Search Documents

By K. N. Han, M. C. Fuerstenau, T. B. Onlin

A mathematical model describing the concentration profile of fine particles in the axial direction in liquid fluidized beds has been developed for the removal of fine particles. A forward finite differentiation technique has been used to solve a continuity equation with a source term to predict the concentration profile and, hence the recovery as a function of time. With the aid of experimental results obtained using a fluidized bed of 3-cm diam, dimensionless parameters were identified. These parameters were used to predict the concentration profile of fine particles in fluidized beds of larger sizes. Four different sizes of fluidized beds, namely, 1.3, 3.0, 4.0, and 7.5 cm in diam, were used in this investigation. The amounts of bed particles used included 4, 8, 16, 24, 59, and 120 g, and the size of bed particles were 48x100, 100x150 and 150x200 mesh.

Jan 1, 1987

By J. M. Hans, M. F. O’Connell, G. E. Eadie

INTRODUCTION The U.S. Environmental Protection Agency (EPA) was required, under Section 114(c) of Public Law 95-604, to provide a report to Congress identifying the location, and potential health, safety and environmental hazards of uranium mine wastes together with recommendations, if any, for a program to eliminate the hazards. The approach taken to prepare the report was to develop model active and inactive mines and locate them in a typical mining area to estimate their environmental impact. A list of uranium mines was acquired from the U.S. Department of Energy (DOE). The inactive mines were separated from the list and sorted into surface and underground categories. A literature search was conducted to obtain and consolidate available information concerning the environmental aspects of uranium mining and shortterm field surveys and studies were conducted to augment this information base. Radioactivity emission rates were measured or estimated for each mining category and were entered into computor codes to assess population exposures and subsequent health risks. The general environmental condition of inactive uranium mines was determined by walk-through surveys in several mining areas. INACTIVE SURFACE MINES We assumed that a model inactive surface mine contains a single pit with the wastes (overburden and sub-ore) stacked into a pile adjacent to the pit area. No credit for reclamation is given to the model mine. In lieu of the availability of individual mine production statistics, the model surface mine size was established from the total ore and waste production statistics for all surface mines, divided by the number of inactive surface mines. The number of inactive mines, obtained from the DOE mine listing, are summarized by type and location (Table 1). For modeling, we assumed that there are 1,250 inactive surface mines. The total or cumulative waste and ore production for inactive surface mines from 1950 to 1978 is not fully documented. Uranium mine waste and ore production statistics, on an annual basis, were available for both surface and underground producers from 1959 to 1976 (D0159-76). Annual uranium ore production for each uranium mining type are available for 1948 to 1959 (DOE79) and for combined ore production TABLE 1. Consolidated list of inactive uranium producers by State and type of mining [State Surface Underground AL 0 9 AZ 135 189 CA 13 10 CO 263 902 ID 2 4 MT 9 9 NV 9 12 NJ 0 1 NM 34 142 ND 13 0 OK 3 0 OR 2 1 SD 111 30 TX 38 0 UT 378 698 WA 13 0 WY 223 32 Total 1246 201T] for underground and surface mining from 1932 to 1942 (DO132-42). In order to estimate waste accumulated prior to 1959, the waste-to-ore ratios from the 1959 to 1976 period were plotted vs. time and line-fitted by regression analysis (Figure 1). Unfortunately, the extrapolation of the line to years prior 1959 approached zero in 1954 although surface mining began in 1950. Therefore, a waste-to-ore ratio of 8:1 was used for the period of 1950 to 1959 based on ratios estimated by Clark (C174). The waste to-ore ratios for 1976 to 1978 were estimated using the line established in Figure 1. By using waste-to-ore ratios and ore production data, the cumulative waste and ore production for both surface and underground uranium mining is estimated to 1978 (Table 2). The estimated cumulative waste from uranium surface mining for 1950 to 1978 is 1.73 x 109 MT. A crude estimate of the waste accumulated at the model inactive surface mine can be made by dividing the total waste produced to 1978 by the number of inactive mines. This, however, overestimates the waste tonnage because some of the contemporary wastes are being produced by active mines, and the waste accumulated at newer mines has increased in recent years. To adjust for this overestimate, we assumed that all mines operating in 1970 will be inactive by 1978. This eight year period is approximately one-half the lifetime of a model

Jan 1, 1981

By Charles E. Melbye

INTRODUCTION In a discussion of South American exploration, it is difficult to know how much area to cover, as there has been such intense exploration for many years in all of the South American countries. Therefore, I have decided to discuss only Argentina, Bolivia and Peru in this paper, since I am most familiar with these three countries. This familiarity has been gained during my last 12 years of nearly continual exploration and mine development. Furthermore, these three countries form a contiguous block straddling the Andes Mountain chain for 2,200 miles in length N-S. Although Chile is part of this block, I excluded that country because it has had the longest recent history in South American exploration, and it is now in a mature stage where new important mines are being placed in production every year. Exploration must progress a lot for the other three countries to attain the stature of Chile. However, major exploration successes such as Yavacocha and Pieriva in Peru, Kori Khollu in Bolivia and Bajo Alumbrera, Agua Rica and Cerro Vanguardia in Argentina certainly indicates that these countries are rapidly accelerating in exploration successes and the resulting new mine developments. Also, by concentrating on three countries, I have avoided making this paper too lengthy. This paper will cover activities of both junior and senior mining companies, both of whom are making significant contributions to exploration. The junior companies often make the initial discovery, develop it further and then bring in a major company when large capital is required. Since most exploration is for gold and copper or combinations of these, most descriptions will cover these types. However, there are significant new exploration successes for zinc and for silver-lead-zinc, and they will be covered, as well. After descriptions of the various properties, there is included a discussion of the governmental policies of Argentina, Bolivia and Peru, as to how they are affecting exploration activities and budgets. Some of these problems could have a major negative affect on the future exploration plans of many companies. I have intended to cover what I think are significant exploration developments in each country, and if a company project is omitted, there was no intention to slight anyone. Since exploration results change monthly, there could be

