Search Documents

By Enrique Jelvez, Pierre Nancel-Penard

The traditional way of generating open-pit mine production schedules has several limitations. This work addresses the design and production-scheduling problem by considering minimum operational space requirements under a Direct Block Scheduling approach to generate extraction sequences that satisfy the operational space required. For this, traditional formulations were extended by including a new set of constraints that generate operating spaces for mining equipment to move and extract material. Then, a heuristic algorithm produces close to optimal practical pushbacks. This proposal was applied in a case study, and the results show its ability to generate practical production schedules without sacrificing expected return, obtaining differences in terms of Net Present Value (NPV) lower than 1% when compared to the traditional approach.

Jun 25, 2023

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

By J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit-optimization stages of a mining project. This paper presents an approach for optimizing final pit limits concurrently over all realizations in a stochastic model and using a risk-management framework to manage the geologic and economic uncertainty. A heuristic pit optimizer is used to find multiple uncertainty-rated pit shells. These uncertainty-rated pit shells follow the mean-variance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk-management framework to further eliminate suboptimal solutions along the efficient frontier. This results in a smaller set of final pit shells that can be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits, and two regions are targeted as potential regions for further exploration.

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)- based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jan 1, 2024

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By K. J. Sollman

As a class, silicate minerals have likely found the broadest, if not largest volume, use in combination with polymeric binders of all industrial minerals. Among the silicates, calcium metasilicate, wollastonite, enjoys a front runner position in a near universal sense. It is a viable and desirable part of composites ranging from thin films to large moldings; from a common filler/extender for paint for your garage to a reinforcement for the exterior surfaces of a luxury vehicle affordable to very few. This article is focused upon the variations in particle morphology and the surface characteristics which, by way of commercial examples and discussion of active research programs, make this environmentally benign mineral so unique.

Jan 1, 1993

By L. Boyd, T. Martin, V. Gall

Water infiltration into subgrade infrastructure can cause major impacts on their performance. In addition to damaging the structure, water intrusion leads to deterioration of installations including electrical and mechanical components and in patron discomfort. To remedy these impacts, leak remediation is often carried out to halt water infiltration. Remediation methods include coatings, drainage, injection/stitch grouting, curtain (backside) grouting, and/or internal umbrella systems. Selection of the rehabilitation method depends on the structure’s use, owners’ priorities, its installations, structural conditions, surrounding ground, and hydrogeologic conditions. Since many factors influence the rehabilitation method chosen, a novel holistic approach is undertaken to understand leakage causes and consequences to develop the most appropriate, efficient, and reliable solution to extend the structure’s life. A reconnaissance phase combines geologic, hydrogeologic, and as-built information with detailed digital scans and visual observations to develop a database of existing conditions. This database, called a tunnelband, is used to develop the rehabilitation solution and made part of the contract documents, allowing for an informed bid by specialty contractors. Tunnelband and the preferred rehabilitation system are portrayed in contract documents, which are procured in various contract types depending on the owner’s preference and project characteristics. The pool of contractors are required to submit their understanding of this holistic approach by developing and supplying the owner with a detailed workplan. The completed rehabilitation is portrayed in detailed as-built drawings which also provide the owner with an operation and maintenance manual outlining for periodic observation of the structure and checking of its performance. Ultimately, this information is implemented into a “BIM Digital Twin” that is used by the operations and maintenance staff for long-term observations. This proposed novel framework for leak rehabilitation is currently being used successfully in a number of projects throughout the United States.

Jun 13, 2023

By T. E. Wilson

In conjunction with experiments to improve the particle size preparation of coal bore cores prior to washability testing, discrete-event breakage of coal, shale and homogeneous low-strength concrete cores was studied. Breakage of individual size classes by drop-shatter and by incremental tumbling in an end-over-end hand-driven tumbling cylinder revealed systematic changes in the breakage function, namely, that breakage in any size class diminishes as the number of events increases. The effect of the fines removal enhances the breakage of harder material (having lower grindability indices), but appears to have less effect for softer material.

