Search Documents

By Linda Frederick

In July 1997, Krupp Canada obtained the contract to design and supply the conveyor system for Chile's Los Pelambres copper mine expansion project. Progress on the overland conveyor system is currently on schedule. It is a challenging task to convey copper ore from an open-pit mine located on a mountain site 3,000 m (9,840 ft) above sea level down 1,300 m (4,265 ft) to the processing plant at the valley floor below. The Los Pelambres conveyor system moves copper ore at a rate of 8.7 ktlh (9,600 stph) and at a speed of 6 ml sec (1,180 ftlmin) for 12,750 m (41,830 ft). The distance is divided in three conveyors, each 1,800 mm (71 in.) wide. The largest conveyor is 6 km (3.7 miles) long. To protect against avalanches and rockslides, the conveyors run through a 12-km- (7.4-mile-) long tunnel system. The lowest of the three conveyors is equipped with a shuttling head end. With this, the conveyor discharge point can be moved back and forth by 100 m (330 ft), allowing it to build up a longitudinal stockpile at its end. To meet the extreme design parameters, the limits of conveyor design had to be pushed to record-setting marks. For instance, the ST-7800 steel cord conveyor belt is the strongest belt ever installed in a conveyor system. A total drive power of 25 MW (33,535 hp), consisting of 10 2.5-MW (3,352-hp) drives, is included in the design plans. In loaded condition, the electric motors act as generators and feed electric energy back into the power grid. The motors are controlled by variable frequency inverters that provide an infinite adjustment of motor speed. This technology allows starting and stop- ping the conveyors precisely along predetermined acceleration and deceleration ramps. This is done so harmful belt jerking and stress waves can be avoided.

Jan 1, 1999

By M. Abdi Oskouei

Some believe that Sustainable Mining due to impermanence of mining operation and adverse environmental impacts of mining, is an oxymoronTruly, no one can overlook these environmental impacts; however, a sustainable development is based on three elements Environmental, economical and social sustainability. In order to assess the relation between mining activities and sustainable development, not only environmental but also economical and social sustainability must be considered.Thanks to mine reclamation the adverse impact of mining on the environment can be reduced, meanwhile it will improve the social and economical condition after the mine-closureTo ensure that a mining operation is toward sustainable development goals, specific criteria and indicator frameworks have been established, in addition, for verification of our discussion the suitable selected reclamation plan for Bibishahrbanoo limestone mine of Tehran-Iran and its effect on sustainability of region has been studied.

Jan 1, 2011

By J. R. England, W. J. Taylor

The Sudbury Basin is the scene of the mining operations of the Ontario Division of the International Nickel Company of Canada, Limited. Around the rim of the geological formation and within thirty miles of the City of Sudbury are located twelve operating mines and one open pit operated by the Company. The City, with a metropolitan population of some 100,000 lies 240 miles Northwest of Toronto. In addition, there is one mine in Northwestern Ontario, at Shebandowan, 700 miles Northwest of Sudbury. In 1973 these mines produced 16.5 million short tons of ore of which 14.9 million tons were from underground and the balance from open pit operations. Mining methods include blasthole, sublevel caving, induced caving, shrinkage, cut-and-fill and undercut-and-fill. Raise boring commenced at Inco in 1964 and is now applied at all mines in the Sudbury District (Figure 1). [ ]

