Search Documents

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation.

Jan 1, 2007

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner's exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines' remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau's Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987

By D. P. Richards

Tunneling in carbonate sedimentary rocks such as lime stones and dolomites can be difficult when solution channels or voids are anticipated. Addressing the risk aspects associated with these formations can be done effectively through the Geotechnical Baseline Report (GBR) by properly characterizing the ground and ensuring that the Owner?s and the Contractor?s interests are represented and protected. This paper presents a review of tunneling difficulties in these rocks and includes a review of site investigations, geologic characterization, and presentation in the GBR. Key construction issues are also discussed, including appropriate excavation technology, mechanisms of face support and groundwater control, and quantifying grout takes.

By F. Dingwu

The latest technology and novel equipments in kaolin processing industry in China are described in this paper. Some typical experimental results are presented, which include laboratory-, pilot-or commercial-scale tests. The characteristics of kaolin processing technology are summarized, and the developing trends are indicated.

Jan 1, 1995

By Paul D. Klipfel

Introduction Mineral exploration interest, principally for gold, in the south-western Pacific has surged to new proportions. This is primarily due to the application of epithermal exploration concepts in the Australian-Oceana region. Other factors that have contributed to the high level of exploration interest include governmental policies supportive of mineral exploration, along with relative ease of tenure access and a relatively short bureaucratic process. This paper highlights exploration and development activities in the North Island of New Zealand, Fiji, Vanuatu, the Solomon Islands, and Papua New Guinea (Fig. 1). It provides a framework to understand the overall recent enthusiasm that has been brought to the south Pacific by explorationists. Through these recent developments, it is clear that the south Pacific region will become a significant gold producing area and thereby worthy of attention and study. Papua New Guinea alone is the free world's seventh largest producer (Table 1). And, with the addition of production from deposits presently being developed, this status is likely to be raised. History Gold was first noted on various Pacific islands in the late 1500s by Spanish explorers. They thought they had reached the legendary King Solomon mines. Since then, the history of prospecting in the southwest Pacific has coincided with the colonization of the region. Settlers in New Zealand extensively mined alluvial and lode gold deposits starting in the 1850s. The spread of European colonization to the more remote Pacific islands from 1880-1940 was accompanied by varying degrees of prospecting activity by planters, traders, and settlers. Some were successful, others may have been successful, but never returned due to hostile indigenous peoples or disease. In general, records of such prospecting activity are meager and exploration leads are, in some cases, gained through local village folk memory. Most early discoveries were alluvial finds. These led to placer operations, particularly in New Zealand, the Solomon Islands, and Papua New Guinea. Continued prospecting located lode deposits such as the Morobe Gold-field of Papua New Guinea, the Coromandel Peninsula of New Zealand, and the Emperor of Fiji. Some areas were prospected thoroughly. Yet others, such as Vanuatu, remained relatively unexplored until the present exploration surge began. During World War II, interest in minerals was diverted. It was renewed significantly until the middle 1960s and early 1970s when regional porphyry copper exploration was conducted.

Jan 10, 1987

By W. G. Pariseau

This contribution describes rock mechanics features of the Davis Cavern at the former Homestake Mine in Lead, South Dakota, U.S.A. The mine is located in the northern Black Hills of South Dakota. In 2003 and again in 2008, the mine site was recommended for development as a national Deep Underground Science and Engineering Laboratory (DUSEL) in cooperation with the Sanford Underground Science and Engineering Laboratory under the South Dakota Science and Technology Authority (SDSTA). The original Davis Cavern was excavated about 9.1x16.8x9.7 m high (30x55x32 ft high) in 1965 (Mitchell 2009) at a depth of 1,478 m (4850 ft). The purpose of the cavern was to house apparatus for detecting solar neutrinos. The experiment ultimately proved successful and earned R. Davis a share of the 2002 Nobel Prize in physics. Recently, a new experiment (LUX=Large Underground Xenon detector for dark matter particles and WIMP's=weakly interacting massive particles) was proposed for the Davis Cavern that required an increase in height of 2.4 m (8 ft). For many years, the Homestake gold mine was the deepest operating mine in North America. Development extended to the 8000 Level (2,438 m). The mine closed in 2003. Pumps were shut off and the water level rose to the 4350 Level, about 150 m (500 ft) above the Davis Cavern. Some six years later after selection for DUSEL proposal development by the National Science Foundation (NSF), access to the 4850 Level and the Davis Cavern was regained. Pumping has lowered the water level to well below the cavern floor. Figure 1 shows the layout and location of the Davis Cavern (Cavity). Detector tank, supporting steel, and so forth were subsequently removed. The cavern was re-supported and new access was developed. By August, 2010, 13,000 ft3 had been removed during enlargement and renovation of the Davis Cavern. Figure 2 shows the detector tank under construction in 1965.

