Search Documents

By Christof Metzger

This paper discusses the process utilized by the Kiewit?Bilfiger Berger Joint Venture (Contractor) to select, design, and procure the largest mixshield tunnel boring machine (TBM) ever implemented in North America. The mixshield will excavate the 8,534 linear m × 6.7 m ID (28,000 linear ft × 22 ft ID) tunnel for the City of Portland Oregon?s, Bureau of Environmental Services (Owner) East Side CSO Tunnel Project. TBM selection was conducted under a preconstruction contract in which the Contractor, Owner, Construction Management Consultant and Designer collaborated on TBM selection prior to commencement of construction. This paper focuses on TBM design considerations, including the use of one versus two machines, machine configuration,extended-wear protection, hyperbaric interventions, boulder digestion, and erection of a steel-fiber-reinforced segmental lining

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960

By Mark A. Jirsa

The Biwabik Iron Formation is a ~1.9 billion year-old sequence of iron-rich sedimentary rocks that was metamorphosed at its eastern- most extent by ~1.1 billion year-old intrusions of the Duluth Complex. The metamorphic recrystallization of iron-formation locally produced iron-rich amphiboles and other fibrous iron-silicate minerals. The presence of these minerals in iron-formation along the eastern part of what is known as the Mesabi Iron Range, and their potential liberation by iron mining has raised environmental health concerns. We describe here the geologic setting and mineralogic composition of the Biwabik Iron Formation in and adjacent to the contact metamorphic aureole of the Duluth Complex. The effects of metamorphism are most pronounced within a few kilometers of the contact, and decrease progressively away from it. The contact aureole has been divided into four metamorphic zones?each characterized by the composition and crystal structure of the metamorphic minerals it contains. The recrystallization of iron-formation to iron-rich amphibole minerals (grunerite and cummingtonite) and iron-pyroxene minerals (hedenbergite and ferrohypersthene) is best developed in zones that are most proximal to the Duluth Complex contact. ©2007 Elsevier Inc. All rights reserved. Keywords: Iron-formation; Mining; Fibrous; Mineralogy; Metamorphism.

Jan 1, 2007

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining usage in the mining industry. A variety of machines currently finds employment: tunnel boring machines, roadheaders, continuous miners, surface miners, and augers. These machines have advantages compared to drill and blast mining methods, including increased safety, lower cost, uniform muck size, and accurately sized openings. A century of experience with mechanical methods has already paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hardrock mechanical mining machines. Mechanical miners will become integrated mining systems and will determine the design of mines, when several significant challenges have been met.

Jan 1, 2001

To build an effective entry roof beam, a roof bolting or supporting system must be of the ability of providing a clamping force to the bolted roof strata. Currently, two roof bolting systems are widely used to serve the purpose of providing such a clamping force. They are resin and mechanical anchorage bolting systems. Both numerical modeling and double shear testing results indicate that a greater pre-installed load or pretension of a roof bolting system is very critical for effective beam building. Although it?s generally accepted that a mechanical anchorage bolting system can provide a greater pretension than a resin anchorage bolting system does (Su and Poland, 2007 and Peng, 2008), no published field data are available to support such a conclusion. This paper analyzes the results of our field tests on both roof bolting systems, explains why one roof bolting system is better than the other under a typical roof condition, and finally discusses the effective means for coal mine operators to determine the best roof bolting system for their roof conditions.

Jan 1, 2011

De Beers? Finsch diamond mine began operation in the 1960s as a surface project using the latest technology available. During the 1990s, the operation, located about 160 km (100 miles) west of Kimberley, South Africa, began its move as an underground mine. The earlier stages (Blocks 1, 2 and 3) of underground work at Finsch used open stope mining methods, also using the latest in technology. The mine began developing Block 4 in 2004. How-ever, studies on this level showed that block caving was a more efficient mining method than open stoping. It was during those studies that De Beers determined that Block 4 would be a good candidate for testing Sandvik?s automated truck haulage technology.