Jan 1, 1974

By W. E. Cobb

The financial implications of environmental liabilities are becoming staggering, particularly for mining companies. The Environmental Protection Agency's (EPA) Record of Decision (ROD) list for Superfund mining sites has some pretty hefty financial commitments, such as the $10 million operable unit remedy for the Yak Tunnel at California Gulch (in Colorado) or the $40 to 60 million remediation at Bunker Hill (in Idaho). These costs are driven by the large volume and areal extent associated with historical waste management practices at mining sites. (It's difficult to have a low-cost remedy for a 20-square-mile site.) Unfortunately, there are other ways of generating environmental liabilities besides Superfund, such as non-compliance with Clean Air Act provisions, stormwater permits, or National Pollutant Discharge Elimination System (NPDES) permits. In the last 2 years, EPA has increased enforcement in its regulatory programs, which has resulted in increased fines and criminal actions. Leaders in other industries (primarily the chemical and manufacturing industries) are viewing environmental liabilities as a strong motivator to select engineering approaches carefully based on technical, legal, economic, and philosophical perspectives. Industry interest in waste minimization programs comes from the concept that it is economically advantageous not to create waste in the first place. Waste minimization programs typically balance increased front-end capital investment with the minimization of potential long-term environmental liabilities as a way to achieve the lowest total-or life-cycle-cost. A side benefit of waste minimization programs is that they tend to improve overall regulatory compliance. Waste management practices are also becoming philosophical, as evidenced by a May 11, 1992, Business Week article: Companies that incorporate innovative thinking on sustainable development will do more than clean up or prevent their own pollution. They'll make and distribute a product more efficiently than ever, worry about its lifelong environmental impact, plan for recycling, and get their suppliers on the bandwagon. This type of approach will require a new mind-set, new tools, and adjustments throughout the organization. A key aspect of waste minimization or life-cycle waste management programs is the incorporation of environmental costs into economic analyses that compare various waste management alternatives. However, the incorporation of environmental costs into an economic analysis can be more difficult than initially thought. As noted above, new tools-or even a new toolbag-are needed, such as new accounting methods that track and assign the true lifetime environmental costs of a particular product. One piece of the new toolbag is life-cycle cost analysis, which is discussed in this paper. To simplify the discussion, this paper looks at the total costs associated with a given mining site. The concepts presented in this paper, however, can be applied to any mine waste management decision. The ultimate extension of life-cycle costing, as presented in the Business Week article, is to include the potential environmental costs throughout the life of a metal. At this point, I am perplexed on why, let alone how, to include the potential downstream environmental costs (i.e., the costs associated with smelting, manufacturing, use, and recycle or disposal) throughout the life cycle of mined copper, lead, or zinc.

Jan 1, 1992

By Mucella Ersoy, Nese Celebi

Management Information System (MIS), is a system using formalised procedures to provide management with appropriate information to make timely and effective decisions. Before developing MIS, first functions of the organisation should be defined and grouped into subsystems. After determining the information required and produced by each system and interaction between subsystems, the related data resources should be structured into a series of databases and files. In this study, the MIS developed for Soma Open Pit Mines, Turkey is described in this respect. First, analyses of the existing system including user requirements and scope of the system are given. Then the designed information system, its subsystems, interaction between subsystems and system structure are presented in detail.

Jan 1, 2002

By Peter J. Alderson, M. P. Evans

The application of conveyor belting in bulk materials handling is crucial to the success of most mining enterprise selection of the cover rubber grade and thickness has a direct bearing on the cost per ton conveyed. Current and future demands placed on belt covers by higher speeds, increase capacities and greater lifts means today's cover will not be adequate for tomorrow's applications. The simple selections of RMA Grade I and I1 and MSHA above and below ground need to be expanded upon. This paper describes various new approaches for selecting conveyor belt covers for specific applications. It also presents examples of material and compounding techniques available to the belt manufacturer to improve the performance of their covers.

Jan 1, 1996

By Joel Lenz, Warren Hood, Jackson Jenkins

Whole ore or other process streams are being transported from mines to remote processing facilities for multiple reasons, such as improved project economics, maximum utilization of capital, and minimization of environmental risk. Case studies will be presented from a variety of operations. Glenbrook Nickel processes ore from their deposit and receives ore from New Caledonia, crushes and dries the ore, and transports it inland to the smelter. The Mule Canyon and Rosebud ore bodies truck-haul their ores to the Lone Tree and Twin Creeks processing plants. Pegasus Gold hauls their Diamond Hill ore to their Montana Tunnels facilities, and Sierrita pumps solution to an existing tank house 8 miles away for electrolytic recovery.

