Search Documents

By D. Royston

Gold ores containing antimony suffer from poor recoveries of gold in cyanidation due to the impact of antimony on the cyanidation process. Techniques such as lowering the pH for cyanidation can improve gold recovery, nevertheless a limit can be reached where high cyanide consumption makes traditional processing uneconomic. The paper outlines a process for the pre-treatment of gold-antimony concentrates to remove the antimony resulting in a low-antimony content gold-bearing residue suitable for efficient treatment for gold recovery through cyanidation. This hydrometallurgical process produces a by-product credit of commercial grade antimony trioxide as Senarmontite that can significantly offset the cost of the pre-treatment.

Jan 1, 2007

By A. B. Cecala

An evaluation was recently performed on a district recirculation system at a trona mine in Granger, Wyoming. A 1.52m (5 ft) diameter, 37.3kw (50 hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated approximately 31.4 m'/sec (66,578 ft'/min) of air back into the intake. This amounted to a recirculation factor of approximately 20 pct of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 6l0m (2,000 ft) and 1,829m (6,000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane, and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF. tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1991

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

By Ian McFeat-Smith

Despite a present, short-term economic recession, a remarkable enthusiasm exists in Hong Kong for building infrastructure including major tunnel projects. This paper provides details of current and recent bored tunnel works together with an insight into the impressive list of future underground projects planned by the MTRC,KCRC, Highways Department and Drainage Services Department for the next decade. Risks for each of these works including pipejacking, mixed face and rock tunnelling generally in Hong Kong are also identified. From this is evident that the scale and difficulty of such works continues to increase, requiring the use of more sophisticated methods of construction, the need for better methods of assessing and managing risks and for Government to utilize improved, more equitable Conditions of Contract for such major tunnelling projects.

Jan 1, 2001

By Syd S. Peng

Is the laboratory sized coal specimen much stronger than underground coal pillars? The answer to this question has a profound implication to many coal operators. It will decide how much of the coal reserve can be recovered. Or, in many cases, it will determine whether it can be mined economically. Recent trends in several eastern states to establish regulations regarding coal pillar design to prevent surface subsidence long after mining heighten the debates. And, in some cases, these trends highlight the existing practices that seriously question the conventional wisdom. Currently, nearly all researchers and practitioners agree that as the size of rock specimens increases, its strength decreases. This concept has been universally adopted as the basic principle for coal pillar design in the United States. Several formulas have been derived to account for this effect. The reduction factor for underground coal pillars ranges from one-half to one-sixth of the strength obtained in the laboratory, depending on the formula selected. Recent case studies indicate that the reduction factor is not justifiable, at east in some cases. The use of a reduction factor is based on the assumption hat smaller rock specimens as tested in he laboratory contain none or fewer fractures or planes of weakness than larger specimens or underground coal pillars. In other words, the larger the rock materials, the more fractures it contains and subsequently weaker in strength. Do all underground coal pillars have more fractures than laboratory sized coal specimens? Not necessarily. All coal contains cleats. Some are con¬spicuous but others are not. In terms of cleat density (number of cleats per unit area), there is no difference between an underground coal pillar and a laboratory sized specimen, provided the specimen size is larger than the cleat spacing, which is mostly 25 to 75 mm (1 to 3 in.).

Jan 1, 1993

By R. R. Sacrison

The Barrick Mercur Gold Mine lies in the Oquirrh Mountains of northern Utah. Limestone, sandstone, shale, and chert are the predominant rock types being mined. Recent expansion has encountered rhyolite. Lithology and structural attitudes control most mechanical behavior. Slope steepening, mine planning, and site selection are presented as means by which geological engineering has contributed to the economics of the operation. Geomechanics investments of approximately $700,000 have resulted in cost savings or additional production worth over $16,000,000.

