Search Documents

By C. P. Kelley, T. J. McKeon

Several recent developments in fine screening technology have been implemented at the DuPont Starke, Florida plant allowing enhanced zircon recoveries while minimizing operator requirements and total operational costs. The total design concept came about through the efforts of engineers at Derrick Corporation (Buffalo, New York), DuPont Titanium Technologies (Starke, Florida) and Roche Mining (Carrara, Australia). The use of the Kelsey Jigs for zircon recoveries from the tailings stream requires two wet sizing functions in order to operate properly. The first wet sizing is required on the initial mineral slurry feed to the Kelsey Jig. This sizing is intended to protect the Kelsey Jigs internal screen basket from plugging with nearsize particles, thereby keeping production rates maximized. The second sizing function is intended to recover properly sized garnet ragging material, which inadvertently ends up in the tailings stream leaving the Kelsey Jig. The unique machine design developed by the three partners in this project incorporated both wet sizing functions (protection and garnet recovery) into a single patented high capacity wet screening machine fitted with patented screen surface technology. This screen surface technology allowed for high capacity slurry handling capabilities at separations as fine as 230 microns while experiencing no nearsize blinding and extremely long screen panel life. The high open area urethane screen surfaces utilized in the application typically last 20 to 30 times longer than stainless steel wire surfaces. The stacked machine design minimized total equipment requirements and screen footprint requirements, and reduced power consumption and overall installation costs.

Jan 1, 2005

By J. P. Gliddon, G. C. Wade, J. W. Lill

Since 1980 a number of significant changes have been introduced at Palabora in an effort to offset the effects of reduced product price and increased unit costs of production. These changes and improvements include major equipment rationalization programs, the introduction of trolley-assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives, and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation, and their contribution to cost reduction and improved productivity at Paihbora are considered.

Jan 1, 1987

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector is one of the leading sectors where work accidents are most intense because of the constant change of work environment and heavy working conditions. The losses and the halt of production after the accident negatively affect productivity and production efficiency. It has been found that there are very few studies on the use of Data Envelopment Analysis (DEA), which is one of the nonparametric efficiency analysis methods, in the evaluation of mining sector occupational accidents. According to parametric activity measurement methods, it has been tried to show that the DEA can also offer the opportunity to interpret work accidents by taking advantage of its advantages. Due to the application of open-pit mining methods along with underground working techniques which increase the risk factors with respect to accidents at work that occurred between 2012 and 2018 of Western Lignite Corporation (WLC) were tried to be analyzed in the present work. As a result of the analytical work using Data Envelopment Analysis (DEA) for the years 2014, 2015, 2016, 2017, and 2018, inefficiency has been determined in both underground and surface operations. According to the results obtained, it was determined that WLC could not produce enough production in both the underground and surface coal mining operation, despite the accidents that occurred, while it had the opportunity to produce more. In addition, it was found that the increase in accidents occurred more than the increase in the amount of production during the years studied.

Jul 4, 2021

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for the industrial and defense sectors. In 2018, the U.S. Department of the Interior presented the final list of critical minerals that are vital to the U.S. economy and defense [1], which included REEs among other mineral commodities. REEs are not rare, despite their name, but economically viable deposits of REEs can be found only in certain geographical areas, and the political and social conditions characterizing these areas may not always be in favor of mining operations. Mining operations may be placed in great operational and financial risk if operations are planned in such areas. Erroneous decisions by decision makers may lead to a chain of events that can completely shut down a mining project. 