Jan 1, 1998

By G. H. Schnakenberg

In 1986, the US Bureau of Mines (USBM) embarked on a major research effort to develop technology that could substantially reduce worker exposure to face hazards by simply relocating the equipment operators to an area of relative safety. This reduced-exposure mining system (REMS) research effort enhances the USBM's ongoing health and safety efforts aimed at reducing and controlling dust and noise and reducing accidents through training and better mining practices. This paper reports on the progress made on the developing research and demonstrates the technologies required for the computer-assisted teleremote operation of continuous mining machines, haulage systems and roof bolting machines.

Jan 1, 1998

By L. Landryova

The Department of Control Systems and Instrumentation, VSB - the Technical University Ostrava, has been involved in a project dealing with utilization of landfill gases, when the methane gas utilization and minimization of its release into the atmosphere was the main concern. The landfill site is generally a place, where technology for energy production can be built. The conditions for this technology implementation vary and depend on various factors. This paper is presenting findings and experience gained regarding a method of methane gas utilization for energy production. This method is concerning building bioreactors at the landfill sites, which are already operated. Every bioreactor can be thought of as a process, which is controlled in order to maximize energy production and minimize the methane gas escape into the atmosphere. The bioreactor landfill can represent a number of environmental and cost savings and, at the same time, is able to comply with all legislative issues.

Jan 1, 2005

By David R. Shaddrick

Ore reserves are based on sampling developed by drilling programs. Correct choices concerning the type of drill to be used, depth of drilling, hole orientation and sample spacing are not only critical to the accuracy of the ore reserve but to the cost in time and money of the project. Appropriate interpretation and use of geologic information can significantly enhance the ability to make these decisions effectively. Geologic characteristics of mineralized rock that affect drilling and sample quality include: rock quality, openness, water content, mode of gold occurrence, internal gold distribution and grain of mineralization. Each of these characteristics and sources of data about them are revuewed, then related to the various drill program options. Finally, some procedures for checking the validity and appropriateness of the selected options are reviewed.

Jan 1, 1987

By Thomas J. Martin, James W. Martin, Paul F. Martin

The conveyor belt is the basic building block of a broad range of material handling applications in modern mining systems. The mining plans and site conditions dictate basic system requirements but this is only a part of total design evaluation. The total system in the typical mining situation can encompass all the activities from the excavators at the mining face to the processing plant, site loadout facilities and/or a power plant. The number of alternative configurations which must be evaluated including subsystems and components is limited only by analytical time and creativity. The constraints and issues which must be addressed continue to expand, driven by reliability, environmental impact and cost competitiveness. All of the system requirements must be translated into specifications for costing, final design and construction.

Jan 1, 1993

By R. Mohr

Storm water runoff from mine facilities such as haul roads, waste disposal sites and ore bodies have become recognized as the primary facilities associated with non-point source drainage. Depending on the ore body, facility design and geographical setting, nonpoint source drainage can cause pollution impacts to local surface and ground water resources. Non-point source impacts from surface mine drainage have become an important regulatory issue for the mining industry. Implementing non-point source drainage control plans that prevent impacts to water resources can be accomplished cost-effectively with moderate labor requirements. Design considerations for plan development must incorporate parameters including contributing drainage area size, slope, flow velocity, vegetation characteristics and soil scour velocities. The success of non-point source drainage and erosion stabilization planning is based on implementing control measures that dissect drainage patterns, reduce flow velocities and disperse runoff towards sediment control sites. Interim and long-range drainage control measures should begin during exploration activities. Regulatory legislation addressing non-point source pollution sources was enacted as amendments to the Clean Water Act (CWA) in February 1987. The legislation required states to initiate non-point source pollution control programs.

Jan 1, 1991

By Christopher P. White, John R. Wagner

This paper will discuss the complex and difficult soil conditions encountered in the sinking of 15 shafts of 18m to 27m depth and the excavation and lining of 6700m of 2.74m dia. interceptor sewer on Staten Island, New York. The complex soil profile consists of dense glacial till and sand outwash strata overlying the much older cretaceous sand, silt and clay strata. The tunnel varies from 8m to 14m below the nearby sea level. A significant amount of boulders were anticipated in the till. therefore, a decision was made to excavate the tunnel with a digger shield installing bolted, gasketed concrete segments. The bid documents stated the soils were dewaterable. Several conditions occured in this complex soils matrix which required modifying the planned means and methods including the necessity to use compressed air. The conditions encountered and the equipment used will be described.

