Search Documents

By Z. Zhang, R. G. Reddy

Viscosities of industrial lead slags with various compositions were measured as a function of temperature using a Brookfield viscometer. Based on the experimental data from this study and other investigations reported in the literature, an expression has been developed to correlate the viscosities of lead silicate slags as functions of composition and temperature. The effect of each individual slag component on the variation of the slag viscosity is identified. The composition dependency of viscosity of lead silicate slags is discussed. The calculated results using this viscosity expression are in good agreement with the measured data.

Jan 1, 2001

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By Daryl E. Radcliffe, Raymond M. Stateham

The Bureau of Mines, under a Cooperative Agreement with the Bear Coal Company, Somerset, Colorado, conducted a large scale evaluation of the effect of time lapse on roof stability. Time lapse in this study is the interval between exposure and permanent support of the mine roof. The study indicates that time lapse is not a critical factor in roof stability provided permanent support is installed before catastrophic failure begins. Concurrently with the time lapse study, investigations were made of stress distribution around resin-grouted bolts, the regional stress field, and anomalous geologic conditions. The behavior of the resin-grouted bolts, at least in the Bear mine, appears to fit the Coulomb-Navier Theory. Geologic conditions are primary factors in trends of roof stability that extend across the mine.

Jan 1, 1982

By Barbara J. Arnold

The Electric Power Research Institute (EPRI) and six EPRI-member utilities are sponsoring research to define relationships between coal properties and coal handling behavior. Deratings and outages caused by plugged chutes or bunkers or frozen coal can cost utilities millions of dollars annually in lost energy production as well as in manpower to restore coal flow. There is also the added expense of maintaining redundant equipment to assure a continuous coal feed to the boiler, a common practice for utilities. Over the past two years, researchers at CQ Inc. and Iowa state university have collected and analyzed coal samples to develop a coal handleability index for utilities to use when specifying coals for their power plants. These coal samples cover ranges in ash content, rank, grindability, size distribution, and moisture content--properties that affect the handling behavior of coals. Other properties, such as the washability and ash composition, are measured as well. Over the remaining two years of the project, all of these analyses will be correlated to handling behavior, measured using a triaxial shear tester that determines the strength of a coal under compression. An index will be developed and validated at host utility power plants.

Jan 1, 1991

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By James H. Boettcher

In the second quarter of 1979, ASL Inc. inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ASL acquire the outstanding shares of the S&S Coal Company in West Virginia. ASL had, prior to approaching CNB, sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by ASL is shown in Table I compared with the actual terms the transaction closed with. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fun of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institution providing much of the financing. This article briefly describes the process we went through with ASL beginning with the terms they requested initially and ending with the ones on which the transaction was finally closed.

Jan 1, 1981

By Martín Antonio Encinas‐Romero, Patricia Guerrero‐Germán, Jesús Leobardo Valenzuela‐García, José R. Parga‐Torres, María A. Bracamontes‐Landavazo, Agustín Gómez‐Alvarez

A study was carried out to process a sulfide mineral concentrate from Norwest of Mexico containing 97 g/t Au, 0.15% Cu, and 15% Fe. An oxidative acid pretreatment was investigated using ferric sulfate as oxidant, followed by leaching of gold with sodium cyanide. Scanning electron microscopy, SEM-EDS, and X-ray diffraction, XRD, the analysis confirms the presence of quartz and pyrite species. First, a leaching was carried out without pretreatment, at ambient conditions, T = 25 °C and P = 1 atm, obtaining only a 45.2% gold extraction. Once the presence of Fe and Cu sulfides had been confirmed, the Eh-pH diagrams were constructed for the Fe-S-H2O and Cu-S-H2O systems, where it is appreciated that pyrite and chalcocite can dissolve with high oxidation potentials and forming sulfur, oxidizing to sulfate at highly acidic conditions. The oxidized concentrate was neutralized and adjusted to pH > 10.5; it was leached at ambient conditions, at different particle sizes, 44, 37, and 26.5μm, achieving an Au extraction of 75% using a concentration of 0.5% NaCN, 26.5μm particle size, 20% solids, and P = 1atm. Then the oxidized material was subjected to different temperatures, 25, 50, and 70 °C, under the same conditions and obtaining Au extractions up to 92% at 70°C. Additionally, the leaching process was compared using an autoclave reactor at moderate pressures, obtaining an increase in the extraction of Au up to 98% in 2 h, at T = 70 °C and P = 0.62 MPa.

