Search Documents

By David G. Abbott, Frank Coluccio

This paper will discuss the construction of nearly 165 m (540 ft) of 3.5. m (138 in) o.d. reinforced concrete pipe to replace an existing utilidor under the Duwamish River in Seattle, Wash. The project required that two 27.4 m (90 ft) deep shafts be installed for use as jacking and reception shafts during the tunneling operation, and permanent vaults once completed. Soil conditions to be excavated consisted of soft saturated sand and silt with a 21.3 m (70 ft) water head. This required the shafts to be constructed using ground freezing techniques and the tunnel installed by pipe jacking, using a Mechanical Earth Pressure Counter Balance (MEPCB) slurry shield. The original utilidor was constructed between 1924 and 1925, and has since been deliberately flooded because it is considered to be structurally unsound.

Jan 1, 1995

Rinker Materials Corporation (Rinker) operates construction aggregate operations in 15 states across the US. Thirteen of those operations are located in Florida, where Rinker produced approximately 40 million tons of aggregates in 2002. Because the deposits being mined in Florida are shallow sedimentary deposits of limestone and natural sand, with the deepest being approximately 75 feet deep, abundant acreage is mined annually. Rinker mines about 300 acres/year in Florida alone, and because there are so many wetlands and complete avoidance is nearly impossible, there are also wetland impacts. Thus, there is ample need for reclamation and mitigation, which presents an opportunity to involve local school groups with the planting and monitoring of these various projects. Rinker has successfully worked with a half dozen or so schools on these projects, involving students from grade school through college, with surprising success and outstanding results.

Jan 1, 2004

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By R. W. Smith, K. A. Altman

The use of activated alumina for the removal of selenium from heap leach detoxification solutions was studied at a laboratory scale. Three different aluminas were studied, one unmodified and two chemically modified to function better in a basic pH range. The best performer, Discovery Chemicals DD-6, readily accumulated selenium oxyanions. Furthermore, it could be stripped of selenium and several metals by a mild caustic solution (pH 11.5 – 12.0) and regenerated for further use. Tests using - 600 µm, + 300 µm (28 x 48 mesh) material indicated that 96 % could be removed from solution and using – 1.18mm, + 600 µm (14 x 28 mesh) material 91 % could be removed. However, soluble silica can accumulate on the activated alumina and subsequently interfere with its regeneration and should be removed from the detox solution prior to use of the adsorbent.

Jan 1, 2003

By F. Duan, W. G. Pariseau, C. S. Schmuck

Three dimensional comparisons between calculated and measured displacements in the hanging wall of a rock mechanics study region at the Homestake Mine show correlation coefficients of 0.7 or higher. Two and three dimensional back analysis of the data lead to different scale factors for determining rock mass strengths and moduli from laboratory values and seemingly to different rock mass properties. A simple analytic model suggests that indeed not only are there two independent scale factors, one for strength and one for moduli, but that there is a logical relationship between the scale factors obtained from two and three dimensional back analyses of the same mine measurements. The three dimensional modeling procedure implemented in the finite element code UTAH3 thus seems to have a realistic potential for investigating underground hardrock mine questions not amenable to two dimensional analysis.

Jan 1, 1987

By R. J. Hickson

From 1993 through 1999, Cyprus Amax Minerals successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized and an environmental issue was appropriately remediated. The projects stretched over three continents: from arctic Russia to the Atacama Desert, from sea level to an elevation of 4,900 m (16,00Oft), from city suburbs to remote wilderness and from a low of US$130 million to more than US$ 1billion. The operations included open-pit and underground mines, mill and leach facilities and involved gold, copper, molybdenum and coal. The diversity of these projects inspired Cyprus Amax to create a "best-practices” project-management protocol to steer corporate expansion in the new millennium. This paper summarizes these best practices, while highlighting the project-management pirfalls to avoid.

