Search Documents

By J. Slivnik, A. Stergarsek

[The site] [Z]irovski vrh uranium ore deposit is located in the extreme north-western part of Yugoslavia, some fourthy kilometers from the capital of Socialist Republic of Slovenia, Ljubljana, not far from the Italian and Austrian border. The sandstone type deposit of uranium ore with medium grade is located in a foothill of Julian Alps. The site shows some typical conditions for this region, which demand special attention in respect to the incorporation of an uranium treatment facility into environment. Among these specific conditions the following site characteristics should be mentioned: - populated area of agricultural and recreational value, - unconvenient climatic conditions with excessive rainfall and long lasting temperature inversions in the winter time, - very pure surface and underground waters which supply the drinking water reservate for large area including the capital of Slovenia, - sharp relief, - unconvenient geological structure. The choise of technology The intention to produce uranium and at the same time respecting the natural characteristics and existing uses of the site made the design of the ore treatment facility relatively difficult one. In general, there were two basic alternatives available perform the task. First alternative was to adopt the usual technological flowsheet with wet tailings disposal and with discharge of used water i.e. liquid effluents into the river. In order to prevent the negative impact of such technology on the sourrounding area sophisticated water purification installation and costly measures in wet tailings disposal e.g. impermeabilisation of large areas by concrete injections, large dam constructions, uncertain capturing of the water sources should be employed. Second alternative was to modify the usual flowsheet by employing the maximal recycling of liquid effluents to the process and to dispose the solid

Jan 1, 1980

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By D. J. Dunn

Grinding balls, simple in shape, are actually sophisticated machine components and essential elements of mineral grinding mills. Their physical properties and quality must be adequate to achieve design life and grinding mission with few failures. Consistent properties and freedom from breakage are essential. Size, mass, hardness profile, chemistry, and microstructure are important variables that should be designed, specified, controlled, and verified to achieve optimal mill performance. Failure to specify ball properties in detail or failure to obtain required ball properties and quality can cause milling productivity losses and excessive costs that could endanger a milling operation's survival in the competitive mineral industry.

Jan 1, 1990

By Jennifer B. Leinart

With the signing of the North American Free Trade Agreement (NAFTA), Canada, the United States and Mexico entered into an international experiment in economics amid a cloud of controversy that still lingers. Central to the controversy are the disparities in wages that exist among workers in the signing countries. Wage surveys completed by Western Mine Engineering show the degree of disparity that exists among the mining industries of those three countries. Labor costs constitute 30% to 50% of operating costs. So these wage differences are a matter of interest to the mining industry. It is unclear how much of a factor they are in determining where companies search for and develop new mines. That depends on where minable deposits are expected to be found. However, a deposit that may not be minable in the United States or Canada may be minable in Mexico because of lower labor costs. Some adjustments are anticipated for the Mexican mining industry if and when its wages begin to approach comparability with US and Canadian wages. Table 1 combines the results of four recent surveys. It lists benchmark wages for mining job titles common to all the countries. About 220 mines are covered by the combined surveys. Canadian miners' wages, converted to US dollars, are typically 75% to 95% of US wages, while Mexican miners' wages are less than 10% of those in the United States. Table 1 also shows that wage disparities are not confined to international borders. In fact, the difference in average wages between the US coal industry and the US metal and industrial mineral industries is greater than between the Canadian and the US mining industries overall. Table 2 shows that managerial, technical and administrative salaries show similar, but less pronounced differences among the three countries. Salaried personnel at Canadian mines earn 80% to 90% as much as their US counterparts, while those in Mexico earn 20% to 30% as much. Here again, average US coal salaries exceed average salaries for the US metal and industrial mineral industries.

Jan 1, 1998

By Timothy N. Dunne, Joseph M. Gonzalez

This paper presents the case history of a comprehensive geotechnical investigation for the Crosstown Transport Facility, a 10,880 m long, 3.2 m diameter pressure tunnel proposed for construction in San Francisco, California. The proposed tunnel would be part of the City and County of San Francisco's Clean Water Program, and its purpose would be to convey stormwater and sewage from the east side of the City to the Pacific Ocean. Tunneling conditions were defined by surface geologic mapping, 94 exploratory borings, surface and borehole geophysics, aquifer testing, Goodman Jack testing, pressuremeter testing, and laboratory testing. Through the use of advanced coring techniques and a strictly controlled drilling fluid system, core recovery averaged 90 percent in the sheared and fractured rock of the Franciscan Formation. As a result, over 1,400 linear meters of rock core was recovered and is available for examination.