Jan 1, 1990

By Charles B. Dugger

Sacrificial linings for grinding mills have been a necessary state of the art of mineral dressing since the inception of comminution. Long recognized as the final link in energy transmission from power line to ore, mill liners as a scientific endeavor have not expanded as rapidly as other branches of mineral dressing engineering. Several reasons for this technological lag are apparent. Typically in the past, labor intensive foundries were freely located geographically, at a time when transportation charges made up a significant portion of the casting cost. Alloying agents had not gained their current level of sophistication and were relatively inexpensive in the quantities required. Precise foundry controls were not economically justified, or totally understood. Coincidental to these elements, liner consumption per unit processed did not categorically contribute as a major cost item to the mill operator. Grinding equipment was small, and many times lining life exceeded that of the promoter. These unique conditions no longer exist. Ore dressing equipment has grown to meet modern mining demands. Larger processing facilities, utilizing fewer pieces of equipment, have replaced operations of the past. Emphasis today and tomorrow is on larger and larger equipment, with an eye on lower and lower unit processing costs.

Jan 1, 1979

By Brian Fulcher, Matthew Bartlett, Jarrett E. Carlson

This paper discusses the challenges to complete the construction of two large underground Metro stations and connecting tunnels in the Tren Urbano system. The completion work includes the installation of specialized mechanical and electrical systems, extensive architectural finishing as well as coordination with systemwide power and controls installed by others. A unique feature of this project was the simultaneous design and construction of the structural/civil/architectural/mechanical/electrical works by KKZ separately from the power and control systems under the management of the Owner, its consultants and other contractors. Completion of this project comes after almost six years of continuous design and construction in a dense urban environment. The project was confronted by many challenges that could only be met with the combined efforts of the Joint Venture team in close cooperation with the Owner and its System wide Contractor. This paper will also address many of the major design and construction changes implemented to suit the Owner’s requirements.

Jan 1, 2003

By K. R. Griffin

Atmospheric conditions underground are constantly changing and from a safety perspective, it is critical to identify when conditions are trending abnormally. Atmospheric monitoring in underground coal mines allows mine operators to analyze atmospheric conditions underground in real-time. Real-time monitoring can then be used to identify whether atmospheric conditions underground have become problematic. The implementation of a risk assessment and management process allows operators to then use a risk-informed decision making to identify comprehensive site specific ventilation parameters. Establishing risk-informed ventilation parameters and tracking conditions relative to these parameters, management can modify ventilation plans as mine conditions develop to manage evolving risks. Ventilation risk assessment and management allows developing atmospheric monitoring technologies to be fully utilized in order to increase safety standards in the United States. This paper reviews general risk assessment approaches, state of the art ventilation based risk assessment, and the risk assessment and management application within the United States regulatory framework.

Feb 27, 2013

By Thomas H. Ferrigno

Modern Plastics (July, 1983) reported that about 2.2 million tons of mineral fillers were expected to be consumed by the plastics industry that year, of which 7096 was limestone derived. The combination of fillers and polymers is called a composite and, in the more general sense includes continuous and discontinuous components in a matrix. The only significant technical advance in the fillers industry has been the greater general availability of surfied (Ferrigno 1959), an acronym for surface modified, fillers. The many reasons for this occurrence will be given in detail later, but the primary reason lie with differences between inorganic filler surfaces and the polymers which bind them together to form the composite. Minerals and glasses (fiberglass, fly-ash and beads) have surface tensions in excess of 200 dynes/cm, whereas organic materials have surface tensions less than 75 dynes cm. Water has a surface tension of 72 dynes/cm and is always present as an absorbed layer on high surface tension materials to reduce the surface tension. Although almost any organic liquid or polymer has a surface tension low enough to displace the water layer, the highly polar nature of filler surfaces requires highly polar agents to produce a permanent effect, and frequently the water is so tightly bonded or so much more active that the displacement is temporary. Furthermore; the water layer causes tiny particles to adhere to each other (agglomerate) to make sepaartion or dispersion of the individual particles very difficult. The solution to these problems is then to form a chemically bonded layer on the filler surface similar to that of the polymer so that immediate wetting, dispersion and uniform distribution of the filler particles is obtained.

Jan 1, 1985

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

 The paper combines theoretical and experimental analysis to improve the accuracy of predicting paste yield stress by slump flow. It derives an analytical model of slump flow for yield stress, providing a theoretical basis for quantifying the rheological properties of paste with slump flow. The study uses three different tailings-prepared pastes and constructs an empirical yield stress model, showing high accuracy and good generality.

