Search Documents

By M. Okido, W. Wei, L. Chai

The kinetics on the growth of Thiobacillus ferrooxidans was studied by use of series piezoelectric quartz crystal ( SPQC ). Arsenic ioninhibits the growth of Thiobacillus ferrooxidans, which is consistent with the previous results by other measuring method. This further demonstrates that the SPQC can monitor the chemical activity of the growth of Thiobacillus ferrooxidans. Cupric ion accelerates the growth of Thiobacillus ferrooxidans. The mechanism was discussed, it was considered that copper promotes the protein enzyme of Thiobacillus ferrooxidans, rustic yanin, to form over the range of cupric ion concentration studied. There action order of cupric ion in accelerating the bacterial growth is 0.067. The growth of Thiobacillus ferrooxidans is dependent on temperature, the apparent reaction activation energy decreases from25.56 kJ / mol to 18.32 kJ / mol because of the addition of 10 mg / L Cu(II) to the bacterial growth solution of pH 2.0 at initial inoculum of 10%.

Jan 1, 2000

By T. Bednarski, T. McCallum, L. Moya, B. Gay

"Molybdenum recovery by solvent extraction has gained interest partly due to advances in concentrate leach technology. Historically, both molybdenum and rhenium have been produced using amine-based extractants with the ability to co-extract both metals. Alternatively, a phosphinic acid-based extractant (CYANEX® 600) can be used depending on the flow sheet. CYANEX® 600 selectively extracts Mo leaving Re in the raffinate, which is a valuable feature in plants which require rejection of the rhenium from the molybdenum circuit. CYANEX® 600 piloting results are reviewed and compared to commercial experiences with an amine-based extractant. INTRODUCTION Molybdenum is most commonly found as molybdenite (MoS2) in primary porphyry deposits (about 59% of global reserves) and copper porphyries (about 39% of molybdenum reserves)[1]. Recovery from molybdenite traditionally involves flotation (concentrates typically containing 85 – 95% MoS2) followed by roasting to produce MoO3. Solvent extraction is also used to recover molybdenum from acidic aqueous solutions resulting from scrubbing of roaster and smelter off gasses and leaching of molybdenite (uranium ores). Molybdenum is also frequently found in low concentrations in copper leach inventories[2]. More recently, pressure oxidation has gained interest to treat molybdenite concentrates. Molybdenum Chemistry The chemistry of molybdenum is complex with a series of extractable species existing dependent on the pH and oxidation state as shown in Figure 1.Under strongly basic conditions, molybdenum primarily exists as MoO42- while under strongly acidic conditions MoO22+ becomes the predominant species. In between, a number of isopolymolybdates such as Mo7O246- and Mo8O264- are dominant. Equations (1) – (3) demonstrate some of the proposed molybdenum equilibrium reactions[1]."

Jan 1, 2017

By K. F. Unrug

Extrapolation of the rock properties obtained from the cores exploration holes to the surrounding areas often causes problems because of frequent sudden changes in the geologic composition of strata. To address this problem, the author has been developing a method of rapid strength testing "in situ," with application of a borehole penetrometer. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. The results are generated by strength determination on the wall of a drill hole at a site. The newest development is a borehole penetrometer that requires only a 1.38.mm (1.5 in) diameter hole. The small diameter of the penetrometer body allows for drilling test holes with production mine equipment such as roof bolters. It opens the possibility of broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 1999

By Louis D. Murino

Compared to coal or many metals industries, talc must be considered a small, specialty market catering to niches and dependent primarily on the physical attributes of the mined and processed mineral rather than the chemical attributes with copper, lead or uranium concentrate, the primary objective is the percent metal that ultimately is refined by the smelter, as opposed to the brightness, particle size distribution, trace impurities or morphology. The latter constitute the important determinants of where, how and why talc and similar industrial minerals are used. This paper addresses the talc market-place: where it is, how much of a market there is, who the producers are, available capacity, market growth, and marketing techniques.

Jan 1, 1984

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By E. R. Phelps

It is very seldom that a completely new project is initiated. Most projects consist of a new and different combination of proven techniques or a combination of proven and new techniques. The theme of my discussion today falls in the second category. Proven methods of water transportation and proven methods of bulk material handling were combined with some new techniques which resulted in a new market for the coal industry and a cheaper fuel supply for the power industry. In this respect I refer to the water transportation of coal from the West Kentucky coal fields to coal burning power plants on the west coast of Florida. Peabody Coal Company, Florida Power Company, Gulf Coast Transit, and Mid-South Towing combined their individual requirements and "know how' to make this project possible. I feel the results speak for themselves since it proves that coal can be mined in the West Kentucky coal fields, transported some 1,200 miles by river barge and some 450 miles by ocean going barges, be delivered to power plants on the west coast of Florida and still meet the competitive prices of gas and residual oil. The unique parts of this project concerns the storage and trans loading facilities for coal from river equipment to ocean equipment near New Orleans; the return haul of phosphate and it's trans loading from ocean to river equipment at the same facility and the use of large ocean going barges. In detail it works as follows: Coal is mined in West Kentucky and loaded into 1,500 ton river barges on the Green River. It is then transported some 100 miles to the mouth of the Green on the Ohio River, then 200 miles down the Ohio to it's convergence with the Mississippi, and then 900 miles down the Mississippi to the trans loading facility some 40 miles South of New Orleans. There it is transferred from the 1,500 ton river barges to 18,000 ton ocean going barges and hauled some 450 miles across the Gulf of Mexico to the Gannon Station of Tampa Electric at Tampa entailing a total haul of approximately 1,650 miles.

