Search Documents

By L. Barry Phelps

Coal mine drainage, which occurs predominantly as acid mine drainage in the East, is a serious contaminant of surface and groundwater systems (Appalachian Regional Commission, 1969). Treatment of this pollutant can be very costly and is often difficult to achieve (Appalachian Regional Commission, 1969). A major source of coal mine drainage in surface waters is polluted ground- water discharge, therefore treatment of surface water does little to combat groundwater contamination. Prevention of the formation of coal mine drainage and restricting its entrance into the groundwater protects both surface and groundwater systems. The formation of acid mine drainage may be inhibited by preventing contact between toxic spoil, air, and water (Grim and Hill, 1974). This may be accomplished by surrounding toxic spoil with a relatively impermeable barrier, thus restricting groundwater and oxygen flow through the toxic zone. Toxic spoil packages constructed in this manner would minimize the entrance of acid mine drainage into the groundwater system, allowing dilution by uncontaminated water to occur. If successful, concentrations of coal mine drainage would be reduced below toxic levels.

Jan 1, 1981

By Donald J. Olson

The North 27th St. ISS Extension tunnel will, under present plans, be the last constructed section of Milwaukee Metropolitan Sewerage District?s (MMSD?s) existing deep tunnel system. The 6.5 m (21 ft) finished diameter tunnel is approximately 3,260 m (10,590 ft) long and is located in NE Milwaukee County. When disputes over the pro-cesses to be used in owner-directed pre-excavation grouting in rock threatened the completion date stipulated between MMSD and the State of Wisconsin, the MMSD and J.F. Shea, the contractor, entered into a unique agreement. Shea accepted responsibility for all shaft and tunnel grouting and water control during the project in exchange for settlement of claims related to grout quantities and perceived delays. This significantly reduced risk for the MMSD and helped ensure the stipulated completion of the project.

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By B. Listerud, G. Zhan, M. A. Jones

Barrick Goldstrike Mines Inc. (BGMI) operates the Betze-Post openpit and the Meikle and Rodeo underground mines. Because the majority of the orebody is located below the water table, mining at BGMI requires a significant dewatering program. BGMI has a comprehensive dewatering and water management system that experienced a peak dewatering rate of 4,400 L/s in the mid 1990s. Changes to the hydrologic/hydrogeologic system caused by the mine dewatering have been monitored by an extensive network of groundwater monitoring wells and surface water monitoring stations, which cover about 1,550 km2. In addition to the monitoring program, a new tool, called Interferometric Synthetic Aperture Radar (InSAR), has also been used to enhance the evaluation of changes. Finally, a groundwater flow model has been developed that successfully simulates and predicts aquifer responses in the mine area and region. The well-calibrated flow model has served as a reliable tool to develop dewatering and mining plans, and project post-closure hydrologic conditions in the region. This paper introduces the BGMI dewatering and water management system and the means used by BGMI to evaluate and anticipate hydrologic responses in the region. The water management and analysis system has been and continues to be an integral part of managing ongoing operations, planning and pricing out future activities and evaluating the long-term effects of mine water handling.

Jan 1, 2011

By R. E. Nelson

The Alton Coal project, located in south-central Utah, lies at one point just over six miles from Bryce Canyon National Park. This region of the southwestern United States has been called the "Golden Circle" of national parks and monuments. Can a mine be inserted into this region so that it does not intrude on this spectacular landscape? The Alton Coal Project is a proposed surface coal mine designed to serve as the fuel source for the Harry Allen Power Plant, a 1,000 megawatt generating station planned for a site 25 miles northeast of Las Vegas, Nevada. The mine and the power plant will be connected by an underground pipeline through which coal will be transported in slurry form.

Jan 1, 1988

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

By R. D. Schmidt

An in situ leaching geochemical simulator consisting of flow, mass transport, and graphics support programs has been developed. Two dimensional flow in heterogeneous porous media is modeled using a semi-analytic boundary integral technique. This method involves mapping streamlines to straight line segments in the complex potential plane. Leachant concentration and mineral values are modeled in this plane using the (one dimensional) potential coordinates. A fully implicit finite difference scheme is used to solve the resulting coupled system of four concentration equations. Graphical representations of streamline patterns, concentration histories, profiles and recovery curves are generated. An application of the model to uranium leaching in a heterogeneous aquifer and ore zone setting is presented.

