Search Documents

By David A. Hedderly-Smith

Sealaska Corporation, the Alaska Native Regional Corporation of Southeastern Alaska, was organized under the laws of the state of Alaska pursuant to the federal Alaska Native Claims Settlement Act of 1971. Large areas of Sealaska's 630,000-acre (250,000 hectare [ha]) fee subsurface holdings are underlain by carbonate, and while much of this material is assumed to be common variety limestone and lesser dolomite, at least two areas in the Silurian Heceta Limestone contain high-quality limestone at tidewater. This limestone has many potential commercial uses. On northern Prince of Wales Island, about 90 miles (144 km) north-northwest of Ketchikan, resource development at Sealaska's Calder deposit has established a reserve of 13 mil- lion short tons (st) (12 million metric tonnes [mt]) of carbon- ate rock containing an average of greater than 98 percent CaC03, approximately 0.5 percent MgO, less than 0.5 per- cent Si02, and approximately 0.15 percent Fe203, with insolubles averaging less than 0.5 percent and an average Hunter Brightness of 92.07 for the -150 mesh grind (with a bright- ness cutoff of 90). The deposit is open at depth and to the south. Ultimate reserves will likely be several times those currently established. In 1998, Sealaska began mining the Calder deposit, with about 100,000 st (90,000 mt) produced, and also completed a marine terminal one half-mile (800 m) from the deposit. The terminal can load ships up to 680 feet (200 m) in length at a rate of 2,000 st (1,800 mt) per hour. 0 m) in length at a rate of 2,000 st (1,800 mt) per hour. On Dall Island at Breezy Bay, about 60 miles (100 km) southwest of Ketchikan, Sealaska has identified a limestone reserve in excess of 150 million st (135 million mt) that (based on 18 surface samples distributed evenly over about a section of land) contains about 98 percent CaC03, and less than 0.5 percent MgO, 0.5 percent Si02, and 0.15 percent Fe203. Brightness of the Breezy Bay carbonate is considerably less than at Calder. Five samples of brighter material from Breezy Bay returned brightness analyses in the high 80s and low 90s; average brightness is probably below the mid- 80s. Sealaska has also identified a deposit containing more than 19 million st (17 million mt) of similar rock near View Cove, a few miles south of Breezy Bay.

Jan 1, 2001

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By H. O. Harju

In July 1968, P.T. Inco Indonesia was granted a Contract of Work to explore and develop the nickel laterite resources on the southeastern peninsula of the island of Sulawesi. Since 1970, exploration has centred on the deposits at Soroako as the site for initial project development. This paper describes the exploration methods used to evaluate these rather unique laterite deposits, the geology of which is described in the first section of this volume.

Jan 1, 1979

By F. C. Townsend

Centrifugal modeling was used to evaluate reclamation schemes of; (a) flocculants, (b) sand/clay mixes, (c) flocculants/sand addition and (d) capping with sand or sand/clay mix. Results suggest the hierarchy of effectiveness is: (d) capping, (b) s/c mixes, (c) flocculants/sand addition and (a) flocculants. Comparisions between currently used large strain consolidation computer programs reveal no difference between piecewise linear or finite strain calculations. Correlations between numerical and centrifugal model predictions reveal excellent agreement on magnitudes; however, rate predictions require improvement in laboratory input data and centrifugal scaling relationships.

Jan 1, 1987

By Leslie Thompson, Randy Hiebert, Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology is capable of detoxifying cyanide and nitrate and immobilizing metals in wastewater from agitation cyanide leaching as well as heap leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to detoxify cyanide and immobilize several metals from a mine process wastestream at a mine in Nevada. The demonstration was performed jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy's (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-01-0. MSE Technology Applications, Inc. (MSE) located in Butte, Montana, was the contractor responsible for conducting the project, and Pintail Systems Inc. of Aurora, Colorado, was the technology provider. The pilot-scale unit was field tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was con­sidered to be very successful in detoxifying cyanide from the mine process water. The process was also determined to be very effective in removing metals. The pH was consistently neutral­ized and nitrates were successfully removed in the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to offer an innovative, cost­effective alternative for the treatment of mining wastewaters.

