Search Documents

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Saturn light that significantly improves illumination for roof-bolting machine operators while reducing glare. The existing roof-bolter lighting was the baseline and was compared to the Saturn at 100, 75 and 50 percent intensities. Discomfort glare and disability glare were measured by the De Boer rating scale and the Mars Letter Contrast sensitivity test, respectively. Thirty study participants were tested. Discomfort glare was reduced at least three levels with the Saturn luminaire. Visibility levels were four to 6.5 times better with the Saturn than with the baseline. The Saturn design is freely available for commercialization.

Despite two large projects represented in the keynote docket, the mood of the 2011 SME Arizona Conference was summed up best by Ferol Baker, general manager of New Mexico Copper Corp. (a wholly owned subsidiary of Themac Resources Group), ?In the past, it seemed like you couldn?t go to a conference like this without hearing about one big new greenfield project after another. Now what you see is companies doing internal expansion or small-scale brownfield development.? Overall, the tone of this year?s meeting, held at the J.W. Marriott Resort at Starr Pass in Tucson, AZ, was upbeat, yet practical. From the keynote and luncheon addresses to the six panels of sessions, the projects described were positive about the future, yet focused on the details required to make those projects come to fruition.

Jan 1, 2012

By J. S. Jaspal

Mining of thin coal seams is both difficult and uneconomical. As a result, most of thin-seam coal reserves in the U. S. are not being mined. It is estimated that nearly 910 Gt (K. Unrug, 1985) of coal reserves exist in 355 to 710 mm thick seams. The Bureau is attempting to develop new techniques for mining 150 to 1065 mm thick coal seams. This paper summarizes the research work on existing thin-seam mining techniques, testing on small and full scale physical models of the Bureau slot mining concept, and computer modeling of the full-scale process.

Jan 1, 1992

By Richard M. Tinlin

The mining industry needs to assure compliance with the Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500). Congress has enacted this legislation with the intent of preventing, reducing, and eliminating pollution of the nation' s surface and groundwaters. Recognized sources of pollution such as seepage from tailings ponds, waste dumps, and contaminated effluent from mine dewatering operations pose a serious threat to adjacent groundwaters. In addition, technological innovations being implemented by the industry such as in situ leaching of low grade ore deposits may also lead to ground- water contamination. An adequate monitoring methodology designed to meet the needs of the mining industry is needed. Monitoring and control methodology devised for other man- caused sources of ground- water pollution - e. g., landfills - offer considerable promise for adaptation to the problem. The prediction of deleterious effects on groundwater quality usually requires extensive geohydrological data in addition to a thorough analysis of the mining activity that is underway or projected. If the avail- able data are adequate, mathematical models of surface and groundwater flow can be constructed that will help to predict effects on water quality. Data are inadequate to allow a realistic interpretation of pollution potentials. These data can be supplemented by computer simulation as a method to explore a number of possible environmental effects and also to develop a minimum-cost approach to identifying and gathering the additional necessary supporting data. Incorrect assessment of the important environmental considerations may, in many instances, prove to be the weakest link in analyzing the financial feasibility of a mining operation.

Jan 1, 1973

By Aurel Goodwin

Remarks of Aurel Goodwin, Chief, Division of Health, Metal and Nonmetal Mine Safety and Health, Mine Safety and fEealth Administration, U. S. Department of Labor, before the Society of Mining Engineers of the AIME, Littleton, Colorado, on October 18, 1979. I appreciate this opportunity to speak before the Society of Mining Engineers of the AIME. The topic of my presentation is the Mine Safety and Health Administrations's (MSHA) concern and obligations with regard to asbestiform minerals. Asbestiform minerals - the magical group of hydrated, silicate minerals which possess a fiber like structure capable of being woven, like and into cloth. Their unique combination of properties, such as resistance to heat and chemical attack, high tensile strength, and flexibility was recognized centuries before Christ. Pausanias, the early Greek geographer, speaks of golden lamps made about 430 B.C. with incombustible wicks of "Carpathian flax." The Romans used asbestos as cremation clothes to conserve the ashes of deceased persons of rank. Charlemagne had an asbestos table cloth that he used to pass through fire to clean (1). Early recognition of the health hazards associated with exposure to asbestos was documented in the first century by Pliny the Elder, a Roman naturalist, and Strabo, a Greek geographer. Bath wrote of slaves with sickness of the lungs, whose occupation was that of weaving asbestos into cloth. This concern for the health of asbestos workers disappeared over the ages.

Jan 1, 1979

By P. Mendoza, R. Siwale, H. Amini, R. Silva, M. Richards, V. Ngcoza, D. Rivera, C. Canaza, R. van Reenen

Development of a realistic flotation model to predict its performance is of paramount importance to the processing plant and operators, a model that accounts for predictive and no-predictive maintenance simulating individual equipment downtime and the effect of it in the metallurgical performance on the flotation bank with final recoveries and grades has a huge advantage on optimizing the flotation circuit/bank in terms of mechanical and metallurgical side. The Model was developed in a dynamic environment that allows for a better and more realistic simulation of the flotation bank. The maintenance model accounts for the Failure rate, Mean Time Between Failures (MTBF), Mean Time to Failure (MTTF) and Reliability (R(t)) those characteristics are combined to a multi-compartment process model that consists of a slurry recovery model, two options of froth recovery models, entrainment and carry capacity as a final check for the system. In addition to the maintenance and process model, a dynamic dart valve model was added to the simulation in order to have a realistic model to control the slurry level at the flotation cell. The paper goes over a study case for a current flotation operation trying to explore all the elements and the simulator to optimize the Rougher flotation bank.

