Search Documents

By C. J. Webb, C. J. Paterson, A. Davis

This work focused on identifying, examining and ranking the physical and environmental hazards at inactive and abandoned mine sites in the Black Hills of South Dakota. Earlier inventory projects in the Black Hills concentrated on federal lands, while more recent efforts have examined abandoned mines on state and private lands. The more recent efforts are a result of passage of legislation by the State of South Dakota requiring a comprehensive inventory. The inventory information provides criteria for identifying those sites that require further investigation or characterization of the physical safety or environmental hazards. For most AML sites in the Black Hills, location information is all that is typically needed, because the majority of sites pose little environmental or physical hazard.

Jan 1, 1999

By P. K. Naik, S. C. Das

Leaching studies of low-grade manganese ore containing 31.77% Mn and 23.71 % Fe from Nishikhal, India, were carried out using pyritiferous lignite as a reductant in sulfuric acid medium. The variables studied were quantity of lignite, sulfuric acid concentration and temperature. Regression equations for the extraction of manganese and potassium were determined from 23 full factorial design data. The experimental conditions for the extraction of manganese were optimized using the steepest-ascent method. It was found that 99.03% of the manganese could be extracted in three hours with an ore to lignite ratio of 1:1.8, a sulfuric acid concentration of 1.9 M and a temperature of 99°C. Key words: Leaching, Manganese ore, Lignite, Statistical design

Jan 1, 2003

By G. Knight

It is shown that the dust exposure of all underground workers varies greatly from day to day even though each man did the same job in the same working place each day. The variability follows a logarithmic normal distribution with a geometric standard deviation of about 1.6 for the three dust assessments; total respirable dust, respirable combustible dust and respirable quartz dust in both mines studied. The variability was homogeneous for all men and most jobs. The differences between men doing the same job was found not to be significant and it is suggested that the dust sampling program should determine the average for each job and use this as the best estimate of the exposure for each man.

Jan 1, 1980

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

By Irwin R. Higgins, Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems ere less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIX™) and fixed film biological reactor, Denite®. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1995

By K. Ohga

Japan has produced 14-16 million tons of coal per year in the past several years. About half of the production comes from eight coal mines in the Ishikari coal field, Hokkaido. Most of the gassy coal mines are in this field and the average mining depth of these coal mines has already attained about 700 m from the surface. Therefore, most of the coal mines have suffered from occurrences of coal and gas outbursts. To prevent outbursts and to reduce ventilation air, gas drainage has been carried out at all of these coal mines and these have had successful results. However, the methods of gas drainage differ from mine to mine. In this report, an outline of the main methods of gas drainage are described.

Jan 1, 1987

By R. W. Henn

Introduction Shotcrete, by the American Concrete Institute definition, is mortar or concrete pneumatically projected at high velocity onto a surface. The term gunite is still common in literature. It is a trade name established by Cement Gun Co. of Allentown, PA, around 1911 for a dry mix of fine aggregate material, hydrated at the nozzle, and pneumatically projected at high velocity onto a surface. This article will discuss shotcrete applications, ingredients, mix proportioning, batching and mixing, admixtures, testing, and steel fiber vs. conventional shotcrete. Applications Shotcrete is used primarily by the mining and underground construction industries to temporarily stabilize an excavated rock surface until a permanent cover can be installed. It may also be used as the permanent covering material. Other uses include refractory material, architectural finishes, slope stability, wearing surfaces, repairing existing concrete structures, fireproofing, and corrosion protection of steel. Wet Versus Dry Process In the wet process, all ingredients, including water but not accelerator, are mixed the same way as normal concrete before its placement by pneumatic projection. The accelerator is added in a liquid state through the nozzle at the point of placement. In the dry process, all ingredients, including acceleration in dry form but not water, are mixed just before placement by pneumatic projection. Water is added through the nozzle at the point of placement. Liquid accelerator may be added at the nozzle in the dry process. Ingredients Shotcrete consists basically of the same ingredients as concrete with some limitations. Type I, II, and III cements are used. However, Type II seems to be used most in underground applications. This can be attributed to ground water at most sites having slight to moderate concentrations of sulfates. Air-entraining cement or air-entraining admixtures are generally not used in dry mix shotcrete. It is generally agreed that it is impossible to entrain air due to the absence of the usual concrete mixing action, and the high velocity of impingement of the material on the application surface. Air-entraining cement or air-entraining admixtures are used in wet mix shotcrete. Their use, however, is not widespread due to the placement method and the fact that high velocity air drives off most of the entrained air. Test results are not conclusive in showing any durability increase of shotcrete to freezing and thawing by using entrained air. In spite of current practice, the trend is toward additional research, with more agencies and owners requiring the use of entrained air. The philosophy behind this is that some entrained air is better than no entrained air to increase durability to freezing and thawing. The aggregates used in shotcrete are the same as those used in concrete. However, the largest coarse aggregate presently used is 19 mm (0.75 in.). A typical gradation requirement is shown in Table 1. The water quality requirement for shotcrete is the same as that for concrete. Accelerators are by far the most important admixture in shotcrete.