Jan 1, 1998

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Joy Global is helping to bring mining performance and analytics to the next level. By evaluating underground haulage, a significant component of the Room and Pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Joy Global is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way. These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer ‘nice to haves’, they are ‘must haves’. Starting with the best products and the right people is a first step, but then what? How do mines take their operations from just OK to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way. The fundamentals of operational excellence (OpEx) are based upon the DMAIC process, which stands for define, measure, analyze, improve and control. DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes; then improving the performance and controlling the operation. Joy Global uses Joy OpEx or ‘lean’ principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety. These same principles can be applied in most situations to streamline processes, improve operations and deliver value. As applied to mining, OpEx is seen as moving the needle on value creation by first identifying the value stream, then analyzing the areas that are not optimized. Once defined, these areas are ‘designed out’ of operational processes to create an automated operational flow. At a US coal mine, Joy Global was brought in to apply Joy OpEx principles to optimize mining and haulage to improve productivity and reduce costs. This multi-phase process started by defining the existing systems challenges to start finding areas for improvement."

Jan 1, 2017

"With a longstanding reputation for engineering expertise, Weir Minerals continually develops solutions and technology to better serve the mining industry. Recognizing that throatbush wear rate has a major impact on the overall efficiency of slurry pumps, Weir Minerals has developed superior rotating and axial adjustment technology.In many applications, the pump’s throatbush is the component that has the shortest life compared to the impeller and liners, with considerable variability.Adjusting the gap between the throatbush and the impeller front shroud reduces hydraulic recirculation in the pump. This prevents localized wear on the throatbush, improves hydraulic efficiency and lowers the total ownership cost for the operator. To avoid impacting the plant’s production, these adjustments are often performed while the pump is operating. However, this can have safety implications for individuals working at the front of the pump unit.“Manually adjusting an alloy throatbush on a large pump requires several people and is laborintensive. It requires mechanical tools to adjust the four pusher bolts, one at a time, in order to reduce the gap between the throatbush and impeller. We wanted to find a safer and quicker way to extend the wear life of the pump with regular adjustments, which led us to development of this technology,” said Marcus Lane, global product manager for centrifugal pumps for Weir Minerals.“Our automated throatbush adjustment solutions are available for pumps fitted with either rubber or alloy throatbushes on Warman slurry pumps used in the most arduous applications, and have been designed with our customers’ safety and pump operation in mind. By mechanizing the adjustment procedure, personnel are removed from the line of fire, and the accuracy of axial movement is increased,” said Ron Bourgeois, director of slurry pumping technology group for Weir Minerals."

Mar 1, 2019

By Mark Alan Marlkos

Blebs of solid bitumen from the Magmont West orebody of the Viburnum Trend were examined and analyzed in an attempt to relate hydrocarbon distribution and origin to ore genesis. The bitumen was calculated to be approximately 48 to 63 percent aliphatic and is considered to be a polymerized normal crude oil. Polymerization, which was probably caused by water-washing, hardened the bleb surfaces and appears to have "frozen" the blebs during primary migration from local source beds. Comparison of the bitumen to kerogen in local shaly partings strongly Indicates that the oil was derived locally. The polymerized oil blebs are considered to have been derived from a type II (marine) kerogen. Textural analyses indicate that oil migration occurred after lead-zinc mineralization and at temperatures that exceed normal ancient or present geothermal gradients. The following sequence of events is postulated for the Magmont West orebody: 1 Generation of hydrogen sulfide during diagenesis of a normal organic-rich carbonate sequence. 2 Introduction of pulses of hot, metal-rich fluids that resulted in: a Lead-zinc mineralization by the following reaction: Me++ + H2S ? MeS + 2H+ b Solution of carbonates by excess acid produced during the above reaction. c Brecciation of host rock in some cases. 3 Passages of the pulse resulted in: a Carbonate buffering of fluid system to more alkaline conditions. b Precipitation of dolomite c Slight temperature drop. 4 Eventually the high temperatures Introduced by heated brine caused oil generation and initiated primary migration. 5 Water-washing and mild biodegradation altered the hydrocarbon blebs to their present composition.