Mar 2, 2022

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

The semiautogenous grinding (SAG) mill is one of the most important pieces of equipment in the comminution of materials. Its objective is to reduce the size of the ore until the ore can be released and continue on its transformation process. Although it is a simple process that involves impact, abrasion and attrition, its energy consumption is extremely high and inefficient, with no more of 17 percent of the energy supplied going toward size reduction. This gives rise to an important challenge because any improvement generates great economic benefits.

By Raymond F. Mikesell

This paper evaluates the contributions of "third parties" to surplus capacity in the world metals industries in the 1980s. Special attention is given to the role of international development agencies, such as the World Bank, that have made project loans to state mining enterprises. The paper also reviews the contributions to surplus capacity of the International Monetary Fund and evaluates the large volume of credits from commercial banks to developing countries. Although the credits to Third World countries during the 1970s facilitated the expansion of mining capacity in those countries, no one source of financing can be held responsible for a significant portion of the expansion.

Jan 1, 1989

By Isabel F. Barton, Christian A. Rathkopf, Mark D. Barton

Rhenium (Re) is one of the rarest elements on earth and is a designated critical element in the United States and European Union for its uses in superalloys. Unusually among critical elements, Re is produced entirely as a byproduct of molybdenite (MoS2) mining, as pure Re minerals are extremely rare. However, Re concentration in natural molybdenites varies from a few parts per trillion to tens of percent. There are few known consistent patterns and no firmly established reason for this variation, making it difficult to use molybdenite Re content as a proxy for metal grades, a vector to high grades, a clue to the geological and geochemical nature of the ore deposit, a guide to overall Re resources or for any other of the applications that have been suggested for it over time. 

By Malcolm T. Wane

The subject matter of this paper, "Applied Rock Mechanics?," has its genesis in a recent field trip taken by the author. A more or less standard question asked at the mines visited was "How are you using the principles of Rock Mechanics to assist you in maintaining an efficient, safe, and competitive mining operation?" The question was couched in a number of different forms, but the intent was to determine whether or not a general theory based on reason and the scientific method was applied or whether the alternatives of tradition, intuition, ?common sense', revelation, ?shotgun methods' or authoritarianism were invoked. Perhaps two responses to this query will be illustrative of the general nature of the replies. At operation XYZ an extension to the known ore body has been found. The extension is of large enough size and grade that a mining scheme using load-haul-damp techniques is envisaged. Since this represents a departure from the present mining scheme, questions have arisen regarding pillar sizes, room and entry sizes and possible support requirements. A task force has been set up to expeditiously plan for these things and write the necessary specifications and requirements. The fundamental question was posed to members of this group.

Jan 1, 1971

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the U.S. mining workforce who are potentially exposed to RCS [1,2] as various ore bodies are drilled, blasted, hauled by truck, crushed, screened/sized and transported to their destinations. To examine a method for assessing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on 80 miners across seven unique mining sites. The data were then collated and partitioned using a thresholding scheme to determine exposures that were in excess of 10 times the mean exposure for that worker. Focusing on these short-duration, high-magnitude exposures can provide insight into implementing controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20 percent or more by reducing exposures that occur during just 10 minutes of work per eight-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By John E. Husted

Universities have education as their primary purpose. This appears to be an innocuous statement with simple meaning. In an age of conflicting semantics, however, cords and meanings are often lost or changed. The term education is often broadly expanded to encompass any form of learning process, or the accumulation of knowledge, and even to the beneficial application of knowledge to man's problems, hence one find that education in universities is not solely the formal process of texts, lectures, recitations, and testing by a batch process known as class room teaching. Despite critics of education batch is spelled with an "a", instead of an "o" - at least we hope so If one defines teaching as causing to learn, then the learning objectives may necessitate a variety of approaches within the teaching concept and research is among those favored at the graduate and some undergraduate levels. Research has been among the glamour words and certain fields such as oceanography and space science have had more than their share of glamour. Unfortunately, industrial mineral research has not had the competitive drawing power of enamoring students of the "note" generation in terms of glamorous accomplishment. Research today usually requires sophisticated equipment and such equipment is expensive, both for initial purchase and operation. Again, administrations, be they industrial, government, or academic, usually require

Jan 1, 1970

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By William W. Shriver

When the Henderson Project is completed in 1975, it will become one of the Free World's largest primary molybdenum producers. The Henderson Mine will be located approximately 50 miles west of Denver, Colorado, on the eastern slope of the Continental Divide. Ore reserves are currently estimated to be 303,000,000 tons with a grade of 0.49% MoS2. The mill and tailing area will be located approximately 14.5 miles from the mine in the Williams Fork Valley, which is on the western slope of the Continental Divide. Ore haulage from the mine to the mill will be by ten miles of underground railroad and 4.5 miles of surface railroad. The concentrator has been designed to mill 30,000 tons per day and will yield approximately 50,000,000 pounds of contained molybdenum per year. This paper is concerned with the tailing and water supply system for the Henderson Project and in particular the environmental considerations affecting their design.