Jan 1, 1966

By Georgene Renner

At the beginning of the 1990s, Communism fell and signaled the end of the Cold War. The world rejoiced but also watched and waited to see how those countries would restructure themselves. The 1990 SME Annual Meeting was held at the Salt Palace Center in Salt Lake City, UT. The keynote session featured Alistair Frame, chairman of RTZ; Paul Queneau, professor of metallurgy at the University of Utah; and TS Ary, director of the U.S. Bureau of Mines. The SME Board of Directors voted to hire a Manager of Public Information and Education to be the GEM Program coordinator. This person was to collect and disseminate information that could be used by individual members and Local Sections to interface with government personnel and the general public.

Jan 1, 2007

Introduction Agrico Mining Co.'s Florida mining division has three surface mines and employs nearly 700 workers. The division produces some 6.3 Mt (7 million st) of phosphate rock annually. It is a good business. And Agrico has made it better by making it safer through a new approach to mine safety. In one year, Agrico - the second largest phosphate mining company in the US - recorded a stretch of one million manhours without an accident. That same year, the direct cost of accidents dropped to $9137 from a previous five-year average of about $50,000. Together with Don Roe, division manager of safety and security, Division General Manager Don Morrow made 1981 a watershed year for safety at Agrico. Morrow called on consultants from Safety Management Services of Du Pont's Specialty Services division to strengthen a safety program that was already better than average. From the late 1970s and into 1981, lost-workday cases (LWCs) were costing Agrico an estimated average of $22,000 each. And they were occurring with alarming frequency. In 1977, the company recorded six LWCs at an incidence rate of 0.64. This was followed by a jump to nine cases in 1978. In 1979, both occurrences and the rate increased - 10 LWCs at a 1.19 rate. The number of LWCs decreased to seven in 1980, with a rate of 0.71. Agrico instituted a far-reaching safety program in 1981, which began to take full effect in 1982. LWCs dropped from five in 1981, to three in 1982. And the direct cost plummeted from $110,346 to $28,828. In 1983, the mines recorded only one LWC. Its $9137 cost represented a reduction of $101,209 since the Safety Management Services of Du Pont had been called in. Through early 1984, the LWC incidence rate at the facility's three mines, phosphate drying plant, and transportation department was down to 0.26. This is 84% lower than the 1982 mining industry average, making it the safety leader among all Agrico companies, including its chemical plants. New Approach Agrico had the basics of a safety program in place when the Du Pont consultants arrived. But Du Pont suggested changes in responsibilities and company philosophy that formed the foundation of

Jan 1, 1985

By F. F. Peng

A unique collector dispersion techniques was developed and used to improve the flotation rate and recovery of coarser and ultrafine coal-rich particles in the froth flotation processes. In this novel collector dispersion method, the collector such as hydrocarbon-oil is gasified and transported by gas phase (air stream) into the pulp. In addition to the excellent mode of collector dispersion, the collector-encapsulated air bubbles are generated in the pulp. This approach alters the surface properties of air bubbles and provides the fast rate of flotation compared to that of direct liquid collector addition froth flotation. Using gasified kerosene as the collector, the effect of altering surface properties of bubbles on the recovery of larger and finer coal-rich particles of -1.7 mm (-12 mesh) and -600 µ m (-30 mesh) raw coal samples were studied. The Redstone seam coal obtained from Northern Central region of West Virginia was used in this work. The effect of particle size on oil-coated bubble flotation rate and recovery were also evaluated. The conventional froth flotation test with a liquid form of kerosene addition was also conducted for comparison purpose.

Jan 1, 1991

By K. A. Lapakko, D. A. Antonson

Fourteen samples of pyrite-bearing Archean greenstone rock (d < 6.35 mm, 0.04% < St < 1.22%) were characterized (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing. The only sulfide and carbonate minerals identified were pyrite and siderite, respectively. Quartz, chlorite and sericite typically comprised 90 to 98 percent of the mineral content. For the first 60 weeks, seven samples with sulfur contents less than or equal to 0.16% produced drainage pH values exceeding 6.0. Over this period, six of the seven samples with sulfur contents greater than or equal to 0.20% produced drainage pH below 6.0, with minimum values ranging from 3.2 to 4.7. The seventh sample (0.72% S) had a siderite content of 18%. Small amounts of magnesium and, to a lesser degree, calcium carbonates present in the siderite apparently dissolved to neutralize acid and maintain drainage pH above 6.0. Sulfate release rates generally increased as sulfur content increased, and the rates of pyrite oxidation estimated for individual samples were roughly half to five times that reported in the literature for the abiotic oxidation of pyrite by oxygen. Observed neutralization potentials ranged from 0.2 to 2.0 g CaCO3/g rock.