Jan 1, 2013

By John H. N. Yen, James M. Marquardt, Larry H. Heflin

INTRODUCTION On February 17, 1995, WMATA Contractor J.F. Shea holed through the last segment of rock tunnels of the planned 103-Mile Rapid Transit System for the Washington Metropolitan Area Transit Authority. Through the joined efforts and cooperation between the owner and the contractor, the project was completed on time and within budget. The Glenmont extension is on schedule to open in Mid-1998. The complete 103-mile system is scheduled to open in 2001. WMATA’s earlier 19 miles of rock tunnels had been done since 1976 ? By drill and blast with heavy horseshoe steel sets, sets with shotcreting over wire-fabric by TBM and NATM. All rock tunnels were primarily in metamorphic gneiss and schist, part of an east coast lithology that outcrops in a band running from below Richmond, Va. To above New York City. The 5,400 ft. long twin six meter tunnels of the Glenmont line had been earlier de-signed in 1979 by URS of NYC using Jenny Engineering of Pittsburgh, Pa., as a tunnel design specialist sub consultant. Jenny had provided two alternative designs, one conventional drill and blast horseshoe and one for Tunnel Boring Machine. Funding considerations had put the design on the shelf and it was clear that the state of the art had led to improved design methods in the intervening years. Before URS was tasked to update their design in1992, the Authority reviewed its earlier hard-rock experiences in light of the funding mandate to complete each segment on a limited budget and an expedited schedule. Many factors considered and many opinions were in leading to a final decision to drop the earlier designs and redesign for a single designated means of tunneling. That method was the New Austrian Tunneling Method. The NATM had been used earlier on WMATA for both soft-ground and rock tunnels. In the public’s eyes the NATM had become inextricably linked with the use of PVC’s and filter material enveloping or partially enveloping the underground structures to give the holy grail of tunnels, a water-tight structure. Although this link of waterproofing methods with excavation and support methods was essentially severed, a general feeling of their interdependence no doubt helped lead to acceptance of the NATM decision because of the waterproofing design that accompanied it. The Authority decided to drop the TBM and conventional options and provide bid documents for NATM only. URS asked LAW Engineering of Atlanta to provide the NATM design of the tunnels and associated shafts.

Jan 1, 1997

By Victor M. Mercado, Jay B. Shah

Spalding DeDecker Associates, Inc. (SDA) designed a tunnel project that fulfilled the Sustainability Objectives of Social Equity, Environment, and Economics. The project translated the principles of Sustainable Development into actions that lessened the impacts of construction on environment, lives of residents, businesses, traffic, and other social systems (i.e., shopping, recreational, and educational). The project involved the construction of a 16,108 feet of 84 inch diameter sanitary sewer interceptor by tunneling 40 feet beneath the ground surface through difficult geological and hydrogeological settings. An effective public information and stakeholders relationship program was developed to achieve the stated objectives of sustainability.

Jan 1, 2003

By R. Kramer, A. Habibi

A ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system includes three intake and six exhaust shafts, and three surface axial fans ventilate the mine in a blowing configuration. Airflow quantity, pressure losses and air psychrometric characteristics were quantified, and the influence of moving cages and skips in the shaft examined. The benefits of utilizing high-accuracy digital pressure transducers and advanced psychrometers were seen when undertaking a “leapfrogging” survey to gather data needed to build a computer ventilation model. Two underground booster fans with VFDs are idle but available at the mine. The ventilation model was used to determine the optimal booster fan locations to decrease operating cost by reducing the load carried by the main fans. A leakage study was conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next 15 years of mine operation and investigates the effect of proposed scenarios.

Jan 1, 2014

By H. T. Miller, L. M. Scott

Radiation exposures in Uranium operations may result from external beta-gamma radiation emitted by Uranium and its progeny, internal exposure to alpha and beta radiation due to the inhalation and ingestion of Uranium ores, Radon gas, and Radon progeny in mine, mill, and laboratory atmospheres and from the contamination of environmental working surfaces and clothing by Uranium-bearing compounds and ore. This paper summarizes occupational experience with reference to the exploration, surface mining, underground mining, milling and transport of Uranium by one company in the U.S. and Canada.