Jan 1, 1983

By J. Keng, S. T. Chen, T. M. Shih

Kwanyin Tunnel is presently the longest (7.7 km) railway tunnel in Taiwan. Due to heavy railway traffic, a pass-by station will be built inside the tunnel to increase the traffic flow. Since the concentration of toxic gases released by the locomotives may reach dangerous levels, a research program was conducted for the purpose of designing a ventilation system which could dilute and/or remove the toxic gases to maintain an acceptable pollutant level. The program consisted of two parts. The first part was field measurement during which the concentrations of pollutants and wind velocities were measured at various points inside the tunnel to acquire basic data regarding ambient air quality, piston effects for the different types of trains, and existing ventilation conditions. Weather data (temperature, humidity, atmospheric pressure, wind direction and velocity) were gathered at many stations, both on the surface and inside the tunnel. The amount of pollutants released by each type of locomotive for various conditions were also measured. The second part of this study involved establishing mathematical models for predicting the air quality of the various proposed ventilation systems. Three different models were used for this work. The first one is a piston effect model which assumes that the gases and air undergo immediate mixing inside the tunnel. The second one is also a piston effect model which assumes that the diffusion ability of the gases is zero. The third one is a conventional ventilation model which was used for natural and mechanical ventilation conditions. From the result of field measurement and mathematical model studies, a ventilation system was chosen with consideration of both ventilation effects and construction costs.

Jan 1, 1987

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator's training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By Michael J. Rinker, R. V. Nicholson

Waste rock and tailings from a proposed nickel-copper mine were evaluated extensively for potential on-land and under water disposal. Standard humidity cell and column tests were conducted over a two year period and underwater tests were conducted for more than one year. Nickel concentrations or release rates from the waste were consistent with nickel to sulphur ratios in the solids. This relationship provided a tool to assess the risk of metal leaching in wastes using nickel and sulphide assays. Nickel release and mobilization was found to occur for both oxidizing leach tests and under water tests even when pH values exceeded 7.0. Geochemical model calculations showed that iron oxyhydroxide solids can scavenge nickel from leachate and that the nickel inventory can be released from solids at relatively lower, but neutral pH values.

Jan 1, 2000

By George L. Baloo, Dave Kwiatkowski, Jose G. Cañlzales

Capital project funding for a medium to large materials handling project often includes a budget for procurement of supplier-recommended spare parts, and it is the Project Team's responsibility to select these parts. With today's economic climate, limited budget, and other factors, the spare parts selection process is a difficult and arduous effort. This decision carries with it a risk to plant operations and in some cases the commodities producers. Too often the decision-making process is not documented, and the reasons for eliminating and reducing quantities are based on "best guess " Recently on the Solids Handling Phase 2 Project in Jose, Venezuela, the Project Team took a unique approach to this problem. This paper discusses the analytical approach taken by the Project Team, the database system that was developed to manage this problem, lessons learned, and their applicability to pre- project planning and preliminary design.

Jan 1, 2004

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behavior during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behavior of an ore in a concentrator, pilot plant or bench test: and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1992

Engineering programs usually do not provide sufficient opportunities for students to develop written communication skills. The responsibility for developing those skills is frequently delegated to the humanities faculty, who in a single technical writing course are supposed to transform engineering students into proficient communicators. A general template which was developed for report writing in our senior level capstone design courses is discussed. Students have improved their writing skills by using the template. The writing assignments have provided the students the opportunity to write and revise more technical reports that communicate their design.

