Search Documents

By R. A. Paul

The requirements for water inflow control for the Chicago Intercepting Sewer System are stringent. This posed special problems in grouting the bored and conventionally mined tunnels, shafts and chambers of the system. In adapting conventional grouting techniques to the specific problems encountered in the system's pilot project, numerous field procedures were developed. Careful preand post-grout testing and evaluation identified the most efficient and economical of these procedures. As an example of some of the conclusions reached during the project it was found that the mineralized groundwater in the Chicago area tended to reduce the efficiency of the grout holes, thus limiting their useful life. Pressure washing to remove natural fillings was a critical factor in achieving a permanent grout seal. The value of relatively thin lubricating grout mixes was definitely established. Although not an ideal situation, satisfactory results could be obtained by manifold grouting several grout holes simultaneously if done within specific limits of hole groutability, location and numbers. Caulking proved to be a primary controlling factor in achieving acceptable results. To achieve such a high degree of water inflow control requires close supervision by experienced personnel. "Temporary grouting as a construction expedient" produces seepage conditions which are extremely difficult to treat.

Jan 1, 1974

By Robin J. Batterham, Dave J. Robinson

The most significant trend in flotation has been the ever-increasing scale of operations. There is, however, doubt that this ongoing trend is enough to maintain the economics against trends such as falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. We comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 to 20 years, but in the meantime the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation as we know it will change significantly. 

By S. R. Abt, J. D. Nelson, G. M. Smith

An empirical investigation was conducted to formulate a design criteria for predicting the beach profile of hydraulically deposited tailings. Field data were obtained from mining operations producing gold sulfides, silver, molybdenum, copper, platinum, and uranium. Site-specific parameters were collected that included the beach slopes, tailings soil properties, slurry properties, and the slurry distribution system characteristics. Each of the beach profiles were dimensionlessly plotted, and regression expressions were computed. It was determined that either a power expression or exponential expression closely predicted each beach slope. A general power expression and a general exponential ex¬pression were developed resulting in a design criteria. A procedure was formulated to determine which expression, power or exponential, is applicable to any specific site. A slope designation chart was developed as a function of the discharge, the tailings critical tractive shear stress, and the inertial forces exerted by the slurry on the beach.

Jan 1, 1987

By J. Mersch Ward

Homestake Mining Company has identified a significant native sulfur resource at its Cinnabar Canyon prospect in Mono County, California. Elemental sulfur occurs as replacements, fracture coatings and breccia fillings in a thick sequence of Miocene-Pliocene intermediate volcanic rocks. The deposit extends along a northwest trending regional fault and measures approximately 900' in width, at least 1800' in length, and has a thickness in excess of 200'. The deposit lies approximately 150' below the surface and is covered by a silicified cap of volcaniclastic strata. The deposit has been delineated by rotary and core drilling. Utilizing a grade cutoff of 5% elemental sulfur, the delineated deposit has a probablelpossible resource of 16.1 million tons of ore averaging 17.9% elemental sulfur containing 2.57 million long tons sulfur. Assay grades within the resource area range up to 40% sulfur over a 40-foot intercept.

Jan 1, 1992

By Zhu Mingshan, Wu Jiang, Xu Yingqin

A mathematical model to simulate spontaneous combustion of coal in goaf was developed. Under the condition of two-dimensional flaw of air through a bed of uniform mixture of coal, gob, stone etc., the model simulates the temperature rise in the air-and-particle system associated with Arrhenius particle surface reaction. The model is developed as a set of coupled non-linear partial differential equations, which include (1)mass conservation equation for oxygen, (2)energy conservation equation for gas, (3)energy conservation for solid, and (4)velocity equation for gas, that are solved numerically. An elaborate parametric analysis is made of effect of leakage air flux and position of source and sink, parameters relating to the coal accumulating character and the kinetic properties of coal on the tendency to spontaneously combust. In addition, the dynamic process of temperature rise within goaf under several conditions is displayed with picture drawn by computer.

Jan 1, 1991

By E. F. Divers

Adequate ventilation of coal mine working faces is the most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. US Bureau of Mines research has shown that to control respirable dust, you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane, the most effective approach has been to use a blowing brattice, or tubing, and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present. Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan- powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray- fan controls methane on exhaust-ventilated sections.