Jan 1, 1981

By Robert M. Rowe

Among the increasing operating costs affecting today' s processing facilities are those necessary in meeting the continually growing requirement for safe and environmentally sound materials- control and handling procedures. Of particular interest are materials listed as hazardous, the need to maintain accurate records of their acquisition, consumption and disposal, and the obligation to employees and the community to have information available regarding such materials. Some requirements affecting modern operating facilities are reviewed in this paper, and potential methods for dealing with complex handling and documentation requirements, including computer automation, are discussed.

Jan 1, 1991

By M. Soya, M. Imazu, Ö. Aydan

"SUMMARY Taru-Toge tunnel is being constructed using drilling-blasting technique as a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan. The maximum overburden is about 400 m. The authors have been carrying out a monitoring program to measure dynamic and multi-parameter responses of tunnel during and soon after the blasting operations using a multi-parameter monitoring system (Acoustic Emissions (AE), Electric Potential (EP), Temperature (T), Humidity (H) and Air Pressure (P)) and stand-alone type compact accelerometers developed by the first author. The measured response involves dynamic vibrations and other measurable parameters caused by blasting as well as by stress-redistribution around the tunnel face. This is one of the first attempts in the world to measure the response of rock mass caused by blasting at a very close vicinity of the tunnel face. In this paper, the authors present the outcomes of this unique monitoring study on the dynamic responses of the Taru-Toge tunnel during excavation and discuss their implications in actual applications. INTRODUCTION The real time monitoring of the stability of tunnels are of great importance when tunnels are prone to failure during excavation such as rockbursting or squeezing (i.e. Aydan et al. 1993, 2001). Experimental studies by the authors showed that rock indicates distinct variations of multi-parameters during deformation and fracturing processes (i.e. Mizutani et al. 1976; Aydan and Daido 2002; Aydan et al. 2003, 2011). These may be used for the real-time assessment of the stability of rock structures. An application of this approach was done to the Taru-toge tunnel a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan (Imazu et al. 2015). The parameters measured involve electric potential variations, acoustic emissions, rock temperature, temperature and humidity of the tunnel in addition to the measurements of convergence and loads on support members during the face advance."

Jan 1, 2016

By H. F. Ghezzi

The indirect method of drying coal fines is applied to filter cakes which ordinarily contain 22 to 30% moisture and are not readily transportable. The "Thermal Dryer", which operates on the mass transfer principle, has found wide use in coal preparation plants. The thermal dryer is penalized in operation by the necessity of adding coarse coal to the wet fines before entering the dryer body in order to produce a permeable bed, and thus enable hot gases to uniformly contact the wet mass. The ratio of coarse coal to fines varies from 2:1 to as much as 4:1, depending on the average particle size, moisture, and ash content of the fines.

Jan 1, 1985

By D. Malhotra, K. Purdy, G. Ramadorai

INTRODUCTION Today, flotation is clearly the dominant mineral concentration method. Since it is a relatively selective process, it is used for almost all sulfide minerals. A recent U. S. Bureau of Mines study indicated that approximately 225 million metric tons of sulfide ore was processed in 67 plants in the United States in 1980 (USBM Staff, 1981). There were over 100 plants processing copper ores in the world (Bassarear, 1985). Sulfide ores containing lead, zinc, copper, molybdenum, precious metals, cobalt, nickel, and iron are generally separated and concentrated by flotation. This chapter briefly reviews the plant practice related to the recovery of the above-mentioned sulfide minerals with emphasis on chemical reagents used for the production of marketable-grade products. PROCESSING OF SULFIDE ORES It is beyond the scope of this chapter to review the milling data for operating plants which have been extensively covered in literature (Tveter and McQuiston, 1962; Rausch and Mariacher, 1970; Weiss, 1985; Crozier, 1979). However, the following generalizations can be made regarding the processing of sulfide ores: 1. The primary grind is targeted to produce as coarse a product as necessary to provide an economic degree of liberation. 2. The concentration process, generally flotation, is designed to produce a concentrate consisting predominantly of valuable minerals and a middling fraction which may require further grinding to produce an optimum release of minerals. 3. The chemical reagent suite (collectors, frothers, etc.) for the separation of sulfide minerals from gangue minerals is generally complex. Total reagents used in the flotation process can be as high as six to eight, as is the case for lead and molybdenite separation from complex sulfide ores. 4. Chemical reagents are generally expensive because of the high selectivity for sulfide minerals. The process flowsheet is dependent on several factors, including ore grade and mineralogical composition. Generic process flowsheets for processing different sulfide ores have been developed for discussion in this chapter. However, there appears to be a consistent relationship between the reagent combination choice and the mineralogical composition of the ore (Tveter and McQuiston, 1962). These are covered in detail in the following sections. LEAD AND ZINC Galena (PbS) and sphalerite (ZnS), which commonly occur together, are the only minerals of lead and zinc, respectively, in most primary deposits. Feed ore grades are typically 1 to 5 percent Pb and 1 to 10 percent Zn. Very often economic quantities of copper and precious metals, silver and gold, also occur with these base metals.

