Search Documents

By Jeffery L. Kohler

The research and development of a pattern recognition system which can predict incipient failures and safety hazards in the mine power network is described. An examination of mine electrical safety hazards revealed they are often related to the electrical equipment down-time experienced on mine sections. Based on this, a method is proposed that can improve both production and safety, without compromising either. Equipment failure modes are examined to illustrate how the ultimate failure can be predicted for enough in advance to allow a convenient and safe repair, followed by a discussion of actual monitoring system performance. Finally, the paper is concluded by projections of the system's utility to industry.

Jan 1, 1977

By C. D. Buttgereit

A variety of mathematical techniques are available in the pertinent literature concerning the interpretation and reduction of aeromagnetic data. The quantitative methods applicable to this data en¬compass a wide spectrum including filtering, continuation, derivatives, reduction to the poles, spectral analysis, and "undraping" of flight line data. With the aid of the digital computer, the techniques listed, and others, can be computationally performed on a gridded data set. In addition, current sophisticated computer hardware permits the systems analyst greater latitude in the storage and retrieval of data and in the display of resultant naps on a digital x-y plotter than previously available. Although many interpretive techniques concerning magnetic data have been published and computer machinery has been on the market, little has been written incorporating both disciplines into a unified digital processing system. In the present paper, a general purpose system in given which in designed for routine use in the interpretation of aeromagnetic (and other potential field, etc.) maps.

Jan 1, 1970

By Ching-Yi Tsai

The effect of various constituents on the pyrolysis and combustion of a pulverized coal in an entrained-flow reactor has been inves¬tigated. Predicted time-temperature histories of the coal' particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm. This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate prior to ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of a HVA bituminous coal which were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite rich samples.

Jan 1, 1984

By M. T. Atwood

For more than sixty years the rich oil shale formations of Colorado, Utah and Wyoming have been evaluated as a future source of petroleum. After many false starts the commercial production of shale oil is near. Union Oil and Colony (Exxon and Tosco) have begun construction of commercial plants. Occidental and Rio Blanco (Gulf and Standard of Indiana) are well along in the development of modified in situ (underground) processes. A number of other companies and groups are in advanced stages of development. This paper will review some of the major elements involved in the production of shale oil with emphasis on means available to express the efficiency of production of pyrolysis liquids and gases from oil shale rock.

Jan 1, 1982

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13' x 12' overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

By K. R. Weller, U. J. Sterns

The goal of most in-plant studies is to identify factors that limit overall plant performance. A major finding from such studies is that interactions between unit operations are always important, usually specific for a particular ore and plant combination, and are one of the limits to plant performance. Computer simulation based on process models developed from in-plant studies is a useful tool for identifying limits to performance and for estimating the effects of proposed changes at both pilot and industrial plant scales. Examples involving interactions between comminution and various separation and agglomeration processes are presented, and directions for future development discussed.

Jan 1, 1989

By J. D. Miller, C. L. Lin, J. Dong

Nano clay mineral particles such as kaolinite — with primary particles typically smaller than 2 μm in size — can cause significant problems in flotation processes and tailings disposal, including the processing of Florida phosphate rock and Canadian oil sands. In this study, the consolidated state of flocculated kaolinite sediment was examined, and high-resolution X-ray microtomography (HRXMT) was applied to describe the structure of the consolidated sediment. Using this tomographic information, the complex geometry of the channel network structure for the consolidated flocs was established for the first time. With the establishment of the experimental channel network structure, permeabilities were estimated by flow simulation using the Lattice Boltzmann method. Results for kaolinite sediment with and without polymer are compared and discussed. Results for flocculated kaolinite sediment in a gravitational field are also presented and discussed. The results show that as polymer dosage increases, the permeability of flocculated kaolinite sediment increases, and as suspension pH increases, the permeability of flocculated kaolinite sediment decreases.

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By Thomas P. Meloy

There is much interest in the automation of entire comminution circuits, At the present technological level it is possible to automate a circuit but to date it has not been done, To successfully automate a circuit, a number of problems must be solved. Not all of them are engineering problems. The purpose of this paper is to discuss some of these problems, as certain the implications of these problems and indicate solutions to them. In this paper the term "automation" is used loosely but in the popular sense. Namely, that a plant is automated if a computer is used to control the basic flow of the materials as well as setting the critical parameters in the process. Specifically, the discussion will concern itself with the control of comminution circuits from the dumping of the ore into the primary crusher until the final interface between the comminution circuit and say, the flotation mill in the case of a sulfide ore.

Jan 1, 1965

By J. Best, K. Gallant

This paper explores the age-old concept of mine-mill reconciliation from a new perspective. Advances in reconciliation processes have been slow to materialize because in the quest for “rightness”, engineers, geologists and metallurgists have become entrenched in their viewpoints, dutifully performing to the metrics and expectations imposed upon them by the siloed organization. Moreover, reconciliation has not been viewed as a primary value creator, but an accounting non-value added task. In reality, the knowledge from reconciliation can significantly enhance yields. Critical review of the direct variables (tons, grade, etc.) and other less-obvious variables (incentives, communication, etc.) reveal a complex web of barriers to be cleared by management in order to realize benefits. Also, mineralogical reconciliation methods may offer renewed faith in the process.