Jan 1, 2000

Since the Rio Declaration on Environment and Development in 1992 in Rio de Janeiro and the publication of the agenda 21, the concept of Sustainable Development has become one of the major issues for governmental politics, societal developments and entrepreneurial policies. Current projects that deal with Sustainable Development in the mineral raw materials sector mainly focus on large-scale mining operations - especially for open pit mining - or on artisanal small scale mining. Artisanal small scale mining is in this connexion characterised as non-mechanized and mostly illegal mining activities. The number of workers is mostly far below 20. However, until now there exist no assessments or analyses with respect to the actual or potential contribution of industrial small scale mining to sustainable development. Industrial small scale mining refers to high technology or highly mechanized/automated extraction of small, high-grade deposits that due to their small size ? in combination with geological, depth and other constraints ? are not economically exploitable with large-scale mining operations. The Institute of Mining Engineering I and the Institute for Processing of Mineral Raw Materials at the RWTH Aachen University in Germany is currently conducting a research project financed by the German Research Foundation in order to investigate this issue. In the course of this project the sustainability of industrial small scale mining will be assessed. Therefore sustainability indicators, an assessment system and recommendations as well as options for actions and policies will be developed, in order to evaluate current industrial small scale mining activities as well as the potential for future developments in industrial small scale mining, both from a technological as well as from the point of view of sustainability, considering economical, social and environmental chances and risks.

Jan 1, 2007

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By J. L. Weeks

Discussion by J.L. Weeks Discussion I wish to comment on Kissell and Sacks's paper "Inaccuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines." It is well established in industrial hygiene that area sampling is not an accurate measure of personal exposure. To measure personal exposure, one must use a personal sampler. Kissell and Sacks, using data from coal mining, reached the same conclusion. This is the right answer but it is the wrong question. This issue arises because the machine-mounted respirable dust continuous monitor (MMRDCM) is being considered to monitor coal-miners' exposure to respirable dust. This device may be mounted on a continuous mining machine, and it would take a modified area sample. I refer to it as "modified" because a mining machine is not really a fixed location, as is the typical area sample. The concern with whether this machine would provide an accurate estimate of the machine-operator's exposure, however, overlooks important features of the MMRDCM. Specifically, it displays dust concentration as it occurs and at the place where it is needed, not 10 days later, as is the case with the current system. Used in this way, it allows for timely intervention to control exposure to dust and it leads to greater first-hand knowledge of specific conditions and mining practices that result in excess exposure. If one knows the dust level is excessive at the time the dust is being generated, it is possible to use known and effective methods of dust control to reduce exposure. By measuring again, one can determine whether control methods have worked. This is a generic procedure followed in any industrial process: measure, adjust and measure again. It leads to more effective and more efficient dust control and is preferred to taking a sample, waiting 10 days for the results and then trying to apply that information to a situation that no longer exists. The MMRDCM also records the dust level automatically, and it runs continuously, making it harder to tamper with. Dust monitoring in underground coal mines has been corrupted by some operators having submitted fraudulent samples (and being convicted on criminal charges because of it), weakening the credibility of the current system. The MMRDCM is, in part, a response to this corruption, and an effort to focus attention on dust levels and dust controls rather than on the perpetrators of fraud. Use of the MMRDCM is an evolutionary change from the current system. With the current system, one takes a personal sample of exposure of the "designated occupation" (DO, defined at 30 CFR 70.2 (f)), the occupation regularly exposed to the highest level of dust on a section. Typically, on sections using continuous mining machines, this is the mining-machine operator. The rationale behind DO sampling rests on some of the findings that Kissell and Sacks report. They reviewed several studies that showed that dust concentration varies with location on a mining section and that there is a concentration gradient with the highest concentration occurring closest to the face. The logic behind DO sampling strategy is that if the dust concentration at the place where it is highest is below the exposure limit, then concentration elsewhere on the section is also below the limit. In this way, one will have achieved the objective or keeping dust concentration below the exposure limit for all miners on the section by measuring the exposure of only one miner. The

