Search Documents

By J. K. Horbaczewski

The reclamation of an open dragline pit (Pond A3P-2) at the Gibbons Creek lignite mine in east-central Texas required neutralization of acid mine pit water. At the start of treatment with hydrated lime (Ca(OH)2) on March 28, 2000, the pond had partially filled with 913,000 m3 (740 acre ft) of pH 4.9 water. Another 666,600 m3 (540 acre ft) of pH 3.3 water was pumped in from an adjacent pit (PitA3P- 1). By the end of the project (July 5, 2000), a combined volume of 1,579,000m3(1,280ac-ft or 417milliongal) in PondA3P-2 had been successfully treated to pH 8.2 with 431 t (475 st) of lime. This was two to three times more neutralizer than laboratory trials and detailed chemical titration had predicted. The main reasons for the difference are thought to be the inadequate representation in a laboratory setting of some of the chemical reactions that occurred in the field, including incomplete mixing of reactants, reactions with clay minerals in the pit walls, the kinetics of biologically-mediated reactions and the kinetics of aluminum oxyhydroxide polymerization (aging).

Jan 1, 2002

By Iwasaki I.

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates, and the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when anionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were most strongly affected by the level of starch, to a lesser degree by the pH, and were virtually independent of the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semi-taconite could be readily attained with starch and calcium chloride.

Jan 1, 1968

By M. J. Ross, D. A. Norrgran, J. A. Wernham, J. N. Orlich

INTRODUCTION Laboratory testing for magnetic concentration circuit design is a requirement, just as it is for most other types of concentration. Natural variations in raw materials allow on1 y the broadest of generalities to be made regarding magnetic separation. Further, magnetic fields are geometry dependent, leaving fundamental models of a separator overly dependent upon the exact conditions for which the models were derived. Despite this, an understanding of the basics of magnetic separation and of the problem to be attacked can result in rapid progress towards the final circuit design with a relatively simple testing program. Magnetic Separation Basic Principles A magnetic field can readily be understood in terms of lines of flux. A familiar demonstration of these lines of flux is the pattern of iron filings on a sheet of paper when a magnet is placed underneath. Lines of flux2 are measured in Gauss (1 line/cm2) or Tesla (10000 gauss). Regions of high field strength have a greater number of lines. Field direction is indicated by a convergence of lines. When a particle is placed in a magnetic field it cuts the lines of flux and alters them in one of three basic patterns. These patterns are referred to as diamagnetic, paramagnetic and ferromagnetic. Diamagnetic materials have electronic structures which react to oppose an applied magnetic field. This opposition acts to locally reduce the applied field slightly. The visualization is that lines of flux diverge and go around the particle. Because of this divergence or opposition, a diamagnetic particle will tend to move towards regions of lower flux density. That is to say that the particle will be repelled by a magnetic field. Aluminum oxide and napthalene are examples of diamagnetic materials. Paramagnetic materials have an electronic structure which increases an applied magnetic field. Although these materials also exhibit diamagnetism, they have randomly oriented impaired electrons which align with the magnetic field. The resultant local field enhancement is significantly larger than the diamagnetic opposition. The visual-

Jan 1, 1986

By Ray E. Williamson

One of the prime objectives of the mine industry is to develop a low cost way to clean up what has been called "The Rape Of Mother Nature". The project falls under the broad umbrella of reclamation, which is now considered an essential part of the mining cycle. As such, it is being given full consideration in the initial planning of all surface operations. In most areas, if a proposed mining system does not lend itself to proper reclamation, it is not an acceptable system. By combining mining and reclamation plans, a producer not only can minimize reclamation costs, but can also restore the land to usefulness and insure continuing profits after a deposit is depleted. As long as fifteen years ago, many of the larger mining companies were already deeply involved in this extra cost work. Even then the involved companies were projecting a great need for a bigger bulldozer, Bigger than anything commercially available. At that time, the D9 tractor weighed about 60,000# bare weight.

