Search Documents

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001

By I. G. Ediz, D. W. Dixon, W. M. Fidler

In this paper a new method for the arresting of tunnel explosions is presented. In the proposed technique, the on coming explosion is detected by a pressure sensitive device by a pre-determined rise in static pressure. The sensor then triggers a mechanism which causes the explosion door to be closed in a specially constructed concrete barrier zone. The doors are of a special construction and consist of perforated steel plates that allow part of the blast wave to be transmitted but do not allow the passage of the flame. A number of design parameters have been identified, including: the likely amplitudes of the transmitted/reflected pressure waves that would govern the explosion door pressure loading; thickness of the perforated steel packages; perforation dimensions; heat transfer across the door and other factors.

Jan 1, 1995

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By Michel David

Once a mineralized body has been delineated, drilled and estimated from surface samples, it often happens that before the final go-no-go decision is taken, an underground sampling program is decided, very often via a ramp which hopefully will be later used to extract the ore. The cost of such a program can be close to a million dollars. On other occasions, when a property changes hands and is reexamined maybe 20 years after the original drilling program, a "check sampling" program is carefully, designed to make "sure" that the old assays are "correct". One may fear poor sampling practice in old days, or deliberate highgrading by promoters. Again one may be talking of resampling cost which may be in the six-figures range. Other similar situations include the drilling of a few large diameter holes to ascertain the validity of a majority of small diameter drill holes, or auger drilling, or back-rimming. In uranium checking radiometric information is also a problem related to the above ones.

Jan 1, 1979

By R. A. Jankowski

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers using six different filter panel designs at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least-dense filter was as much as 33 % lower than the collection efficiency of the most-dense filter. At the low operating velocity, the least-dense filter allowed more than 40% of the respirable silica dust in the scrubber intake air to pass through the unit and back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency regardless of the filter panel tested The density of the filter panels also impacted the quantity of air moved through the scrubber, with higher-density filters reducing scrubber airflow. For each filter, the relationship between dust-collection efficiency and air-moving capacity must be considered to determine the overall effectiveness for each mine application.

Jan 1, 2000

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By Mario Eduardo Rossi

The Universal Kriging (UK) and the Ordinary Kriging (OK) systems of equations are variations of the well-known system of Normal Equations. They differ only by the number of constraints present in the system. The dual version of these sytems enables one to interpret kriging as the fitting, of an interpolation surface, whose components are a series of variogram functions plus a polynomial trend model. This trend model should account for any systematic decrease or increase of the variable over the study area. It is shown that modeling the trend is useful only when the locations being estimated are beyond the range of influence of neighboring data (extrapolation cases). A case study based on a public-domain coal data set is presented. The variable described (seam thickness) shows an actual trend of increasing data values towards the NW corner of the region considered. UK and OK are used to estimate coal thickness at locations within sample data range (interpolation cases). The UK algorithm that includes a model for the trend does not improve the estimation when compared to the simpler OK algorithm with no trend model. Thus, in interpolation situations, the simpler OK algorithm is recommended.

Jan 1, 1989

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By John M. Wootten

The development of new coal markets is -t upon the ability to utilize coal in an environmentally acceptable and economically viable fashion. Foremost in the concerns about coal utilization is the impact its combustion has on air pollution. Concerns over environmental issues, such as acid rain, are currently one of the major impediments to the development of new coal markets. The Department of Energy and the Synthetic Fuels Corporation are addressing certain aspects of the development of new technologies for the utilization of coal. However, at the present time, there is a void in the new technology development process. That void is the step from proof- of-concept to commercial demonstration. Congress has established the Clean Coal Technology Fund at a level of $750 million to fill this void. The Department of Energy, in a solicitation of interest, received over 175 proposals for commercial demonstrations of clean coal technologies. A review of these solicitations indicates that $1.2 billion worth of research could be accomplished with a federal cost sharing of $425 million or 35 percent of the total. Industry has indicated, through this response, its willingness to invest its limited funds on projects it feels have the greatest potential for the clean use of coal. What must now occur is that Congress must appropriate the monies from the fund to initiate the commercialization of these clean coal techno1ogies.

Jan 1, 1986

By E. J. Beckman, R. M. Enick, C. Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic platinum group metal complexes from an aqueous phase. However, because conventional extractant-metal complexes are not soluble in liquid carbon dioxide, this can be achieved only if highly carbon dioxide-soluble extractants are developed. For example, trioctylamine-gold chloride is not soluble in liquid carbon dioxide, although trioctylamine is CO2 soluble. The novel CO2-soluble extractants presented in this paper have a CO2-philic fluorinated tail to enhance solubility and a conventional amine head group for extraction of metals. Both the extractant and the extractant-metal complex are soluble at ambient temperature at pressures from 7 to 35 MPa. Efficiency factors as high as 2.23 have been measured using 1,1,2-trichlorotrifluoroethane (TCTFE), a low pressure screening liquid for carbon dioxide, indicating that these compounds will strongly bind the metal chloride. For example, 84% of Pt-chloride was extracted into TCTFE using a 3.5:1 ratio of a double¬tailed fluoroalkyl amine extractant: metal chloride. An 88% recovery of Pt-chloride into high-pressure liquid carbon dioxide was achieved using the same extractant at a 3.5:1 ratio. Therefore, it appears possible to replace organic solvents with liquid carbon dioxide during the extraction of platinum chlorides if highly carbon dioxide-soluble extractants agents are employed.