Jan 1, 1991

By P. C. Thakur

The history of coal mining in the United States of America and the rest of the world is replete with mine explosions and consequent loss of lives. Serious efforts in the USA to recover methane prior to mining and post mining started about forty years ago. CONSOL Energy Inc. and government agencies, e.g., the erstwhile US Bureau of Mines developed several techniques of methane drainage, such as in-mine horizontal drilling, vertical gob wells, hydrofracing of vertical wells and horizontal drilling from surface. With the current technology, thirty to sixty percent of total methane emissions from a mine can be captured making the mines much safer and more productive. Drained methane is often marketed to defray the cost of methane drainage. This paper is an anthology of these developments and describes how coalbed methane, which used to be a bane, has become a boon for the coalmining industry.

Jan 1, 2003

By J. A. Cervantes

A statistical model for assessing the risk of ground subsidence in abandoned mine areas is presented. The model is based on the relationship that exists between .the frequency and the location-of subsidence events in a given area and the physical conditions of the ground. These conditions can be described by a series of geological, mining, and physical variables. The model suggests the existence of regions in the multidimensional space of variables which are associated .with increases or decreases in the frequency of subsidence events. Regions associated with an increase in the frequency of subsidence events correspond to regions of higher risks, and vice versa. Risk assessment is based on the ability to express the limits of these high and low risk regions in the, space of variables, and on the ability to express the degree of membership of blocks of land within any of these regions. The theoretical framework for the model is extracted, from discriminant analysis. Risk is quantified by the probabilities of membership of blocks of land into any of these regions. Risk maps are produced by displaying membership probabilities in. appropriate contouring levels. The model has been applied in two urban areas where subsidence of the ground has been active in the past. The two areas are Penn Hills, near Pittsburgh, and Scranton/Wilkes-Barre in northeastern Pennsylvania. In this paper, only the results for the Scranton/Wilkes-Barre area are presented. Those for the Penn Hills area have been presented elsewhere (Cervantes, et al, 1990). In the- Scranton/Wilkes-Barre area, geostatistical estimates of variables likely to affect the stability of the ground were made using samples from 53 drillholes. The estimates were made for 2000x2000 ft squared blocks of land covering the study area. Discriminant functions were computed from the estimated variables and used to establish regions for classifying blocks of land into one of these two populations: 1) blocks not likely to have a subsidence event, and ii) blocks likely to have one or more subsidence events. The same, discriminant functions were used to compute membership probabilities for blocks of land to tall within any of these two populations. These probabilities were contoured to produce a risk map. The risk map produced compares well with the location of the subsidence events which have occurred to date in the area.

Jan 1, 1992

By R. Hogg, T. F. Dumm

A simple shape description scheme has been developed which has the specific aim of distinguishing between angular and more rounded particles. The procedure involves fitting a general polygon (usually about 20 sided) to the particle profile. Geometric shape descriptors have been defined based on variations in the angles between adjacent sides and their radial displacement from the particle centroid. A two-parameter shape description, incorporating an angular variabli1ity and an elongation index, has been shown to be clearly consistent with visual observations. A single-parameter angularity index has been shown to be very sensitive to small differences in particle roundness and seems to provide a better description of angularity than other approaches such as signature and fractal analyses. The scheme has been applied to three sets of fine quartz particles produced by different grinding procedures. The results indicate that the technique is capable of distinguishing between angular and re1atively rounded particles and can quantify their specific shape features.

Jan 1, 1991

By Edward R. Torak

The Ohio Coal Testing and Development Research Facility (OCTAD) was commissioned in 1992 by the Ohio Coal Development Office and the Ohio Power Company to support evolving process technologies that will lead to increased environ- mentally sound use of coal. OCTAD is equipped with advanced physical concentration devices and processes capable of beneficiating coal to levels beyond conventional practice. The first task of OCTAD operators was to test the cleanability of the Meigs Creek Seam Coal in advanced circuitry and compare the results to conventional cleaning levels. In testing the seams, OCTAD circuitry was configured to produce middlings on the coarse and intermediate size fractions. These middlings were subsequently crushed to a finer size (28M x 0) and subjected to cleaning in fine heavy-media cyclones and advanced froth flotation circuitry. Nearly thirty-six full-scale production runs at various operating conditions were completed during the campaign. The results of the test program are examined in this paper.

