Search Documents

By A. Metzer

When paraffinic gases (ethane, propane, butane) are used as the gas phase in flotation systems, the initial rate of flotation and recovery are generally increased as compared with air. The mechanism of the effect of paraffinic gases in flotation was studied and it was shown that they co-adsorb with the collector ions on the mineral-aqueous solution interface. The effect of this co-adsorption was interpreted in terms of apparent increase of the effective chain length of the collector by the co-adsorbed gas. Adsorption densities, contact angles and flotation behaviour were studied on the following systems: a) Quartz - dodecyl ammonium chloride - ethane and propane b) Calcite - sodium oleate - propane and butane. The positive effect of the co-adsorbed gases is a maximum at low collector concentrations or where critical conditions for flotation with air prevail.

Jan 1, 1974

By K. O. Groves

Although chlorine oxidation has been found to be effective in destroying the CN ion, an excess of chlorine is needed to drive the reaction to completion. This often results in the formation of residual chloramines, which are toxic to aquatic life and often regulated by various states. The interhalogen, bromine chloride (BrCl), has been found to be just as effective but without the formation of persistent, residual chloramines. The hydrolysis and subsequent disproportionation of the highly-polar BrCl molecule essentially yields a solution of hypobromous acid (HOBr) and nonoxidizing hydrochloric acid (HC1). Studies have been carried out to directly compare the mechanism of CN destruction with chlorine and bromine chloride.

Jan 1, 1982

By Shosei Serata

Salt cavities have been proven to be a suitable structure for underground storage of various matters in gas, liquid or solid form. Since the technique of underground storage was developed mainly through field experiences in solution mining, a wider use of solution cavities for storage of gaseous and solid matters requires evaluation of three basic rock mechanics problems; cavity instability, boundary rock failure and surface subsidence. Cavity instability is due to the non-linear long-term creep properties of the surrounding ground media which are sensitive to cavity pressure changes associated with the storage. The cavity boundary rock failure is caused by the loss of effective confining pressure to the boundary rock media in the process of storage of gaseous and solid matters. Surface subsidence is the final outcome of the stress envelope originated around a cavity, eventually reaching the ground surface. The rock mechanics processes of instability, failure and surface subsidence are explained by using various field examples in salt domes and bedded formations. Methods of solving the problems are discussed including stress relief, stress control and computer optimization of design.

Jan 1, 1973

By Roy Moreby

Dartbrook Coal is currently developing a modern, high production (3.5 Mtpy) single longwall retreat coal mine in the Upper Hunter Valley of NSW, Australia. The location is a green field site, with no surface or underground mining operations ever having taken place in the initial target seams. The coal seams of the working section, floor and immediate roof average a total 20 m in thickness and contain a mixed carbon dioxide 1 methane seam gas ranging from 6.5 to 11.0 m3/t. The target seams have undergone detailed characterisation to assess hazards and quantify the controls required to minimise associated risks during mining. Risks identified during initial phases of exploration and 14 months of development include: • High gas emission during development. • Probable high longwall gas emission rate. • Medium to high propensity to spontaneous combustion • Possible carbon dioxide outbursts on geological structures • The main controls currently in place include, • Mine geometry and ventilation circuits • Exploratory drilling ahead of development • Intensive in seam pre drainage • Goaf drainage plants • Comprehensive monitoring systems • Underground environmental management plan. • Pre mining predictions of gas emission provided an indication of gas emission rates which have proven to be an under estimate. Current mine issues are; • Both surface fans are at full capacity (250 m3/s 1.4 kPa) • Both gas drainage pumps are at full capacity (2.3 m3/s) • Alternatives to extensive in seam pre drainage being investigated (surface to in seam hydro fracture) Review of mine design underway This paper describes the seam characterisation, assessment of mining hazards and summary of the management plan developed to address the risks identified. A review of current mine underground environmental performance is also provided

Jan 1, 1997

By George E. Summers

A salt dome appears to provide the basic medium requirements for the excavation of the 315 foot diameter, unsupported spherical cavity at a depth of 2700 feet required by the AEC in a proposed "decoupling" experiment. Tatum Salt Dome was a natural choice for a site because more geological and hydrological information has been accumulated on Tatum than any other salt dome on the Gulf Coast. The Tatum Dome is a mile in diameter, roughly flat topped, nearly cylindrical in shape and has some overhang at the top. The salt stock has nearly vertical layering of alternating bands of salt and anhydrite. In the vicinity of the dome, adequate fresh water for solution mining is available in surface streams and in subsurface aquifers. A saline aquifer is available for brine disposal. A tentative cavity location was selected near the center of the dome which meets the design criteria established by the AEC.