Jan 1, 1987

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control systems to be used when selecting circuits for washing fine coal (0.5 mm x 0, or 28 mesh x 0, size fraction). However, desliming, declaying, and sizing procedures required for efficient operation normally are not evaluated in sufficient detail, resulting in disappointing system performance. This paper details desliming and de. watering circuit design that is effective based on recent test data. The circuit maintains control of the 0.5 mm x 0 (28 mesh x 0) (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1987

By C. Strachan

This paper presents an evaluation of the tailings dam incidents included in the 1994 US Committee on Large Dams (USCOLD) Committee on Tailings Dams report. Also, comparisons are made to water storage dam incidents from USCOLD reports, as well as to more recent tailings dam incidents. The evaluation results show that tailings dam incidents result from a number of factors, including overtopping, static and seismic instability, seepage and internal erosion, and foundation conditions. The results also show that no particular type of tailings dam or operational condition is more susceptible to incidents. In addition, the results confirm that tailings dams should be located, designed, operated and reclaimed with a thorough knowledge of site conditions, mill operation, site monitoring and tailings characteristics.

Jan 1, 2002

By M. S. J. Leary, M. J. McPherson, O&apos

This paper introduces a computer simulation that extends the use of microcomputer systems for mine ventilation planning. The program was developed as part of an ongoing study to produce a simulation model that would determine the optimum duties of a main fan and a booster fan without requiring the trial-and-error runs that are necessary with currently available programs. To use the new program, the user specifies the location of one main fan and one booster fan, and the minimum required airflows in any number of working places. The computer determines the fan duties that will maintain the required airflows at the lowest operating costs without causing undesired recirculation. The methodology of the program and an example showing how it can be applied are presented.

Jan 1, 1990

By Alain A. Sonntag

This paper presents the most recent developments in KREBS technology directed towards treating higher throughputs, increasing efficiencies and providing further improvement in SX technology with a new concept: the submerged launder. Industrial plants built in the last past few years and using these improvements are described.

Jan 1, 1989

By E. K. Albert

Title IV of the 1977 Surface Mining Control and Reclamation Act (SMCRA) provides for an abandoned mine reclamation fund. This fund, taken from fees collected from operating coal mines, provides capital for the reclamation process. The Act directs the Office of Surface Mining (OSM) to collect the fees based on coal production. Monies from the abandoned mine lands (AML) fund are distributed through two programs. The first provides OSM with capital to use in emergency situations resulting from abandoned mine sites and reclaiming high priority sites in states without established AML programs. The second distributes the money through a state's AML program in the form of grants. To provide for a flexible and customized selection procedure for AML projects, a management information system (MIS) that combines scientific selection procedures is being developed. This system employs objective and subjective methods developed in systems research in recent years. The MIS component is an essential part of any selection process involving large numbers of potential projects. It must contain all the necessary project parameters that can be applied to the selection of projects whether or not they are to be used in the immediate selection criteria. In addition, variable selection criteria will allow ‘what if’ types of inquiries for comparison of differing selections and benefits.

Jan 1, 1990

By Ralph A. MacMillan

Electronic systems introduced for haulage equipment in recent years probably exceed what mine management is prepared to use. Haulpak trucks alone are equipped with General Electric's Statex III drive system controls, Detroit Diesel's DDEC, Cummins' Centry engine management system and the Haulpak Management System (HMS). The future holds promising developments of even more sophisticated electronics that will lead to unmanned truck operation and control. Trolley-assist will finally come into its own due to the importance of environmental issues, as well as the high potential for increased productivity with dramatically lowerfuel consumption. All of these high technology systems do not mean much unless they add value to mining operations. Some of the benefits that can be expected from these systems are reviewed. In the near future, haul truck control and monitoring systems will be fully linked by telemetry to a mine's dispatch system, as well as to its maintenance management information system. The manufacturer and distributor can also be kept in the communications loop, so that they can better serve customer needs. Portable computers will allow technicians to talk to machine systems to quickly locate a problem, look up service information, check what parts are required and electronically order them.

Jan 1, 1994

By R. P. King, M. K. McCarter, K. S. Free

Mine plans typically consider the profits and costs associated with extracting and processing minerals into marketable products. Interrelationships between mine and mill costs are often overlooked during the process of mine plan optimization. A simple and quick method for predicting milling costs for a given block would improve the planning process, especially if the procedure could be incorporated as part of routine ore grade analysis of drill core or cuttings. Incorporating milling costs as part of the mine planning process could improve overall optimization of the mine/mill combination. A method developed by the Utah Comminution Center (UCC) at the University of Utah provides a possible answer to the need for quick and reliable grinding cost estimation (King et al., 1996). Using results from single-particle impact tests, a work index, called the Utah Load Cell Work Index (ULCWI), is calculated. The potential for routine use of the new method is explored by comparing ULCWI values with corresponding Bond Work Index (BWI) values for eight mineral materials (Free, 2000).

