Search Documents

By E. J. Onuscheck

With passage of the Federal coal' Mine Health and Safety Act of 1969, many challenges have been directed to the industry's mining and safety engineers. The most critical challenge is that of ventilation. The language concerning ventilation in many sections of the Act could very well deprive or limit the mining engineer in planning the ventilation for new mines, since the Act requires federal approval of all ventilation plans. Dependent upon approval and of course application of the law, this could, due to economics, prohibit the opening of new mines in some cases. Petitions for modification of some mandatory standards relating to ventilation have already been filed under Section 301(c). It is quite possible that many of these standards may be modified.

Jan 1, 1970

By David J. Dunn

Materials related problems at mines can be big ones - like a newly completed 1 -m (3.5ft) water pipeline burst during initial filling, grinding ball consumption at double the typical norms on startup of a new semiautogenous grinding (SAG) mill circuit or 30 open-pit haul trucks in the shop for new bed liners after less than a year’s service. Materials engineering provides solutions to these kinds of equipment problems by selecting good materials and designs, by trouble-shooting service failures and by maintaining high quality in vendor-furnished materials and components. Materials with good properties, correctly made and fabricated, correctly installed in mining and processing equipment, produce ore and final products reliably and efficiently. Materials engineering, applied during design phases, specification writing, and receipt and installation of materials, ensures that equipment will have the best possible shot at performing up to expectations. Good calls on materials properties - specifying state-of-art materials produced by competent manufacturers - help mine managers to reduce downtime and mining and processing costs. Materials that are improperly made or specified can make a mining operation less efficient or, possibly, uneconomical.

Jan 1, 1992

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several levels — basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP during 2004 increased by 4.4 percent. The nominal GDP was about $11.7 trillion. Housing starts were up by slightly more than 4 percent for the year. And the nation’s unemployment rate decreased to5.5 percent in 2004 from 6 percent in 2003. Interest rates continued to be low (prime rate was 5.25 percent at the end of 2004) but have risen gradually, following rising inflation.

Jan 1, 2005

By A. Sinha, C. Sawmliana, P. Pal Roy

Using the newly developed and permitted explosive Pentadyne-HP (Gulf Oil Corporation Ltd., Hyderabad), the Blasting Department of the Central Institute of Mining and Fuel Research, Dhanbad experimented at the GDK-5 Incline, RG-1 Area of the Singareni Collieries Company Ltd. (SCCL) to establish one modified angular cut blasting pattern as an alternative to conventional solid blasting in India to obtain longer pull, as well as to achieve at least 40 t of coal in a single blast round for the deployment of diesel load-haul-dump units at the face. This permitted explosive satisfied the statutory requirements of incendivity characteristics applicable to P5 explosives of the regulatory agency Directorate General of Mines Safety (DGMS) of India. The present paper summarizes the development of this new blasting pattern and its possible use in Indian coal mines.

Jan 1, 2010

By Tim O’Neil

Many mining companies try to fight their way up from small operator and exploration company to major producer. Not many companies make it. Cambior Inc., formed in 1986, is one company well on its way to making it as a major operating company. In 1993, Cambior surpassed 15.5 t (500,000 oz) of gold production and began operations at its world class Omai gold mine in Guyana. At the same time, the company has embarked on a program of geographic and minerals diversification. Cambior, a Canadian company, now has interests in eight mines, three development projects and more than 100 exploration properties in North and South America. The company’s goal is to derive 70% of its income from gold and 30% from base metals and other minerals. Cambior’s moderate diversification into base metals gives protection against negative gold price fluctuations. It also balances the typically short term gold mines and the longer term base metal mines.

Jan 1, 1994

By D. G., Bosse&apos

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices. These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground. Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing. These are fairly well understood and provide the starting point for decisions. Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X. This additional major variable is not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures.

Jan 1, 1983

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60's and early 70's efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70's. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By James Wm. White

Computer based dispatching in open pit truck haulage operations yields many benefits of current interest to mine management. The key tangible benefit is a substantial productivity increase with a given fleet of equipment or, alternately, a significant reduction in equipment required to meet production quotas. Other tangible benefits, depending on the operation, include minimizing rehandle, meeting several blending constraints simultaneously and ensuring a target plant feed rate. Intangible benefits include production forecasting, performance comparisons of trucks or shovels of different manufacture and extensive on-line report generation. Recent advances in mini and micro computer hardware and software and solid state electronics permit design and implementation of system features not feasible even a few years ago. Here we discuss many of these recent developments with emphasis on system aspects and dispatching algorithms.