Jan 6, 1984

By H. L. Hinds

Economic pressures to increase production to profitable levels reduced the Homestake's gravity recovery and overall recovery to un-acceptable levels. The operation of the Home-stake gravity gold circuit has increased gravity gold recovery to over 50%, improved overall recovery and increased mill availability for increased tonnage. The gravity circuit consists of three gravity gold recovery stages. The Circuit has four (4) duplex jigs, four (4) belt concentrating strakes and four (4) concentrating tables.

Jan 1, 1989

By P. Ollivier

The ore-processing plant of the Soremib mine Pour a (Burkina Faso) has now been in uninterrupted operation for 3 years. Ores from the oxidized and non-oxidized zones of the deposit are processed together in one flotation unit. About 60% of the gold is free and is recovered in a gravity processing unit. The residual gold in the flotation concentrate is processed on the spot by cyanidation and carbon-in-pulp.

Jan 1, 1998

By Roy Eric Lurie

Computer based signal processing techniques for obtaining empirical dynamic models from measured mill circuit data are discussed. This modelling is the first step towards designing a particle size control strategy. Experimental data from a computerized acquisition sys tern is examined and analysed, and a number of model identification procedures are applied. The resulting models are compared and a suitable model is selected, illustrating the benefits of computer tools for control system design.

Jan 1, 1992

By Ian Mitchell, Peter Faganl, Paul Haddad, Rob Dunne

During the gold cyanidation process, cyanide can be lost from the leachate by various chemical routes. The products of these cyanide losses include base metal cyanide complexes, thio­cyanate and cyanate. These losses are particularly important when treating pyritic or cupriferous ores since the two most sig­nificant cyanic ides, in order of importance, are sulfides and cop­per bearing minerals (I). Cyanidation of pyritic minerals results in the formation of thiocyanate. The problems caused by cyanide soluble copper minerals are well known to the gold processing industry and have been reviewed by several authors (e.g. 2, 3). An important consider­ation, especially with a number of more recent leaching tech­nologies, is the effect of the CN :Cu mole ratio, R, on the gold leaching kinetics. In order to efficiently leach cupriferous ores, it is important that R is maintained at a level that allows suffi­ciently rapid leaching without excessive use of cyanide. The optimum value for R in a fixed leaching system would appear to lie between 3 and 4. This is based on the early observations that the leaching rate is very slow when R is below 3, with a rapid increase in the leaching rate above 3 (2, 3,4). The leaching rate increases gradually when R is greater than 4 (4). The major Cu(I)-cyanide complex in this range of R values is the [Cu(CN)J]2· species. It has been postulated that leaching occurs due to either uncomplexed cyanide or the fourth ligand in [Cu(CN)4]3·, since the stepwise formation constant for this complex is very small (2, 3). An additional consideration when leaching cupriferous ores is the oxidation of cyanide by Cu(II) minerals, resulting in the formation of cyanate. It has also been reported that both sulfide minerals (5) and activated carbon (6, 7) catalyse the oxidation of cyanide to cyanate. From the above discussion, it is important for the leaching con­ditions to be carefully controlled when treating pyritic and cuprifer­ous ores in order to achieve efficient and economically viable leach­ing. For example, large concentrations of thiocyanate in the leachate would reveal large cyanide losses and thus indicate the need for a pretreatment step to oxidize the sulfides. Alternatively, a low R value would indicate slow leaching kinetics and consequent low gold recoveries, indicating the need for increased cyanide dosage.