Jan 1, 1985

By Randolph E. Scheffel, David C. Fitch, David K. Hogan, Mark R. Welsh

In Oct. 1981, Ranchers Exploration and Development Corp. began producing silver bullion from the Escalante mine and mill complex, located in southwestern Utah. Current in-place reserves are estimated at 2.42 Mt (2.67 million st) of ore, containing about 936 t (33 million oz) of silver at an average grade of 428.5 g/t (12.5 oz/st). The vein-type deposit is being mined underground through a decline that is currently 864 m (2,835 ft) in length, but will ultimately be at least 1.5 km (5,100 ft) long. The mine is completely mechanized with rubber-tired equipment, and is producing 680 t/d (750 stpd) of ore, five days a week, or 177 kt/a (195,000 stpy). Additional capacity is available. The cyanide leach mill and associated refinery are presently producing 4.35 t/month (140,000 oz/month) of silver bullion-an an¬nual rate of about 52.25 t (1.68 million oz). With minor modifications, the mill can produce up to about 70 t/a (2.25 million oz/year), and expansion is currently underway. History The Escalante property is located 68 km (42 miles) west of Cedar City, UT, on the west side of the Escalante Valley, where the vein forms a gentle ridge in an area of low, rolling hills. For years, the vein has been the object of considerable exploration, but never became more than a sporadic producer, primarily due to low silver prices. Heber Holt of Enterprise, UT, staked the original four claims in 1896; they were patented in 1910. During the next 48 years, limited exploration and mining activity was conducted on the property. Systematic evaluation and development did not, however, begin until March 1958, when Samuel S. Arentz, a prominent mining engineer and consultant, formed several joint ventures with mining and oil companies that conducted drilling, drifting, mining, and water drawdown tests on the property. However, it remained uneconomic, principally because of low silver prices and costs for pumping large flows of underground water. In 1975, Ranchers obtained an option on the property and in 1979 began a drilling program. As of May 1982, the company had drilled 70 core holes, bringing the number of exploratory holes drilled on the property to 138. Test mining began in 1979 as silver prices increased, and full mine development began in 1980. Mill construction began in Sept. 1980, and on Aug 29, 1981, the first ore was fed to the mill.

Jan 9, 1982

By Takayoshi Otsuka, Taher Elsamni, Ashraf Bou-Krisha, Takaya Takimoto

"INTRODUCTION Tunnel is a closed space structure and it is necessary to ensure the sufficient time and route for safe evacuation for the tunnel users in case of a tunnel fire. In order to do so, damages and collapse of the tunnel linings and the secondary disasters can be avoided. Furthermore, the road tunnel is one of important infrastructural facilities and stopping its function for a long time for a tunnel fire could cause a great economic loss. Therefore, the tunnel structure shall be the one which can be repaired as soon as possible, and the fire protection methods need to be selected among those which enable the service to start as early as possible. The necessity of the fire protection works is evaluated for the tunnel structure with the consideration of the expensive tunnel construction cost and the economic effects of the tunnel service. Naturally, the fire protection works, which can protect the tunnel linings from the tunnel fire with small repairs, are inevitable. Design engineers of the fire protection works estimate the scale of fire from the degree of damages on the linings and its repair cost, the effect of fire extinguishers placed inside of the tunnel, the secondary disasters in accordance with the tunnel lining damages if any, and the ratio of fire protection cost calculated from tunnel operation cost. Based on this information, the engineers design the fire protection works according to the permissible limits Among the design cases of the tunnel fire protection in Japan, as shown in Table 1, there is no cases that used the fire temperature-time curve to design the fire protection works for large fire caused by vehicles catching fire. However, the most of cases used 30-60 minutes for fire duration based on the entry prohibition of dangerous goods carrying vehicles or the effect of early fire fighting. This paper will study the variation between different methods used for fire protection in road tunnel in Japan to evaluate them and try to found some recommendations. Especial l care will be attention to Polypropylenes (PP) which is starting to be applied lately."

