigations maps. The familiar 7.5-minute series topographic maps are the most widely used. The 7.5-minute- (1:24,000-scale-) format mapping was begun in 1935.

Jan 1, 1998

By Stephen W. Lambert

One of the primary interests of the United States Department of Energy's Mine Planning Division is to fully develop avenues of technical research which potentially offer positive effects on coal mine productivity. One such area of research involves the removal of methane gas from unmined portions of coalbeds through vertical wells drilled from surface locations. As coalbed methane content is reduced, less gas is available for flow into the mine, and consequently ventilation requirements are decreased and/or coal extraction rates increase. Another attractive aspect of the vertical borehole drainage method is that it presents an opportunity to recover and utilize significant quantities of methane gas, which would otherwise be wasted to the atmosphere. The viability of removing gas from the Mary Lee coalbed using stimulated vertical boreholes was first suggested by Elder and Deul as a result of a United States Bureau of Mines' drilling project conducted from 1971 to 1974 (4). Other United States Bureau of Mines' studies forecasted that degasification would eventually be necessary in the Mary Lee coalbed because most new or expanding mine development would take place at depths exceeding 1 000 feet (305 meters), where the methane problem would be severe (3) (13). In 1975 a large-scaled drilling program was designed in order to supply industry's anticipated need for a degasification technology in the Warrior coal basin, Alabama. The results of this government/industry sponsored effort were to be specifically applicable to the Mary Lee coalbed, the most extensive and economically important deep minable coal present in the area. Major technical objectives of this program are twofold: (1) to measure the effects of various well completion designs, particularly hydraulic stimulation, on mining and (2) to determine the effects of well spacing on gas drainage rates. A cooperative agreement was established with United States Steel Corporation in late 1975 and field work began shortly thereafter in the proximity of a newly developing mine near Oak Grove, Alabama. Government responsibility for this program was transferred from the United States Bureau of Mines to the United States Department of Energy in October 1977. To date, as a result of this program, twenty-one wells have been completed into the Mary Lee coalbed at the Oak Grove site. Seventeen of these wells were drilled on an experimental grid pattern located two miles from the active mine. These grid wells are primarily being used to generate data necessary to determine the effects of well spacing on gas drainage rates and will also provide a large amount of information regarding the long-term effects of degasification on mining. The four remaining wells (designated Ton through TW4) were placed near the mine so that the full effects of completion could be studied within the short time required for underground interception. Results gathered from the first two test wells (TW1 and TW2) have been reported in detail (10) and indicated that several improvements were necessary to increase gas drainage rates. Hydraulic stimulation was one of the most important aspects of well design that required improvement. Nitrogen-charged foam stimulation treatment was used at TW3 and TW4 instead of the gelled-fluid type stimulation used at the first two near-mine test wells.

Jan 1, 1980

By Edward C. Dowling

The advance of science and technology influences the modern economy in countless ways. Older industries must adapt to changes in the marketplace, while new industries are born by applying new technology to meet consumer needs. In light of declining head grades and increased unit costs in the US minerals industry, new technological developments in the production environment are paramount to maintaining a competitive footing in the international marketplace. Micro-engineering research provides the transition between the knowledge base and the application of new technology on the production level. Economic considerations The primary goal of technical development in the production environment is to reduce unit operating costs. Simply stated, this is accomplished by improving operating efficiencies and productivities on the production level. The goal of micro-engineering research in the production environment is to evaluate promising technologies and develop the criteria necessary to apply them in operations. As such, this process is the first step toward innovation and discovery. Generally, the micro-engineering research is followed by macro-engineering development. In the production environment, there are generally more development projects than can be accomplished in a timely manner. Usually, this is the result of financial and human resource limitations. Consequently, it is necessary to prioritize the work such that the most beneficial projects are accomplished first. By performing a discounted cash flow analysis and using benefit-cost ratios (for non-mutually exclusive alter¬natives) or net present value criteria (for mutually exclusive alternatives), the projects can be rated from best to worst. In this way, the financial and human resources can be best allocated to first complete those projects giving the highest returns before moving on to other activities. Moreover, this information is a prerequisite for management to justify additional financial or human resources.