Jan 1, 2012

By John Carr

The tremendous growth in grinding mill size and horsepower during the '70s demanded advancements in gear cutting technology and equipment for the '80s. Computers are used as an aid in the design and selection of the mill drive system; sophisticated computer graphics are used to create manufacturing drawings; and a new generation of gear cutting machines are used to manufacture the gears. These new gear cutters can generate-cut gears over 40' (12.2 m) in diameter at an AGMA quality level exceeding the currenty acceptable standards. The precision of the resulting gear assures maximum tooth contact, which will result in longer gear set life.

Jan 1, 1981

By J. R. Walls

The United States potash industry had its beginning in the early Colonial days. Potash was initially manufactured by leaching of hardwood ashes in large iron pots. Production of potash was recorded as early as 1631 in New Hampshire, and in Maine a few years later. According to the census of 1850, the production of potash was America's most thriving chemical industry and, at that time, 569 plants were reported producing potash from wood ashes. Interest in potash was so great prior to the 1800's that the very first United States patent, signed by George Washing- ton, was granted for the production of potash on July 31, 1790. A new era for the production of potash began when potash was discovered by the analysis from a brine well in 1839 near Stassfurt, Germany while exploring for salt. The predominant use of potash at that time was in the chemical industry rather than agriculture. The discovery, by Justice von Liebig in about 1858, that potash salt contributed greatly to the essential plant food in soil opened up an enormous potential market for a suitable potash material.

Jan 1, 1985

By Gary E. Slagel

The year was 1974. The event - the United States Congress was embroiled over what issues should be included in the proposed national surface mining law. The question - what should be done with underground mines? The leading bills ultimately addressed the environmental impacts associated with underground mines including provisions to protect the surface from subsidence impacts. Amid the fears that this subsidence language might discourage underground mining, sponsors of the bill were asked to explain the meaning of the provision that read "to prevent subsidence to the extent technologically and economically feasible." Was this an attempt to limit mining that caused planned and controlled subsidence? Former Deputy Director of the Office of Surface Mining, Dean Hunt, reviewed some of these historical events in a 1985 presentation before the Eastern Mineral Law Foundation. He reported that in 1974 Congressman Morris Udall took the floor to respond to these concerns expressed by other members of Congress and the industry. Mr. Hunt cited Congressman Udall's July 10, 1974 Congressional Record statement: "The House bill contemplates rules 'to prevent subsidence to the extent technologically and economically feasible.' The word prevent led to fears expressed by the Secretary of the Interior Morton, that the effect would be to outlaw longwall mining, with its obvious subsidence ... in fact the bill's sponsors consider longwall mining ecologically preferable and it and other methods of controlled subsidence are explicitly endorsed." Further, the report that accompanied the front-running bill, HR11500, provided the following clarification on the issue of subsidence prevention: "It is the intent of this section to provide the Secretary with the authority to require the design and conduct of underground mining methods to control subsidence to the extent technologically and economically feasible in order to protect the value and use of surface lands. Some of the measures available for subsidence control include: (1) leaving sufficient original mineral for support; (2) refraining from mining under certain areas---or (3) causing subsidence to occur at a predictable time and in a relatively uniform and predictable manner. This specifically allows for the uses of longwall and other mining techniques which completely remove the coal." It is clear from the preceding statements that Congress considered the removal of all the coal and causing subsidence in a predictable and uniform manner to be equal to or better than leaving support coal and causing no subsidence. While the actual provision in the bills talked of preventing subsidence, a subsequent exception made it clear that the real intent was to control it. This is evidenced in the specific planned subsidence language that appeared in the bills and ultimately in Section 516 (b) (1) of PL95-87, the Surface Mining Control and Reclamation Act. It reads: "...adopt measures...to prevent subsidence ... except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." In spite of this historic record that supports controlled subsidence, something has been lost in the implementation. The primary focus by many regulators over the past few years has been on the "prevent" aspect irrespective of mining method being used. This has appeared to change the original intent of Congress from one of controlling subsidence to one of minimizing damage. The objective of this report is to review some of the current regulatory issues that impede full extraction mining and offer some suggestions on possible ways to deal with these issues.