Jan 1, 1998

By C. A. Rowland

The rising costs for and the possibility for limited availability of electrical energy are emphasizing the continual conflict faced in the selection of comminution circuits used in preparing ores for concentration, namely; capital cost vs. operating cost. Frequently, the circuit with the lowest capital cost is not the most efficient in the use of electrical power and wear resistant materials. The simplest circuit in terms of flow, pieces of equipment and capital cost is the single stage autogenous or partial autogenous circuit used to grinding primary crusher discharge or run of mine ore to the desired product size. (Fig. 1) From this circuit, complexity increases to multi-stage crushing circuits preparing feed for multi-stage grinding circuits. Fig. 2 showing a three stage rod mill ball mill arrangement is an example of a complex grinding circuit. Stage concentration further complicates the flow. Multi-stage circuits being the most expensive to install, often give the greatest operating flexibility and offer the best possibilities for the most efficient use of available power and wear resistant materials. Within available grinding circuits, other comparisons such as high speed vs. low speed mills, grate discharge vs. overflow discharge, metal liners vs. rubber liners, high charge vs. low charge, etc. all add to the conflict

Jan 1, 1977

By J. P. Morgan

The Vesta Preparation Plant of the Jones & Laughlin Steel Corporation is located on the Monongahela River, eight miles south of Brownsville, Pennsylvania. This plant is capable of cleaning 2400 NT/hr of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables. handle the -1/4" fraction of the raw coal feed. Cleaned -coal goes to boot classifiers where the +48 mesh material settles and is removed by bucket elevators. This 1/4 x 48 mesh material is then sent to centrifugal driers for dewatering. As designed, the minus 48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and dewatered by filtration. The-products of the heavy media circuit, the launder-table-boot-drier circuit and the cyclone-thickener-filter circuit are combined to constitute the shipped metallurgical coal. This Vesta-Shannopin mix is combined at J&L's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke.

Jan 1, 1962

By Jaime Lomelin

The brines from the sub-surface of the Laguna del Rey dry lake are pumped to Química del Rey, S. A. plant, where they are cooled in adiabatic crystallizers precipitating sodium sulphate decahydrate. This salt is dehydrated in multiple effect evaporators and dried in rotary kilns producing high purity anhydrous sodium sulphate. The spent brines from the sodium sulphate operation are concentrated in solar ponds, precipitating astrakanite and leaving a brine with a higher concentration of magnesium ions. This brine is treated with calcium chloride solution to eliminate the remainder of sulphates, leaving a solution of magnesium chloride ready for the manufacture of refractory grade magnesium oxide or periclase. The magnesium chloride is reacted with dolime to produce magnesium hidroxide which is washed, filtered, and calcined to produce soft burned magnesium oxide, which is briquetted and dead burned to produce the periclase.

Jan 1, 1984

By E. Kaya

Investigations of fine grinding of bituminous coal in a laboratory-scale pulverizer are described. The results indicate essentially "normal" breakage behavior at relatively coarse sizes (greater than about 20 µm) but show clear evidence for re-agglomeration in the fine size range (less than about 10 µm). A simplified population balance model for simultaneous growth and breakage has been formulated. Breakage rates and breakage distributions are assumed to follow the patterns typically observed in simple grinding systems. It is recognized, however, that solid particles and agglomerates may exhibit different breakage behavior. Agglomeration rates are assumed to be determined by contact probability, i.e. by the relative numbers of interacting particles. Based on comparisons of model simulations and experimental data, it appears that agglomerate re-breakage rates and fragment size distributions are quite different from those for solid particles. The result is that product size passes through a minimum and then increases with time as agglomeration begins to dominate.