By Rameshwar Sah, Basavaraja Maribasappanavar, Sangamesh Desai, G. Balachandran, Ravi Kant Sagar

The present research work deals with the effective utilization of hematite ore containing goethite, kaolinite and gibbsite losson- ignition (LOI) phases in pellet making without deteriorating product pellet properties by optimizing the induration cycle especially drying and preheating of pellets. Adequate drying and preheating of pellets before sintering is of prime importance to sustain the desired properties of pellets. Green pellets of + 8 to − 16 mm size were prepared in a laboratory disc pelletizer and indurated by varying drying and preheating temperatures in a laboratory Raising Hearth Furnace (RHF). Produced pellets were assessed for physical and metallurgical properties. Improvement in drying and preheating temperature simultaneously helped in mitigating fired pellets’ property deterioration. Drying at 300 °C and preheating at 750 °C helped in the maximum removal of matrix LOI from the pellets before firing and enabled the production of pellets of desired properties. Laboratory scale findings successfully implemented at existing 4.2 MTPA capacity pellet plant of JSW Steel Ltd. Vijayanagar and high LOI iron ores (IOs) utilised which resulted in reduction of average monthly pellet fines generation by ~2 wt. %.

Jun 4, 2022

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By D. A. Wheeler

Invented by Pierre Boutin in the early 1960s the column was a complete break from the conventional flotation cell. 1. When used as a rougher-scavenger, the column is excellent. 2. When used as a cleaner, the results can be spectacular. The very first column tests were carried out using it as a rougher-scavenger in a reverse float where silica was floated from iron. It produced a concentrate underflow as good or better than that produced from roughing and scavenging stages in cells, The froth tailing overflow was better than that produced by several stages of cell cleaning. Column scaleup progressed rapidly from the two inch diameter unit to a semi automated 12 inch diameter column on material from the Iron Ore Company of Canada. A change in operating philosophy within IOCC brought all flotation development, column or conventional, to a halt. At that time, IOCC had an exclusive right to the use of the column in Canada in the field of iron ore. We moved into the field of sulphides. A Canadian copper producer sent ore for testing and the results led to their purchase of the first commercial size of column - a 36 inch diameter machine. It was a mechanical disaster. It took several years to raise sufficient funds to return to that mill with our basic 18 inch square unit. It was to be tested and modified in order to learn how to properly design a large column. Originally used as a rougher- scavenger, it had to produce tails equal to the final tailings from this well run plant. It did, and did so while producing a rougher-scavenger concentrate almost equal to the plant final concentrate. It was finally used as a cleaner and produced concentrate 5% higher in copper than the plant final concentrate with equal cleaner tails. This phase of the column development was carried out under very difficult circumstances. The mill superintendent had realized that if he took the froth removal system from our original mechanical disaster and applied it to a conditioner while injecting air, he would have a flotation cell. He had personally applied for patents on this Maxwell Cell. Our development work was done in his mill and as our results became better and better, our difficulties became worse and worse. We finally had to terminate this work. The 18 inch column installed at Mines Gaspé 14 years later was identical to the one removed from Opemiska. The 18 inch column was tried on various ores over the following years and always produced excellent results. However, it was not really a production size unit. We had always aimed for the 72 inch column (72" x 72" x 44' 9"). Prior to this huge machine, we needed the intermediate 36 inch column. The failure of the original 36 inch diameter unit at Opemiska had raised the possibility of short circuiting inside the column as the cross section increased. The first 36 inch square unit was tested in parallel with the proven 18 inch column. If the underflow of the 36 incher was not as good as that of the 18 incher, short circuiting was a possibility in the larger unit. It had been designed for insertion of drop in partitions, four feed points had been provided and the 36 inch column would have become a modular unit of four 18 inch columns. Testing showed the underflows of both columns to be identical. There was no short circuiting in the 36 inch column. Once we had the 36 incher, we had no fear of the 72 inch column. It is permanently partitioned into four 36 inch columns but uses only one set of instrumentation. All the component parts of the 72 inch column come from the 36 inch unit. In spite of our results, the mining community did not believe the column could work. Finally, in 1980, Mines Gasp6 ordered an 18 and 36 inch column for their byproduct molybdenum

Jan 1, 1988

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By Drupad B. Desai, Bruce Chang, Jay L. Merritt

