Search Documents

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By George D. Coumoulos

The following aspects of diasporic bauxite are discussed: The importance of world reserves of diasporic bauxites; the geological, chemical and mineralogical characteristics of the Greek diasporic bauxite; the uniformity of bauxite deliveries; the significance of the absence of organics; the excellent settling properties of the red mud; the production of sandy alumina from diasporic bauxites; the advantages of applying tube digestion systems in processing diasporic bauxites; the conditions for introducing diasporic bauxite in the existing European refineries.

Jan 1, 1984

By Y. P. Chugh

A novel dry and wet air dust filter concept was conceived and demonstrated successfully at two mines. A steel-wool and a fiberglass filter, suitable for underground use were identified through laboratory testing and demonstrated in the mine. The steel wool filter was operated with and without water sprays while the fiberglass filter was only operated in the dry mode. The dry steel wool filter provided a dust capture of 37% at a negligible pressure drop. When fine misting water sprays were used on the steel wool filter, the dust capture increased to 51% again with a negligible pressure drop. The filter screen also remained clean and no change in air flow characteristics was observed as a function of time. The dry fiberglass filter however did not perform as well achieving only 11% dust capture while introducing a significant resistance to air flow. This technology is seen to have several applications in underground coal mines.

Jan 1, 2009

"Hecla Limited has been investigating the potential benefits of using a Spendrup/Compact Filter Technic (CFT) diesel filtration system to remove diesel particulate matter (DPM) from the mine atmosphere to optimize use of the available air. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the scrubber efficiency for dust and DPM which is to be presented in another report. This paper reports on a new mining application of a carbon particulate sensor’s ability to continuously monitor long-term mine DPM levels in conjunction with the scrubber evaluation. Magee Scientific is the manufacturer of the Aethalometer®, a continuous black carbon monitor which has been used extensively in worldwide ambient air quality monitoring networks. Two Aethalometers were used at the mine to assess their potential to continuously track underground DPM levels. In this first underground mine application, the Aethalometers were used to continually monitor black carbon (BC) in the intake and exhaust of the CFT scrubber system. Results showed that an off-the-shelf Model AE33 Aethalometer could continually track underground BC levels for extended periods of time over the course of the six-week trial. Data at the scrubber intake over 14 days of testing showed that DPM filtration would be required less than half of the time to maintain BC levels below 50 µg/m3. If the Aethalometer BC data output were “smart coupled” to control a 200-HP in-mine scrubber, significant electrical cost savings would be realized. INTRODUCTION Mine ventilation airflow quantities are calculated to maintain a safe and healthy environment for miners. Dilution of diesel particulate matter (DPM) is often a key factor used to determine the required quantities of ventilation air (Bugarski et al. 2011). DPM emissions and exposure levels are highly variable depending on mine schedules and activities (Janisko & Noll 2010); however, lacking technology to continuously monitor levels, mine ventilation systems are often over-designed in order to handle worst-case scenarios to ensure that DPM levels are maintained at or below regulatory limits. As mines go deeper it becomes more difficult to supply air, and the development of new shafts for air is not economically feasible (Basu et al. 2008). Cleaning and reuse of available air then becomes an attractive option to maintain good air quality."

Jan 1, 2016

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By L. Adler

To mine safely and efficiently the working conditions must be systematically de¬fined. Their uniqueness distinguishes mining from other engineering professions. The worst case in underground mining is delineated and termed "encumbered space'", since it "seriously impedes motion or action." Working space is inherently hazardous, transitory, and expensive, inducing it to be of low quality, tight and congested, vulnerable and deteriorating, and isolated and inaccessible. These adverse conditions, are damaging to cumbersome, mobile equipment, and affect all activities, including surface work. The conditions are reorganized using the fundamental engineering dimensions: space, matter time, people, and money. Comprehensive tables are presented with attention paid to "disaster potentials". Examples are cited.

Jan 1, 1982

By N. Kuyucak

While Acid Rock Drainage (ARD) occurs naturally, its management poses challenges especially at the decommissioned sites. Two passive systems were designed and implemented at two different decommissioned mining sites in Canada in order to treat the seepage with ARD characteristics. One seep originating from a reclaimed tailings pond was neutral mine drainage (NMD) containing circumneutral pH and dissolved metals (e.g., nickel, zinc) in elevated concentrations. The other ARD from a tailings stack showed net acid drainage characteristics with low pH and higher metal concentrations than regulated limits. Due to the different ARD characteristics occurring at each site, different types of treatment systems were designed and implemented. Both sites experience extreme winter conditions. The NMD has been treated mainly by limestone drain and aerobic systems since 1997. The acid ARD has been treated by a system consisting of an anaerobic sulfate reducing bacteria (SRB) cell, an aerobic cell and a limestone filter since 2004. As this site has no access roads, space, or power, a significant capital cost as well as sludge disposal/storage requirements would have been required to institute a chemical (active) treatment system. Both systems have been successfully treating seepage and producing a water quality year round that could comply with regulated objectives.