Jan 1, 1992

By Shallesh K. Patel, Richard M. Powers, Patrick Zhang

Perceived environmental impacts from flotation reagents used in the phosphate industry have been of concern for nearly a decade. A research program was initiated to determine the distribution, fate, and consequences of flotation reagents (fatty acids, fuel oils, and amines) within the environment. Therefore, laboratory investigations of biodegradation and soil attenuation of the reagents were conducted along with field flotation mass balances and groundwater investigations in clay settling, sand tailings, and undisturbed areas. Sample analysis and a reagent mass-balance model indicated that most reagents are distributed in clay settling and sand tailings areas. Groundwater analyses showed no fatty acids or amines in any of 19 surficial or intermediate aquifer water samples. In contrast, fuel oils were detected in the surficial aquifer at all sand tailings areas in concentrations ranging between 8.5 and 0.5 mg/L. Fuel oil was also detected in trace amounts (0.6 mg/L) in one intermediate aquifer well located in an active sand tailings area. All fuel oil concentrations detected were very low and, coupled with a biodegradation rate of approximately 10% per month, all concentrations should be within reference levels in six months. Based upon the results of this study, use of flotation reagents in the beneficiation process of the Florida phosphate industry present no long-term threat to the environment.

Jan 1, 1999

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991

By Paul Clifford

The Florida Institute of Phosphate Research (FIPR) is an independent, state of Florida research agency. It was created in 1978 to conduct research to enhance the competitiveness of the Florida phosphate industry. The institute also conducts research to prevent, minimize or rectify environmental impacts caused by the industry. And it helps educate the public concerning phosphate-related technology and issues. FIPR is funded by a severance tax on the industry and is governed by a five-member board of directors appointed by the governor. FIPR&apos;s research is playing a role in enhancing the competitiveness of the Florida phosphate industry. Its technology research program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. It is developing new and improved methods of beneficiation and fertilizer production. This includes new process flowsheets and on-line analyzers and process control methods. FIPR is also developing uses for the phosphogypsum byproduct of phosphoric acid production and evaluating the risks associated with its uses.

Jan 1, 1998

By M. J. Richards, T. X. Ren

Determination of the state of an underground fire plays an important role in fire fighting, rescue and reopening operations. This is normally achieved by the analysis and interpretation of fire gases taken from the fire zone. However, drawing conclusions from gas analysis is not an easy task and needs specialist skills, expertise and experience that are usually beyond the knowledge of the officials in a mine. The complexities of a mine fire and the uncertainties of available information often make effective fire fighting decisions difficult if not impossible. This paper describes a knowledge based expert system that can aid in the diagnosis of sealed coal mine fires. Using a commercially available shell, the expert system has been designed to accommodate a series of diagnostic rules replicating the reasoning logic that would be used by human experts. The system allows the diagnosis of explosibility of the fire zone and trends of various fire ratios to be easily visualised for decision making. By continuously analysing the incoming information, the system is able to provide a rapid assessment of the situation of a sealed mine fire prevailing under specific mining and geological conditions. In addition, short term trends in fire behaviour can be predicted and possible fire control actions recommended. An example is given and shows how this system can be used as an analytical tool in various ways to assist the combating of coal mine fires. Further development of the system is discussed.

Jan 1, 1993

By Haydn H. Murray

A hydrothermal bentonite located in the high Sierras in Nevada is being mined and processed to produce a natural dietary supplement. The minerals present are smectite, gypsum, jarosite, quartz, feldspar, kaolinite, goethite, hematite and zeolite. The clay material was analyzed for respirable crystalline silica, asbestiform minerals, heavy metals and dioxin. No asbestiform minerals are present and the crystalline silica, heavy metals and dioxin are all less than the maximums set by Federal and State agencies. The clay material was analyzed chemically for all major, minor, trace and rare earth elements. The geology, applications and analyses will be discussed in the paper.

Jan 1, 2005

By Greg R. Wheeler

Few members of the general public have a clear understanding of mineral resources. Most people do not know how minerals are mined or why they must be extracted from many diverse locations. Many people acquire knowledge of mineral development from mass media sources with incomplete details or obvious anti-mining bias. The California Mineral Education Foundation was formed in 1991 to provide educational opportunities for the public and industry. There have been major changes in earth science teaching requirements for kindergarten through 12th grade (K-12) curricula since the passage of California Senate Bill 813 in 1983. Model graduation standards, curriculum standards and the state science framework mandate substantial coverage of geoscience topics. The California State Commission on Teacher Credentialing has completed changes in multiple subject and single subject science credentials which will require more geoscience preparation for all teachers. The need for pre-service and in-service education in geoscience is at an all time high. Teachers must have continuing education to maintain their credentials and many are now seeking information in geoscience. The California Mineral Education Foundation designed and conducted the California Mineral Education Conferences held in August 1991 and 1992. The conferences involved lectures and field trips on mining geology, environmental problems and political concerns. Master teachers were employed to share how they get across mineral resource concepts in the classroom. Ninety-six percent of the participants stated that they had changed to a more positive perception of mining after taking the three day course.