Jan 1, 1975

By O. Lopez

"Stringent regulations and increased arsenic presence in ore bodies being exploited have created the need for cost effective and environmentally compliant technologies to remove selenium and arsenic from mine waters and metallurgical waste streams. Existing treatment methods have high life cycle costs and/or produce residues that, due to their unknown stability over the long-term, may represent future liabilities. This results in high compliance costs and uncertainties which negatively impact existing operations and projects in permitting. Selen-IX™ is a new ion exchange based process that selectively removes selenium from mine impacted waters down to 1 ppb while producing a stable inorganic iron-selenium product. Results of piloting completed on streams generated from coal and copper-gold deposits are presented along with preliminary equipment sizing and life cycle costs of full scale treatment. An example of a commercially available system for arsenic removal using sulphide precipitation is presented. The benefit of this treatment method is discussed based on recently completed technical feasibility assessment including laboratory testing and preliminary engineering design. INTRODUCTION Selenium Due to the chemical similarity between selenium and sulfur, selenium substitutes sulfur in many minerals that can be found in a wide range of deposits including coal, base metal, precious metal, phosphate, and uranium. One of the main environmental challenges facing the industry in North America today is related to the removal of hexavalent selenium, e.g. selenate, to ultralow levels, typically between 1 to 10 ppb, from large flows of often cold water containing less than 1,000 ppb of selenium. Recent studies commissioned by the industry identified biological selenium reduction systems as the best available technology. Although the biological selenium reduction process is commercially proven in certain applications to remove selenium to ultralow discharge levels, the technology has been primarily applied to relatively low and constant flows of warm water produced by the Flue Gas Desulfurization (FGD) scrubbers in the power generation industry. The wide spread adoption of this treatment method by the mining industry is hindered by high capital and operating costs associated with treating large flows of cold water, lack of data and knowledge about the long term stability of solid residues produced by this treatment, and limited capacity of biological systems to respond to sudden changes in flow and/or mass load of contaminants. Furthermore, it has been reported that reaching discharge limits less than 3 ppb could be a challenge and that polishing treatment for the removal of BOD and phosphate maybe required to avoid the impact of the biological treatment which requires organics and nutrients, on aquatic environment downstream of treatment plants. Alternate treatment systems are being developed to overcome and/or completely avoid some of the challenges of biological systems. One such treatment system is BioteQ’s Selen-IX™ process which is purely physico-chemical treatment system."

Jan 1, 2015

By Todd Minoski, KRISTIN FLOYD, Michael Murphy, VASU GANGRADE, Gamal Rashed, DYKE MARK VAN, Brent Slaker

Underground stone mines frequently operate on multiple mining horizons or are required to undermine or overmine old workings. In these situations, the effects of pillar columnization and interburden thickness on the stresses surrounding mine workings are poorly understood. Many old workings were not designed to consider the effect on future undermining or overmining and, as a result, are laid out on irregular patterns and with pillar sizes that are difficult or impossible to replicate on adjacent levels. Additionally, as depth increases, even a consistent gridded mine layout may result in poor columnization due to the need to increase pillar sizes. Rules of thumb and past practice for designing multiple levels may often be effective. This paper explores the effect that multiple-level stone mining has on stress redistribution through the discussion of two case-study mines and associated numerical modeling to provide additional insight into situations which may cause concern.

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet's size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By R. B. Krog

The use of belt air as an intake source at longwall operations has changed greatly over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors, including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different than for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with the belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2010

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By Musa D. Manzi, Raymond J. Durrheim, Richard T. Masethe