Aug 1, 2023

By Roger K. McLimans, Venkatramaiah N. Vasudev, Christian Knudsen, Stefan Bernstein, Dirk Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) analyses of sediment samples from coastal regions of Kerala and Tamil Nadu states and the heavy mineral deposits of Chavara, South India, show large lateral differences in the titanium content in ilmenite due to varying degrees of iron leaching. As the depositional environments for the sands with varying degrees of ilmenite alteration are comparable, the cause for the different degree of alteration is due to differences in the primary source of the ilmenite or to differences in the geochemical history of the ilmenite grains during transport from source to deposit. The CCSEM analyses of the heavy mineral fractions show that source of sediments with a high content of titanium-enriched ilmenites, mainly the heavy mineral deposit around Chavara, resides in the khondalite belt of South India (granulite facies metasediments). The less titanium-enriched ilmenites are sourced from other rocks in the area such as the charnokites. Those conclusions are based on the high MgO content in the leached ilmenites, chemical composition of the accompanying garnets (low CaO and high MgO), and the concentration of aluminum-rich minerals in the sands.

Jan 1, 2005

By J. B. Moritz

From the beginning, man has concerned himself with the task of controlling the elements and forces about him so as to provide a better and easier life. In the accomplishment of this task, he is required to utilize in the best way possible the resources which are available to him. In many cases, the available resources must bee refined before they are in a useable form. Many products in the mining industry fall into this category, as some form of refinement is generally needed to produce a saleable product. Over the years man developed more efficient ways of extracting the resources from earth through the use of electrical and mechanical devices. A reduction in manual labor, which is a by-product of increased efficiency through machines, has also been enjoyed. The combination of man's senses and new devices has also enabled man to reach a high level of control in the refinement process. Control of a process through machinery and man's senses has been termed an "art." Until recently man's senses (sight, feel) were the only method available for making measurements simply because suitable measurement devices (instruments) were not available. Even today some items cannot be measured and man's senses must be used. However, the development in our instrument laboratories tends to indicate that time will eliminate this. In recent years, control of many processes has been reduced to a science and part or all of the art eliminated. This does not imply that process art should be degraded; however, when a process is reduced to a science, uniformity of the product from day to day is attained. Decreased processing time and more efficient use of additives and raw materials are other benefits that result from control of a process when it is reduced to a science.

Jan 1, 1965

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By S. J. Neethling

The flotation froth structure and motion determines the amount of entrained gangue that is collected to the concentrate. Despite this important role in the overall performance, the behaviour of the froth is still ill understood. To date, predominantly empirical models have been developed to describe entrainment. A fundamentally based model is described and used here in an attempt to improve the understanding of entrainment. This general froth simulator (UMIST FrothSim) allows the modelling of a wide range of flotation conditions, as it takes account of a large number of the physical phenomena that occur within flotation froths. The model firstly describes gas motion and bubble coalescence, and the water motion based on gravitational, viscous and capillary effects. The motion of the solids distinguishes between various solids classes based on hydrophobicity, particle size and density and models them by including the effects of Geometric and Plateau border dispersion, particle settling and the motion of the water. The aim of this paper is to show the applicability of this model to explain the observed entrainment and collection of gangue. This is done by comparing model predictions with the experimentally observed relationship between the gangue and water recoveries. The model predicts the identical trends, which are explained in terms of the interaction between the linear effects of water motion and hindered settling and the non-linear effect of particle dispersion.

Jan 1, 2001

By David Van Horsen

Operation and maintenance of California?s water tunnels is an important factor and vital link in California?s infrastructure. These tunnels are owned and operated by a variety of large and small private and public water and power utility companies, municipal agencies, and irrigation districts. Visionary pioneers such as Michael O?Shaughnessy (San Francisco Hetch Hetchy Water Supply System), William Mulholland (Los Angeles Department of Water and Power and Metropolitan Water District of Southern California?s Colorado River Aqueduct), and John Eastwood (Southern California Edison Big Creek Hydroelectric Project) built large and small water supply, irrigation and hydroelectric tunnels, which have supplied environmentally friendly-water supply, renewable electricity, and uninterrupted service to a burgeoning population and economy. This paper introduces these pioneers and describes several case histories and lessons learned during condition assessment and rehabilitation of tunnels providing enlightenment of California?s vital water projects.