Jan 1, 2010

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

"Quang Ninh province is located in the north east of Vietnam and the coal mining in the province generates two thirds of the province’s GDP. The coal is extracted from both open pit and underground mines for the country’s complete coal export and by a share of more than 90% for domestic coal usage. Overburden generated through open pit mines is piled up nearby in the form of large waste rock dumps. The side-hill fill dumping near open pit mines is the source of environmental degradation in the region. Among the current problems at solid waste rock dump sites are dust emissions during and after dumping as well as Acid Rock Drainage (ARD). One of the major existing problems at waste rock dumps is dump stability (comprising erosion, sliding and subsidence issues). The RAME R&D project (Research Association Mining and Environment in Vietnam) is - among other activities - actively involved in the research for stabilisation and rehabilitation of mine waste rock dumps in Vietnam in the form of several sub-projects. The Institute of Mining Engineering I of RWTH Aachen University is leading the sub-project of mine waste dump stabilisation in co-operation with Chair of Geotechnical Engineering and Brenk Systemplanung GmbH. Mine waste dumping in the form of layers as an alternative to the side-hill fill dumping is expected to bring up environmental and economical benefits by minimising the problems of dump sites with the contribution to a sustainable development. Reduction of the post construction settlements, long term stable dump profile with minimum erosion, improvement of material parameters for geotechnical slope stability through compaction from hauling trucks as well as economical evaluation of new dumping concepts are the areas of the current research. The project has been financed by German Federal Ministry for Research and Education (BMBF). The ultimate aim of the sub-project is the compilation of the project results in the form of a "Best Practice Guide" and software based "Decision Support System" for planning and management of solid mine waste dumps."

Jan 1, 2011

By F. V. Antonio, R. S. Pizarro

Masbate Gold Mines, dormant since WWI I, are now back in operation. The ore treatment plant incorporates carbon-in-pulp processing, utilized because of the ready availability of coconut shell charcoal in the Philippines and the high clay content of the ore. A detailed description of the plant, including the surprisingly fast and efficient alcohol stripping facility is presented. Operating data for the plant is provided together with an interesting performance evaluation of mechanical versus air- lift agitated leach tanks.

Jan 1, 1981

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By W. Lee Daniels

Significant deposits (> 4,000 ha) of heavy mineral sands were discovered in the USA Coastal Plain of Virginia and North Carolina in 1989. The majority of these lands support highly productive row crop agriculture, and the development of restoration protocols that would return these lands to agricultural use was deemed to be critical to the long term sustainability of mining operations. Virginia Tech worked closely with all stakeholders to develop appropriate restoration protocols and to coordinate their implementation. Full-scale mining operations at the Old Hickory Project in Virginia were initiated in 1997 by Iluka Resources Inc., and restoration protocols have continued to evolve in response to a variety of economic, technical, and social issues. Approximately 750 ha of land are in various phases of backfilling and final reclamation. Return of these lands to agricultural row-crop production has been complicated by lateral variability in mine soil physical conditions, excessive compaction, and limited topsoil return. However, within the past two years, a series of tailings deposition and soil reconstruction practices have been developed and implemented that significantly improve post-mining soil productivity. Deep ripping and appropriate use of organic soil amendments have been particularly effective at restoring post-mining soil productivity.

Jan 1, 2005

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By T. Kontos

Rogers Group, Inc., is the nation's largest privately held aggregates producer (primarily producing crushed limestone and secondarily sand & gravel) and a major regional asphalt paving construction contractor. The company also has interests in building supplies and coal. Facilities are concentrated in five states in the central U.S. (Ohio, Indiana, Kentucky, Tennessee, and Alabama), with an additional location in Southwestern Virginia. At the request of its then CEO and with support from the company's ownership, Rogers embarked on a strategic planning program in late 1986 by retaining an outside management consulting firm. The ultimate goal of this program was to develop a self-sustaining strategic planning process to inject a strategic dimension into every manager's business thinking and to improve company performance. Since then, Rogers has internalized the outside consultants' strategic planning framework --initially, using it wholesale, and later, greatly streamlining and tailoring both the planning process and product to meet the specific needs of the company. Implementation of strategies developed from strategic planning has resulted in significant improvements throughout the organization. The latest product of the strategic planning effort is a company-wide (or, "corporate") strategic plan that carries the theme of "Market Leadership through Excellence". This paper provides a case study of successful corporate strategic planning by examining the evolution of strategic planning at Rogers and by summarizing the key elements of a sound planning process and product.

Jan 1, 1994

By David E. Siskind

The Bureau of Mines has studied the problem of cracking in residential structure walls from vibrations produced by blasting in surface mines. Direct observations were made of blasting damage consisting primarily of cosmetic cracking in plaster and gypsum board walls. Measurements of structure response and also application of the response spectra analysis single-degree-of-freedom model were used to quantify the frequency dependence of the safe level criteria. An overall summary analysis was performed using the new Bureau of Mines damage observations and data obtained from nine previous studies, including the three analyzed earlier by the BuMines for Bulletin 656, published in 1971. Separate analysis of the high- and low-frequency damage cases, structural response, and two types of construction resulted in the establishment of safe vibration levels ranging from 12 mm/sec to 50 mm/sec (0.5 in/sec to 2.0 in/sec).

Jan 1, 1980

By S. S. Huyett

The opportunity to cooperate with the Mining Department of the Pennsylvania State University in their Student-Trainee Program is accepted by The New Jersey Zinc Company who believes that the participation in this type of a program will lead to a larger supply of high calibre engineers in mining. Trainees compete with other employees to earn the cost of their education while gaining practical experience in the mining industry. The practical experience is arranged to complement the technical education through a variety of work assignments. Job opportunities for the trainee are related to the work requirements of the Company and to the performance of the trainee. Management must consider and deal with a good many problems uncommon with regular, full 'time employees. For a number of reasons this program is recommended to other companies as a means to encourage outstanding young men who are interested in a career in the mineral industry to obtain a professiona1 education.

Jan 1, 1963

By Y. C. Kim

This paper describes the implementation aspect of a blast hole kriging system which has been developed for the purpose of daily ore-waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore-waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBM/PC AT or XT computer, using Fortran language and supplemented by a few Assembly language routines for bit-map manipulation. The emphasis of this paper is on the implementation aspect of the developed system. For this reason, the requirements for practical implementation and the system design considerations are discussed in the paper, as well as the main features of the University of Arizona's BHK System.

Jan 1, 1990

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000