Large mining-induced seismic events and their aftershocks cause hazardous working conditions, damage infrastructure, delay production and pose a risk to miners in the deep-level gold mines of South Africa. Stress changes affecting pre-existing zones of weakness are the main drivers of large mining-induced seismic events, which are often followed by aftershocks triggered by quasi-static stress transfer within the rockmass. A better understanding of seismic source mechanisms is important if the seismic data is to be used more effectively for mine planning and to reduce the rockburst risk. Four large seismic events (ML≥2.0) associated with the mining of the Ventersdorp Contact Reef (VCR) at Kloof Gold Mine occurred on 13 June 2017. The events and their fore- and aftershocks were studied in detail to establish the circumstances and the cause of the incidents. The local magnitudes ranged from ML 2.3 to ML 3.0, the seismic moment from 0.69 to 2.25 x 1013 Nm and the source radius from 92 – 150 m. The main shocks were preceded by foreshock sequences, which were especially vigorous in the four hours before the main shock. Seismicity was recorded by in-mine arrays of three-component 4.5Hz geophones (detection threshold approx. ML -2.9). Following all four main seismic events, ML 2.3, ML 2.3, ML 2.9 and ML 3.0, the network detected a total number of 300 aftershocks ranging from ML -2.9 to ML 1.6 spread within a 1300 m radius from the centre of the seismic network. The statistical properties of the aftershocks were analysed using three scaling relationships: (i) Gutenberg–Richter frequency magnitude relationship; (ii) modified Omori’s law; and (iii) Båth’s law for the magnitude of the largest aftershock. The geological or mining feature that controlled the failure (e.g., fault, dyke, pillar, abutment) was determined by calculating the orientation of the nodal planes of the large seismic events using moment tensor analysis and studying the aftershock distributions.

Apr 26, 2022

By George H. K. Schenck

The North American-based mining engineer needs to understand the differences that exist between mechanical mining or boring machines built on this continent and those built in Europe. The differences Ere most clearly seen when machines for large-sized openings--about 15 feet high-are considered. This report will focus on the innovations of European origin. The rock-breaking tool, drag bit, or roller cone that is efficient for a particular project is related directly to the strength of the rock involved. This strength is generally stated in reference to the rock's unconfined compressivee strength in pounds per square inch (psi) although it is well recognized that a rock's shear strength is also important. Compressive strength has been adopted because it is simple to test for and provides a convenient comparison. Table 1 relates cutter type to compressive strength and indicates the general nature of the machine innovation devel¬oped in Europe.

Jan 1, 1970

By E. Pizarro

Division Andina has considered in its long range planning, the exploitation by panel caving method of "Third Panel" mine, which was started its production stage during the second half of 1995. This mine has two production levels, the first is grizzly level and another is L.H.D. level. Both sectors use the same haulage level where mineral is recollected through ore pass. For mineral loading and haulage its use 50ton diesel trucks combined with electro-hydraulic chutes. The automation has permitted what this operation is carrying out with remote control by driver's truck, in concordance to short range planning.

Jan 1, 1998

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

By Richard E. Gray

Virtually all structures show some signs of distress due to deterioration of the building components, to changed loads, or to changed support conditions. Changed support conditions result from ground movements. In mining regions many cases of structural distress are attributed to mining without considering alternative causes. This is particularly true of coal mining since it occurs under extensive areas. Coal mining is estimated to have already undermined more than eight million acres and may eventually undermine 40 million acres in the United States (HRB Singer, Inc., 1977). Other nonmetal and metal underground mines impact much smaller areas. Although it is sometimes difficult, even with careful study, to identify the actual cause of damage, persons responsible for underground coal mining should at least be aware of possible causes of building stress other than mine subsidence. This paper presents information on distress to structures and briefly reviews a number of causes of ground movements other than subsidence: Mass movements, dissolution, erosion, frost action, shrinking and swelling, yield into excavations and compressibility