Jan 23, 2022

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be "land poor" but "coastline rich," meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. The Independent State of Papua New Guinea (the State) recognizes this tremendous opportunity and is taking a leadership role in this emerging industry by becoming a 15% partner in Solwara 1 (with an option to increase their investment to 30%).The Solwara 1 Project has been gaining momentum since Nautilus Minerals and the State signed an Agreement on April 24. This new agreement with the State in which they have staked a minimum 15% interest as a meaningful partner, underscores the State’s continued and widespread support for the Project. Signing of this Agreement was a historical occasion and a milestone achievement for Nautilus Minerals and the people of PNG.The machinery being built for the Solwara 1 Project is taking shape. The Seafloor Production Tools are now over 90 percent complete. Assembly of the biggest tool, the Bulk Cutter, was completed in April this year and assembly work on the Collecting Machine and the Auxiliary Cutter commenced in May and June this year respectively. The Riser and Lifting system, which will be used to transfer the mined material from the seafloor to the surface within an enclosed system, is over 50 percent complete. The critical path for the Solwara Project is to secure a suitable vessel arrangement. Nautilus aims to have this completed by the end of this year."

Sep 1, 2014

By C. R. Pelley

This paper is intended to describe the utilization of Western subbituminous coal as used in a utility-sized steam generator. It compares this coal's characteristics with those of a typical Midwestern and Eastern coal as a base and reviews the various design considerations when blends of these coals are used. The effects of blending various low-sulfur Western coals with Midwestern or Eastern coals to achieve a predetermined sulfur dioxide emission and the resulting alteration in the coal characteristics as they apply to utilization are also reviewed. The blending of coals as one means of complying with sulfur dioxide regulations will take on increasing importance as the various deadlines for compliance with new and existing regulations approach. We must first consider the availability of these low-sulfur coals; and insofar as the Eastern low-sulfur coals have been mined for many years, we have focused our attention on the availability of the coal reserves west of the Mississippi River in the United States, as this is the area to which many people are turning in order to meet this requirement.

Jan 1, 1976

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022

By E. R. Torak

Custom Coals, International has installed and is presently testing a 225 kg/hr. (500 lb/hr.) micronized-magnetite, fine-coal cleaning circuit at PETC's Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program's High Efficiency Preparation Subprogram. The project includes design, construction and testing of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense-medium cycloning of the 300 by 30 micron feed coal using three different size micronized-magnetite mediums, and medium recovery circuits using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Jan 1, 1996

By F. Khorram

Image processing is a technique that simulates the human vision system. This technique enables applying every statistical or intelligent operation to recognize differences. In this way this new technique is used in quality control systems in most industries. Studying sedimentary rocks is very important from the economic point of view. Some units of sedimentary sequences involve different mineral deposits, hydrocarbon and water resources. Therefore it is important to identify and classify different sedimentary rocks. Descriptive classification of sedimentary rocks is usually based on visual and textural features and chemical composition of a sample. In this paper different samples of a limestone mine in central part of Iran are classified. The samples were collected from different parts of the mine and crushed down in size from 2.58 cm to 3.58 cm. The rock samples were labeled based on percentage of chemical and lithological compositions. Each sample was assigned to one of the distinguished groups. The images of the samples were taken in appropriate environment and processed. A total of 74 features were extracted from the identified rock samples in all images. In order to feature dimensional decrease, principal component analysis method was used. Then Bayesian statistical algorithm was used as a useful tool for classification. Classification Correctness Rate (CCR), calculated for the test data sets are %88, %68, %61 and %72 for the first to fourth class respectively. Therefore it can be inferred that the extracted features of images are appropriate indicators for different samples identification. These precise results besides the advantages of image processing technique, which are increasing speed of operation and decreasing cost, appears to be a desirable success.

Jan 1, 2012

In practice, frothers are selected following general guidenlies and verification by laboratory and/or plant flotation tests. The terms “powerful” or “selective,” which are commonly used to characetrize frothers, have intuitive rather than scientific meaning. A research program has been set out to study fundamental properties of the flotation frothers and to identify the tests which can provide information needed to characterize and classify such flotation agents.

