Search Documents

By E. G. dos Santos, M. M. Veras, C. H. Sampaio, A. S. Young, R. S. Paranhos, C. O. Petter, A. C. Bastos

"The major challenges of the current mining are the energetic optimization, the lowest water consumption and minimizing environmental impact. One technique that eliminates much of the waste avoiding milling sterile, operating without water and to decrease the generation of waste at the end of the process, must be considered a major innovation. One of the most important developments in these past 10 years in the mining industry was expanding the use of high-tech sensors aimed at pre-concentration of ore. Among the mining areas where this type of technology is booming is the industrial minerals. The most common sensors are color sensors with Charge – Coupled Devices (CCD cameras) allowing through the RGB colorimetric system, the separation of minerals with different hues, and in many cases, a difference in brightness. More recently, the development of the use of dual energy X-ray transmission (DE-XRT) Dual Zone allowed the separation by atomic density of the mineral constituents of the rock. This paper presents a review of these two techniques (CCD and DE – XRT) as well some results showing the use of these two techniques for Earth Rare and Limestone. INTRODUCTION The mining industry is going through one of its biggest technological changes since the industrial revolution by the implementation of new technologies, according to Australian Mining Magazine (2015), whose theme emphasized one of the 10 greatest challenges that mining will face in the coming years. Optimization of the energy matrix in mining is focused on reducing water consumption and minimizing environmental impacts. The implementation of sensor technologies (Sensor-Based Sorting - SBS) allows elimination of mill tailings and permits the mill to operate with reduced use of water or totally eliminate this consumption (Young et al, 2016). According to Jönsson (2014) mining has undergone striking changes with the expansion of sensors of high technologies applied in the pre-concentration of mining ores. These techniques have contributed over the past 10 years in the recapture of mining areas with emphasis on the environment and/or operational optimizations. In line with the requirements of technological innovation, the mining industry is forced to make improvements in gravimetric processes ensuring better levels of Run of Mine ore feed in beneficiation plants. The implementation of automatic sorting, assisted by dual energy x-ray transmission (DE-XRT) sensor technology, or charged coupled device (CCD) image capture camera technology in the feed plant, allows for the selective sorting of individual particles into pre-concentrations (Veras et al, 2016)."

Jan 1, 2017

By Samuel W. Woods

The Tacoma, Washington plant is one of six plants in the United States Gypsum Company's Acoustical and Mineral Fiber Division. The Tacoma facility was acquired in 1959 along with six other mineral wool plants from the American Rock Wool Company. Originally, the Tacoma plant was built as a carbide plant during the Second World War and after that was converted and operated as a mineral wool plant by several insulation companies. Through these early years, the use of raw materials at Tacoma consisted primarily of slags along with small percentages and various combinations of silica (in various forms such as gravel), limestone and basalt. These raw materials were melted in cupolas using coke as the heat source. Raw material usage and types as well as mineral wool production methods and equipment remained without major changes for many years.

Jan 1, 1983

By R. F. Harig

Designing an underground nuclear waste repository is a complex process. Although many decisions are involved before the design is complete, the first three--what the target horizon is, what the underground boundary is, and where the entry point will be located--are important because they establish the basis for the entire repository design. Even more important than these decisions, however, is the data on which the decisions are based. Because the current data are limited, an aggressive data gathering program is needed during the next design phase to augment information about the intricate interplay among all facets of the repository design and the geologic medium in which the proposed repository is to be developed. Although unique to modern engineering enterprises, the challenges involved in designing a repository in the unsaturated zone are within current technology and engineering practices.

Jan 1, 1991

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

The following errors were inadvertently included in "How millisecond delay periods may enhance or reduce blast vibration effects" by R.M. Wheeler in the September issue of Mining Engineering.

Jan 1, 1987

By David E. Lindorff

The impact of surface coal mining on the geologic materials and ground water in different geologic settings is being investigated by the Illinois State. Geological Survey at three abandoned surface mines in Illinois. At a site near Ottawa in La Salle County, the overburden prior to mining consisted largely of pyritic shale; sand was the major component of the overburden and spoil at a mine near Coal City, Grundy County. Clays, lacustrine silts, and some shale and limestone were the dominant premining overburden materials at a mine near Harrisburg, in Saline County. Ground-water elevations at Coal City and Harrisburg are approximately at premining levels, whereas at Ottawa they are near the base of the spoil. Ground-water quality has deteriorated at all three sites, especially at Ottawa and Harrisburg.