Jan 1, 2008

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35 percent), ceramics and glass (32 percent), lubricating greases (9 percent), air treatment (5 percent), continuous casting mould flux powders (5 percent), polymer production (4 percent), primary aluminum production (1 percent) and other uses (9 percent) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014).In the 1990s, the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced during this period were consumed in the glass, ceramics and aluminum industries. In the 1980s and 1990s, there were two major lithium operations in the United States: brine operations at Silver Peak, NV and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, NC. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period, it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994).Lithium is still produced from the brine operations at Silver Peak. But in more recent years, Chile has become the world’s leading producer of lithium carbonate from brines. Australia has maintained its position as the world’s largest producer of lithium mineral concentrate, the majority of which is exported to China to produce lithium carbonate and lithium hydroxide (Jaskula, 2014).A spodumene concentrate was also produced at the Tanco Mine in Manitoba, Canada beginning in the 1980s through to 2010 when lithium operations were suspended due to fluctuations in the lithium market price (Martins et al., 2013)."

Jan 7, 2017

By Raymond A. Bradbury

Martin County Coal Corporation's operations are located on Wolf Creek in Martin County in the eastern part of Kentucky. The mining complex was started in 1971 and has grown to a 2.273 Mt/a steam coal operation. All of the production goes to Duke Power Company's Belews Creek electric generating station in North Carolina. Production comes from four seams that are mined by deep and surface mining methods. Surface mining accounts for 55% of the production and the remainder comes from 2 underground mines. Continuous miners are used exclusively underground. The preparation plant was originally designed to take coal at the rate of 907 Mt/h but that has gradually been increased to 1134 Mt/h. Other cleaning equipment includes Daniels DMS vessels, Model 77 Deister tables, 355.4-mm R. & S. Hydro- cyclones, Krebs 254-m classifying cyclones, Daniels froth cells and in 1980, 3 Krebs 508-mm heavy media cyclones were added to recover some lost and misplaced material. CMI centrifugaldryers and a Hey1 & Patterson size 100 thermal dryer are also part of the coal preparation equipment.

Jan 1, 1981

By C. Gregory Knight

Adequate planning for the development, operation, and reclamation of a surface mine requires attention to present and future uses of land, both on the mine site and in the mine vicinity. This paper outlines land use implications of surface mining, and suggests procedures that could link mine planning, mine operation, and reclamation to more general land use concerns. Mining is viewed as a temporary use of land that may irretrievably commit land resources away from some future activities, but may allow other uses, some of which may have been impossible without mining. The paper accepts the premise that surface mining should attempt to minimize environ-mental damage and to maximize future alternative uses of land by appropriate reclamation. I. The Effect of Surface 1'1ining on Land Use Surface mining is a temporary utilization of the land most often criticized because the disturbances it creates are of far greater duration than the actual extractive operation, Resource recovery disrupts existing activity on the land, at least temporarily, and

Jan 1, 1977

By Phil Pennington, D. Jack Adams

Mining and processing of minerals, metals, and fossil fuels can release selenium and arsenic into wastewaters. Both selenium and arsenic are difficult to remove to levels that meet current drinking water and discharge criteria. These metalloids can be used as electron acceptors by microorganisms transforming them back to reduced states, thus removing or stabilizing them. Bioremediation cost effectiveness will be discussed in terms of site information required, microbial populations, co-contaminants, pH, redox, and nutrients. Full-scale, economical ex situ and in situ biotreatments are possible and can produce 1,000’s of times less sludge than conventional precipitation technologies.