Jan 1, 1995

By Eberhard Werner

Existing reports on the effects of mine subsidence on water wells and springs appear to be inconsistent. Some report quick and complete recoveries to pre-mining conditions while others indicate long-term or permanent effects. It is clear that topographic and geological factors as well as precise position with regard to the mine are important in determining probable effects of subsidence on aquifers. Ridgetop aquifers which are well above regional base-level are much more susceptible to disturbance by mining activities than those located topographically lower. Effects seen are attributed largely to increased permeability, both horizontal and vertical. of the aquifer rocks. The deeper aquifers usually show short term losses or water-table declines. but the effects on the ridge-top aquifers persist for longer periods or may be permanent. Subsidence enhances permeability. so that infiltrating water moves much faster to lower levels. causing pond and stream losses and declining levels in wells as well as declining flows of springs of the higher aquifers, while increasing levels and flows of the lower aquifers. Additional effects are shifts of spring locations caused by minor tilts due to differential subsidence and redirection of shallow flows by changes of horizontal fracture permeability. These effects are seen as mining of a panel progresses beneath the site. and are often repeated when adjacent panel mining fronts pass the site. Analysis of water well level and spring flow records indicates that the effects are greatest at the edges of longwall panels in the tensional regime. These effects are amplified for locations close to topographically steep terrain and in close proximity to fracture traces mapped from medium-to small-scale aerial images.

Jan 1, 1986

By S. A. Kupferman

Cement raw materials used in southern California and Arizona cement plants occur in a wide variety of geologic environments. Limestone, the primary material making up 75-80% of the raw materials mix used in cement manufacture, is mined solely from Paleozoic Era deposits. During this time, 570-245 million years ago, vastly more limestone was formed in California and Arizona than at any other time (continent was in southern latitudes). The general geology of each limestone deposit associated with the eight southern California and two Arizona cement plants will be reviewed. Many of these deposits are geologically complex, having been subjected to Mesozoic deformation, metamorphism and instrusive events, along with Cenozoic uplift and deformation. All of the cement plants in this region require the use of secondary additives in order to meet the chemical requirements for cement. The kinds of additives vary greatly, depending upon the chemistry of the limestone deposit, cement specifications, and the cement manufacturing process. In some cases, clay deposits with suitable chemistry on or near the limestone sources are utilized. Where alkali limitations or need for alumina-rich materials exist, then specialty clay deposits are used. Iron-rich sources in the region include iron ore deposits and slag or mill scale from local steel mills. The geologic setting and location of these additives, along with gypsum and silica-rich deposits presently in use, will be mentioned.

Jan 1, 1987

By Drupad B. Desai, James G. Gallanes

A key component of the Inland Feeder Project is the Riverside Badlands Tunnel, a7.9-mile stretch subjected to high internal and external hydraulic pressures passing beneath highly eroded hills in a semi rural environment. The tunnel presented significant design and management challenges to the project team. This paper describes the formula for project success used to manage the design of this complex pressure tunnel, from team member selection to the completion of all contract documents, on schedule and below budget. The project team dealt with sensitive regional and local community issues and won the trust of the community. The team included participation by senior management and recognized experts from inception to finish. The team worked diligently to build quality into design and adopted a claims avoidance approach to management and preparation of documents.

Jan 1, 1997

By D. J. Kennedy, A. W. Stokes, W. G. Klinowski

Sulphur hexafluoride (SF6) has become an accepted standard in the field of mine ventilation tracer gas studies. It has a wide variety of uses for defining mine ventilation flows that cannot be adequately described using conventional instruments such as anemometers and smoke tubes. The Cape Breton Coal Research Laboratory (CBCRL), Energy, Mines and Resources Canada, has been using SF for the past 4 years and has developed numerous release and sampling systems to increase its versatility. The CBCRL has also completed a successful field trial of an automated rapid sequential SF6 analyzer (which gives a pseudo real-time readout) that can be used underground. In doing this work, the authors recognised the potential of being able to use more than one tracer gas simultaneously in an underground study. Two alternative tracer gases (Freon-13B1 and Freon-12) have already been used by CBCRL in some of their underground work. These gases can be measured by gas chromatography utilising an electron capture detector in a similar manner to SF6. A description of these gases, the methods for 6&apos; their handling, release and sampling are given in this paper together with a brief outline of the analytical system used to measure them. Their suitability to mining applications is compared with SF6. A study in which these three gases were used together is discussed and the results and conclusions given. Some of the additional uses for multiple tracer gases to assist the mine ventilation engineer in resolving problems and improving his day-to-day monitoring are discussed. Finally, a brief analysis of developments which can be expected in the near future is outlined.