Jan 1, 2002

By Vernon R. Degner

The past two decades has seen the application of the mechanical flotation machine, originally developed primarily for metal1iferous ore beneficiation, increasingly applied to cleaning coal in the 28x0 T. Mesh size range. Internal cell hydrodynamic studies of mechanical flotation machines of all sizes, as well as computer aided modeling studies of flotation kinetics has, within the last five years, established a basis for optimizing coal flotation circuit design and machine operation, and has a1 so pointed a way toward improvements in mechanical flotation machine design for the future. Consideration of the trend toward increased fines produced by current mining techniques, as well as the environmental need for a progressively cleaner product, lends support to basing the design of the mechanical coal flotation machine of the future on finer feed; below 100 microns in size. Future types of mechanical flotation machines, which may satisfy the fine coal cleaning requirements for a significant improvement in product grade while maintaining the combustible recovery levels of current technology, are discussed.

Jan 1, 1988

By D. E. Ranta, John G. Stone

One of the steps in an ore reserve estimate is customarily a rigorous calculation of the in situ grade of the orebody itself. The result of this calculation is usually reduced by some purely arbitrary factor to force the calculation to agree with the observed grade of ore actually mined. The failure of the calculation to realistically depict the grade of ore actually extracted is in many instances not the result of either an incorrect calculation procedure or of sloppy mining practice, but is a direct consequence of unsuspected irregularities in the contact between the orebody and the surrounding wall rock. A pattern of holes spaced at 1.5-3.Om foot intervals, drilled as part of a pre-development program, will often reveal that a presumed "regular' ore/waste contact is, in fact, so highly irregular that it will be next to impossible to separate ore from waste during mining. In such an instance, 'fingers' of waste projecting into the mining block will substitute for equal volumes of ore left outside the mining limits. As a result, the grade of material actually mined will be less than the grade envisioned for the orebody. The volume of waste substituting for ore in the mining block is about 0.4X, where X = the average error in projecting the ore/waste contact between alternate holes in the test pattern, and is expressed in units of volume per unit of area of the contact surface.

Jan 1, 1992

By Kenneth L. Clifford

We have heard a lot during the recession about the mining industry now competing in a world market for sales of such commodities as copper, lead, zinc, molybdenum, iron ore, and phosphate. If the US mining industry is to survive, do we not have to reduce direct operating costs to a minimum? How significant is labor cost compared to consumables, electricity, fuel, maintenance, materials, and transportation? Ore grade is ultimately the dominant factor; but can we offset its dominance by improving productivity? Is the US mining industry perhaps only 25-30% as productive as it might be? What prevents the industry from being more productive? Can we retrofit older plants to be more productive or does it take a new plant with the largest equipment available for each unit operation? Present Productivity A copper industry study a few years ago covering 13 US copper concentrators ranging from about 10-45 kt/d (11,000-50,000 stpd) showed that productivity did not vary with capacity above 18 kt/d (20,000 stpd). Operating productivity varied significantly, however, from about 180-635 t/d (200-700 stpd) per operating hourly worker in most units, but one operation had 900 kt/d (1,000 stpd). Concentrators with more than 545 t/d (600 stpd) per hourly worker were in the 23 kt/d (25,000 stpd) or more category. Maintenance productivity covered about the same range, but most concentrators were in the 270¬635 t/d (300-700 stpd) per hourly maintenance worker. Again, one company stood well above others by exceeding 1 kt/d (1,100 stpd). Total hourly productivity ranged from 125-280 t/d (140-310 stpd) per hourly worker for most concentrators. The company with the most productive operation, however, was above 455 t/d (500 stpd). Salaried worker productivity for most operations was in the 725 t/d to 1.2 kt/d (800-1,300 stpd) per salaried worker range. The best operation was 2.2 kt/d (2,400 stpd). The end result is, of course, tons per day per total personnel. Most operations fell in the 110-220 t/d (120-240 stpd) range with the best operation at 400 t/d (440 stpd). This is the productivity definition that is most directly related to unit costs. Many of these operations have made some productivity progress

Jan 11, 1983

By P. F. Ziemkiewicz

This project evaluated the performance of nine passive treatment methods by studying 137 treatment units in eight eastern states. Performance was normalized according to construction cost, projected service life and tons of acid load treated. Results were dimensioned as $/tons of acid load treated/year. These costs were then compared to those of chemical treatment. Sites that achieved acid load reductions at costs below those of chemical treatment were considered successful. In addition to evaluating the performance of the treatment methods, this paper describes the various passive treatment systems, their applications and performance data for individual treatment units.

Jan 1, 2003

By Norman Miskelly

Role of CRIRSCO CRIRSCO has an advisory and hopefully influential role in International Mineral Resource/Reserve Reporting Standards CRIRSCO also has a broad educational role CRIRSCO does NOT have a negotiating role CRIRSCO does NOT have a regulatory role

Jan 1, 2003

By Liu Hongkang, M. J. Virnig, Yang Xianwan, Zhu Yun

A new technology for recovery of gold from loaded carbon developed by Kunming Institute of Technology is introduced. The principle, production practice and results are described.

Jan 1, 1993

By C. DeW. Van Siclen

A simple mathematical description of the settling behavior of monosized particle suspensions is derived by consideration of the physical processes involved, and applied to data recently published in this journal.

Jan 1, 1995

By Lennart Mukka

This paper describes the experiences from construction of a new ventilation system in LKABs Kiruna Mine in Sweden as well as the choice of the method for air flow regulation with concern of life cycle cost and the description of the foundation design. The evaluation of the performance test will be presented.

Jan 1, 1997

By N. Magdalinovic

This paper analyzes the basic elements important for sustainable development in the sphere of metal mineral raw materials and offers one of the possible ways of defining the index of sustainable development.

Jan 1, 2007