Search Documents

By S. F. Hillis, J. E. Rourke, K. A. Szalay, O&apos

INTRODUCTION For the past 25 years, tunnel support requirements have frequently been determined, at least in North American practice, by classifying the rock according to the system proposed by Terzaghi (1), using one or more of the 8 Rock Conditions which he defined, the rock load then being selected within the range given for each Condition. However, there is a lack of published data comparing Terzaghi loads with actual measured rock loads, and it would appear that the degree of conservatism, or otherwise, of the Terzaghi approach is very often unknown. Excavation of 4 large diameter tunnels at the Tarbela Dam Project in Pakistan afforded an opportunity to compare Terzaghi and measured loads, through instrumentation of the steel ribs installed for temporary support, and by classification of the geology exposed during the tunnelling operations. In addition, the deformation of the rock surrounding the tunnels was monitored during excavation by means of borehole extensometers installed prior to the start of tunnelling. This paper describes the tunnel instrumentation and the results obtained therefrom, and relates these results to the Terzaghi load coefficients. It also discusses the effects of the methods of excavating the tunnels on the rock loads and rock deformations. PROJECT DESCRIPTION The Tarbela Dam Project is located on the Indus River in

Jan 1, 1974

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By Peter J. Stewart

My first experience with carbon reactivation in the gold industry was at Whim Creek, Meekatharra some 15 years ago. Very little was known, in fact, carbon reactivation kilns in the gold room were a complete mystery. Ten years ago at conferences such as this the mystery was more as to why field kilns would not reproduce activities achieved in the laboratory. A carbon reactivation kiln manufac­turer was thought to be brave or stupid to speak at a venue such as this. Reactivation kiln design has improved dramatically in the past 10 years and with a few exceptions, most kilns operate well. May I suggest that now, the focus is on plant practice rather than kiln design, and that the basics of plant practice as it relates to carbon activity needs revisiting. As metallurgists like to talk on engineering, accountants on the Economy and vice versa, my presentation on Carbon Reactivation will focus on plant design and operation as it effects carbon reactivation. There have been some excellent papers published over the past 15 years on the basics of carbon reactivation in relation to gold processingl,2,}. Taken that kilns operate and are effective to a greater or lesser degree, plant design and operating practise have an enormous bearing on carbon activity, solution tail, carbon loss and other cost items. This presentation will not argue the merits of equipment used for the thermal reactivation of organically fouled carbon, questions on this subject are welcome over a drink after this session.

Jan 1, 1995

By A. L. Putz, G. Ladouceur, A. R. Laplante

A laboratory centrifugal concentrator was used to evaluate two gravity circuit configurations treating a flash flotation concentrate at a Canadian gold mill. The Initial circuit consisted of a 76 cm (30 Inch) plant Knelson Concentrator (PKC) for coarse gold removal. Later, a hydroseparator and spiral were Installed, with the hydroseparator underflow feeding the spiral and the spiral tailings plus hydroseparator overfiow reporting to a 51 cm (20 Inch) PKC. Gold recovery In the 76 cm PKC averaged 45%. Gold was recovered consistently In all size fractions greater than 38 µm, where recovery dropped to 22% for the -38 µm material. Changing the circuit to Include the hydroseparator and spiral decreased the Knelson unit recovery to less than 17%. The decrease was attributed to the spiral which recovered much of the free gold ahead of the Knelson and to changes In the mill feed (free gold portions were finer and less abundant). The spiral demonstrated erratic behaviour although It still recovered significant coarse gold (+75 µm) yielding unit recoveries of 18-44%. Although mechanical difficulties were experienced with the 76 cm PKC, Its performance was superior to that of the hydroseparator, spiral and 51 cm PKC configuration. Much of the gold In the ball mill recirculating load was found to be too coarse for significant recovery In the flash flotation cell and should be recovered by gravity from the cyclone underflow or ball mill discharge. The LKC proved to be a successful device to evaluate gravity recoverable gold content. Dilution of test samples with silica further enhanced this methodology.