Jan 1, 2003

By Nellie E. Guernsey, Louis J. Sousa, Alfred Weiss, Nickolas J. Themelis

Over the past decade, numerous factors have led US copper firms to face increasingly severe competition from low cost foreign producers. As a result, greater attention is being devoted to developing and implementing new technology that can reduce costs and maintain the competitive position of domestic firms while simultaneously meeting environmental requirements. To obtain a better understanding of the likelihood of the development, adoption, and use of innovative copper technologies in the future, the Bureau of Mines contracted with Mineral Systems Inc. of Stamford, CT, to undertake a systematic survey of technological experts in industry, government, and the academic community. According to the survey, major developments in exploration over the next 25 years are likely to be in technologies that facilitate analysis and interpretation of deposit data rather than those that enable the collection of additional data. Most new copper mining and beneficiation technologies are likely to represent evolutionary extensions of existing systems with a notable increase expected in the application of information systems technologies and computer control methods. A possible movement towards increased usage of continuous mining systems in copper was also noted. Experts indicated that several copper smelters are under consideration for extensive renovation and, as a result, flash smelting technology is expected to become much more widely used in the US. A gradual movement toward continuous smelting methods was also forecast. In copper refining, the major technological change expected is the gradual automation of various refinery operations. Finally, though increased usage is expected, in situ solution mining and hydrometallurgical processing of sulfide ores are not expected to become widespread over the forecast time horizon. This first article in a two-part series describes the survey method chosen and the technological innovations selected for eval¬uation. Also discussed are the assessment panels, background scenarios, critical events, and diffusion forecasts. Next month, part two will address technology forecasts resulting from the study. Featured are discussions on future copper exploration, mining, beneficiation, smelting, refining, and recycling. A cost/benefit analysis will also be included. Methodology Selection of Assessment Method To develop a consensus forecast of technological change in the copper industry, a technique for systematically polling subjective opinions of experts was required. After conducting a literature survey and some preliminary testing, the direct probability assessment method was selected. With this assessment method experts are asked to express in quantitative terms their judgment of the probability that a specified event will occur, usually over a series of time frames. The method was chosen because the experts were observed to be more comfortable with this approach during the testing period, and the results of this process effectively satisfied the assessment objective. The experts generally could provide more precise estimates of the timing of future events using this technique because it was the least cumbersome of the assessment methods tested. Identification, Selection, and Description of the Technologies The initial list (Table 1) of innovative copper technologies assessed in the study was developed from two principal sources: knowledge and expertise of the study team and a review of relevant technical literature. From this list of 47 potential technologies, 10 were selected for detailed assessment. Table 2 lists 35 technologies that were subsequently identified in the first series of assessments. Twelve technologies from this list were also selected for detailed evaluation in a second assessment round. Criteria used for the final selection of technologies for detailed assessment specified that: • The expected impact of each technology on copper supply (i.e.,

Jan 9, 1983

By Brian Hester

Many Third World African countries are well-endowed with minerals - especially gold and diamonds - while only a few have important base metal deposits. For decades since colonial rule, political and economic conditions discouraged interest by Western capital. Influence from Soviet Bloc countries, however, has declined with the move toward multi-party rule. And the left wing orientation, once widely favored by Third World African countries, has almost disappeared. With International Monetary Fund (IMF) encouragement, these Third World African countries now encourage representational government and solicit western finance to expand their industries. Mining is especially encouraged. The North American mining industry is following the same trail as other capital intensive industries and looking abroad for opportunities. The Prospectors and Developers Association of Canada released figures that show exploration expenditures in that country were halved between 1987 and 1990. Figures for the United States are not so easily found but every indication points to a downward trend. While total annual expenditures on US exploration by corporations as a group are either declining or remaining constant, expenditures away from North America is increasing. Gold exploration expenditures in 1991 by the major companies tracked by Minerals Economics Group were less in the United States than for Latin America and the Southwest Pacific combined. The same study showed as much was spent in the Republic of South Africa and "Other" areas combined as in the United States. Expenditures by major corporations in these "Other" areas amount to only 5.2% of their total budget. Third World Africa is a major component of these "Other" areas.