Jan 1, 1986

With commodity prices rising again and market conditions stabilizing, the Metals Economics Group (MEG) found that most mining companies increased their exploration budgets in 2010. In the groups 21st edition of the Corporate Exploration Strategies (CES), MEG found a 44-percent rise in the estimated worldwide exploration total for 2010. MEG found that the estimated total 2010 budget for nonferrous metals exploration reached $12.1 billion, reinstating almost two-thirds of the industry?s $6 billion in cuts to exploration in 2009. Nonferrous exploration refers to expenditures related to precious and base metals, diamonds, uranium and some industrial minerals; it excludes iron ore, aluminum, coal, and oil and gas. In 2008, exploration budgets were at an all-time high of $14.4 billion. This capped a six-year run in which budgets rose. In 2009, nonferrous exploration budgets dropped 42 percent in 2009 as the global economic crisis and declining prices for almost all commodities took their toll on the industry. Metals prices - the primary driver of exploration spending - have improved markedly since bottoming in early 2009, and have traded well above their long-term trends throughout 2010. In response, major, intermediate and junior companies have all increased their aggregate exploration allocations in 2010. In particular, the significant improvement in the availability of equity financings for the juniors over the past 12 to 18 months has allowed this group to account for the largest share of the overall increase in exploration spending this year.

Jan 1, 2011

By G. Davis

It is well known that the anticipated mineral price at the start of a prospective mineral project can have an overwhelming effect on a property's ex ante value. However, possible price movements throughout the life of a project can also have an impact on this value. This paper demonstrates how different potential price paths can affect project value. When considering commodity price projections for mine valuations, it is thus necessary to estimate not only the expected commodity price at the start of the project, but also the manner in which that price is likely to fluctuate throughout the project's life.

Jan 1, 1995

By H. Lyn Bourne

This is the ninth annual tabulation of royalty information. Again this year, some of the older information has been deleted to make room for more than 30 new entries. Several articles and publications crossed the author's desk this past year that relate to mineral valuation and mineral royalty. Tom Loucks presented a paper, "The Valuation of Hard Rock Mineral Property," at the Rocky Mountain Mineral Law Foundation in Santa Fe, NM in July, 1990. His paper gives an indepth explanation of the definitions and concepts related to mineral valuation. It includes descriptions of numerous legal cases that have dealt with mineral valuation and proper reference is given for each case. Loucks works for the Denver Mining Finance Co. Gold royalties generally range from 5% to 7%, net smelter return. However, Severn Brown sent information that shows a much wider variation. Echo Bay Mines reported in its 1989 annual report royalties that range from 1.5 % to 30% for gold from various gold properties. Brown also sent a copy of an article that appeared in the Dec. 27, 1982, issue of Fortune magazine. This issue carried an article by Walter Guzzardi, Jr. "The Huge Find in Roy Ash's Backyard." The article gives the history of Newmont's leasing in Nevada on property that became the Carlin, Bootstrap and Blue Star Mines. The article states that the initial royalty was 10% that escalated to more than 16%. Another property, the site of Gold Quarry, provides an 18% royalty to the same own¬ers. The article makes interesting reading for those interested in mining history.