Jan 1, 2008

By Spencer R. Titley

Porphyry copper deposits in the southwestern Pacific area represent relative newcomers to the growing number of occurrences of this mineral deposit type. In addition to firmly establishing the importance of this region and its potential influence within the framework of world copper resources, the deposits of this region are significant from a scientific point of view because of their close relationship to the phenomena of Island Arc evolution. Since the discovery of Panguna on Bougainville in 1964, the list of prospects, proven and unproven, and developments, has grown to more than twenty and the number continues to increase. At the time of this writing, the number of prospects is imperfectly known but the following localities and numbers are fair minimum approximations: Manus (Admiralty Islands) (3); New Britain (5); New Ireland (1); Guadalcanal (2); New Guinea Highlands (6); Misima (1); and Fiji (2); Proven prospects are present in the new Guinea Highlands (2); one deposit is being developed in Test Irian, and one orebody, on Bougainville, is in production. This summary paper concerns a discussion of some of the geological characteristics of producers, developments, and prospects on the Islands of Nets Guinea, New Britain, Bougainville, Guadalcanal, and Manus. I am not aware of publishable data for Misima or Fiji. As so many variables ultimately determine whether or not a porphyry copper occurrence becomes an orebody, not the least of which is geography, this summary treats the characteristics of these occurrences which alloy; their assignment to the porphyry copper category. For purposes of this discussion, I have considered those copper occurrences which are apparently genetically related to talc-alkaline intrusions and in which the content of copper has been upgraded 50 to 100 times the Clarke for that particular host rock. Some of these occurrences are shown on Figure 1.

Jan 1, 1973

By Rubén Pavón] [H.

Mexico, that for various years held the second place among the elemental sulphur producers in the world, now occupies the fourth position. Nevertheless, taking advantage of the recent increase in the international prices of the metalloid, it is expected that Mexico recovers its traditional position producing, for the first time, over two million tons of sulphur during 1974. Drawing from material stockpiled during the last years sales are expected to reach 2.5 million tons, at excellent prices in the foreign markets, but not so in the domestic ones where prices have remained practically static since 1955, in spite of substantial escalation of production costs. Of the two sources of elemental sulphur in Mexico, the frasch process extraction from the salt domes of the Tehuantepec isthmus where the most important reserves are located - is the one that shall have an important increment. An increase of production of lesser magnitude is expected from sour gas, since sulphur recovery plants wilI go on stream toward the end of the year in the new oil fields recently located in the State of Chiapas. Two Mexican corporations are expanding and improving rational Frasch extraction operations. Together with Petroleos Mexicanos' sulphur recovery from sour gas it is estimated that production during 1975 shall reach 2.5 million tons and, consequently, supply the domestic market and generate an important sum of foreign currencies.

Jan 1, 1974

By Z. Hyder

Simulation and modeling is powerful tool to analyze real time data and can be used to analyze different scenarios using appropriate software that may reduce need of infield data collection process and can predict reasonably accurate results. In this paper the real time data of a mine is used to simulate and model the stresses on the pillars and evaluate the pillar strength and safety factor. The material properties assigned to the model are obtained by testing the representative samples taken from the selected locations of the mine. The mine under investigation has 50 ft wide pillars and 50 ft wide rooms under an average overburden of 650 feet. The effect of reduced pillar dimensions and increased roof span on overall stability of mine and extraction ratio is analyzed using LaModel [1] software. The predicted results of the reducing pillar size are analyzed to compares the current mining practices with the optimized room and pillar size to get better extraction ratio without comprising the safety.

Jan 1, 2011

By Gerald C. Smith

Carlin Gold Mining Company is a wholly owned subsidiary of Newmont Mining Corporation and is located 76 kilometers north west of Elko, Nevada. Multiple bench open pit mining methods are being used to mine 24.5 Mt of ore and waste per year. Mining started in 1964 and up through 1983 Carlin has mined 138 Mt of ore and waste and has milled 13.8 Mt of ore. Selective mining of carbonaceous and oxide ores together with a good grade control program have been key factors in the success of the operation. This paper will present the raining methods and the mining equipment being utilized to make Carlin Gold Mining Company a very profitable operation while mining and milling low-grade gold ore.

Jan 1, 1985