Search Documents

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By L. J. Moore

Introduction Hydrometallurgical solvent extraction (SX) processes – featuring large quantities of combustible or flammable organic solvents - are common in the mining industry for recovering non-ferrous metals such as copper, nickel, cobalt, uranium, tungsten, iodine and lithium. Recent fire loss incidents and the widespread use of sub-grade tank farms and piping trenches, plastic piping, poor drainage, and closely spaced buildings demonstrate opportunities to improve the use of Inherent Safety (IS) in this industry. The mining industry has designed and constructed facilities with an emphasis on personnel safety, production efficiency and cost effectiveness. The use of IS to eliminate or minimize property fire exposures has not seen widespread practice. Lessons learned from the mainstream CPI have not been communicated or applied. As an example, copper SX plants have consistently used design of gravity flow as a cost and production-effective solution for transferring liquids and minerals through the process. In fact, Jergensen1 recommends to “utilize gravity to the fullest extent possible” in design of SX plants. This philosophy has been achieved by laying out SX plants with process equipment at different grade levels so that solutions can flow “downhill”. Because of the use of large quantities of flammable liquids and the potential for these liquids - if released – to flow unimpeded into other areas – gravity SX processes represent severe inherent fire consequences unless costly barriers, drainage and channeling are also provided. It appears that little thought has been given to the fire protection consequences and challenges of this design feature during the evolution of SX plants and most copper SX plants constructed today use some form of a sub-grade processing area (tank farm) and one-way gravity flow. While this layout is used to assure a cost effective operation it has resulted in significant exposures to high value production. The use of sub-grade production units is an inherently unsafe layout where flammable liquids are used and is a layout that would rarely if ever be used today by the mainstream CPI. Gravity-assist layout is only one example where copper SX plants have been designed and constructed without IS in mind. The use of combustible and frangible corrosion-resistant materials – such as glass, wood and plastic - for flammable liquid storage, processing and piping systems has significantly increased the hazards of these facilities. These materials of construction are not rigorous and allow for rapid failure and release of flammable contents during fire exposure. The use of combustible or frangible systems to handle or transport flammable liquids is not a practice seen today in the CPI.

Jan 1, 2006

By W. D. Hausel

The Wyoming Province is an Archean craton which underlies portions of Idaho, Montana, Nevada, Utah, and much of Wyoming. The cratonic block consists of Archean age granite-gneiss with interspersed greenstone belts and related supracrustal terranes exposed in the cores of several Laramide uplifts. Resources found in the Province and in the adjacent accreted Proterozoic terrane include banded iron formation, Au, Pt, Pd, W, Sn, Cr, Ni, Zn, Cu, and diamonds. The Province shows many similarities to the mineral-rich cratons of the Canadian shield, the Rhodesian and Transvaal cratons of southern Africa, and the Pilbara and Yilgarn blocks of Western Australia, where much of the world's precious and strategic metal and gemstone resources are located.

Jan 1, 1991

By W. D. Blackburn

If there is a single key to managing a mineral extraction company, it is the control of productivity. American labor costs, in general, tend to be in the range of 10%-15% of total costs. American coal mining labor costs, however, exhibit ranges of 30%-60% of total costs. Is it any wonder that the industry finds itself at a competitive disadvantage? When labor costs take as much as sixty cents of every dollar of revenue, there is little room for profitability. The American coal mining industry must set as a long range goal the reduction of labor costs to the 10%-15% range of total costs in order to be competitive.

Jan 1, 1986

By Marvin P. Barnes

An attempt has been made to compile and code geologic data relating to twenty of the major porphyry copper districts of North America in such a manner as to permit the use of modern electronic digital computers to retrieve, compare, and build statistical mathematical models from the input. In the exploration process as part of his broader efforts to evaluate the potential of some prospective region, district, or ore body, the experienced geologist consciously or subconsciously compares and fits the observed geologic features to similar phenomena associated with known ore bodies with which he is acquainted. Thus an adequate conceptual "model" of the total geologic environment and type of ore body sought is an essential requirement for the successful exploration effort. Numerous such models of porphyry coppers already exist in the minds and notes of many experienced geologists today. These models are, of necessity, couched largely in qualitative terms and though they may be quite definite in the mind of the porphyry copper expert, the total concept of what constitutes a porphyry copper deposit and environment is difficult to convey in very precise terms. There probably is no such thing as a typical porphyry copper deposit. However, it is well understood that most of the deposits that have been studied have many geological characteristics in common. A logical question then might be: What characteristics are most common or how often do they occur in common, and what is their relationship to other common characteristics ?

