Search Documents

By S. K. Nandy, K. F. Unrug

The behavior of the immediate shaly roof within a drift mine in eastern Kentucky, operating in the Coalburg seam, was monitored with roof bolt dynamometers. The dynamometers used were capable of providing readings up to a maximum load of 66.72 kN (15,000 lbs), + 0.022 kN (5 lbs). To observe the influence of moisture on the rate and extent of roof deterioration, 57dynamometers were installed on roof bolts anchored in intake and neutral airways. Monitoring was conducted during the period January 1985 through January 1986, in order to cover a full cycle of dry and wet mine conditions associated with seasonal changes. Analysis of the data showed a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1987

By St. E. Deák

There is a large preoccupation concerning the development of expert tools (ET) in the mining industry, in order to minimize the impact from waste dumps and processing residues on the environment. In this paper, the authors present a new approach for the development of an expert tool for each area under study, in order to minimize production and disposal of mining wastes on the environment, by taking into account the DKRControl method as well as the Ecomining principles, regarding among others hazard identification, impacts and monitoring. Due to the complexity of this topic a reliable ET requires input from a number of interested stakeholders. The design and management of a mining waste disposal site over its entire life cycle is also considered very important.

Jan 1, 2008

By L. W. Saperstein, M. C. Radomsky, D. L. Passmore, J. D. Bennett

About 60 small surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the degree of safety exhibited by workplace behavior and conditions. Data were collected through the use of on-site safety instruments covering seven major occupational positions typical of small surface mines. Workplace events observed (acts and conditions) were assigned a hazard classification. Feedback was initiated to improve safety performance in areas failing to conform to appropriate safety standards. Results suggest that the variety of unsafe acts and conditions associated with the companies observed are extensive. Further, the experiences drawn from this pilot project have proven the need to pursue this behavioral approach. Future research should concentrate on subjecting the present approach to a strict experimental design involving randomly selected “poor risk” mines.

Jan 1, 1987

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about 1 m (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1987

By S. K. Kawatra, H. L. Dilley, W. W. Wen, T. C. Eisele

To improve the sulfur-rejection capability of a coal-cleaning plant, it is first necessary to evaluate the performance of the existing circuit. This information can then be used to decide whether there would be significant benefits from improving the operation and control of the existing circuit, or whether further improvements would require more radical process changes. This paper describes a simple model for evaluating heavy-media separation circuits, and presents a case-study of such an analysis of an operating heavy-media coal cleaning plant. Efficiency curves were calculated and modelled using Lynch's method, and a simplified expression was derived for calculating the Ecart Probability value from the model parameters.

Jan 1, 1995

By R. J. Sweigard, R. V. Ramani

Estimated costs and revenues can be used in evaluating postmining land use alternatives. However, postmining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact on each alternative under consideration. In this paper, a method is presented that employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1988

By G. Y. Li, D. Farahmand

The dilemma of a numerical analyst not only concerns the problem of modelling the non-linear behaviour of intact rock, but also the non- linearity contributed by structural discontinuities. In this light, it is the intention of this paper to examine some aspects of the non-homogenity and structural discontinuities of rock and incorporate this behaviour into boundary element numerical solution. Non-homogeneous material is considered piecewise, thus homogeneous and is modelled by using sub-regions. The Mohr- Coulomb failure criterion is employed to model the non-linear behaviour of the major discontinuities. A computer program is developed based on the procedure for combining the direct boundary element method and the displacement discontinuity method. A linear element type is employed in the formulation of numerical solution. The computer program is used to study the stress distribution in a gold mine.

Jan 1, 1986

By Chinmoy Sarkar

Mining organizations have been trying to employ best practices at exploration, exploitation and processing level to increase productivity in the supply chain. Traditional techniques of cost control can no longer meet the ambitious target of mine managers. An integrated perspective of Mining Value Chain with enterprise-wide application of information technology (IT) ensures the ability of every mining processes to improve energy, land, capital and labour resource performance while continuing to cut costs and achieve profitability. IT offers enormous potential in mining industry at shaping entirely new opportunities to create value. This paper characterizes important entities of Mining Value Chain and attempts to provide a vision on how IT can transform the mindsets of industry managers addressing the needs of the customers.

Jan 1, 2002

By Mario E. Rossi

The concept of entropy is classical in thermodynamics and information theory. Its potential use as a measure of the ordering of a spatial system is discussed. Although entropy has been discussed previously in the framework of spatial statistics and for univariate distributions, a bivariate data-based estimator has not until now been defined. Different statistical distributions maximize entropy, depending on the univariate, bivariate, or n-variate constraints applied. For bivariate distributions, with a known mean and known covariance, it can be shown that the distribution that maximizes the entropy of the system is the bivariate gaussian. A nonparametric bivariate entropy estimator is introduced, derived directly from the experimental cumulative frequency distribution. Assuming that this experimental bivariate distribution is representative of the population distribution, then a measure of departure from gaussianity can be introduced as a relative entropy estimator. Practical applications for the entropy estimator are discussed, and an example developed.