This paper reviews difficult ground conditions encountered along the alignment of large-diameter sewage tunnels for the City of Los Angeles. It offers a detailed one-of-a-kind solution to a unique problem for shallow urban underground tunnels in a seismic zone, using state-of-the-art materials, technology, and equipment. The following topics are discussed in detail: • Geotechnical Design consideration for tunnel traversing through an active fault zone. • Seismologist evaluation of possible fault-offset problems where a fault zone crosses the alignment, in the event of an earthquake of moment-magnitude 6.5. • Probability analysis regarding "recurrence interval." • Structural design of tunnel subjected to displacement, subjected to axial elongation or shortening, and capable of rotational freedom. • Special joint details.

Jan 1, 1989

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002, after the development of models for magnetic separators, hydroseparators and fine screens. A project funded the US Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Mittal plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2008

By Ben DiFiore, Richard DePew, Nate Long, Adrian Naranjo-Castillo, Chris Petta, Robert Auber

The Walworth Run stream was brick-culverted in the 1800s, converting it to a 16-ft diameter sewer. This Cuyahoga River tributary contributed to the infamous burning river that became the catalyst for USA’s environmental movement. The NEORSD has been working hard to reduce CSOs here, most recently by diverting Walworth Run’s 882 MGD of flow to the new Westerly Tunnel. This had to consider structure age/size, alluvial/glaciolacustrine deposits (requiring several ground support systems, groundwater control), and maintenance of massive flows. This paper examines challenges identified during design that supported the contractor in development of a risk-mitigating plan, culminating to successful implementation.

Dec 1, 2022

By D. Conklin

Annual fish monitoring of the Red River, NM from the town of Red River to downstream of Questa, NM has been conducted since 1997. This long-term dataset, sponsored by the Chevron Mining Inc. Questa Mine provides an opportunity to evaluate the fish community response to natural phenomena, such as landslides and drought. Hydrothermal scars are present on drainages to the Red River, which can contribute large quantities of sediment to the Red River during localized storm events. Sediment inputs from the hydrothermal scars result in decreased habitat and water quality conditions within the Red River. Landslides from the hydrothermal scars contributed large amounts of sediment to the Red River in the summers of 2002 and 2007. Resident trout populations in the Red River after summer 2002 were depressed at sites adjacent to and downstream of the hydrothermal scars. Resident trout populations had begun to recover by 2005 and 2006; however, after the summer 2007 landslide, the resident trout population was again drastically reduced. In fall 2007, 13 resident trout were collected from 11 sites in the approximately 23 km reach of the river, compared to 691 from the same 11 sites in fall 2006. Resident trout density and biomass has gradually increased since fall 2007, and flows have removed sediment from the study reach. A combination of increased sedimentation and decreased water quality were likely responsible for the decreased resident trout populations in the Red River. Drought and the lack of flushing flows appeared to exacerbate the problem of high sedimentation levels from 2001 to 2004. Climate models predict prolonged periods of drought and increased intensity of storm events, potentially resulting in less favorable conditions for the resident trout population of the Red River in this area.

Jan 1, 2011

By Robert E. Barry

For new coal-fired power plants, federal regulations require that emissions of sulfur dioxide be limited to 1.2 pounds for every million BTU'S burned. This is equivalent to coal with a sulfur content of roughly 0.7 percent for Eastern bituminous coals and roughly 0.6 percent for Western sub-bituminous coals. The states and their political subdivisions are free to apply more stringent standards and to develop implementation plans covering existing and new units. Most Western-sub-bituminous coals contain less than 1% sulfur and hence their use, in many cases, will allow a utility to meet the regulations. However, there are problems in using such coals in furnaces designed for Eastern bituminous coals, and furthermore it will take many years to open mines and provide transportation facilities to utilities which are now burning coals with a higher sulfur content. Moreover, pending federal legislation would outlaw strip mining on land to which the federal government owns the mining rights. Those utilities who, for one reason or another, intend to continue burning Eastern bituminous coals with sulfur contents in excess of 1 percent are faced with removing SO2 from the stack gases. The alternative of utilizing coal gasification where the sulfur is removed prior to burning in a power plant is still in the early stages of development. Therefore, a large number of processes are under development for SO2 control.