Jan 1, 2004

By Steinar L. Ellefmo, Fredrik Søreide

"The Norwegian University of Science and Technology (NTNU) and Nordic Ocean Resources AS, with support from Statoil ASA have carried out a project reviewing the knowledge about seabed mineral resources in Norway to identify and prioritize needs for further research and development.A special focus area in the project has been to increase the knowledge of possible massive sulfide mineralizations along the Mid-Atlantic Ridge. This Ridge is a subsea mountain range which separates the Eurasian and the North American continental plates. In this area, seafloor massive sulphides (SMS) are formed from the volcanic and hydrothermal activities along the Ridge. A large part of the North-Atlantic Mid-Atlantic Ridge between Jan Mayen and Spitsbergen is located on the Norwegian shelf.Analysis and interpretations of multibeam data have been carried out by NTNU in cooperation with the Russian Institute for Geology and Mineral Resources of the Oceans in order to disclose relevant areas for the formation of SMS deposits. This analysis has identified several promising areas."

Sep 1, 2014

The 2014 George A. Fox Conference at the Graduate Center, City University of New York in New York City was presented under the theme, ?21st Century Challenges for the Tunneling Industry. Bruce Grewcock, chief executive officer and president of Peter Kiewit Sons? Inc., opened the conference with a keynote address in which he set the tone for the rest of the day by touching on the many challenges the industry is facing, which are plentiful and complex. Covering the breadth of the industry, he spoke about everything from the technical challenges that come from working beneath the streets of some of the most densely populated regions in the world to the challenges that come from working with the people who live in those areas. ?My observation is that we, as an industry, are being asked to put structures in places where they are needed, but are complex environments to work in,? said Grewcock. ?We work in an industry that relies on some of the most technically challenging engineering in the world, and when we are done with a project, we cover it up and no one ever sees it.? Despite these issues, Grewcock said that, in his opinion, the biggest challenge the industry is facing is that of people; more precisely, where to find the next batch of people. Looking out at the conference-record crowd of more than 400 registered attendees, Grewcock quipped that he saw plenty of gray beards and asked aloud, ?Where will we find, educate and train the people to tackle the issues that this industry will face in the future??

Mar 1, 2014

Fossil resin types occurring in the Hiawatha seam of the Wasatch Plateau coal field, Utah, have been separated according to color and their physical and chemical properties evaluated. These resin types were separated into four color fractions, yellow, amber, light brown, and dark brown. Each resin type has then been subjected to comprehensive spectroscopic examination and other physical methods of characterization. Included among the spectroscopic methods of characterization are FTIR and 13C NMR spectroscopy. Physical properties that have been measured include density, optical, and magnetic properties. These analyses reveal that the resins are distinct from other macerals, predominantly nonaromatic in nature with small amounts of oxygen functionalities and a low degree of unsaturation. The four resin types show distinct differences in certain physical and chemical properties such as density, hexane solubility, magnetic susceptibility, and aromaticity.

Jan 1, 1990

By William Gleason

"Ed Rapp is among those who believe in the saying that necessity is the mother of all invention. Rapp is the president of Caterpillar’s mining group. As such, he is tasked with leading the world’s largest mining equipment maker, and its customers, through this time of lower commodity prices, while also positioning his company to be prepared for better days that lie ahead.The decade-long mining boom fueled by growth in emerging markets and demand for commodities that led to record prices for some metals paused in 2008 with the global financial crisis. However, according to Rapp, thanks to stimulus packages around the world, and in particular the stimulus from China that was focused on infrastructure, the mining sector recovered fairly quickly, and from 2010 to 2012, mining was strong.And then the stimulus stopped. Credit dried up and global growth began to slow down and, in the three years since, commodity prices have declined by an average of 60 percent. Caterpillar expanded during the boom, acquiring Bucyrus, and investing billions into the mining sector. It has felt the pinch of the slowdown as much as any mining company in the world. These pages, and those of other mining publications as well as mainstream media, have been filled with stories of doom and gloom about the industry. But Rapp, while acknowledging that the difficult times have been painful, also said Caterpillar sees opportunity in the slow down and reaffirmed his company’s commitment to the mining industry as absolute."

Jan 1, 2014

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

By Ray E. Harris

New developments have occurred in Wyoming's industrial minerals industry since the 32nd Forum on the Geology of Industrial Minerals in Laramie, Wyoming in 1996. The soda ash trona and bentonite industries have experienced overall growth. Gypsum and limestone production have remained constant, but have the potential for dramatic growth. The mining of zeolite ceased in 1997. The struggling dimension stone industry has increased production, but development has lagged behind the schedule predicted in 1996. The construction of a container glass plant and associated production of glass raw materials, as predicted in 1996 and imminent in 1998, is now on hold due to unforeseen market factors. Increases in railroad and highway construction have, and will, greatly increase the production of construction aggregate for local uses. An iron carbide industry, not foreseen in 1996, is in the planning stages.

Jan 1, 2001