Jan 1, 1993

By James N. Prudden

Measurable physical characteristics of placer deposits include geological, geomorphological, sedimentological and mineralogical features which produce the complimentary ingredients with which one can formulate an economic evaluation of these complicated deposits within the confines of a well established geological model. Heavy mineral suite composition and character will change downstream from the provenance area and will compliment the related depositional environment. Careful attention to gold particle characterization during the exploration phase can indicate new source additions, enhance deposit evaluation methods and greatly assist in maximizing metallurgical efficiencies. Failure to recognize and measure these important features very frequently leads to frustrated and unrewarding placer evaluation goals. Increased general acceptance of sedimentology in the gological appraisal of ore bodies has progressed into the science of clastic sedimentalogy using measurable parameters to evaluate minable units. This branch of geology has developed as a tool in locating, defining, and mining alluvial concentrations of valuable heavy minerals. The repeatedly successful application of this valuable tool in conjunction with other classical geological methods can be directly related to the development of a geological model which formulates the distribution of detrital gold. This use of multiple geological techniques permits the transfer of routinely derived data to management. Standardized nomenclature permits the transmission of uniform information thereby promoting credible property evaluation. This approach enables organizations to critically assess large numbers of potential mining targets for definitive feasibility studies. Sedimentology must play an integral role in the evaluation of any alluvial deposit. The sampling problems associated with particulate gold are well known and frequently cause perplexing evaluation problems. Consequently, properly directed and executed

Jan 1, 1987

By Robert W. Wheeler, Richard G. Ames, Robert B. Reger

Introduction The use of diesel engines as an alternate power source in US underground coal mines has been a controversial step towards more efficent mining practices. Three areas of potential benefit are foreseen. First, diesel-powered mining equipment is believed to be more efficient, resulting in less occupational risk for any given amount of production. Second, diesels are believed to pose fewer intrinsic hazards, especially those related to fires and ignition of combustibles. Finally, several other health and safety advantages are foreseen for diesel units. Each of these issues will be discussed separately. Diesel Efficiency Proponents of the use of underground diesel-powered mining equipment point to increased production efficiency due to greater maneuverability, speed, power, and payload (Bradbury, 1973; Jorgensen, 1982; Ogden, 1978; Wenberg, 1979; Olsen, 1980). Units most suitable for diesel power include LHD vehicles, shuttle cars, personnel carriers, and maintenance vehicles. Estimates of increased efficiency vary from 60%-300% and more (Wenberg, 1979). Increased diesel mining efficiency is usually viewed as making it practical to mine lower grade seams. Diesel units can also operate over a wider range of floor pitches and distances than electrically-powered units, thus allowing mining of seams with special mining problems (Olsen, 1980). Diesel application is not a universal substitute for electrical power. For example, continuous miners are unlikely diesel candidates. Reduced Intrinsic Hazards Proponents of diesel use have pointed to the increased safety potential due to a reduction in electrocutions, arcs, burns, underground cable fires, and methane ignition (Ogden, 1978). Diesel units are frequently employed in maintenance activities for lifting and moving, and for coal cleanup. Thus the case is made that diesel use, by making powered operations more conveniently available, reduces the incidence of lower back injuries and related causes for days lost due to disability (Olsen, 1980). Several other issues relating to diesel safety have also been suggested. Diesel units can continue operation even during power outages allowing, for example, personnel evacuation. The maneuverability of diesel units make them particularly attractive in difficult physical conditions, such as long haulage from the face to the belt and in areas where water is deep. The case for diesel use focuses heavily on the potential for a "per worker" reduction in accidents, or a reduction in the severity of accidents. Since accidents are a major part of the health impact of mining, a reduction in accidents and resulting injuries would make a major contribution to the health of coal miners. Opposition to Diesel Use Opposition to the use of underground diesel mining equipment in the US seems to have started with the United Mine Workers of America. Some opposition to US diesel use has been based on a widely publicized 1976 letter from NIOSH to Mine Enforcement and Safety Administration administrator Robert Barrett (NIOSH, 1982). In essence, this letter warned that while insufficient evidence existed as to diesel effects on underground coal miners, NIOSH had concerns based on prior knowledge of separate diesel exhaust constituents and the potential for interaction between these constituents and coal mine dust. Current opposition to underground diesel use has focused on respiratory health effects related to diesel emissions, particularly nitrogen dioxide (NO,), carbon monoxide (CO), and particulate content (Barrett, 1982). Through

Jan 4, 1983

A roof rating system has been devel¬oped for upper seam damage prediction during mul¬ti-seam mining based on structural and geologic conditions in the upper seam. Two primary consid¬erations -geologic and spatial - form the basis of the classification system. It includes factors commonly found in geomechanics classification systems as well as factors which are peculiar to multi-seam mining, such as those which define the two adjacent seams and the innerburden. This rating system has been applied to numerous case studies to form empirical relationships for quan-titatively predicting potential upper seam damage based on anticipated subsidence and strain values and vertical movements.