Jan 1, 1995

By Xia Guangxiang, R. Y. Wan, Yang Hanlin, M. C. Fuerstenau

The mechanism and kinetics of pretreatment on pyritic gold concentrate with the catalytic oxidation acid leach (COAL) process were studied in the temperature range of 80-100°C and oxygen pressure range of 230-1013 kPa, with sodium lignosulfonate (SL) and mixed medium of sulfuric acid (11 g/[ ]) and nitric acid (5.5 g/ [ ]). The results show that nitric acid acts as a catalyst, the surfactant changes the hydro-phobicity of resulting elemental sulfur to favor the oxidation of pyrite, and the oxidation-determining step would be the chemical reaction between nitric acid and pyrite. When about 80% of pyrite contained in the concentrate is oxidized, the gold cyanidation extraction exceeds 95 % . The nitric acid in solution can be recycled and used again.

Jan 1, 1993

By Bernhard C. Koch, Richard W. Hutchinson, Bernhard Free

The Tertiary Silverton caldera collapsed asymmetrically to the southwest 27.5 m.y. ago. Resurgent volcanic activity is expressed by a quartz-monzonite stock at the southern caldera margin and by the Red Mountain porphyry stock in the northwest of the caldera which were emplaced at 25 m.y. and 11 m.y. b.p., respectively. The apical Eureka graben formed between 27.5-22.5 m.y. ago and transects the Silverton caldera southwestward. In the northeast it terminates at the 22.5 m.y. Lake City caldera margin. This graben as well as caldera faults provide dominant structural control for base and precious metal deposits. The epithermal gold mineralization of the Gold King mine is proximal to the Red Mountain stock in the north central part of the caldera. Here, west-northwest striking faults related to the collapse of the caldera intersect northeast faults of the Eureka graben. Superimposed upon earlier base metal mineralization at 23 to 22.5 m.y. b.p., the 11 m.y. younger gold metallization was a distinct event at Gold King. Supergene enrichment of the hypogene precious metal assemblage resulted in a metal tenor of up to 3,016 g/t gold and 1,088 g/t silver. The deposit is hosted by quartz-latite tuffs, flows, and flow breccias of the Burns Formation. Veins, up to 5 m wide follow steeply southeast and northwest dipping structures of the Eureka graben. Subsidiary veins up to 2 m wide branch off the main lode and are termed "flat veins" because of their conformable strike but shallow dip of 45' to 50' toward the northwest. Meteoric water-dominated hydrothermal solutions generated by the Red Mountain stock ascended through intensely fractured, ferruginous

Jan 1, 1988

By K. A. McDonald

Hibernia de Mexico SA de CV, based in Durango, Durango, Mexico built and put into operation a 700-t/d (770-stpd) agitated cyanide leach plant in Guanacevi, Durango. Plant construction began in March 1993 and operations began in November 1993. Hibernia de Mexico, a wholly owned subsidiary of Hibernia Holdings, Inc., is a privately held Tucson, AZ-based company. The startup procedures described here deal with Mexico's legal, import-export and finance requirements, and labor and security requirements. The 700 t/d (770 stpd) Guanacevi project is located next to the town of Guanacevi. The project is an agitated cyanide leach plant built to process about 2 Mt (2.2 million st) of flotation tailings over its life. The plant is operated by Servicios de Guanacevi, Asociasion en Participacion. It is owned jointly by Hibernia de Mexico and Metalurgica Guanacevi SA de CV. Legal, importation of equipment and financing For a foreign company to operate in the mining industry in Mexico, it must form a Mexican company. A Mexican company presently must be at least 51 % owned by a Mexican entity. The other 49% may be owned by non-Mexicans.

Jan 1, 1994