Jan 1, 1996

By Caelen D. Anderson

An investigation of a hydrometallurgical method for the recovery of tellurium dioxide from cadmium telluride (CdTe) thin-film manufacturing scrap was conducted. Sulfuric acid/ hydrogen peroxide lixiviation was employed to selectively leach cadmium and oxidize tellurium to tellurium dioxide (TeO2). Experimental variables included solution pH, pulp density, oxidant (H2O2) concentration, temperature, agitation rate and residence time. After one hour of lixiviation, no noticeable increase in grade or recovery occurred; thus, all experiments were performed for one hour. Leaching results showed it was possible to recover at least 74% of the tellurium, while producing a 98% pure TeO2 product. Additionally, an apparent activation energy value of 12.1 kJ/mole (2.9 kcal/mole) was determined. This value, along with results from agitation rate experiments, indicated the reaction was primarily controlled by diffusion through the product layer. During lixiviation, partial dissolution of tellurium proved inevitable. Thus, a second step: ammoniacal precipitation was introduced to recover the aqueous tellurium as a precipitate. A statistical experimental design (DOE) was used to identify the significant effects from the residual effects. Experimental variables included precipitation pH, temperature, initial tellurium tenor and agitation rate. Precipitation results showed that it was possible to produce a low-grade (46% Te) precipitate, while recovering 98% of the aqueous tellurium species. The precipitation pH and temperature (°C) were determined as the significant effects for both the grade and recovery of tellurium. Agitation rate and initial tellurium tenor were determined as the residual effects and did not influence the grade or recovery of tellurium. An illustration of tellurium recovery, as a function of the significant effects, is illustrated in Fig. 1.

May 1, 2012

By S. R. La Brooy, P. C. Earley

Gold and Resource Developments NL (GRD) operates the Macraes Gold Project in East Otago in the South Island of New Zealand, treating a carbonaceous, refractory sulphidic gold ore. The ore is concentrated by flotation, then reground, followed by CIL cyanidation, to minimise loss to the preg-robbing natural carbonaceous material. As the mine has progressed there has been some variation in the preg-robbing nature of the ore, with average overall gold recovery generally in the range 70- 75 %. The Macraes Gold Project has been operating since 1990 and still has an estimated 11 year mine life, which has stimulated the continuing drive to enhance gold recovery. Testwork in 1994 showed there was no improvement in CIL gold recovery after conventional acid pressure oxidation of Macraes Gold Project flotation concentrate. Hence roasting was initially considered as the preferred option to improve gold recovery, being the only established technology to deal with both carbonaceous preg-robbing and sulphide encapsulation. However Newmont Gold Company pressure oxidation technology, as used at Twin Creeks in Nevada, has proved to be applicable to the Macraes Gold Project concentrate. Pilot scale testwork has shown that both roasting and pressure oxidation could achieve similar CIL gold recoveries on the concentrate. However, capital cost, simpler arsenic stabilisation, the ability to operate autothermally at a lower concentrate sulphur grade and simpler environmental consenting factors, has tipped the balance in favour of pressure oxidation. Overall average gold recovery is expected to improve to approximately 84% with adoption of pressure oxidation. GRD has appointed Minproc Limited as EPCM contractor to install pressure oxidation at the Macraes Gold Project, together with upgrading the existing flotation and grind circuits at a cost of NZ$ 30M (US$ 16M). Construction is 60% complete and on schedule for 1 October 1999 start up.