Jan 1, 1986

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By Erich Sarapuu

Today's increasing needs for rapid excavation have stimulated efforts to break rocks without explosives. The application of electric energy for this purpose has been studied by a number of investigators. Following principles have been used in electrical rock breaking: 1. induction heating5 2. high frequency heating4, 14 3. microwave heating6 4. contact resistance heating9,12 5. resistance heating11,13 6. electron beam heating1, 3 7. plasma jet heating2, 8 8. arc heating7 9. condensor discharge energy14 In this paper the presentation of the principles of electrical fragmentation is limited to a process called "electrofracing". This technique uses electrical heating of rock by electrode contact resistance9 and resistance heating" phenomena. The electrically induced stresses inside of rock generate forces which break up the material. The fracturing of ore takes place by tensile stresses instead of compressive forces. The electric energy merely creates fractures in the rock and the separation of fractured material takes place by subsequent mechanical handling. Energy requirements in secondary breaking of iron ores have been about one to two kilowatt-hours per ton of ore. Power requirement is a function of the degree of fragmentation.

Jan 1, 1969

By W. C. Shanks

The Pioche District of Lincoln County in southeastern Nevada (Figures 1 and 2) has been an historically important producer of silver, zinc, and lead. Economic geology of districts in the Pioche area is summarized most adequately in recent reports by Tschanz and Pampeyan (1) and Gemmill (2) and only a few major aspects will be discussed here. Production in the Pioche District began in 1869 and early mining concentrated on silver-bearing fissures in lower Cambrian quartzites. In the early 1870's the Pioche District was second only to the Comstock Lode in world silver production (3). More recent mining activities have centered on the other major ore type in the area, bedded replacement of lower Cambrian carbonates by Ag-Zn-Pb sulfide ore. Production of replacement ore peaked around 1950. The present study is focused on the Pan American Mine because it is an excellent example of low grade carbonate replacement deposits, because there is little structural dismemberment, and because access was readily available. Most previous workers have suggested that both the fissure vein deposits and the bedded replacement deposits of the Pioche districts are a result of spatially related Laramide igneous activity. The purpose of this study is to determine whether ore genesis is a result of igneous activity or if mineralization might be related to late diagenetic processes such as formed Mississippi Valley "type" deposits. Stable isotopes of sulfur, carbon, and oxygen in ore and gangue minerals have been studied to determine the probable isotopic composition of the ore fluid and paleomagnetic studies of the carbonate rocks have been utilized to determine timing of mineralization. Additionally, petrographic and field studies of carbonate lithologies were undertaken in an attempt to delineate non-structural controls on ore localization. These studies are still proceeding and the results presented herein are, therefore, preliminary in nature.

Jan 1, 1979

By A. Noble

For the past 30 years, process flowsheet design has been accomplished largely through modeling and simulation. This approach provides circuit designers the freedom to test various separation approaches while minimizing physical and human resource requirements. The Limn® software provides a unique approach to process simulation, through a Microsoft Excel interface. While the software comes with standard process models for numerous unit operations, the Excel calculation environment and the accompanying VBA platform provide a convenient interface for custom model integration, even for non-experienced programmers. This feature is especially useful for university students in introductory process modeling and simulation-assisted flowsheet design courses as well as experienced practitioners with proprietary process models. This paper shows how the Limn® software may be used to solve basic process engineering problems as well as more comprehensive circuit design challenges. Industrial examples as well as opportunities for training and education are presented.

Feb 23, 2014