Jan 1, 2004

According to the Balandin's (1) "multiplet theory of catalysis", adsorption can occur only if atoms of the reactant molecules are congruent with surface atoms of the catalyst. Such a condition calls for certain definite geometrical relationships between the reactant molecules and the atoms at the surface of the catalyst. If such a match or geometrical 'fit' is not provided, the surface reaction will not take place. An appropriate analogy to this may be the lock and key theory that enzymes should fit a substrate just as a key fits a lock. Similar geometrical considerations in adsorption studies were made in connection with the flotation of minerals. Gaudin(2) and Gaudin and Preller (3) proposed that if the dimensions of collector ions are in registry with the mineral lattice, an ordered layer of adsorbed species is formed. They explained that the structural fit is one reason for good flotation of galena with xanthate. In another study, Bachmann (4) attributed the selective flotation of KC1 from NaCl with amine to the fact that the lattice parameter of the amine collector is closer to that of KC1. Schubert(5) investigated the flotation of various nonmetallic minerals with amine and pyridine, and related the dimensions of the collector ions with the anion distances of the mineral surface. He concluded that good flotation is obtained when the tolerance is within 20%. The geometrical theory has also been used by Groszek (6) to explain the preferential adsorption of n-paraffin onto the basal plane of graphite. The geometrical theory has thus been found useful in explaining adsorptive properties of an adsorbate relative to the substrate structure. The purpose of the present work is to examine the possibilities of a geometrical fit between sodium dodecyl sulfate and Cu(OH)2 surface, and to construct a crystallographic model of the surface compound.

Jan 1, 1974

By P. Zhu

The leaching behavior of copper powders recovered from waste printed circuit boards (WPCBs) was investigated using electrogenerated chlorine and aeration in a sulfuric acid solution with added NaCl and CuSO4. Various parameters were studied to understand the mechanism of the copper leaching. When the current density increased from 0 to 0.1 A/cm2, the temperature from 30 to 60° C, agitation speed from 100 to 400 rpm, and the size ranged from below 75 to 150 µm, the leaching ratios of copper powders increased. The leaching kinetics were analyzed using a shrinking core model: 1-(1-X)1/3 = kt, and the leaching process was chemically controlled with an activation energy of 14.7 kJ/mol due to Cl- ion catalysis. The ratios of [Cu+]/[Cu2+] at various temperatures (30, 40, 50, 60 and 70° C) showed a periodic variation with the increasing of the leaching time. The redox potentials of the leaching solution and copper leaching ratios in different conditions were measured. The result indicates that dissolved oxygen achieved the dissolution of coppers and electrogenerated chlorine can promote the dissolution of copper powders and improve the reaction rate of kinetics in the presence of oxygen.

By R. Shields

"Hard rock mines move large volumes of material. But the conveyors essential to this movement suffer lots of problems, including carryback, spillage, dust, and belt wander. Many of these issues are created at the transfer points where the belts are loaded. This presentation will start with an overview of the latest transfer point systems that incorporate safety and serviceability by design. It will then report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, Nevada. Here performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine. THE IMPORTANCE OF TRANSFER POINTS Conveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance are the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created. The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material—cargo released in the form of carryback, spillage, or airborne dust—that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems, and issues with community relations. As estimate attributed to the U.S. Mine Safety and Health Administration (MSHA) notes that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points. TECHNOLOGIES TO IMPROVE TRANSFER POINTS A number of techniques to improve the performance of conveyor transfer points have been developed. They include: • Absorbing impact, to prevent damage to belt, belt support systems, and conveyor structure, and reduce spillage caused by the impact energy arising from long material drops or large lumps of material loaded onto the receiving belt. • Stabilizing the belt line, to eliminate sag that allows spillage and encourages material entrapment that can damage the belt. • Protecting the skirtboard seals, by sheltering the sealing strips from the mass of cargo pushing material toward the edges of the belt. • Using self-adjusting, multiple-barrier edge seals, to keep material on the belt by providing long-lived seal efficiency with minimum maintenance requirements. • Controlling and centering the belt’s path, to eliminate belt wander and the spillage and damage it can cause. • Allowing dust to settle, through the incorporation of chutework that provides expanded stilling zone and the use of dust curtains at the points where the belt enters and exits the transfer. • Adding supplemental dust control systems, through the installation of systems for passive dust gathering, water-based dust suppression, and/or active dust collection."

Jan 1, 2017

By R. Lai

This paper describes the application of a cyclonic flotation column (CFC) for coal cleaning. A CFC makes use of centrifugal force to create a density gradient in a column to augment the froth flotation process. In a CFC, a series of angular helical inserts is attached to the wall of a conventional column and coal slurry is mixed with a series of impellers attached to a central shaft. The hydrophobic froth concentrates near the center shaft and moves upward, while the relatively heavy hydrophilic particles concentrate near the wall and are guided downward by the helical inserts. Results of pyritic sulfur removal from an Upper Freeport coal during CFC flotation are discussed in this paper.