Jan 1, 1986

By E. Lovera

Social attention to environmental aspects, steadily increasing in European Countries, has been leading to a stricter regulation of many productive activities. Among them, mining and quarrying sectors have been often censured for their potential and real impacts on land and environment. Referring to dimension stone exploitation (also the terms ornamental stone or natural stone are here used as synonymous), quarries are often concentrated in extractive basins, where the resource is localized with suitable quality and quantity: this fact has sometimes raised critical environmental situations. Nevertheless, dimension stone quarrying represents in Europe a traditional and important economical activity, source of wealth and employment. Moreover, many natural stones take on a ?cultural? value and may be considered as ?classic?, as they have been exploited since antiquity and are element of the architectural heritage of many Countries. The sector relevance demands the research of a sustainable balance between social-economical needs and environmental protection. Actually, very restrictive environmental protection policies have led to severe limitations to quarrying activity, but the results do not seem to be completely positive in terms of sustainability: on the one hand, closing-down stone quarrying activities imposes a shrinkage in local, social and economical development; on the other, quarrying activity is pushed towards developing Countries, environmentally un-protected, simply moving and putting off to next future the problem. The challenge of the sustainable development of quarrying sector ? recently explored in the European Commission?s communication ?Promoting sustainable development in the EU non energy extractive industry? (COM-2000-265) ? should be achieved through a positive link between theoretical statements and practical effects: sustainability indicators may be an effective instrument to assess and monitor the environmental performance of the industry. The paper refers to the development of specific ecological criteria and indicators, which can be useful to measure and predict the eco-efficiency of a dimension stone quarry, finally pointing out where improvement efforts have to be focused.

Jan 1, 2003

By R. Scheffel, R. Washnock, G. Zarate

"The second survey of global copper leaching operations has been completed, the data published in 1998 has been updated. A survey questionnaire was sent to 40 identified copper leach operations around the world including those leach properties still in operation that responded to the 1998 survey. This paper lists the results of 26 operations that responded to the survey. Selected information from the survey is represented in graphical form. INTRODUCTION Copper leaching was first performed by truck dumping huge monolithic stockpiles of ore and flooding the surface with leach solution or lixiviant with little understanding to the parameters that support optimum recovery of the metal. Heap leaching has evolved into a controlled process whereby a complex low grade ore is stacked in shallow lifts (under 10 m in most cases). The ore is usually crushed and agglomerated, conveyor stacked on an engineered containment system (leach pad) and irrigated in a controlled manner. The lixiviant chemistry is designed to extract the optimum amount of metal from the ore. At first glance, heap leaching appears to be simple in nature. In fact, it is a very complex process. A plethora of technologies such as material handling, environmental control, analytical techniques, solution chemistry, hydrology and many others contribute to the design and operation of a heap leach. Heap leaching requires an inter-disciplinary approach between geologists, mining engineers and metallurgists. Many operational factors affect heap leaching. The process must address climatic factors, flexible operation, quality control before and after leaching, physical characteristics of the ore, geology, mineralogy, reagent consumption, solution application rate and methods (wobblers or emitters), particle size, and favorable conditions for bacterial growth and survival. Predicting, troubleshooting, and optimization of leach recovery is a significant challenge when considering the number of variables involved and their interactions The survey updates many of these key operating parameters to the current state of the art. It should provide the reader an excellent benchmarking summary of these factors on a site-by-site basis."

Jan 1, 2016

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By S. G. Britton

Microcomputer analysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran, or other language dominated such efforts. These programs have taken years to develop and prove out. This paper explores a new management tool used at TMC on a daily basis to track and improve continuous mining systems through the use of microcomputers and Lotus 1-2-3 software. By analyzing data provided by section foreman, shift foreman, and maintenance personnel against predetermined goals, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The results of this system on the productive output of TMC systems are on the order of ten percent improvement.

Jan 1, 1991

By G. L. Mowrey

One of the critical parameters of any automated coal mining system is the ability to only cut coal and not the rock / waste surrounding it. To do this the system must be able to detect where the coal-rock/ waste interface is. The U.S. Bureau of Mines is investigating a new approach to vibrational coal interface detection (CID) by utilizing an adaptive signal discrimination (ASD) system to perform feature extraction and classification of complex vibrational signals. Accelerometers, geophones, and piezoelectric films are mounted on mining machines and/or strata and are used to monitor vibrations produced during mining operations. Selected data are digitized and the ASD system is trained on known types of vibrations (e.g., "cutting coal" and "starting to cut roof"). A signal classifier is then generated which can be used to identify unknown waveforms. The ASD system can be retrained if mining conditions change significantly.

Jan 1, 1990