Jan 1, 1993

By Mark L. Bricker

The Jim Bridger Coal Mine, operated by Bridger Coal Co., is located in Sweetwater County, WY about 56 km (35 miles) northeast of Rock Springs. Bridger Coal is a joint ven¬ture between Nerco Coal Corp, the operator, and Idaho Energy Resources Co. The permit boundary encompasses more than 81 km'- (20,000 acres) on the western side of the Continental Divide. Since the mine began opera¬tions in 1974, it has produced about 82 Mt (90 million st) of coal while moving about 344 hm3 (450 million cu yd) of virgin earth. Annual production averages 4.5 Mt to 6.4 Mt (5 million to 7 million st) of run-of-mine coal. Coal is consumed on-site by the Jim Bridger Power Plant, a 2000-MW generating station. Electricity is transmitted to the Pacific Northwest power grid that includes Oregon, Idaho and northern California. Geology The mine is located on the northeast flank of the Rock Springs uplift. This is a broad, asymmetrical anticlinal feature about 97 km (60 miles) long and 56 km (35 miles) wide with a north-trending axis. This uplift separates the Green River Basin to the west and the Great Divide and Washakie Basins to the east. Precambrian rocks on the apex of the uplift are estimated to be 5200 m (17,000 ft) above the Precambrian rocks in the Green River and Washakie Basins. Normal faults with generally less than 30-m (100-ft) vertical displacement cut through the uplift. The dip of strata on the flanks is generally between 3° and 15°.

Jan 1, 1991

By Claude Hébert

The Grenville structural province, a 400 km-wide belt of Precambrian metamorphic rocks which crosses the province of Québec in a northeasterly direction, is the host of several wollastonite occurrences. Most of these are found in marble and calc-silicate rocks enclosed within or located near intrusive bodies. Reconnaissance and detailed mapping of such zones have helped to identify areas of interest for wollastonite exploration. The most important zone is located in the huge Lake Saint-Jean anorthosite massif in the central part of the Grenville. A recent geological mapping project has revealed the presence of wollastonite in metasedimentary faulted remnant of the roof. The main occurrence consists of diopside and wollastonite in a zone at least 3 km long and 150 m wide. Preliminary sampling suggests and average grade of 50 percent wollastonite with an aspect ratio of 151. Other wollastonite deposits occur in the western part of the Grenville, mainly north and west of Montreal, where the Morin anorthositic complex and a large syenite mass intrude the metasedimentary rocks of the Grenville Supergroup. Marble bands with up to 70 percent wollastonite occur locally at the southern margin of the complex or as an inclusion in the syenite. Significant wollastonite occurrences have recently been found in the eastern part of the Grenville. One of them is located in metamorphosed calcareous rocks which are part of the granulite facies Manicouagan metamorphic complex. A representative sample analyzed 54 percent wollastonite. Farther south, an inclusion diopside-wollastonite gneiss containing an estimated 40 percent wollastonite occurs at the margin of the Pentecôte River anorthositic complex.

Jan 1, 1995

By A. Pinches, R. Winby, P. J. van Staden, M. K. Rhodes, P. C. Miller

This paper is a progress report on the commercialization of using bioleaching for base-metal concentrates. The paper focuses on bioleach processes for recovering copper from chalcopyrite and nickel/cobalt from pentlandite/pyrrhotite. Data is discussed from pilot-plant trials in which an overall recovery >95% was obtained for the bioleaching of copper from chalcopyrite. The pilot plant was operated in closed circuit with solvent extraction and electrowinning circuits for final metal recovery. For the bioleaching of nickel and cobalt from pentlandite/pyrrhotite, an overall recovery of 97% was achieved. Precipitation routines were used to produce a final nickel/cobalt product. The pilot plants were capable of treating a few kilograms of concentrate per day. Prominent features in the design of a 1-t/day (1.1-stpd) copper-bioleach demonstration plant for the treatment of chalcopyrite concentrate are discussed. The plant, which is now under design, will be constructed and operated based on the results obtained from the laboratory pilot-plant campaigns. Issues of scale-up for the demonstration plant, together with integration into upstream and downstream processing, are also addressed. Independently derived capital and operating costs are presented for a possible commercial plant. These cost studies indicate the principle economic issues in considering the application of bioleaching to the extraction of base metals. The benefits of bioleaching complex concentrates that are not amenable to physical beneficiation and economic treatment by conventional smelting are highlighted. Issues, such as the environmental aspects, that illustrate the benefits of bioleach technology are given.