Jan 1, 1996

By Zohreh Kazemi Motlagh, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Five-element style deposits are unusual hydrothermal systems that are typically characterized by a nickel-cobalt-arsenic- silver-bismuth metal assemblage. This mineralization is often represented by abundant native silver, arsenic, or bismuth, and followed by nickel, cobalt, and iron arsenides (skutterudite, safflorite, nickeline, rammelsbergite, and lollingite). The Black Hawk district in Grant County, New Mexico is one of the few examples of this mineralization style in the United States. Despite the differences in formation temperature, depth of emplacement, and host rocks between five-element style deposits worldwide, there are commonalities in mineralogy, ore texture, and composition. A detailed exploration of the native metal and arsenide phases will be performed to compare ore forming fluids between systems and the effects on styles of mineralization and paragenesis, as well as to aid in broader classification of the deposit style. Mineralogy and mineral relationships of the Black Hawk District and other five-element deposits worldwide will be characterized by reflected light petrography, scanning electron microscopy, X-ray diffraction, and electron microprobe analysis. Mineralogical phase diagrams will be generated to better understand the driving processes and evolution of the systems through native metal and arsenide precipitation.

Feb 1, 2024

By Colin Connors

Cemented rockfill is a key component in the success of underground mining at the Jerritt Canyon Joint Venture. The Murray and SSX mines are characterized by relatively poor rock mass quality, and the goal of complete mining recovery makes maintaining a high quality backfill product vital to the safety and efficiency of the mining operations. A large portion of the ore production from the Murray mine originates from drifting under backfill. Modelling studies performed to investigate induced loading of the backfill were used to develop engineering specifications for the backfill material. Operations history has shown an almost 100 percent stability of the backfill when mining is carried out beneath it. The volume of backfill required each year (approximately 300,000 tons) and the required cement content have a significant impact on the total mining costs. The potential for cost savings associated with higher replacement of cement with Type "C" fly ash and the implementation of a backfill strength management strategy were therefore evaluated.

Jan 1, 2001

By M. R. Paterson

Operational and economic factors tend to favor the application of continuous processes in preference to batch processes in the majority of mineral processing applications. In this paper, the requirement for a Continuous Elution Process is established and the development of a large-scale pilot plant is described. It is based on a Continuous Elution apparatus which has a number of special features. These are the subject of various patent applications. The apparatus is suitable for adaptation to the AARL, Zadra and other methods of elution. The performance of the Atmospheric Continuous Elution System (ACE) is concluded to have significant advantages over the batch process.

Jan 1, 1986

By Stephen R. Holsinger

During the year of 1972 ASARCO's Silver Bell embarked upon a project that would test a modified grinding circuit using direct digital compute against the performance of its other five grinding lines, implementation and subsequent outcome of that project has been previously reported in a paper by Pitts, et al. The main purpose of the present paper will be to describe major problems incurred during the implementation of this control strategy on the remaining five primary grinding lines and their solutions. Also included will be a discussion of changes made in operating philosophy and methods used since that report was written. Description The Silver Bell concentrator is a 10,436 tonne/day copper sulfide plant supplied by ore from two separate open pits approximately 4 km. apart. As well as receiving ore from these two main pits, ore is received from several exten¬sions of both pits. The ore bodies are variable in rock type and the extensions have increased this variability. Grinding is carried out by six primary, single-stage, 3.20M x 3.66M Allis Chalmers grate discharge ball mills in closed circuit with four Krebs D20B cyclones (Fig. 1). Each of these grinding circuits is controlled by four independent but interactive control elements. These control elements are the fresh ore feed, the water added to the feed end of the mill, the water added to the ball mill discharge sump, and the cyclone feed pump speed. At the present time, instrumentation for measuring primary process variables consists of Merrick weightometers for fresh ore feed, orifice plates coupled with differential pressure transmitters (dp's) for incoming water measurements, back-pressure diaphragm coupled with a dp for estimating ball mill discharge sump level, a magnetic flowmeter for determining cyclone feed velocity and a nuclear density gauge for measuring cyclone feed density. All measuring instruments develop electrical signals that are measured as 2-10 V DC "inputs o the computer interface.