Jan 1, 1970

By Gordon C. ‘Bud’ Presley

The pumice and pumicite review arrived too late for the June issue. Estimated domestic production of pumice and pumicite in 1992 was up compared with 1991, according to US Bureau of Mines statistics. The Bureau estimate of domestic production of 400 kt (440,000 st) for 1991 turned out to be 401 kt (442,000 st) of actual production, the lowest since 1989. In 1992, the estimated the value of pumice and pumicite sold or used in the United States was $11.6 million, up only $200,000 from the 1991 value. There was an increase in the mine, or mill, average price from the five-year low of $11.44/t ($10.37/st) in 1986 to $26.42/t ($23.96/st) in 1992. Estimated tonnage produced in 1992 was 439 kt (484,000 st). Apparent domestic consumption was 642 kt (707,000 st), up 135 kt (149,000 st) from 1991. Imports for consumption were estimated to be 215 kt (237,000 st) last year. Domestic production supplied 68% of the demand in 1992, with net imports supplying the remaining 32%. This compares with domestic production sup¬plying 53% and net imports supplying 47% of the apparent consumption in 1988. Exports were about 900 t/a (1000 stpy) for the period 1984 to 1988. In 1989, exports rose sevenfold to 7 kt (7700 st) and to 20 kt (22,000 st) in 1990. The Bureau of Mines reported that the amount of pumice and pumicite exported in 1992 was 12 kt (13,200 st). It is assumed that these exports were from the Pacific Coast because imports, mainly from Greece, continued to be a market factor on the East Coast and the Gulf Coast States in the United States.

Jan 1, 1993

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By D. E. Poole

Injury Prevention: Dependent, Independent and Interdependent In recent years, management-directed (dependent)safety programs have lost ground to the more successful self-directed (independent) programs, where employees take responsibility for their own safety. Today, with the growth of the team concept in industry, a mutual-caring (interdependent) approach to workplace safety is gaining wide acceptance. This presentation compares characteristics and results of the three progressive levels of safety responsibility and explains how to develop a successful interdependent program. The presentation will also detail the common principals that are necessary for safety excellence under any of the management styles.

Jan 1, 2000

By A. D. Davis

The Gilt Edge Superfund Site is a former heap-leach gold mine that currently is being remediated in the Black Hills of South Dakota. Mine runoff water is treated before release from the site. The field pH, before treatment, is about 3, and the water contains arsenic and some heavy metals, in addition to sulfate concentrations of about 1400 to 1500 mg/L. In the Keystone area of the Black Hills, naturally occurring arsenic has been detected in ground-water samples from wells. Keystone City Well #4, which is not used currently, showed arsenic concentrations of 36 parts per billion (ppb) and sulfate concentrations of about 19 mg/L. With field samples of water from these sites, a limestone-based method was successful in reducing arsenic and heavy metals concentrations. The results are significant because previous research with the limestone-based method mainly had involved samples prepared with distilled water in the laboratory, in which interference of other ions such as sulfate did not occur. The research indicates the potential for broader field applications of the limestone-based removal method.

Jan 1, 2011

By G. S. Takenaka

When Bridger Coal Company transformed their operations from surface mining to an underground longwall operation their plans included not only the addition of new mining equipment but also surface fans for a blowing (supply) air ventilation system. The original system concept included a propane gas fired air heater to preheat the intake air during cold weather and a dual parallel fan and duct system. One fan operated to ventilate the mine while the other fan was for stand-by emergency operation. Equipment proposals were submitted in March, 2005 based on the dual parallel fan system. Discussions conducted during the equipment selection process revealed that several alternative system design concepts were available. The alternative concepts included innovation features that not only saved space and cost but also reduced operating expense as well. Many of the features were incorporated into the final design of the system. A comparison of the original system concept and final installation design are presented in the paper in addition to details of the features and the derived benefits.

Jan 1, 2009

By Georges Verly

The estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1984

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By H. Y. Sohn

The paper discusses two processes, flash ironmaking technology (FIT) and moving-bed ironmaking technology (MBIT), which aim to reduce energy consumption and greenhouse gas emissions in the ironmaking industry by using concentrate directly without pelletizing and without using coke.