Jan 1, 2000

By R. E. Mclaughlin, R. J. McLaughlin, A. H. Danzberger

Acid mine drainage (AMD) can occur as a natural phenome­non through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhib­it low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations - the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiqui­tous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treat­ment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper. Within the family of chemical treatment processes, there are three principal recognized methods, namely, "Conventional," "High Density Sludge" (HDS) and "Heavy Metals Removal Process" (HMRP). All three are now employed or specified for treating AMO at mining sites which are being reclaimed under Superfund. Only limited data are available for more specialized chemical treatment processes such as "ferrate", borohydride membrane and electrochemical methods. Therefore, these data are not included here. Performance data for these three processes are presented in this paper and comparison among them is made. Comparisons include consideration of water quality, sludge characteristics, and operational ease. Capital and operational cost comparisons of these processes were addressed in a previous paper by the authors (see bibliography). The results presented here are impo1tant not only to metals mining, but are also applicable to other industries experiencing metals-laden acidic wastes including: coal mining and prepara­tion, metal plating, and electronics circuit board manufacturing. The acceptance of any process should be based on bench scale demonstration before implementation is contemplated. The three processes included herein are discussed in relation to the particular sites at which they are in use, or their use is planned. The sites selected were representative of the various types of processes and the wastewater parameters.

Jan 1, 1998

By G. E. Karantzavelos

Introduction Pure alunite (KAl3 (SO4 )3 (OH)6 ) contains 37% A1203. In the alunite ore found on Milos Island, Greece, opal is the principal gangue while some aluminum, iron, and titanium oxides are also present. Processing of alunite ore leads to the recovery of potassium sulfate, alusil (alumina-silica mixture), and sulfur dioxide. An interesting process has been developed in Greece (Svoronos, 1977) consisting mainly of roasting the alunite ore mixed with KCl to disrupt the mineral lattice in preparation for separating its components. The thermal decomposition of alunite at approximately 600°C occurs by the reaction: KAl3 (SO4)3 (OH)6 + nSiO2 + 6KC1 - 4 K2SO4 + 3 A1203 . nSiO2 + 6 HCl + 3H20 According to the process pure alunite mixed with 543 kg KCl, 840 kg K2SO4, 370 kg alusil, 264 kg HCl, and 65 kg H2O are produced. The roasted calcine is leached in hot water. The potassium sulfate leach slurry is then thickened and washed to obtain a solid residue (alusil) plus a solution rich in potassium sulfate. Assuming the alunite ore feed consists of 50% to 60% alunite, the solid residue might consist of approximately 22% to 27% A1203, silica, iron, and titanium oxides. This leach residue could be digested in a hot sodium hydroxide solution to dissolve alumina. An amount of the alumina (approximately 10%) would not dissolve. In addition, part of the silica would dissolve requiring removal from the solution in a subsequent desilication operation. The same leach residue could be attacked by mineral acids such as a diluted hydrochloric acid to extract aluminum chloride (Sawyer et al., 1983). Alumina and aluminum are presently produced from bauxite of which Greece has important reserves. If this aluminous material (alusil) could be beneficiated by any physical process, then it would be considered as a raw material for the production of fire-clay refractories instead of an alternate source of alumina. Experimental procedure Extensive laboratory work (mineralogical and chemical analyses) indicates that alusil is a mixture of liberated (mostly) alumina and silica particles, not a natural silicate mineral. Table 1 shows the chemical assays of two alusil samples that were obtained from a roasted alunite ore leaching pilot plant. The samples used for the experiments were a very fine alusil powder (K80 = 400 mesh, 38 µm). These were pulped in tap water. Desliming of the pulp before each flotation test was ineffective. Flotation tests were performed in a 2000 ml Denver cell. A standard 500-g sample was first conditioned at a pulp density 50% solids for 5 min with hydrofluoric (HF) acid solution (40%). The temperature of the conditioned pulp was measured and kept nearly constant at 50°C. The pH of the conditioned pulp was also regulated to 2.5-3 with HF solution. Then ARMAC C solution (2%) as well as two drops of fuel oil and one drop of AEROFROTH 65 were added and the pulp was reconditioned for 2 min. After conditioning, the viscous pulp was transfered to the flotation cell. It was then diluted with warm water to about 15% solids and floated to separate silica from alumina particles. A rougher froth product that was cleaned and recleaned was obtained from the flotation tests.

Jan 1, 1987

By Johan M. Versteegen

During the production of silicon carbide a by-product is generated, which contains a mixture of crystalline and amorphous silicon carbide. Utilizing the difference in density, shape and surface properties of the crystalline and amorphous silicon carbide, separation tests were carried out with gravity concentration and flotation equipment. The flotation results of the fine fraction of the silicon carbide mixture were not encouraging. The processing of the coarse fraction of the silicon carbide mixture by jigs resulted in a high grade crystalline SiC concentrate with the desired specifications. The separation was largely influenced by the shape factor. An IHC-jig with a newly designed hydraulic drive was used to carry out the test program.