Jan 1, 1995

By Erik Westman, Enji Sun, Xu Ma, Ben Fahrman

"Shale gas has become an increasingly important clean energy, which has been explored worldwide in recent decades. Supercritical CO2 acts as fracturing fluid for shale gas production. The safety monitoring is essential to prevent any kinds of leakage from the reservoir as the supercritical CO2 physically stored hundred kilometres underground. Seismic tomography is an imaging technique that uses induced seismic waves to create three dimensional images of the subsurface. It is an effective monitoring method to evaluate the caprock integrity in the carbon dioxide sequestration storage (CCS). In this experimental research, a simulated uniaxial compressive load is applied on a granite sample to analyze the stress redistribution for long-term in-situ caprock integrity during CO2 injection. The induced seismic waves are recorded and seismic events are traced based on the Geiger algorithm. The frequency of seismic events correlates with the caprock failure evolution. The acquired seismic data is divided into four regimes based on the frequency of seismic events and the failure process to examine the failure evolution. Furthermore, the travel time and distance is plotted to analyze the variation of velocity. Finally, the double difference tomography (TomoDD) algorithm using arrival time is adopted to recalculate the locations of seismic events and velocity structure in each regime. The results indicate that the passive seismic system can map the caprock stress distribution and allow for imaging of the caprock integrity. TomoDD exhibits sound improvements to relocate seismic events both in relative and absolute locations as well as to characterize the local velocity structure. The study further reveals that seismic monitoring along with TomoDD could evaluate the caprock failure accurately in the CCS.Introduction To reduce the CO2 concentration in the atmosphere, CO2 capture and sequestration (CCS) has been suggested to as a means of continuing to use fossil fuel resources while offsetting their negative environmental impacts (Eiken et al 2011). A positive CCS project should retain 99% of the injected supercritical CO2 (pressure is greater than 7.38 MPa and temperature is above 31.04? and a density is of about 700 kg/m3) over at least 100 years (Davidson et al 2005). As large quantities of supercritical carbon dioxide are being injected into full scale storage projects, caprock stress is redistributing and the leakage could occur anywhere over a wide storage area (Hou et al 2012). Acoustic waves are emitted from the caprock, as it fractures due to the CO2 injection, which can be detected by passive seismic sensors (Shitashima et al 2013). Tomography techniques are advantageous for imaging the integrity of the caprock in the CCS projects. Velocity tomography uses waves to model entities based on the arrival time of waves (Westman et al 2001, Westman 2004, Luxbacher et al 2008). Seismic tomography is a data inference technique that exploits information contained in seismic records to constrain 2D or 3D models of the Earth's interior. It generally requires the solution of a large inverse problem to obtain a heterogeneous seismic model that is consistent with field observations (Kudryavtsev et al 2012)."

Jan 1, 2017

By R. H. Seraphim

The name is derived from an Egyptian myth, "A beautiful lone bird which lived in the Arabian desert for 500 or 600 years and then consumed itself in fire, rising renewed from the ashes to start another long life." HISTORY This account of the first history is gleaned from old reports and documents which are listed in the Bibliography and from discussions with old-timers of the district. Prospectors were active in the vicinity of Greenwood in 189 1, and in that year staked the Mother Lode, Crown Silver, and Sunset. Henry White staked the Knob Hill claim in Phoenix on Jul. 15, 1891, and by the end of the year, other prospectors had staked most of the claims covering the valuable ore bodies in the camp. Much surface work done in the early years indicated that the values in copper, gold, and silver were low. Large capital investments were required to develop the ore bodies and build smelters. The discovery that the ore was practically self-fluxing greatly enhanced the value of the deposits. A map of the area showing the geology is given in Fig. 1. The bedded Brooklyn conglomerate is shown in Fig. 2.

Jan 1, 1991

By J. A. Herbst, T. I. Martinovic, Y. C. Lo

This study was concerned with the application of a computer simulation methodology to optimize the performance of mills grinding iron ore concentrate prior to pelletizing. The methodology involves batch and plant testing, modeling and computer simulation. The analysis of grinding performance was carried out and capacity increases were predicted in the context of detailed population balance models developed for the plant ball mills. Model developnent and plant confirmation were performed using data obtained in a series of batch tests and three plant tests. From experimental data and computer simulation it was found that ball size, percent solids and classification all had a significant effect on mill throughput. Based on the findings of this study, a 12-152 increase in capacity was predicted to be available by a proper combination of ball size charge and optimum percent solids. These predictions have been confirmed by plant tests in which the recommended operating changes have been made.