Jan 1, 2000

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

By Robert R. Munro

Traditional aggregate sources, that is the riverbeds, the alluvial fans, located relatively close to the developing urban centers are being foreclosed to mining. As the sand and gravel reserves are depleted, those production plants are unable to secure additional adjacent reserves and are being forced to close down. The sand and gravel industry, in many respects, is its own worst enemy. We promote development, we promote the paving of streets, the building of houses, and industrial and commercial centers, and because of economics, we tend to favor those developments located close to our operations. Thus, we encourage development by our neighbors who soon become our detractors. In general, urban development is not compatible with sand and gravel mining. The neighbors don't like the view of the pits or the quarries, they complain about the "dust", about noise, about trucking . . . in general, the neighbors are not happy being close to an aggregate source.

Jan 1, 1984

By C. T. Aimone-Martin

Time-domain reflectometry (TDR) laboratory experiments have been conducted using cylindrical salt cores from the Waste Isolation Pilot Project (WIPP). TDR has been used as an instrumentation technique to quantify the type and magnitude of rock mass deformation. Laboratory shear and tensile tests were conducted to calibrate measured deformation versus changes in reflected waveforms. Coaxial cables grouted within rock cores were crimped to produce localized reference defects. The evaluation of waveform characteristics produced during rock deformation experiments shows a good correlation of cable response to both shear and extension of the salt

Jan 1, 1994

By Oleg N. Tikhonov

A new extraction method which includes a combination of gravity and alternating electromagnetic fields with interfriction of mineral particles was proposed (Tikhonov O.N., 1979) and tested in lab conditions at Mineral Processing Department of St. Petersburg Mining Institute. At the beginning of the work the main goal was to find an efficient alternative to traditional extraction methods (like shaking table, etc.) used for concentration of fine alluvial gold particles. After the method and a series of gradually improved lab separators (Tikhonov, et al., 1983) were positively tested for gold (Tikhonov, et al.. 1986) the efficiency of the method was also proved for extraction of and other heavy minerals from alluvial and ground ores in experimental work at the St. Petersburg Mining Institute. The fine heavy minerals were separated to concentrates with high technological indices (Andreev et al., 1987), (Tikhonov, Gladkov, 1987), (Tikhonov, Gladkov 1989). In parallel a semi-industrial gravi-electro- magnetic separator was made and several technological flowsheets were designed for testing the method in industrial conditions (Tikhonov O.N., Miazin B.N., 1987), (Tikhonov O.N., Tolstunov S.A., Jebelev V.V.,1989). A series of industrial tests accompanied with complete sampling and standard technological measurements were performed at several alluvial deposits, with good technological indices. Thus the method and the flowsheets displayed high additional recovery of fine alluvial gold particles during elkrated industrial experiments in Siberia (Aldan province). At higher concentrate grade this method, even in one-stage operation, increased gold recovery more than by 25% compared with shaking table (for particles -0.10 mm gold recovery was 82% vs. 55% by shaking table, for particles - 0.25mm the recovery was 97.5% vs. 61.8%). Experiments were performed by joint team of St. Petersburg Mining Institute and the Irkutsk Institute of Rare Metals (Tikhonov O.N., Gladkov S.A., Tarasova T.B., 1991).

Jan 1, 1995

By J. A. Slattery, C. E. T. White

Although trace amounts of Indium are found in many ores, commercial production of the metal has come almost exclusively from residues, flue dusts and slags generated by Zinc recovery operations. Our paper attempts to summarize the various approaches used to recover Indium from these by-products. Some comments on production and price trends are Included as well as our views on future availability.

Jan 1, 1983

By N. T. Cowper

Slurry viscosity ultimately affects the majority of mineral extraction processes. However, to date its role has been disguised because mineral processing equipment has been conservatively designed to operate at minimal slurry viscosity. With most ores this still meant acceptable solids concentration was achieved. However, with the advent of treatment of weathered ores the resulting higher slurry viscosity (rheology) has meant solids concentration has had to be reduced, often to unacceptable levels. To permit operation at higher solids concentration chemical dispersants are employed. These dispersants are expensive and their addition should be controlled. Slurry Systems Pty Limited (SSPL) has developed an On-Line Viscometer to monitor and control slurry viscosity, whether by controlling water addition or by controlling dispersant addition. Using this instrument the slurry rheology can be controlled at the optimum level, maximizing solids throughput, and minimizing water, reagent, and dispersant addition. This paper discusses rheology of typical mineral slurries, the relationship between slurry rheology and percent solids in a slurry, and the need for rheological control in mineral processing. The effects of rheology on various process steps, and the use of dispersants are reviewed. The paper concludes with summarizing actual case histories and cost impact of Theological control.

Jan 1, 1992