Jan 1, 1968

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By Aleksandar N. Nikoloski, Rorie Gilligan

Brannerite, UTi2O6, is the most common of the refractory uranium minerals and requires leaching under intense conditions to effectively extract the uranium contained within. Brannerite is often found together with apatite in metasomatic uranium deposits. Apatite and other phosphate gangue minerals can inhibit uranium leaching by generating phosphate ions which interfere with the reactions between acidic ferric sulphate and uranium minerals. As part of a detailed fundamental study on the leaching reaction mechanisms for brannerite, tests under a range of selected leach conditions were carried out with the addition of 10 g/L fluorapatite with the goal of identifying conditions where the negative effects of phosphate are reduced. Leaching was carried out for 5 hours with 0.05 mol/L Fe3+ as Fe2(SO4)3 with 0.25–1.00 mol/L H2SO4 and at temperatures between 25 and 96 °C. A single test was performed with 0.05 mol/L Fe3+ as FeCl3 and 1.00 mol/L HCl. In the sulphate system, the effect of phosphate was weakest at the highest acid concentration (1.00 mol/L H2SO4). In the chloride system, phosphate did not suppress uranium extraction, suggesting that HCl leaching could be a viable alternative for the leaching of high-phosphate refractory uranium ores.

Mar 17, 2021

By Felicia F. Peng

To minimize SO2 emission and the particulate problem during combustion of high sulfur coal fines is to agglomerate these fines in the presence of limestone. At subsequent combustion process, the sulfur in coal is oxidized and reacts with calcined limestone to form calcium sulfate in ash, while the base carbon is converted to clean energy. Seventy percent of sulfur retention can be achieved at Ca/S mole ratio of 3 at a temperature range of 500-400°C. The sulfur fixation in agglomerates involves the complex mass transfer and multiple successive reactions. The rate expressions have been developed to describe the progress of sulfur fixation in the agglomerates during combustion.

Jan 1, 1985

By Mark G. Aylmore, Eric J. Grimsey

Anenopyrite, both pure and in some cases associated with pyrite, was laboratory roasted either isothermally or at a constant heating rate, at temperatures mainly between 723 and 923 K and under environments of air, sulfur dioxide, oxygen and argon, as well as S02/02/H20/N2 mixtures. The mineralogy, arsenic contents and in some cases surface areas of the calcines were evaluated so as to provide an enhanced understanding particularly of the conditions under which the important transformations to pyrrhotite and magnetite occur. A thermodynamic analysis is also undertaken to rationalize the observations and provide some guidance for the operation of commercial roasters.

Jan 1, 1990

By Robert J. Guardia, James Rustvold, Robert A. Robinson, Christopher A. Robertson

In 1999, the Bonneville Power Administration (BPA) replaced approximately 730 m(2,400 ft) of damaged 42- and 36-inch concrete pipe by microtunneling Permalock pipe through sand and partly below groundwater. Microtunneling saved $3.5 to $5 million from the estimated cost of a shored excavation and avoided a railroad and contaminated valley fill. A slurry microtunnel boring machine (MTBM) was used for two segments where groundwater was present and a wheel excavator MTBM was used for one segment where groundwater was not present. This paper describes design and construction of this project that was completed within 2% of the bid and engineer’s estimate.

Jan 1, 2001

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By J. C. Willett, J. R. Sanfilipo, S. M. Podwysocki, P. D. Warwick

The U.S. Geological Survey is concluding an assessment of the major coal regions of the country. In this program, the quantity and quality of coals that are expected to be mined during the next 30 years are characterized. For the Gulf Coast region, the evaluation includes reviews of the stratigraphic setting, coal resources, and the quality of the Cretaceous to Eocene coals in four coal-producing areas. The coal-bed methane potential for these areas will also be evaluated. The results of these efforts will be a series of digital maps, text, and tables that will be published in a CD-ROM format.

Jan 1, 2000

By J. Brune

The need for reliable and adaptable underground mine communications has become a focal point for both the safety and logistics of a mining operation. New mine communication technology aims to connect personnel, equipment, and data together while setting up a network that can be utilized during normal operations and also in an emergency event. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) requires mine operators to establish post-accident, two-way communication between underground and surface personnel and electronic tracking for all mine personnel. Communications systems must be designed such that they can survive major mine accidents, including explosions, fires, inundations and ground falls. Typical, wire-bound communication technologies are vulnerable because wires are often destroyed in such accidents. Wireless technologies that work well on the surface, such as cellular telephone networks; have limited applicability underground because the wireless signals do not propagate through rock.

Feb 23, 2014

By Antonio Peralta, Guillermo Dante Ramírez-Rodríguez

Mining is generally considered a large-scale hightech industry. However, it has estimated that about 12 million people, about 30% of the world’s total mining workforce, relied on small-scale mining for their livelihoods. During the years, the large-scale mining industry has developed best practice environmental procedures, which have been applied in diverse settings through the world. In contrast, small-scale mining is better known for its high environmental impact and the lack of safe and healthy working conditions. This paper will discuss the environmental control strategies used by the large-scale mining industry, and its applicability to small-scale mining in developing countries.