Jan 1, 1981

By D. Suarez

The work of engineers responsible for the design and performance of mine facilities is often challenged by economic and practical constraints in the field. Problems have developed in implementing design criteria dictated by persons or agencies not familiar with the dynamic nature of mine engineering. Regional and site-specific conditions frequently require changes to standard designs, or the use of a completely innovative approach, which is not provided for in the regulations. The implementation of engineering design, therefore, usually requires a hard-sell approach to management and regulatory agencies that allows for a happy-medium to all parties concerned. Flexibility on the part of the regulatory agencies is needed to solve operational and environmental problems with sound engineering. Typical hydrologic issues which will be discussed fall in the following general categories: ? Design criteria for sizing water control structures (i.e., culverts, diversion and sedimentation ponds, ditches, etc.) ? Implementation (construction and operation) difficulties ? Regulatory compliance ? Reclamation planning with hydrologic considerations ? Protection of groundwater resources

Jan 1, 1986

By D. L. Ealy

At the Beckley Mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by using a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1980

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By D. Ofiara, M. Lewis

Tunnel Boring Machines (TBMs) have been used in mining in decades past, but their use has been limited and sporadic. This has changed in recent years, with TBMs being used at Stillwater Mine, Grosvenor Coal Mine Slopes, Sirius Minerals potash mine, and more. These machines are all full face, circular TBMs—a design that has thus far have been unable to tackle a larger issue for mines: typically a flat floor is needed for mining vehicles to traverse. A novel type of non-circular boring machine is now answering the need to quickly reach underground ore bodies while cutting a rectangular profile in hard rock. This cross section allows for use of typical mine trucks and other rubber-tired mine vehicles. The machine uses disc cutters to cut the rock, and has a support structure similar to an open type TBM; however, the cutting geometry is entirely different. The machine is currently cutting an access tunnel at a silver mine. This paper reviews the design and operation of the novel noncircular tunnel boring machine, and describes possible future adaptations to provide safe, sustainable mine development.

Mar 2, 2022

By P. Saunier, S. Fourmont, R. Stafford, A. Jung, J. Mlynarek

The safe and economical storage of tailings generated by modern day mining operations is possibly the single largest challenge faced by miners today. By nature, tailings are a waste product that have little to no economic value. Yet, their physical and chemical contents can pose incredible environmental hazards if not stored correctly. The variety of factors that are met when designing Tailing Storage Facilities (TSFs), means that in most cases, a low-cost solution is sought to accomplish storage, meet environmental regulations, and adhere to industry best practices. TSFs can be large dam face structures or smaller structures like retention/evaporation lined ponds. Water management is potentially the single largest factor that miners and designers must contend with when constructing a TSF. Water is a necessary component in the process of extracting ore but can be difficult and expensive to remove once it is mixed with solid tailings particles. As a result, the most common disposal of these water containing tailings, called a slurry, is to simply discharge into an embanked TSF (Vick, 1990). These structures, just like any other water retaining dam, can breach releasing contents downstream. Despite modern advancements in TSF design, there have been numerous dam failures that have resulted in tragic loss of life and ecological devastation. Most notably in the last decade, the Brumadinho and Mariana Dam disasters in Brazil killed 278 people in downstream communities when TSF dams failed in 2019 and 2015, respectively (Rotta at el., 2020). Similarly, in 2014, the Mount Polley tailings spill in British Columbia was the second largest tailings spill on record and caused extensive damage to adjacent watershed ecosystems when the TSF embankment was breached (Byrne at el., 2018). While there were indeed numerous unique and underlying factors present in each of these structural failures, a shared element in the devastation was the large-scale release of unstable liquefied tailings

Mar 2, 2022

By E. J. Peuraniemi, J. T. Yli-Penttilä, A. Jokilaakso, K. M. Riihilahti

Dust formation and the reaction mechanisms of copper matte particles were investigated in simulated flash-oxidation conditions. The granulated and ground matte consisted of 72% Cu, 4% Fe and 21 % S (by weight). Experiments were conducted by using a laminar flow furnace with a reaction-gas composition ranging from 20% to 75% O2 (by volume) in nitrogen. The particle feeding was carried out by a single-particle method, and samples were quenched after a specified reaction time ([~] 0.05 to 0.4 s) in a cold water film. Experimental temperatures ranged from 800o to 1,300o C. Chemical analysis was used to determine the degree of oxidation, and optical and scanning electron microscopes, combined with energy dispersive analysis, were used for characterization of the reacted particles.

Jan 1, 1999

By C. L. Wilsey, K. M. Oakes, W. J. Reich, M. J. Protani

The time frame required to complete the National Environmental Policy Act (NEPA) process for a new mine or the expansion of an existing mine can range from nine to 24 months, or even longer. The time frame will vary depending on whether an environmental assessment (EA) or an environmental impact statement (EIS) will be completed Completing properly designed baseline studies to collect natural resource data to support the EA or EIS prior to the start of the NEPA process can shorten this time frame. In this paper, a two-year natural resource baseline study by Homestake Mining for the Ruby Hill Mine, Eureka County, NV, is used as a case study to describe how a properly designed and executed natural resource baseline study streamlined the NEPA process.