Jan 1, 2002

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

By H. I. Kim

The leaching of a complex matte in chlorine and chloride media was studied. The matte was prepared from manganese nodules by the reduction smelting-sulfidation route. From XRD analysis, the major phases of the matte were identified as CuFeS2, CuS2, (FeNi)9S8, (FeNi)S2, Ni9S8, Ni3S2, (CoFeNi)9S8 and Co metal. Investigated were the chlorine, hydrochloric acid, hydrochloric acid-oxygen, ferric chloride, ferric chloride-oxygen, cupric chloride and cupric chloride-oxygen systems. The results are discussed in terms of reagent concentration, retention time, leach temperature and gas sparging rate. The chlorination process resulted >99% metal extraction efficiency within a short retention time and at atmospheric temperature. However, there were no preferential extractions of Cu, Ni and Co with respect to Fe. The cupric chloride-oxygen system produced leach liquors with the lowest Fe content and with a high base-metal extraction. Sulfide sulfur was converted to mixtures of elemental sulfur and sulfate in all the studied systems.

Jan 1, 2009

By William G. Pariseau

The flexure of geologic strata, a phenomenon of inter- est to geologists and mining engineers alike, is examined as a sheet bending problem&apos; in Coulomb plasticity. Formulae for the distribution of stress, strain and displacement increments, volume change, change in the length of the central surface and power of dissipation, as well as for the neutral surface shift are given. Strains of any magnitude are considered. The analysis shows that deeply buried strata may bend and develop "tensile" cracks under generally compressive states of stress. It is also shown that bed separation and high capacity props are desirable in mechanized longwall mining, a result in keeping with operating experience. Although speculative at this time, the analysis provides a rational working hypothesis as regards the problem of strata flexure and control.

Jan 1, 1968

By C. L. McKenzie

American Girl Mine is located in the Cargo Muchacho Mountains in the southeastern Imperial Valley of Southern California. Production from the current open pit mine and heap leach recovery system began in early 1989. Previous mining and gold recovery took place commencing in 1987 at the Padre Madre site, situated adjacent to the American Girl site to the southwest. In mid-1990, a 790-tonne-per-day underground gold mine and mill went into production. Approximately 6,500 troy ounces of gold per month are recovered from the combined open pit underground mine operation. Copper in the form of Azurite [Cu3(CO3)2(OH)2] and Malachite [Cu2CO3(OH)2] are abundant in the mined ores (Henshaw, 1942). The high solubility of these minerals in caustic cyanide solutions has a negative impact on carbon adsorption and electrowin processes. This paper presents the results of monitoring programs, process chemistry, and control changes introduced at American Girl Mine to abate production complications in the refinery and measures taken to minimize solution gold losses in the adsorption circuit(s).

Jan 1, 1993

By Wern-ping N. Chen

Pressure tunnel includes water-supply tunnels and tunnels for hydroelectrical power plants. Their design principles are different from those of water/wastewater/conveyance and transportation tunnels. Though theoretical pressure tunnel design guidelines exist, a comprehensive guide to summarize these guidelines to facilitate the planning and design of a pressure tunnel program is lacking. The purpose of this paper is to fulfill this need. It first provides key pressure tunnel design concepts in hard rock environment; then, it illustrates associated final lining design principles, including the design of un-reinforced concrete lining, steel lining, and reinforced concrete lining. Design diagrams and a flowchart for the reinforced concrete lining design are provided.

Dec 1, 2022

By Chris A. Minnucci

In 1978, the U.S. Department of Energy funded a 2-year study to identify and quantify causes of the post-1969 coal mine productivity decline. A large number of factors hypothesized to have affected productivity during this period were analyzed using regression techniques. The results were particularly interesting for two of the factors--mining method and shift scheduling. The study results indicate that the use of longwall mining has an insignificant impact on overall mine productivity, compared to other methods, and mines operating on a two-production shift per day schedule are more productive than mines employing other shift schedules.

Jan 1, 1984

By J. H. Canterford

To date, large-scale solution mining has received little attention in Australia, although the potential of this technique has not gone unnoticed. The possibility of long-term damage to the local environment has also been recognized. Because no two orebodies are the same, it is clear that the application of solution mining techniques and the assessment of environ- mental damage will be somewhat different for different orebodies, even though the general principles will be the same. At present the most significant copper solution mining operation in Australia is at the Mammoth (Gun- powder) Mine in northern Queensland. This mine currently produces more than 3 000 t of cement copper a year.1

Jan 1, 1981