Jan 1, 1988

By D. Kump

The Bullfrog Mine is an underground goldmine that uses the underhand-cut-and-fill mining method. The portal was established on June 18, 1991. Mining is expected to be completed by the summer of 1999. This paper starts by discussing what it took to get from nothing to 2000 tons-per-day backfill, and ends with a hindsight commentary on things that did and did not help.

Jan 1, 1999

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

By A. Chattopadhyay, J. Res

High-level electrical energy can be suitably converted to shock waves of stress that, in turn, may be used for disintegrating hard rocks. This development, known as the electrohydrodynamic method, is very safe and highly economical compared to other methods of rock breaking. This paper deals mainly with development of the equipment and some details of the experimental work carried out with different rocks and concrete block.

Jan 1, 1988

By Cherie M. Tilley

Dynatec Mining Contractors (Dynatec) entered into a contract with Barrick Goldstrike Mines (Barrick) to develop the deep gold ore reserves at the Meikle Mine north of Carlin, Nevada. The Ventilation and Production Shafts were started in early 1994 and were completed in December, 1995. The mine development and mine construction programs were completed in November, 1996. This paper describes the Meikle Mine development program.

Jan 1, 1997

By Peter Bourke

It was in 1982 that the first SK-80 flash flotation machine was introduced at Hammaslahti concentrator in Finland to produce a final grade copper/gold concentrate. Since then the size and number of flash flotation units has steadily developed with the SK-240 being introduced in 1984 and the SK-500 unit in 1990. To date over 130 units have been installed worldwide many of which have been used to maximise the recovery of precious metals such as gold and platinum by preventing overgrinding in the grinding circuit prior to flotation. This paper briefly describes results achieved at several major gold mines in Australia and overseas that operate large flash flotation cells.

Jan 1, 1995

By T. S. Golosinski

Timely and efficient conversion from traditional to sustainable development of mineral resources requires that managers, engineers and other mineral industry professionals become familiar with the related techniques and methods. To fill this need the online Master of Engineering program has been developed at University of Missouri-Rolla. Designed primarily for mature students with an engineering or science background this program allows for specialization in several areas of sustainable development of earth resources. To accommodate mineral industry professionals working in remote locations all courses constituting the program can be taken online, without the need to attend the classes in person. The paper describes the program and discusses the experience gained during the first two years of program offering.

Jan 1, 2003

By R. Matikainen

Since the Brundtland Commission in 1987, the use of natural resources has been an issue of global concern. Minerals are among the most important Earth resources and will definitely be essential for the development of societies also in future. Increasing scientific effort is needed not only to discover new deposits, but also to promote resource management in ecologically and socially sound way. Sustainable resource management is essentially a multidisciplinary challenge of developing life-cycle analysis and recycling of non-renewable resources from local to global scale. It offers great opportunities for geological surveys not only in EU, but all over the world to contribute positively to the welfare and sustainability of societies.

Jan 1, 2003

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

The first of this two part series takes a look at some of the history and types of flotation as well as agents and mechanisms involved in it. Part two, next month, will examine flotation processes as applied to various sulfide and nonsulfide mineral ores. Flotation-"froth" flotation-is a physicochemical method of concentrating finely ground ores. The process involves chemical treatment of an ore pulp to create conditions favorable for the attachment of predetermined mineral particles to air bubbles. The air bubbles carry the selected minerals to the surface of the pulp, there forming a stabilized froth that is skimmed off and from which the predetermined mineral particles are recovered. Other minerals remain submerged in the pulp.

Jan 3, 1982

By Weixing Wang, Zhenghe Xu

The paper applies the principles of the incompressible viscous fluid-flow to studying the movement of particles on shaking table and examines the separating process of tabling according to Bagnold's shearing theory. It is shown that, in addition to the periodic movement, the particles possess the uniform movement on the asymmetrical reciprocating table; the dilation of the particle layers on the table is periodically obtained; on the backward stroke, the particles in the bed are kept loose because the shearing dispersive pressure is of maximum: the differences between the light and heavy particles become greater when the length and frequency of the stroke are greater and the deck motion is more asymmetrical.

Jan 1, 1995