Jan 1, 2003

By Michael J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to in situ leach mine (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Cas a Grande mine, transmissivity fluctuations are spatially correlated suggesting that at the scale of ISLM, the hydraulic process is heterogeneous and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the simulated annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming, and uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be reevaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1993

By Erwin K. Roesner

The difficulties encountered while sinking deep shafts for Potash Mines in southern Saskatchewan have been the subject of several papers in the past. Geological and hydrological conditions of the strata overlying the potash deposits require special techniques for ground and water control during shaft sinking. The easily soluble potash ore requires the lining of these shafts to be virtually watertight to assure long term and safe operation. This paper describes the construction of the most recently completed potash shaft for the Potash Corporation of Saskatchewan. The shaft was designed and constructed by Thyssen Mining Construction of Canada Ltd. and it is located near Lanigan, approximately 110 km east of Saskatoon.

Jan 1, 1980

By Emily Wortman-Wunder

Attendees at December?s Arizona SME Section Conference at the Hilton El Conquistador Resort outside of Tucson, AZ were feeling optimistic and ready to get to work after a year of steady growth and recovery in the mining industry. During the two-day event (Dec. 5-6, 2010) and the preceding American Mining Hall of Fame banquet and awards ceremony, the focus was on copper, worldwide population growth and regulatory pressures, with several smart new projects featured alongside updates to traditional large-scale copper development projects. Keynote speaker Timothy Snider, chair of the University of Arizona?s Lowell Institute for Mineral Resources, hit the mood of cautious optimism when he analyzed the global demand for resources, using the case example of copper. Over the next 20 years, he said, the world?s population is expected to grow to 9.2 billion and the average annual per capita copper use is expected to rise from 2.2 to 4.5 kg (5 to 10 lb). The increase in demand will provide tremendous opportunity for mining companies, he said, but cautioned that the opportunities are balanced by negative influences on demand and pressures on supply. While demand for copper is currently growing, Snider noted that there were significant downward pressures on demand as well. These included a western world that is overbuilt, in-creasing use of substitute materials in new construction and the rise of wireless devices. He also noted new regulatory pressures, and pointed out that resource development now had to occur within a context of sustainability on several levels.

Jan 1, 2011

By Gary N. Greenfield

This morning, gentlemen, I should like to discuss resin anchors of a type introduced to North America approximately 2-1/2 years ago. We shall also briefly review the basics of mechanically anchored rockbolts so that a general comparison may be made. Previous efforts with synthetic resins were aimed at aiding a mechanical Or "point" anchor, obtain a better purchase in the rock mass. Resin cartridges of the type to be described in this paper are capable of achieving point anchorage or full encapsulation of mine roof or rockbolts. Of significance, therefore, is that unlike a mechanical bolt, placed and tensioned, celtite rockbolts may be fully grouted and tensioned or left untensioned in the installation sequence. Our principle effort has been to offer this system to mining and civil engineers who have encountered difficult rock conditions and wish to reinforce strata to achieve a greater degree of permanence and safety.

Jan 1, 1972

By CHENCHEN SUN, GUOPING LUO, GUOCHENG ZHANG

In this study, the conditions of raw materials and fuels were simulated for Bayan Obo iron ore concentrate by adding pure calcium fluoride (CaF2) in various concentrations to Australian iron ore. The mechanism by which the fluorine (F) content of the lattice influenced the reduction swelling properties of the iron ore briquettes during various stages of the reduction process was investigated. The results provide insight into the mechanism governing the reduction swelling process in Bayan Obo ore briquettes, which could be used to direct real?world production practices, particularly those related to the rational utilization of Bayan Obo ore resources.

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By A. S. Ibrado

Research investigations on the chemistry of the adsorption of gold cyanide on activated carbon have mostly reduced the role of activated carbon as the provider of the large surface area needed for adsorption. Most do not go beyond suggesting that oxygen functional groups on carbon play a key role in the adsorption process. Our research shows that the nature of the material, specifically its structure, is a crucial factor in the adsorption equation. To delineate the effect of adsorbent properties, gold cyanide was adsorbed on a series of carbonaceous adsorbents, including lignite, coals, anthracites, carbon blacks, graphite and activated carbon, which covers wide variations of composition, surface acid group content, and degree of graphitization. The results show that the adsorption of gold cyanide per unit area of adsorbent is not related to the amount of oxygen groups on the surface or even the total oxygen content of the material. However, they show very strong correlation with the degree of graphitization of the adsorbent, which indicates that the graphitic plates of activated carbon play the most important role. The findings suggest that majority of the adsorption occurs on the plate faces of the graphite crystallites of activated carbon.

Jan 1, 1992