Aug 1, 2023

By Nasser Madani, SULTAN ABULKHAIR

The abstract of the paper discusses the challenge of quantifying iron content in a coal deposit in Kazakhstan. The iron dataset is limited, coming from only three drill holes and some stope samples, while a large amount of geological information is available from legacy drill hole data. The paper proposes a workflow using multiple-point geostatistics to model geological domains and two-point geostatistics to model iron content within these domains. The results show that the direct sampling (DeeSse) algorithm effectively reproduces the complex seam layers, and sequential Gaussian simulation models the iron within each domain.

Mar 30, 2022

By Jorgen Elbrond

Before and in the early stages of industrialization, mining was the undisputed leader in technology. It represented the high-tech of the time. Early mechanization bears witness to that. Hoisting and rock breaking driven by waterpower are such examples. The mines' use of the steam engine was a major incentive to its development. By these means new mines could be opened and more metal supplied. Understanding of systems was essential for miners when shaping the infrastructure of the mines for the transportation of ore, material and men and for the evacuation of water and for ventilation. The irrigation systems of ancient mines are such examples. However, with the industrial revolution other more specialized branches of industry advanced further, and the mines became users of other industrial branches technologies. The mining industry had, however, always been quick to recognize a good thing and use it, when time was right. But, compared with other branches of industry, the mining industry has the disadvantage of working in a rugged environment with (and actually inside) a raw material which is abrasive and highly variable with respect to mechanical properties. This determines the rather high unpredictability of mining machines' performances and their low availabilities and explains a part of the delays in introducing technological advances.

Jan 1, 1989

By D. A. Meyer

The long and arduous process of bringing aggregate produced in Mexico to the Gulf Coast of the United States really began in the 1970s when the first exploratory trips were taken by Vulcan's geologists. It was not until the middle of the 1980s that all of the elements of the project seemed favorable and the largest capital investment in Vulcan's history was given the green light. The history of the project will be covered along with a discussion of the role that market forecasting played in the process. Is this the first of many or a once in a lifetime project? In July 1987, Vulcan and its joint venture partner broke ground in Mexico for a world-class limestone quarry and crushed stone production facility. This project is the largest ever undertaken by Vulcan's Construction Materials Group, with a total cost of over 200 million dollars -a cost shared equally by Vulcan and its joint venture partner, Ingenieros Civiles Associados, or ICA, a diversified Mexican company which is also the largest construction firm in Latin America.

Jan 1, 1995

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

By Alessandro Navarra, Aldo Quelopana

For decades, open-pit mine planning algorithms have incorporated geological uncertainty and other elements or characteristics for increasingly realistic representations. Among these complexities is the detailing of downstream processes that occur inside processing plants. Previous studies have demonstrated that the strategic mine plan and mineral concentrator design are coupled, and should therefore be optimized simultaneously within the same quantitative framework. However, existing frameworks offer limited representation of operational modes. This work demonstrates an approach to resolving this gap, in an optimization based on a parallelized Variable Neighborhood Descent (VND). The resulting algorithm embeds mass-balancing linear programming (LP) using a DantzigWolfe decomposition. A case study of a Zn-Pb deposit is presented to show the performance reached.

Jun 25, 2023

By A. Nivala, S. Ulgiati, M. Canino

Mining and processing of bastnaesite ore, (Ln)CO3F, for lanthanides extraction is investigated in this paper. This series of elements proved to be applicable for a wide range of high-tech uses. In spite of the strategic importance of lanthanides, no LCA and energy analyses of their extraction have ever been published. We perform in this paper a Life Cycle Assessment of the Lanthanide production cycle, based on available database and literature data from Mountain Pass mine (USA) and other worldwide mining and processing sites, most of which in China. We investigated three main steps: mining, milling (including transport, grinding and drying), and flotation (for lanthanide chloride extraction). We do not investigate here the separation of pure oxides from lanthanide chloride, a compound which is also marketed as such. The conventional LCA was integrated by means of energy and emergy evaluations, aimed at investigating respectively the global energy cost and the environmental sustainability of the process. Indicators of material intensity, thermodynamic efficiency, and environmental impact (including LCA and ecological footprint impact categories) are calculated and discussed.

Jan 1, 2005

By R. S. Jurani

Sunshine Mining Company's Kellogg operation is the primary silver producer in the United States, and maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and uncertain silver market, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a 2-year, $400 000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants, thereby saving the company approximately $650 000 per year.

Jan 1, 1987