Jan 1, 1992

[Costs may be classified according to their source and behavior: Scale of aggregation - Total costs - Unit costs Time period for which the costs are charged - Product costs - Period costs Controllability and relevance for decision-making and control - Controllable costs - Noncontrollable costs - Sunkcosts - Opportunity costs Their basic source - Production costs (also termed manufacturing costs) - Nonproduction costs How the costs change with changes in activity - Fixed costs - Variable costs - Semivariable costs Traceability to individual units of production - Direct costs - Indirect costs Use in planning (budgeting) and subsequent control - Standard costs - Normal costs ]

Jan 1, 1999

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models have the potential to be used to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1993

By Robert L. Cascio

The mining industry uses a large amount of electric power. Their equipment is subject to extreme environmental conditions and mechanical shock. A significant number of electrical accidents are a result of improperly grounded electrical equipment. Federal regulations require the safety ground bed resistance to be measured once a year or after modifications. Most commercially available instruments used to measure the ground bed resistance require the ground conductor to be disconnected and the power system disconnected for safety reasons. The "fall of potential1' method requires auxiliary ground rods and approximately two hours to complete the test. Although a new instrument was initially thought to measure the ground bed resistance immediately without isolating the ground bed, field tests have shown this method is not accurate. In some cases, a continuous measurement of the ground resistance is desired. A monitor has been developed and is presently being evaluated at several mines. These installations will be discussed.

Jan 1, 1992

By Bruce T. Stanley

Though most porphyry-molybdenum deposits lend themselves to various reserve estimating techniques, still there must exist the constant effort to not merely obtain an estimate but rather to obtain the best estimate. To answer the challenge of a complete ore reserve estimation, one must attack the problem with the purpose of obtaining the results closest to reality. What we wish to determine is simple: metric tons (short tons), grade, and kilograms (pounds) of molybdenum contained. In order to effectively accomplish this task, further consideration must be given to the ease of using the information obtained and its inherent reliability. The only known method for ore reserve estimation that supplies the needed results along with its distribution and a measure of confidence provided by sound mathematical backup is geostatistics. The following review is an example of geostatistical application of an ore reserve estimate at the AMAX Henderson mine demonstrating technique, viability, and usefulness of results.

Jan 1, 1979

By T. M. Campoy, J. R. Jones

When extending the life of an existing mine in Appalachia, it is common to acquire the adjacent reserves and extend the existing mine into it. The existing mine is often renovated to accommodate the new conditions. The existing mining system and the track and belt haulage systems may he modified while the new property is integrated into the old one. All of these changes create new constraints for the mine ventilation system (MVS) that require proper planning and control procedures. This paper presents a study that was carried out for the ventilation system of a newly expanded underground coal mine in the Appalachian region. The process of correcting the ventilation system of the existing mine is discussed. That is followed by a discussion of some of the stages of controlling the expanded system. Numerical data for these steps are also presented.

Jan 1, 1994

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining in usage in the mining industry. A variety of machines are now being used, including tunnel boring machines, roadheaders, continuous miners, surface miners and augers. These machines have advantages compared to drill-and-blast mining methods, including increased safety, lower cost, uniform muck size and accurately sized openings. A century of experience with mechanical methods has paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hard-rock mechanical mining machines. When several significant challenges have been met, mechanical miners will become integrated mining systems and will determine the design of mines.

Jan 1, 2002

By C. W. Schultz

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained.

Jan 1, 1991

By M. E. Breitrick

Newmont Gold operates the Carlin East underground, one of four underground gold mines the company operates in northeastern Nevada. Carlin East began full production in early 1995. The mine's current rate is 900 t/d (1,000 stpd), producing about 4.6 t/a (150,000 oz/year). About 125 hourly and salaried personnel are employed at the project for its estimated six-year mine life. Two mining methods are currently used at the Carlin East Mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased an AC-Eickhoff ET-210 roadheader. The machine went into service in mid-June 1997. It is used in longhole Stope topcut development and cut-and-fill production at a rate of 225 t/d (250 stpd)

Jan 1, 1998

By Markku Virtanen, Pertti Koivistoinen

From the perspective of a large mining company the comminution circuit design is worth keeping within the boundaries of the organisation. The correct circuit design begins from the understanding of the role of grinding. Grinding is a link only in the long "comminution chain," starting from solid rock and ending at the concentrating stage. The final target in comminution is to take a part in the maximization of Net Smelter Return, which goal provides the simultaneous considering of capital costs, operating costs and the economic effect of process results. As a general rule there will be a single crushing stage only, ahead of the grinding process. Grinding does not use any metallic grinding media at all, and there will be fine crushing for critical material in the grinding circuit. Grinding has a minimum two stages, besides, at many concentrators middling products and quite often also tailings are reground.

Jan 1, 1997

By M. C. Williams, T. P. Meloy

For over thirty years the Population Balance Model, PBM, has been the mainstream modeling method for comminution unit operations and comminution circuits. For commercial comminution circuits the method is based on erroneous physics and dubious numerical mathematical methods leading to non unique solutions that have little extrapolative value and faulty control strategies. In short the PBM is wrong. Given is a detailed analysis showing a number of non trivial flaws in the linear PBM. Moreover, a simpler model is presented that leads to a solution of the comminution circuit predicting the size distribution output over a variety of conditions. Because the linear PBM is firmly entrenched, an award is offered, $10,000, to any researcher that can use the linear PBM and its present numerical methods to predict the typical straight line, self similar, output of wet mills over a variety of grinding times.

Jan 1, 1992

By Kathleen S. Smith, Katherine Walton-Day, James F. Ranville

Four different scales of observation were used to evaluate the potential effects of a fluvial tailings deposit on water quality along the flood plain of the upper Arkansas River south of Leadville, Colorado. First, we collected surficial material and subjected it to batch water-leaching test. Second, we excavated and leached an intact eight-inch diameter core. Third, we examined the water quality of the shallow ground water beneath the fluvial tailings deposit, and fourth, we monitored water quality along a 5-km reach of the adjacent Arkansas River. Leaching of surficial samples indicates that there is a reservoir of readily water-soluble material yielding elevated metal concentrations and high acidity. However, there are minimal measurable water quality effects of the fluvial tailings deposit on the adjacent reach of the Arkansas River.

Jan 1, 2000