Jan 1, 2005

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By B. Simser, T. Butler, A. Hall

The longterm future of Glencores’ mining operations in the Sudbury basin area of Ontario, Canada likely depends on mining deposits at depths below two kilometres. To gain a better insight into the rockmass response to mining, a geological scouthole program has been implemented at Glencores’ Nickel Rim Deep and Onaping Depth Project to gain insight into rockmass conditions ahead of the devel-opment face. The scouthole program involves drilling long (up to 600 m) subhorizontal boreholes drilled ahead of the development end and collecting data about the rockmass conditions from various geophysi-cal and mechanical tools (in addition to conventional core logging). Once all data has been collected and the borehole is available, seismic sensors are installed up to 450 m down the hole as part of the micro-seismic monitoring program with the leading sensor always located ahead of the development end. The recorded seismic data is used to provide realtime insight into the rockmass response to mining. On May 20, 2017 a flurry of seismicity with a maximum moment magnitude (Mw) of 0.7 occurred causing damage to the ramp heading. Data from the microseismic monitoring system had indicated that conditions at the development end were changing prior to the rockburst. A back analysis of the scouthole data indicated a clear anomaly in the rockmass at the location of the rockburst. The scouthole data also provided sufficient information to suggest that once this anomalous zone was exited, mining conditions would improve. With the microseismic monitoring system providing realtime information from the rockmass, the area was re-habilitated and ramp development continued successfully. Details of the rehabilitation and adjustments to the ramp development are discussed. Some correlations between the scouthole data and recorded micro-seismicity are also presented.

Apr 26, 2022

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By K. N. Panigrahi

India bestowed with 6000km of the coastal belt, contains some of the richest and largest placer deposits with a mixture of heavy minerals like ilmenite, rutile, leucoxene, zircon, monazite, sillimanite and garnet. Each of the minerals is having economic value due to its inherent characteristics for industrial use in fields of paints, metallurgy, refractory, abrasive and so on. The reserves of titanium bearing minerals (ilmenite, leucoxene, and rutile) in the country is around 378 million tonnes. More than 90% of the titanium based minerals produced worldwide are utilised for making value added products in the pigment industries. Approximately 8 million tonnes of monazite reserves are available in the country from which several rare earth elements like cerium, neodymium, lanthanum, yttrium etc. can be extracted for use in several industries. The country contains a deposit of about 20 million tonnes of zircon, which is used in foundries, refractories, ceramics and chemicals. India has a reserve of 107 million tonnes of garnet and 131 million tonnes of sillimanite required for the abrasive and refractory industries respectively. Keeping in view the multifarious uses, the beach sand minerals are being exploited to have the economic growth of the nation. Although the process adopted for the separations are simple, the equipment involved are specially designed because of the nature of the material of construction. Starting from the spirals to magnetic separators, all equipments are manufactured outside India, which is not only costly, but the availability also takes much time for fulfilling the import formalities. Unlike open cast mining, beach sand mining is a environment friendly mining because dredging is implemented to cut and pump the loose sand through a slurry pump causing less damage to the surface topography as both mining and backfilling takes place simultaneously. Therefore all out efforts are made to explore the beach sand placer deposits in an economic manner to emerge as a leader in the global mineral industries.

Jan 1, 2005

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

By Vojtech Gall

Pre-support measures for urban tunneling have seen a substantial development in the recent past. Ground improvement techniques, pipe-arch and spiling methods now allow for non-disruptive tunneling at very shallow depths under sensitive structures, rail tracks and roadways. The paper presents experience gained on national and international projects built over the past decade that represent case histories and therefore may be used as guidance for the development of similar solutions for future tunneling projects at shallow depths. Reference projects include tunnels for the Washington, DC Metro, London Underground, Dulles Inter-national Airport, Busway tunnels in Boston and the Ft. Canning Tunnel in Singapore.

Jan 1, 2008

By Dr. Jack M. Gillette

A system of models which simulate surface coal mining operations has been developed for use in mine planning and economic evaluations. Micromodels simulate individual mine operations for equipment selection and mine planning. Macromodels simulate all operations in the complete mine for economic evaluation of reserves. A cash flow analysis model makes a complete discounted cash flow analysis to deter-mine a required coal sales price or return on investment for evaluation of any mining project.

Jan 1, 1978