Jan 1, 1977

Caterpillar unveiled a new dozer, the new Cat D10T2 dozer, that builds on the success the company has had with its D10T model. The newest version of the dozer includes refinements to its power train, automated controls and structures. The result, the company said, is high productivity with superior fuel efficiency, reliable operation with long-lived structures, as well as enhanced access for service technicians and operators. The D10T2 uses the latest load-sensing hydraulics technology combined with Cat advanced engine controls to maximize the amount of material moved for every drop of fuel burned. Improved filtration protects the fuel system, hydraulic system and power train oil system to help ensure high reliability and minimal machine downtime. Refined large structures, such as redesigned track roller frames, deliver longer service before rebuilds. Improved access and egress features enhance safety and productivity of technicians and operators, and optional powered access systems and platforms enable configuring the D10T2 for the site. Caterpillar offers the D10T2 with two variations of the Cat C27 engine with ACERT Technology. One version is U.S. Environmental Protection Agency (EPA) Tier 4 Final certified, and the other is capable of achieving emission levels equivalent to EPA Tier 2 standards. Both engine configurations produce net power of 447 kW (600 hp) in forward gears and 538 kW (722 hp) in reverse gears. The engine controller automatically adjusts power output based on the direction of travel. With the new system, the D10T2 has about 20 percent more power in reverse compared to its predecessor model. The result is faster cycle times and greater productivity in certain applications. The D10T2 is suited for a variety of applications including mining, heavy construction and bulk materials handling.

Mar 1, 2014

By Alexander Pomerantsev

In recent years, bucketwheel excavators have found wide application in open pit surface mining not only because of their large production capacities, but also because they easily lend themselves to automation. Krupp, Orenstein & Koppel, Buckau-Wolf, Mechanical Excavator, Lauchhammer, Manufacturers in Eastern Europe designed and installed many models of bucketwheel excavators that can excavate any type of materials, could be used in any climate conditions and for any type of technological schemes in open pit surface mining, (Photo I, II and III)

Jan 1, 1979

By Pedone Ezio Michele, Mohamed Dahir Holad

"The 4c segment is a part of the ""Oman National Railway Project” linking the mining area in the surroundings of Thumrait and the port of Salalah. It is 90 km long and the last 40 km stretch crosses a mountainous area near the city of Salalah. The project includes the excavation of a 33 km double and single bore tunnel and 10 km of safety tunnels. This mountainous area is a holiday destination for Omanis, thanks to its beautiful landscapes, especially in summer time due to the monsoon rains. The tunnelling design had to take into account both these environmental constraints and the limestone rock formations crossed, which are affected by significant karst features. Given the context, the conventional tunnelling method has been preferred. INTRODUCTION The Oman Railway Project (Fig. 1) covers the construction of approximately 2,150 km of railway line for freight and passenger transport which will connect together Oman’s main towns and industrial sites and it will form part of the Arabian Peninsula railway system “GCC Project”. The non-electrified double-track railway line must guarantee a speed of 220 km/h for passenger trains and 120 km/h for freight trains and must guarantee the transit of AAR (Association of American Railroad) H and D plates using clearance envelope according to AREMA (American Railway Engineering and Maintenance-of-Way Association) requirements. The design alignment must have maximum radiuses of curvature of 3,250m and a maximum gradient of 1.0%. The project is divided into 9 constructional and functional segments. •,Segment 4c will be constructed in the southern region of Oman, close to the border with Yemen, to connect the town of Thumrait with the Port of Salalah. •,Segment 4c will run through the Dhofar region and will be mainly used by the freight traffic which currently travels by road."

Jan 1, 2016

By Gregory M. Rumbaugh, Todd R. Kostecki, Christopher Mark

The paper examines five massive pillar collapses in underground stone mines in the eastern United States from 2015 to 2021. These collapses caused significant airblasts, surface subsidence, and damage to mine infrastructure. The study identifies factors contributing to pillar collapses, such as slender pillars with width-to-height ratios of 0.8 or less, and proposes a framework for evaluating and mitigating collapse risks.

Nov 1, 2023