Jan 1, 1991

By William Gleason

There was a time, not too long ago, when the most daunting challenges facing those in the mining and mineral processing industries could be solved through better technologies and better practices. But now the challenges that come from the actual acts of mining and processing are just part of the bigger picture. SME?s Colorado Section of the Mineral Processing Division (MPD) hosted its 63rd annual meeting at the Broadmoor Hotel in Colorado Springs, April 25-27 and, while the conference had its fair share or mineralolgy and processing presentations that were heavy on the technical side of things, this year?s conference was also focused on the issues of permitting, regulation compliance and legislative issues. The so-called ?softer? issues, that, if not addressed, can lead to very real and very hard challenges. Under the theme ?Mine your own business - permits, startups, expansions and resources,? even the most dedicated metallurgists were drawn into the discussions of politics and legislation, and how those issues affect their business. Fittingly, Colorado Mining Association (CMA) president Stuart Sanderson was honored with the Arthur C. Daman Lifetime Achievement Award. Sanderson, an outspoken proponent for the mining industry in Colorado and beyond, also presented the keynote address to the lunch crowd where he spoke about framing public opinion toward mining and the efforts of the CMA to move the public opinion dial in a direction more favorable to mining. Sanderson explained that Colorado, once a Republican stronghold, turned after 2002 and now is controlled by Democrats who are traditionally less supportive of the mining industry. Sanderson said the deciding factor in the power shift was money, as supporters of Democrats outspent Republicans in the most recent election cycles. CMA has done its part to keep mining going in the state with a broad marketing campaign that was outlined by Sanderson.

Aug 1, 2013

In its April 1991 issue, MINING ENGINEERING published a salary survey form asking for information relating to engineering and management jobs in the minerals industry. 1038 of these forms were filled out and returned, most of them being received in the magazine's offices at SME headquarters before the end of June 1991. An SME volunteer took on the task of tabulating and analyzing data from the forms, but the press of other business interfered with this work, and publication has been delayed until this issue of MINING ENGINEERING. Appreciation is extended to SME members who took the time to fill out and return the salary survey forms, and our apologies go to MINING ENGINEERING'S readers for the delay in publication. Of the total number of forms received, more than 97% were from SME members. The geographic distribution of the respondents closely mirrored that of SME membership as a whole, about 50% being from the Society's Western Region, 19% from the Central Region, and 23% from the Eastern Region. About 8% were from outside the US. Average salaries for each of the four geographic areas ranged between $55,000 and $60,000, with the highest average in Eastern Region (Fig. 1). Respondents were asked to answer a number of questions formulated to determine if there are significant differences in salaries based on the type of organization for which they work. As indicated by Table 1, salary averages at mining companies do not vary markedly with the size of the company: • Large companies, defined as those having more than $1 billion in annual sales, accounted for just over 16% of the returns. Their average salary was $61,840 per year.

Jan 1, 1992

By Yanli Huang, Qiang Sun, Jixiong Zhang, Yuzhuo Jiang, Dan Ma

Mining accidents due to inrushing water are caused by sudden changes in seepage owing to structural damage to key strata of the aquiclude. The backfill mining method can be used to control the movement of the strata, weaken the evolution of fractures owing to damage by key aquiclude strata (KAS), and control the channel for inrushing water. This study develops a mechanical model of a composite beam on a non-uniform elastic foundation of the KAS by analyzing the coupling relationship between the filling body and the key water-resisting layer of the aquiclude. Equations of the deflection-induced deformation, bending moment, and maximum tensile stress of the KAS are analyzed, formulae to calculate the allowable tensile stress and backfill materials’ compaction ratio (BMCR) to ensure structural stability are derived, and are used to provide the critical BMCR for their structural instability. The results of field measurements show that the subsidence of the roof was 600–700 mm with an average BMCR of 80.63%. Damage to the overlying strata was controlled to ensure safe mining and the disposal of solid waste from the aquifer. The research here is useful for ensuring safety during mining while protecting water resources.