Jan 1, 2016

By Fiona M. Doyle Garner

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°-200°C. Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions of various metals, singly and in mixtures. Single solutions of Fe, Xi, Cu, Mg, and tin precipitated aFe2O3, Ni(OH)2, Cu2O, Mg(OH) 2 and ?Mn203 respectively during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe20k. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versa- tic solutions are similar to those for iron hydrolysis in aqueous solutions. Infrared spec- troscopy and thin-layer chromatography of mixed iron-nickel Versatic solutions indicated that mixed Fe-Ni carboxylate complexes are present. Magnetic interactions between mixed complexes are thought to be responsible for the homogeneous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1984

By M. E. Grimes

Rio Algom Mines Ltd. owns eight uranium mines and mills in the Elliot Lake district of Ontario, seven of which were producing before 1960. At present only one mine is operating meeting current contract requirements. Under present economic conditions, it is not feasible to mine ore of less than 2.0 lbs./ton U308, although there are very large reserves below this grade. We are interested in preconcentration for three possible applications: to extend ore reserves by permitting use of lower grade ore, to reduce costs on processing of present grade ore, and to reduce capital investment in expanding production to meet future production goals.

Jan 1, 1973

By Brian Gettinger, Jared Barber, Richard Weatherly, Shannon Dunne, Jeff Masek, Chuck Wolf, Fazle Rabbi, Jack Canfield

During Hurricane Harvey over 60% of the 39 WWTPs, including the low-lying 25 MGD Sims North WWTP, and one third of the 382 lift stations owned and operated by the City of Houston were flooded resulting in extensive facility damage, loss of service and uncontrolled release of untreated wastewater into bayous and creeks. In response, the City has embarked on an effort to improve system resiliency by consolidating at-risk facilities with a network of deep sewer tunnels. These tunnels will provide secondary benefits to the collection system of augmenting the capacity of the existing 6,000 miles of sewer mains and lowering the collection system profile in poor performing areas. Investigations on the cost to mitigate the flood damages by raising the liquid stream processes at the Sims North WWTP is estimated at nearly $450 million. Instead of spending $450 million to raise the plant, the funds will be directed to providing a more robust and resilient wastewater system for the Sims basin area of Houston. The backbone of this new system is a 4.5-mile-long, 110 inch diameter deep gravity sewer tunnel that will convert a system heavily reliant on distributed lift stations to a majority gravity system with a deep consolidated lift station at the Sims South WWTP. This will also allow the City to address the flood prone infrastructure at Sims North and consolidate its operations into a single permitted outfall for this collection system. This approach is the outcome of a team effort focused on maximizing system resiliency and sustainability for the next 100 years. By thinking outside the box, the City of Houston will not only mitigate the flooding risk at Sims North WWTP, but also solve regulatory and operational challenges throughout the sewershed and deliver a winwin on multiple levels.

Jun 13, 2021

By K. Grubaugh

Ghana’s physiographic and geologic features are the basis for its long mining history. The Gold Coast colony has been a significant producer of gold. The gold of the Akan forest (Ghana) was a terminus for caravans that plied Saharan trade routes. Now it also produces significant quantities of manganese, bauxite, and diamonds In addition, the country produces kaolinite, silica for glass, salt, and both aggregate and dimensioned stone. Most secondary minerals are consumed locally but some amounts do find international markets. Ghana revised the mining laws and regulations in 1986. These revised laws dramatically increased gold production and improved the country’s economy. The success of these laws spawned imitators in other African states such as Cote d’Ivoire, Mali, and Burkina Faso. Representatives of these countries claim Ghana was their model. Environmental regulations exist but an intensive adversarial atmosphere is lacking. Ghana has also offered the mining industry incentives like accelerated depreciation rates and exemption from import duties on related supplies and capital equipment. The country has also pursued an aggressive policy to restore the nation’s business infrastructure.