Jan 1, 1983

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By David L. Hill

Newmont Gold Company's Mill No. 4 is located along the Carlin trend, about 25 miles North of Carlin, Nevada. The plant consists of a primary grinding circuit using a 7.2 m (22 ft) diameter by 2.6 m (8 ft) long semi-autogenous mill along with a 2.3 m (7 ft) diameter cone crusher. Secondary grinding is performed in a 4.8 m (14.5 ft) diameter by 9.2 m (28 ft) long overflow ball mill in closed circuit with a set of 66 cm (26 in) diameter cyclones. The ground product is fed to a typical carbon-in-leach gold leach circuit. The grinding/crushing circuit operation and control scheme are the topics of this paper.

Jan 1, 1993

By K. S. Whiting

Elevated concentrations of copper, cobalt, and arsenic within the Panther Creek Basin sediments in north central Idaho prompted an evaluation of the sources of the metals. Potential tailings and waste rock source samples collected at the head of Blackbird Creek were compared to sediment samples in the Panther Creek Basin using electron microprobe techniques. The mineral types, degree of alteration, and the morphology of the metal-bearing sediment grains within Blackbird and Panther Creeks were found to consist of copper-, cobalt-, and arsenic-bearing sulfide minerals.

Jan 1, 1997

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By M. L. Smith

SAG mill throughput is often a bottleneck in increasing metal productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility which is also relevant to the rock fragmentation that is achieved by blasting. The relation between the size distribution and fragility of the feed and of the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1993

By John C. Braithwaite

Gold production commenced in New Zealand during the gold rush of 1861, and recovery to date is over 900 tonnes, almost 60% of which was alluvial. New Zealand pioneered development of bucket line dredges during the 1880's. The advent of the modern hydraulic excavator and increased gold price led to a resurgence in alluvial production with about one hundred plants in operation in 1988. The processing plants are mainly floating, with throughputs of 50-100m3/hr fed by backhoes of 20-40 tonne operating weight. Some larger plants with more sophisticated recovery systems have commenced over the last few years, with the largest using a 180 tonne backhoe.

Jan 1, 1989

By J. R. Muhm

Environmental due diligence investigations, also known as Phase I Environmental Audits, are increasingly important to major investors, venture partners, or prospective purchasers or sellers of mineral properties. Knowledge of environmental risks associated with a property will allow better appraisal of a property's overall desirability prior to completing the transaction. It is possible that the cost of environmental cleanup could exceed the value of the property. Topics appropriately investigated include permit status, water quality, past use of the property, hazardous materials management, storage tanks, public records pertaining to the environmental character of the property, and environmental costs.

Jan 1, 1991

By A. A. Dor

Recent developments in the design of concentration plants have reflected the increased recognition that has been given to the economic and metallurgical advantages of autogenous grinding. This has manifested itself in the increasing adoption of primary auto genous grinding in iron ore 'beneficiation plants in North America. Table 1 lists eleven major iron ore beneficiation plants which have either been put in operation since 1961 or are under construction at present. Seven out of these eleven plants have adopted primary autogenous grinding. Four of them have coarse grinding mills (8 to 14 mesh) and three have fine grinding primary circuits (48 to 65 mesh). Their nominal capacity totals 26. 2 million ltpy of concentrates or pellets, representing very nearly 75% of the aggregate capacity 135. 3 million ltpy) of the eleven concentrators listed. For a long time there was a tendency to consider that primary autogenous grinding was only applicable to suitable coarse grained ores, However, extensive testing of a very wide variety of ores, and actual operating performance in several commercial plants, seem to have established beyond reasonable doubt, that the majority of mineral ores which the beneficiation engineer may be called upon to process can be ground autogenously. The basis for the selection of autogenous or conventional grinding mills, becomes principally economic and depends on the liberation characteristics of the ores under consideration and their relative hardness and grindability.

Jan 1, 1965

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012