Jan 1, 1999

By Wenhua Wan, Jan M. Mutmansky

Many concerns have been expressed worldwide regarding the use of diesel equipment in underground mines due to the potential health risks associated with diesel particulate matter (DPM). In assessing the risk to the health of miners and designing control strategies for DPM, it is important to know the concentration of DPM in the working areas of a mine. In some mines, significant stratification occurs due to the characteristics of the diesel exhaust, affecting exposure and the ability to measure DPM concentrations accurately. This study outlines some of the concentration profile data obtained during sampling at three mines where diesels were employed. Mine #1 (a gold mine) employed large openings in which a diesel-powered roof bolter was used. Mines #2 and #3 are both room-and-pillar operations with varying conditions. Mine #2 is an experimental mine where two stationary diesels were utilized for sampling purposes, while Mine #3 is a traditional evaporite operation using two mobile diesel vehicles for section haulage. These field studies indicated that some level of stratification occurred in all the mines, but the stratification was not as pronounced in the case of Mine #2 due to the complex pattern of exhaust emissions generated by the vehicles. The stratification seemed to depend on the distance from the vehicle, the mine air velocity, whether the vehicles were moving or stationary, and whether the exhaust was diluted by equipment design features. The concentration of DPM was generally higher at samplers located near the roof and lower at samplers located near the floor. However, this was not found in all cases. This paper provides conclusions on how knowledge of stratification patterns can be utilized in sampling and control of DPM in mine atmospheres.

Jan 1, 1997

By Jr. Foot

EIMCO Process Equipment Company has introduced the new SmartCell series of conventional flotation cells. The flagship of this new development is the 5000 ft3 cell that is the largest available in industry. This new series of cells includes a cylindrical tank design, a conical draft tube and froth crowder. Optional air control, wash water addition and embedded expert control are available. A discussion of the design parameters, energy efficiency, testing, and commercial plant results are presented.

Jan 1, 1997

Overland conveyor belts that exhibit tracking problems under loaded and unloaded conditions can be tested to' determine the root cause of the mistracking. Moveable conveyors are more prone to mistracking due to structure alignment requirements. In addition, belting quality, splice straightness and carcass condition has a dramatic effect on the performance of a belt in relation to tracking. Methods are discussed that are proven to reduce belt mistracking and improve the operational reliability of the conveyor system.

Jan 1, 1995

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By Des B. Bolton, Neil P. Boland

Typically, environmental work on mine sites in Northern Australia involves addressing an individual problem as it arises. However, individual mining companies are moving toward a more holistic approach to managing the interactions between the environment and the mining process and are thus pre-empting environmental problems. This paper presents a broad overview of this holistic approach and provides a few examples, drawn from our own experience, which illustrate some of the tangible benefits to be gained from Environmental Planning.

Jan 1, 1991

By L. J. Warren

Recent research at the Parker Centre in Pe1ih, Western Australia, has provided opportunities to reduce gold production costs by: reducing lime costs in the carbon-in-pulp process, understanding the mechanism of selective extraction of gold over copper using ammoniacal cyanide, and increasing throughput and improving overflow clarify in thickeners. This paper reviews the work of these three Parker Centre project teams, and highlights those instances where the results have been applied to plant practice.

Jan 1, 1998

By L. G. Austin

The data of Dunn and Martin (1978) is reanalyzed using a rigorous application of Hertzian theory to the impact process. The Young's modulus of steel required to fit their data to the theory is a factor of about 10 3, too low compared to the values quoted for steels. Thus, doubt is thrown on the validity of their experimental technique, and it is possible that their values for maximum impact force and stress are far too low.

Jan 1, 2002