Jan 1, 2001

By A. Habibi

A study has been undertaken on two 1.12 m diameter industrial booster fans operating under different blade settings powered by a 1200 rpm motor at the Missouri University of Science and Technology. The fans total pressure varies up to 1kPa forcingup to 25 m3/s through the workings. A pressure-quantity survey has been conducted inby and outby the booster fans with different blade settings. The study uses a variable speed drive (VFD) to determine the effect of rotational frequency on the system. The pressure drop across the bulkheads has been monitored during the experiments. The fans were operated with various blade settings to determine the optimal scenario that maintains the maximum airflow quantity and the lowest power demand at a particular ventilation station. Five scenarios were conducted with different blade setting and mostly with two different speeds. The experimental results show that alteration of fans? speeds by use of a VFD unit can reduce power consumption while maintaining airflow requirements. With the flow rate forced through the mine by the surface fan the blade settings 4 and 5 were determined as possible alternative for the mine ventilation system. In scenario 4, the airflow at the particular ventilation station for a number of speeds is over 20m3/s. The power consumption at 1080 rpm was measured to be 20.1 kW compared to 25.5 kW at 1200 rpm. The operating cost would be significantly less at lower speeds. Scenario 5 is the alternative making use of both booster fans and the main fan in series that meets the minimum airflow requirement at the particular ventilation station along with minimum power consumption. Reducing both booster fans speeds to 1054 rpm results in power consumption of both together dropping to 11.8 kW. Therefore blade setting 5 using two booster fans was determined to be the optimal setting. Separately it was determined that the combination with use of only one booster fan, the West booster fan, running in series with the main fan is the overall optimal scenario. The power consumption of the West booster fan was calculated to be 8.8 kW at 860 rpm with the minimum airflow requirement being met. Computational fluid dynamics is used for analyzing three dimensional flow structures in time domain and calculating the corresponding unsteady pressure fluctuations. The sliding and dynamic mesh techniques were used to study the unsteady flow interaction arising due to the rotation of the fan blades. The numerical predictions of the variables in the form of velocity vectors and contour plots detailing the flow characteristics are then analyzed according to the known physical situation and existing experimental data.

Feb 27, 2013

Impala Platinum?s No.16 Shaft mine is currently under construction and is expected to reach full production of 256 500 tons per month by 2014. Mining will start at 1 260 m below surface with a maximum mining depth of 1 535 m where virgin rock temperatures of 56.6°C will be experienced. As a result of depth, high virgin rock temperature and narrow reef mining, an expected total of 31.5 MW[R] of air cooling capacity will be required to achieve acceptable underground conditions. This will be achieved by cooling mine intake air in a single dedicated air cooling installation located on surface. The compact installation includes air cooling spray chamber, refrigeration machines, condenser cooling towers, evaporator and condenser water reticulation as well as all electrical and control systems. Construction and commissioning of the first phase of this air cooling installation has recently been completed on a turn-key contract basis.

Jan 1, 2009

By L. Martins

To increase zinc recovery in the concentrate, this investigation performed mineralogical characterization, dispersion studies, bench and pilot-scale flotation experiments and an industrial flotation trial. The objective was to verify the flotation behavior of the silicate zinc ore (calamine type) in the presence of slimes, with the aid of dispersing agents. Characterization studies identified the major minerals in the flotation feed as hemimorphite (calamine), quartz and dolomite. Dispersion tests showed that enhanced dispersion of the particles in the pulp in the absence of reagents occured at a pH range between 8.5 and 12.0. Bench-scale flotation experiments were planned using the statistical tool of complete factorial design at two levels, replicated once. These experiments showed, and were confirmed at the pilot-plant scale, that higher doses of sodium sulfide and polymeric dispersant combined with sodium silicate favored a higher metallurgical recovery. At 6,800 g/t (218 oz/st) sodium sulfide and 6,992 g/t (224 oz/st) polymeric dispersing agent combined with sodium silicate, a zinc grade of 38.4% in the final concentrate was achieved, at an average metallurgical recovery of 72.4%. The industrial trial confirmed the pilot scale results, leading to zinc recovery of 76.1% and a 37.3% zinc grade in the concentrate. Key words: Froth flotation; Flotation reagents; Flotation depressants; Zinc/ zinc ores