Jan 1, 1987

By Kenneth G. Knight, Frank L. Lynch

It&apos;s 12:30 A.M. The day before had been a long one with problems ranging from proper application of shotcrete during cold weather and the follow-on precautions for curing, meetings with city officials to avert a job shutdown because traffic wasn&apos;t being maintained properly and finally a briefing before METRO&apos;s General Manager to bring him up to date on projections for meeting the operational date of June 1975. The phone rings and Officer Jones of the Park Police says "Mr. Lynch, this lady in the apartments overlooking the jobsite is complaining of noise and she wants the job shutdown". "Officer Jones, have you called the Project Manager or the Resident Engineer?" "Yes, sir, but there is no answer!" "O.K., Officer, I&apos;ll check it out." In calling the job, I can only get the guard, because the inspector is in the tunnel. After some time, the guard calls back and says he doesn&apos;t know the way down into the tunnel. I have since had a difficult time believing that one. In the interim I finally reached the Resident Engineer and explained the situation. And finally at 1:30 A.M. the inspector called the Resident to say that the Park Police stopped the job at 1:00 A.M. because we didn&apos;t respond promptly. A similar situation had occurred some 2 years previously. With great expectation, noise specifications were developed to correct the earlier situation that had occurred. These newly developed specifications were in force at the time of this most recent shutdown. Common sense would tell you that even though we had developed and implemented, we believe, some of the best and most practical noise specifications in construction practice today, we had not enforced them. What caused the shutdown - a noisy

Jan 1, 1974

By H. Dho

Two aromatic-type chelating agents, 1,10 phenanthroline (phen) and 8-quinolinol (quin), were tested as specific depressants for magnetite in the cationic silica flotation of magnetic taconite concentrates. Micro and batch flotation tests, along with zeta potential and adsorption measurements were used. In the presence of a cationic collector, dodecylammonium chloride (DAC), the Fe/phen surface chelate electro-statically repelled DAC, and magnetite was depressed. The negatively charged Fe(quin)2(OH)2-on the magnetite surface attracted the cationic collector and made magnetite floatable.

Jan 1, 1995

By J. A. Folinsbee

Placer Dome Canada owns and operates the Campbell Mine at Balmertown, in the Northwestern corner of the Province of Ontario, Canada. The mine operates at 1500 stpd and produces in excess of 300,000 oz of gold annually. Recent changes to the gravity concentration circuit have resulted in a 10-15 % increase in gravity recovery. The circuit changes responsible for these improvements will be the focus of this paper.

Jan 1, 1997

By Dean H. Herrick

The production of crushed stone in the United States has exceeded 1.0 Gtpy since 1987. Eighty percent of the crushed stone produced is used in the aggregate industry, accounting for over half of the quantity of natural aggregate consumed in the United States. Approximately 718 of the crushed stone produced in 1989 was limestone and dolomite followed by granite, traprock, sandstone and quartzite, miscellaneous stone, marble, shell, calcareous marl, volcanic cinder and scoria, and slate in order of descending volume (Table 1). Of the remaining 20% crushed stone produced in the United States and not used as aggregate, 12% is used in the manufacture of cement which is an important construction material. Only 8% of crushed stone is used in specialty products not associated with the construction industry. Therefore, this chapter will concentrate on crushed stone as used in aggregates, with occasional reference to other uses or to chapters which discuss specific nonconstruction uses of crushed stone. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass by the addition of cementing or binding materials that produce a concrete by compaction, or by natural weight to produce a road or foundation fill. Aggregates are usually from 80 to 100% of the material volume of the construction masses in which they are used. Conditions necessary for a rock deposit to be developed for construction crushed stone include: Quality-should pass rigid specifications for strength and durability; Quantity-adequate volume of rock is needed to have a production life of at least 10 years, preferably 20 or more years; Market-must have adequate market to support a new crushed stone operation; Transportation-transportation cost must be competitive for the intended market; Environmental-the impacts of mining, processing and transportation of crushed stone on the environment at or surrounding the mine site must be within acceptable limits; Permitability-mining, processing and transportation of crushed stone must usually be permitted by governing agency. The following discussion will touch upon all facets of crushed stone operations from the mineral deposit and its geology to technology, uses, economic factors and end with governmental regulations of mining crushed stone. The sections are not designed to answer all questions, but rather to be an introduction to the crushed stone industry. Where more information is required, The Aggregate Handbook by Barksdale (1991) is recommended as the best general source.

Jan 1, 1994