Jan 1, 2005

By Michael G. Nelson, Sekhar Bhattacharyya

Between 1974 and 1977, a detailed study of coal pillar strength was conducted by the University of Utah at the Beehive mine in southeastern Utah. This study was funded by the U.S. Bureau of Mines, and included laboratory testing of coal samples, extensive field instrumentation and measurements, and finite element analyses based on the laboratory results. Recently, a similar analysis of the laboratory results and mine design geometry was completed using the LAMODEL program developed by NIOSH. The results of this analysis were close to the data collected in the field. This study allows comparison with the earlier finite-element analysis, and illustrates the utility of the LAMODEL software suite.

Jan 1, 2005

By Harold L. Lovell

The current interest in sulfur recovery from coal measures is indicated by a recent report prepared for the Public Health Service (1) It was noted that the concentration of pyrites to a product containing 42-48 percent sulfur should be relatively easy with present equipment. It was also pointed out that a utility potential exists for the high-grade iron concentrate which results as a by-product of the consumption of pyrites in the acid-making process. However, economics, marketing characteristics, location, transportation, pyrite levels and coal characteristics all strongly influence the feasibility of fostering industrial development of such processes. The extent of pyrite recovery and product quality is intimately related to pyrite particle size and its degree of liberation, a consideration usually given greater emphasis in metal ore preparation than in processing coals. Consequently, fine crushing to nearly 20 mesh probably will be essential for maximum practical processing. It appears that any process separating pyrites from a coal must involve a reprocessing of the normal preparation plant refuse, although some yields can be attained from certain existing operations as products from, a shaking table or a jig. Further, the existence of millions of tons of coal refuse cannot be ignored as a mined source of raw materials. The recovery of saleable products from such wastes, although untried on a large scale under current conditions, not only offers a realistic source of sulfur but also would achieve a secondary refuse with the minimal contents of substances which incite and propagate the burning of organic and inorganic combustibles. These silicate materials, thus beneficiated, also offer some potential for economic utilization. Some significant tonnages of pyrites have been produced from coal measures in the past, but the experience was, in general, not consistent with current coal preparation practice. The processes involved did not include cyclones and heavy media; nor were they carries out under the sociological environment concerned with pollution as exists today.

Jan 1, 1967

By Ronald S. Conti, Harry Dobroski

Re1iabl e monitoring a1ong an underground mine belt line is of great concern because of combustibles, electrical apparatus, and friction. Belt entries are strategically located where a fire can have rapid and disastrous consequences. This paper reviews conventional distributed temperature sensing systems based on resistive, thermistor, and thermocouple effects. These are shown to provide limited benefits. A new system tested by the U.S. Bureau of Mines based on fiber optics and time domain reflectrometry, promises much better temperature and spatial resolution, faster response, inexpensive cable, longer distance, and comprehensive data analysis. Test results in a small, controlled, in-mine fire are given.

Jan 1, 1992

By S. Michael Feroz, Paul Gribbon, Jan Rosholt

Approximately six billion gallons of combined sewage are discharged annually into Willamette River and Columbia Slough through Portland’s combined sewer system. The Columbia Slough Consolidation Conduit (CSCC) is an important element of mandated Combined Sewer Overflow (CSO) abatement. It includes2,548m (8,361 ft.) of 3.7 m. (12 ft.) internal diameter tunnel. The CSCC alignment traverses the UP railroad, Columbia Boulevard and parallels an old sewer. Geologic conditions include river alluvium and fine to coarse-grained flood deposits containing cobbles and boulders. This paper describes design and construction of a tunnel in soft-ground, with shallow cover and close to an old concrete sewer.

Jan 1, 1999

By Robert A. Jankowski, Charles Babbit, Natesa I. Jayaraman

The Bureau of Mines, together with Foster Miller Inc., has developed a compact, high pressure scrubber system for continuous miners. Powered by water energy alone, it can move up to 1.4 m3/s (3,000 cfm) of air and scrub a significant amount of the dust in the air. Full- scale model and underground trials showed excellent performance. Operated at 8.3 x 10[3] kPa (1,200 psi) and 38 L/m (10 gpm), the scrubber has reduced operator and return dust concentrations by more than 50 pct. This paper describes the full-scale model development, system fabrication and underground evaluations of this novel and inexpensive scrubber.

Jan 1, 1989

By A. Bruynesteyn

The results of leaching experiments in columns simulating 80 and 200 ft deep cores through a leach dump are discussed, By equipping the columns with can precipitation plants, actual plant conditions could be duplicated. The results produced a better understanding of the physical and chemical limitations of the leaching process.

Jan 1, 1975