Jan 1, 1970

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860's by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

By C. Widham

Introduction It is generally accepted as dogma that sampling contributes most of the error in gold fire assays. Differences in assay results on pulps from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" of relatively coarse gold particles. It is true that coarse gold particles can contribute to substantial sampling fluctuations. But, while the process of sampling is probably the major source of error, the analytical process cannot be completely ignored as a possible contributor to erratic assay results. To maintain a stable assay process, the analytic part of the system must also be kept in control. One method of monitoring the performance of the analytic system is to systematically assay standard materials, whose sampling characteristics are carefully controlled. Gold assay standards are not prepared, nor can they be prepared, to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for both preparation (i.e., comminution and splitting) and fire assaying and then come to conclusions only about the fire-assay process. Because most gold ores are very heterogeneous, sampling errors would, in most cases, completely mask the contribution of the analytical errors. Assay-standard material is prepared only to assess the accuracy and variability in the fire assay process. Because the objective of the assay standard is to provide information about the fire assaying, it is necessary to control the sampling error of the standard material, so that it is only a minor constituent of the discrepancies observed in any assay results. To do this requires that the particle size of the standard material be reduced to a point where the relative standard deviation of the sampling error (i.e... the standard deviation of the errors divided by the average gold content of the material) is 2% or less. For all but very homogeneous mineralization, this means that the material must be reduced to 100% -150 mesh before the sampling errors are adequately controlled. However, even reducing the particle size can contribute to sampling problems. The liberation of gold may cause segregation that can cause large sampling fluctuations that are not easily controlled while maintaining the desired grade. Because, in most cases, the standard material would already be in the "pulp" state when it is submitted to a lab for assay, it is not possible to entirely conceal the nature of the sample from the lab. This is a problem inherent in using assay standard material. Because of the contribution of sampling to error generation in the assay process, the use of "coarse" material does not solve the problem of submitting a totally "blind" standard to the lab. In the sections that follow, the selection, preparation, testing and use of gold fire assay standard material is discussed. While some may dismiss the production of standard material as folly, it is possible to produce and utilize standard material to stabilize and improve the fire-assay process to produce more reliable assay results. Material selection It is desirable to use material that has as nearly the same metallurgical characteristics as the samples with which the standards will be included. However, this is usually difficult. For many reasons, including the particle size at which a significant amount of the gold mineral is liberated, the sampling characteristics of even -150-mesh material may preclude the use of geologically and metallurgically similar ore as a standard. It is usually easier to get material having desirable grade characteristics with the necessary sampling properties than it is to find geologically and metallurgically similar material with the required sampling characteristics. High-grade standards are especially difficult to find and prepare. This is because, as grade increases, the size of the gold particles usually increases. Larger gold particles are liberated and tend to segregate during comminution, and the homogeneity of the material cannot be maintained. For grades much above 3 g/t (0.088 oz/ton), it is very difficult to find material that has the proper sampling properties. Old mill tailings are likely candidates for assay standards. Some of these have sufficiently homogeneous mineral contents, so that the sampling errors can be effectively controlled. Where mill tailings are either not available or are not acceptable, mineralization that has exhibited homogeneous results in reassays of the pulp material is also a good candidate for the standard. Finally, the mineralized rock being sampled may (and should) be used if adequate homogeneity in the -150mesh material exists. "Adequate" ("acceptable") homogeneity is defined below.) It is important to use standards having a wide range of grades. This alone may preclude the material being

Jan 1, 1997

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

By Alva L. Kuestemeyer, Randall J. Scott

INTRODUCTION Pincock, Allen & Bolt, Inc. (PAH) has developed a series of cost models for Western U.S. Gold Mines. The models indicate the economic potential of developing gold properties at various production rates and ore grades. Various combinations of mining and processing methods are also analyzed. The conclusions shown in this paper are taken from PAH's 600 page study titled, "Capital and Operating Cost Models for Western U.S. Gold Mines." PAH decided to develop the cost manual as a result of our perception of the industry's need for such a document. It was our impression that exploration development decisions were being made on the basis of limited economic information. PAH has compiled a substantial database on unit cost information. That database and the engineering capabilities of the firm allowed us to develop a reasonably detailed analysis of capital and operating costs and overall development economics. The study has developed a series of algorithms for underground and open pit mining, processing, G&A, and infrastructure costs. The capital and operating cost data served as a basis for performing after tax discounted cash flow analysis for the various development alternatives. For the base case scenarios, a 15% DCFROR was assumed and the required ore grade was back calculated using the computer. The ore grade versus production rate graphs summarize the economics of developing gold projects in the Western U.S.

Jan 1, 1987