Jan 1, 2004

By B. Waterman, R. Collins, V. R. K. Paruchuri, P. Gonzalez, H. Dijkman

"INTRODUCTION Mining and processing of sulfide ore bodies has the potential to solubilize sulfate. Gypsum in the host rock, as well as oxidation of sulfides during milling and processing can solubilize sulfate. Acid rock drainage (ARD) also has the potential to generate waters high in sulfate. Even after treatment of the ARD with lime, the treated water can have sulfate present in gypsum saturation levels. Most mine-sites reuse sulfate impacted water but as a mine nears closure, reuse options may be limited and water treatment becomes an option. Furthermore, sulfate discharge requirements, particularly for anti-degredation narrative standards, can be very strict. Freeport has investigated many new technologies to economically remove sulfate from these types of water. A Dutch company, Paques B.V. developed one of these technologies and it utilized biological reactors to convert sulfate into elemental sulfur in a 2-step process. In 1992 the first industrial reference of the SULFATEQTM technology was commissioned at the Nystar Budel zinc refinery in the Netherlands. PILOT PLANT TECHNOLOGY AND DESCRIPTION As shown in Figure 1, the plant contains several process steps, which can mainly be divided into the following sections: 1. Anaerobic biological system in which sulfate is reduced to hydrogen sulfide by sulfate reducing bacteria. 2. Aerobic biological system in which hydrogen sulfide is oxidized to elemental sulfur by sulfide oxidizing bacteria. 3. Solid/liquid separation in which sulfur, calcium carbonate and biomass solids are separated and dewatered. Sulfate impacted ground water is pumped to the feed water tank through a plate and frame heat exchanger to maintain the solution temperature around 95°F. A custom mix of micronutrients is dosed to the feed tank. This nutrient mixture provides essential elements for the growth of anaerobic and aerobic biomass. Urea is added to the feed tank and provides the required nitrogen source to the biomasses. The pretreated feed water is pumped into the anaerobic reactor. The reactor works on the gas lift principle. Sulfate reducing bacteria utilize hydrogen gas as electron donors and reduce sulfate to hydrogen sulfide. This reaction increases the alkalinity of the solution. Carbon dioxide gas is added in order to control the pH within working range of the reactor. Due to the low solubility of the hydrogen gas, the anaerobic gas mixture is recycled through the system. The gas mixture recycle also provides the gas lift for mixing within the anaerobic reactor."

Jan 1, 2016

By G. D. Trump, F. L. Stanley

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce the cut point and improve separation efficiency. Preliminary economic analysis show that the new circuit provides an attractive payback on capital investment.

Jan 1, 1999

By Y. L. Su

This paper describes a case study where solutions were sought to the truck queuing that occurred at a central processing plant. Ore from three production shafts at Falconbridge Limited's Sudbury Opera¬tions is hauled by three trucking contractors to Strathcona Mill. On return trips, the classified mill tailing is carried back to the mines for backfilling. The ore feeder at the mill handles three times the tonnage designed for and the situation is not expected to improve. Excessive truck queuing and consequent mine production interruptions are therefore of great concern. During the study, stochastic models were formulated and programmed for the IBM/AT personal computer. Basic information sought from the models were truck waiting time and ore production interruptions. The existing system was tested, not only to verify the validity of the models, but also to understand the causes of the problem. Several alternatives were simulated and a simple solution selected for implementation.

Jan 1, 1986

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 2.4-m (96-in.) diam vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subse¬quently, a field test was conducted in a Colorado oil shale mine during which two 2-m (79-in.) diam fans were reversed. The data obtained indicate that reverse performance characteristics depend on the blade angle and the hub-to-tip ratio. The quantity in the reverse mode ranged from 30% to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1987

By A. F. Stewart

Slope design in an open pit mine includes the determination of a number of parameters, including bench height, bench face angle and berm width. By way of a case history of two highwall slopes (160m and 220m high) excavated in dipping strata in an operating coal mine, this paper illustrates the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in essentially the same lithologic and structural environment, with the main differences between the slopes being the angle at which the bench faces were excavated and the excavating methods that were employed. In addition to describing the instability that occurred on one of the pit walls, relevant aspects of the engineering geology, slope design and excavation procedures are described.

Jan 1, 1998

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987

By M. C. Rockwell, G. F. T. Lay

Promising placer gold exploration sites offshore Lunenburg County are drowned pre- and post-glacial river channels and auriferous glacial tills. Gold values up to 5.67 9/m3 have been encountered in the vicinity of the Ovens Peninsula offshore Lunenburg County. Moderate gold values associated with notable amounts of heavy minerals were reported from various other exploration sites in this area. This paper highlights the major geological and gemorphological features for placer gold depositions in southern Nova Scotia. The past to present gold exploration activities nearshore and offshore Lunenburg County are summarized and potential areas for placer gold identified.

Jan 1, 1988