Jan 1, 1990

By Zhang Youdi

According to general guidelines, deposits suitable for surface mining can be divided into two basic categories: horizontal or flat-bedded deposits and inclined or dip-buried deposits. A series of mathematical models for surface mine long-term planning (SMLTP) has been developed and can be used for any kind of deposit. The basic theory and methodology of the models are oriented- graph simulation which combines graph and network theory with a systems simulation technique to form a new approach. From the viewpoint of surface mining and long-term plan modeling, the main differences between the two categories of deposits are analyzed, an important algorithm is put forward, and the structure of the models and some results of applications are introduced. Dynamic and comprehensive optimizations have been completed by the SMLTP model series. Combining different OR branches, the new approach has been proved to be a powerful tool to solve the strategic problems of surface mine planning.

Jan 1, 1989

By H. Lyn Bourne

This is the 12th year for this column and the 11th in which the royalty data have been tabulated. This year adds 20 to 30 new entries. There are, however, some deficiencies that the readership hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. There are several states where no royalty information was available for either commodity. Readers can help share information about these missing states, so next year there will be fewer states without information. Severn Brown again sent helpful information from the Prospectors and Developers Association of Canada (PDAC). The summer 1992 issue of PDAC Digest recommended"... the most useful technical paper ever published for economic geologists...." "Net smelter return models and their use in the exploration, evaluation and exploitation of polymetallic deposits" was written by R. Goldie and P. Tredger (Geoscience Canada, Vol. 18, No. 4, pp. 159-171). Last year's column described leasing practices in Russia. Some new information has been gathered since then. Kirill Kavun is the managing director of the International Geoeconomic Center in Moscow. He sent two publications from 1992-"Regulation on the procedure of licensing the use of the subsurface," and "Law of the Russian federation on the subsurface." Both are supplements to the magazine Mineral Re¬sources of Russia, Economics and Management.

Jan 1, 1993

By Scott G. Britton

Thin-seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges can be further amplified depending on such factors as labor unions, federal and state regulations and market characteristics. This article explores the turnaround situation occurring at Tanoma Mining Co. (TMC), a medium-sized, underground coal mining company in central Pennsylvania. The company has used a systematic approach of improving management controls and direction, labor relations and communications to improve its cash flow from negative to positive within a projected five-year span. An intensive upgrade-rebuild-replacement program for mining equipment and systems has also been established to support other management activities. Discussion Thin-seam coal mining is an industry within the broader industry of coal mining. Thin seam mining faces the same cost pressures and engineering problems as its higher-seam competitors, without the advantages of moving volume per foot of extracted material. To stay at economic parity with others requires additional creativity within the management team to extract higher productivity gains from the existing workforce and mining systems. The Tanoma operation is a deep mine in Indiana County, PA, about one hour northeast of Pittsburgh. Coal is extracted from the Lower Kittanning "B" seam. It lies about 91 m (300 ft) below the surface and averages 0.9 m (I ft) in height. Continuous mining units using mobile bridge conveyors or shuttle cars

Jan 1, 1991

By Mary B. Ansari

The literature of mine ventilation is very diverse in nature, widely interdisciplinary, and extremely international in scope. Important references are found in indexes, abstracts, government documents, technical reports, journals, conference and symposia proceedings, and monographs. In this decade computer searches of the literature have greatly aided researchers in finding needed items. There is, however, no convenient summary of recent English language literature in coal and non-coal mine ventilation. This paper attempts to fill that gap in the literature. Because of the worldwide provenance of the subject and the attendant publication deluge, this paper covers only current English language publications on ventilation. The writers have examined the field's English language abstracts, indexes, bibliographies, periodicals, technical reports, books, and symposia and conference, proceedings. The survey also considers the field's most important bibliographic data bases. It should be noted that addresses for many of the literature sources listed in the paper are given in the section on literature and data base information sources.

Jan 1, 1980