Jul 12, 2022

By G. Lawrence, R. Pieters, A. Leung, T. Pedersen

The Main Zone and Waterline pit lakes at the Equity Silver Mine near Houston, BC (Canada) are the sites of a new 3-yr research program with three primary goals: 1) understanding controls on metal concentrations in the lakes; 2) using mesocosms to test a variety of remediation strategies; and 3) verifying and improving an existing coupled physical-geochemical model with the goal of improving predictions of pit lake water quality. Initial data from two summer surveys in the Main Zone pit lake reveal elevated dissolved metal concentrations (e.g. [Zn] as high as 800 µg/L) present in a two-meter-deep mixed layer, and elevated particulate metal concentrations towards the bottom of the water column. Hydroxide sludge, a byproduct of ARD treatment, is being discharged to the surface waters of the Main Zone pit lake. The sludge sinks rapidly to the lake bottom, leading to deep waters with elevated levels of dissolved O2 and total metals. By contrast, the deep waters of the proximal Waterline pit lake are mildly reducing, manifested by depletion of O2 and elevated levels of dissolved Fe. These reducing conditions have led to elevated levels of As (up to 1500 µg/L) in Waterline pit deep waters. The contrasting behavior of these two pit lakes, as well as the processes controlling metal concentrations in the lakes, will be discussed.

Jan 1, 2002

By R. A. Wyman

What unusual features are there about finding, winning, and using the industrial minerals of Canada which may be of interest and yet not widely known. Have you, for example, ever wondered where the raw material for those distinctive greenish grey statuettes, so readily recognizable as Eskimo carvings, comes from? Although stone suitable for carving is obtained at several northern locations, in recent years the Federal government, the Quebec government, and one or two private companies have shipped supplies of various rock types from other sources to central distribution points in the Canadian north for the express purpose of providing Eskimo artists with raw materials for carving. Canada is well endowed with industrial minerals, the extent and variety of which may be observed by a perusal of Table 1. In this table, materials currently produced are shown in the left-hand column; materials which are bordering upon economic viability are listed in the middle column; and materials which have been found in Canada in possible exploitable quantity, but for which [ ]

Jan 1, 1970

By M. Ahrens, J. Gonser

Gearless mill drives are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as their advantages compared to other drive solutions. Due to the variable speed operation the grinding process can be optimized for ores with varying grinding properties. This leads to significant optimization potential for the plant design as well as for its operation. Furthermore, energy and cost savings due to optimized operation, high system efficiency and high system availability are shown.

Jan 1, 2007

By Ali Jaberi Zamharir, Abolfazl Shoghian‐Alanaghi, Hossein Aghajani, Arvin Taghizadeh Tabrizi

In this study, the leaching rate of molybdenite concentrate was evaluated in sulfuric medium, and the influence of the diverse oxidants including hydrogen peroxide, manganese oxide, copper sulfate on the leaching rate was studied. Also, the effect of the addition of the ethylene glycol to the hydrogen peroxide was studied and results showed that with the addition of ethylene glycol, the leaching rate is increased 55% from 41% up to 80.3%. The optimum condition is achieved as 0.7 M of H2SO4, 4.4 M of H2O2, and 3.5 M of EG at 30 °C within 4 h of leaching time and 500 rpm. Also, inserting the oxygen with the pressure of 6 bar to the leaching autoclave, the leaching rate is increased more up to 86.4%. Finally, the leaching process was studied kinetically and the determined mode of controlling factor was specified based on the activation energy which equals 46.252 kJ/mole indicating the chemical reaction mode.

Jun 5, 2022

By J. D. Miller

Pilot-scale tests indicate that effec¬tive concentration of fine gold from Colorado River sands can be achieved by flotation with the air-sparged hydrocyclone. The fine sands (55% minus 400 mesh and 0.01 opt*) from gravity concen¬tration were processed with a 5-cm air-sparged hydrocyclone (capacity -1.0 tph dry solids). Concentrate grades as high as 5.0 opt were produced in a single stage at a recovery of 75.0%. The separation efficiency was significantly better than that achieved in conventional batch flotation experiments.

Jan 1, 1985