Jan 1, 1988

By Donald R. East

The impacts of the economic storage or disposal of mill tailing wastes are becoming more important to the mining industry as environmental regulations become more demanding. Mill tailings have long been considered the stepchild of the extraction process and have not, until recent years, been treated as a separate entity of the mining and milling process with distinct and complex physical and chemical characteristics. As a waste product, the economic value of mill tailing is usually very small whilst economic and the environmental liabilities can significant. be Disposal of tailing is commonly identified as the single most important source of environmental impact for many mining projects.

Jan 1, 1990

By Richard W. Jolk

A pollution control equipment exemption which reduces the fair and equitable taxable value of a mine property is allowed under Nevada Revised Statute (NRS) 361.077 and must be filed in accordance with the filing requirements of NRS 361.155. USMX Nevada Operations annually saves a substantial amount of State property tax dollars by taking advantage of this tax exemption. The State documents received by USMX and the documents filed by USMX are reviewed in this paper. The application filed by USMX exhibits the format and detail used to obtain this tax exemption and the extent to which environmental control equipment may be claimed.

Jan 1, 1993

By G. L. Mowrey

One critical element of the US Bureau of Mimes computer- assisted mining research program is the development of a reliable coal interface detection (CID) system. Several promising CID concepts currently being investigated by the Bureau include natural gamma radiation (NGR), vibration and passive infrared. To help establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (immediate roof and floor) are being collected from selected major coal seams in the US and are being analyzed in terms of NGR and other geophysical measurements. This paper provides a brief overview of the Bureau's work in these CID areas.

Jan 1, 1992

By Jon Y. Kaneshiro, Donald W. Scapuzzi

The primary purpose of the Prototype Installation Facility (PIF) for the Superconducting Super Collider (SSC) in this conceptual design was to test the magnets and other physics equipment. PIF was located in the northwest quadrant of the SSC 54 mile (87 km) main ring and consists of the first segment of tunnels, approximately 17,060 lineal feet (5.2 km) of 12 foot inner-diameter (ID) (3.7 m) tunnel, three 250 ± foot (60 m) deep shafts, connecting tunnels, and associated niches and alcoves. PIF would be the first portion of the main ring collider tunnel to be constructed. The geology, underground excavation conditions, underground facilities, and contractual considerations are discussed.

Jan 1, 1991

By J. Engel

The talc deposit in Gemerská Poloma lies 350 to 400 m under the surface; the whole deposit is located at the highest-level drinking-water-source protection zone, therefore, opening in this mining area (a well, a ramp) requires higher investment, operational and water protection costs. The adit, outside the mining area, with a length of 4200 m, rising with a gradient of 3? and a diameter of 10.3 m2, allows free passage/runoff of mining-water through the adit, and guarantees low costs for transporting produced material and equipment. This solution is in total less demanding from both investment and operational point of view.

Jan 1, 2007

By John Turney, John Gathje, Donald Gale

The Eskay Creek deposit, located in northern British Columbia, is a high-grade gold/silver ore associated with complex polymetallic sulfides. Process development began in 1989 and continued through 1993. Because of the refractory nature of the ore, options including roasting and smelting were investigated. The selected process of pressure oxidation was the basis for basic engineering design until a re-evaluation of economics and risk indicated a preference for toll smelting. Although well proven in many industrial applications, pressure oxidation of the Eskay Creek ore dictated several innovations to solve problems associated with silver jarosite formation, preg-robbing, and high soluble copper and zinc concentrations.

Jan 1, 1995