Jan 1, 1974

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

By S. L. Crouch

The general term "coal mine burp" refers to the sudden and violent failure of in situ coal. Coal bumps occur in most countries where coal is worked by underground methods, and are related to both geological factors and mining tech¬niques. Although no single set of circumstances is solely responsible for causing coal bumps, it is generally agreed that at least one of five conditions is necessary in order for then to occur: 1,2,3,4 (1) the depth of cover exceeds 500-ft., (2) the overlying strata are relatively strong and stiff, (3) the coal is structurally strong, (4) the floor does not heave readily, and (5) the mining method produces high stresses over a large area of the seam. Except for the last, these conditions relate to geological factors that are impractical to control. Consequently, methods of controlling or minimizing the occurrence of coal bumps usually are concerned with mining techniques. Coal bumps have been successfully controlled by both longwall and 'yielding pillar' mining systems 4. The longwall system is particularly effective in controlling bumps, but does not eliminate them completely, especially in strong coal seams being worked at comparatively great depths, say in excess of 2000-ft.5. Under such conditions, auger drilling or water infusion often prove helpful 5,6. These techniques are used to destress or otherwise alter the mechanical properties of the coal in an attempt to shift the peak "abutment pressure" away from the immediate vicinity of the face. Under 'normal' conditions, however, it can be expected that the coal near the face will be crushed under the prevailing high stress conditions and that the peak abutment pressure will automatically be shifted into the solid coal. In this context, coal mine bumps can be characterized as unstable releases of energy associated with successive yielding of portions of the coal seam with progressive mining. Longwall and yielding pillar mining systems are effective in controlling coal bumps because they ordinarily do not allow the zone of peak abutment pressure to become 'surrounded' by destressed coal.

Jan 1, 1973

By C. Slotta, F. Charlier, P. Blomen

"Within the energy concept of the German government, the operating time of nuclear power plants was initially extended from about 8 to 14 years. It is planned, however, that every power plant will gradually be decommissioned until 2025 and that simultaneously the amount of renewable energies will successively be expanded. According to the political state, nuclear energy is a discontinued model. Looking at the global energy market, though, an obviously opposed development can be observed. At the moment, 443 nuclear power plants are running worldwide and further 62 facilities are being built. These about 500 nuclear power stations have to be supplied with nuclear fuel right now and in the future. The present paper will describe the worldwide use of nuclear energy, the extraction of the nuclear fuel uranium and in detail the available and predicted resources of uranium. The conclusion of the paper is the statement that uranium as nuclear fuel is no scarce resource but sufficiently available."

Jan 1, 2011

By Muhammad Zia-ur Rehman, Sajjad Ahmad Baig, Gao Lei Fu, Muhammad Mohsin, Sobia Naseem

The environmental sustainability is linked back to human sustainability; the sustainability development comprises the environment, society, and economics. This study mainly focused on mining sustainability and its impact on the environment of Pakistan. For measuring the level and environmental mining sustainability nature to Environmental Impact Assessment (EIA) of the world’s second largest salt mine “Khewra,” Folchi and Phillips environmental sustainability mathematics (PESM) models are applied. The results indicated that Khewra was deemed to be potentially sustainable for the environment and quality of salt. The results suggest the delicate balance of maintaining sustainability successfully, regarding the mining process in Pakistan which has been affecting the local environment and community so badly. The paper lays emphasis on the potential significance of the model’s application for the attainment of sustainable mining goal. This study is essential for researchers,

May 11, 2020

By R. J. Sheets

"What is the primary responsibility of geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer — ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geoengineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this article will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face.What is our purpose?A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question “What is our purpose?” I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor ground water levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: Safety. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or ground water."

Jan 9, 2018