Jan 1, 2010

By Hemang Desai

A damaged outlet pipe beneath Lenihan Dam has restricted reservoir discharges, severely constraining the owner?s groundwater recharge program. The solution, a new outlet pipeline through the dam?s right abutment, includes an approximately12.2-m-deep (40-ft-deep) shaft and 618.7-m-long, 4.3-m-diameter (2,030-ft long, 14-ft-diameter) tunnel mined in Franciscan melange composed of hard blocks of rock and soft clayey matrix. Alternating road header with drill and blast operations and using steel ribs and shotcrete have proven a flexible combination for handling the variable ground conditions. Excavating the shaft and connecting it to the tunnel require lowering the reservoir for five months, during which time careful construction sequencing and use of a tunnel plug eliminate the risk of an uncontrolled discharge.

By Jean-Michel M. Rendu

Increasingly, geologists use geostatistical methods to evaluate drilling programs. The complexity of the methods varies with the nature of the available sample information, the objective of the statistical analysis and the geologist's experience. Occasionally, estimating the average sample grade is all that is required. In other instances a semivariogram calculation may be considered. If sufficient data is available, the geologist may wish to estimate blocks or panels of complex shape, using the kriging method of evaluation. Historically, the use of geostatistics by geologists has been limited by a number of factors, most significant being the difficulty in accessing and using computer programs needed to complete the necessary studies. Geologists are often working in remote areas from which electronic communication is unreliable, if not impossible. Even when access to computer programs is technically possible, the costs incurred in accessing and using these programs are often considered prohibitive. In many instances using the programs requires an understanding of computer systems far beyond that which a field geologist can justifiably be interested in acquiring and maintaining.

Jan 1, 1984

By Russell K. McFarland, Eugene L. Foster

INTRODUCTION The U. S. Department of Transportation has underway an important new program which will have a major impact on rapid excavation technology. The Transportation Tunneling Program, as it is called, is a coordinated, multi-modal research and development effort. Its goals, if realized, will significantly improve our ability to build the underground structures needed for transportation. This, in turn, will improve transport efficiency, environmental impact, and the energy consumption associated with the movement of people and goods. Tunneling technology research and development had its beginning at the Department of Transportation in the Office of High Speed Ground Transportation (OHSGT). The OHSGT developed and implemented a program in 1965 to provide the technology for underground construction needed to support future high speed ground transportation. In 1967, when the OHSGT was transferred from the Department of Commerce to the Federal Railroad Administration (FRA), the program accompanied that office. The thrust of the FRA program has been cost reduction through the development of new materials, innovative designs, and better construction methods. During the late 1960's and early 1970's, other developments were underway which would influence the future of tunneling research at the Department of Transportation. An ad hoc

Jan 1, 1974

Power plants that utilize conventional wet flue-gas desulfurization methods produce enormous amounts of flue-gas scrubber sludge. A typical 400 MW power station that burns a high sulfur coal produces 170,000 tons of wet flue-gas scrubber sludge per year. This scrubber sludge is currently landfilled at an enormous cost to utility companies. This material could be used as a raw material for industries that use gypsum, such as the wallboard and plaster industries. However, before it can be used as feedstock for these industries, some of the impurities such as unreacted limestone and silicates must be removed from the scrubber sludge. Froth flotation has tremendous potential for separating these impurities from scrubber sludge. In order to select an optimum flotation process, it is necessary to characterize the surface properties of the major components in the scrubber sludge, which consist of calcium sulfite, calcium sulfate, calcium carbonate (limestone), and silica. In this study zeta potential measurements were used to determine the surface charge of the components in scrubber sludge, with the goal of optimizing a froth flotation process to produce a marketable gypsum product for the wallboard and plaster industries.

Jan 1, 1996