Jan 1, 1998

By William H. Sutherland

INTRODUCTION Coal workers' pneumoconiosis and sili- cosis are only two of several diseases which are rlassed as pneumoconiosis. These are respiratory diseases caused by dusts which are inhaled and accumulated in the lungs. The individual particles of dust cannot be seen by the human eye. They are so small that they escape the natural cleansing mechanism of the nose and air passages and make their way down to the terminal air sacs of the lung where they injure the cells and cause the formation of scar tissue. Consequently, if there is exposure to high concentrations of dust over a period of time - usually, a number of years - the amount of scar tissue increases and begins to impair breathing. As a result, the miner develops shortness of breath, coughing and wheezing ad-if exposure continues - this progresses to permanent disability and frequently to death. Death is often due to pulmonary heart disease, the effect of stress on the heart 2s it tries to compensate for the weakened lungs. Specifically, silicosis is an occupational lung disease caused by the accumulation of free silica (quartz) in the lungs. Silicosis is considered the most important form of pneumoconiosis, not only because of its seriousness as a respiratory crippler, but also because of the large number of workers who risk contracting it in a variety of occupations. Quartz is one of the most common substances of the earth's crust, estimated at about 60 percent. Silicosis has been found in coal, metal and granite miners, as well as in other workers, such as sandblasters and pottery makers. Silicosis is also known to predispose the lung to tuberculosis and to increase the chances that a worker will contract chronic bronchitis and emphysema. The seriousness of silicosis was tragically brought to public attention about 50 years ago. During 1932-34, workers were involved in digging a tunnel through rock at Gauley Bridge, West Virginia. While their exposure time was relatively short, they developed silicosis because of the high concentrations of quartz. By 1936, 476 workers had died of silicosis and about 1500 were believed to have the disease (Washington Post, 1982). It is difficult to tell how many coal miners have silicosis. Because x-rays and breathing function tests do not show the difference the type of pneumoconiosis is generally diagnosed by the miner's work history. For example, if a worker

Jan 1, 1986

By C. Clark, J. Johnson, M. Stepan

"Shotcrete and mesh are often installed to control ground deformation, falls and ejection between bolts. The combination of mesh and shotcrete forms a panel or plate that is typically bent by ground extruding between restraining rockbolts. The ground pressure applied (that is, the resistance of these panels to bending) over large ground deformations is important for maintaining ground support safety. This paper describes a new test device that measures this resistance and its evolution over large deformations. Mixes of shotcrete, mesh and other components that can maintain significant support pressure are desired, a characteristic described as the “toughness” of support. Results show toughness depends largely on how shotcrete is integrated with other components. Shotcrete strength is less important. INTRODUCTION Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often called upon to do this (Figure 1). Applications are especially common in mines with squeezing ground or seismic loading. The support pressure maintained during ground deformation is key to the performance of these systems, and to protecting miner safety. However, the toughness of a design is difficult to estimate. Researchers at the Office of Mine Safety and Health Research (OMSHR) responded to this deficiency or “gap” by designing a full scale test device, described in this paper, and beginning a testing program. Some initial results from this program are reported to demonstrate test capabilities.BACKGROUND - TOUGHNESS Mining in ground that fails from the combination of in situ and mining induced stress is commonplace. Ground support elements are installed to reinforce such ground and preserve mine safety. Typically, the strength of support is considered key, and is used to prevent or halt yielding. However, ground movements driven by creep of weak ground or seismic loading may be impossible to halt altogether. In these cases, it is essential that support is able to yield with the ground in a safe manner while maintaining confining pressure that mobilizes the strength of rock in the immediate perimeter of the opening. In addition, it’s usually desirable to contain ground between rockbolts to protect miners from loose rock that might fall or be ejected. Shotcrete and screen are often employed, sometimes together and in combination with other support elements, to accomplish this function. A key characteristic of such a system is its ability to maintain support pressure through large ground deformations, a characteristic often called “toughness” – especially in support systems incorporating shotcrete. Toughness can be quantified as the work done during deformation (e.g. force x displacement)."

Jan 1, 2015

By Alper Kirmaci, Taghi Sherizadeh, Gunnar Wurst, Paul Brooks, Dogukan Guner, Samuel Nowak, Mina Esmaeelpour, Kutay Karadeniz

As mines continue to deepen and become more expansive, active monitoring of larger volumes of rock mass will become more critical to calibrate numerical simulations and to ensure the safety of underground workers. Monitoring larger volumes of rock mass requires low-cost sensors that are simple in construction and installation. In this study, a novel hybrid optical fiber cable (HOFC) designed for use in distributed optical fiber sensing (DOFS) via grouted boreholes was deployed to monitor a bulk mining operation in an underground metal mine. The HOFC was successfully used to monitor approximately 2.7 × 10 m3 of rock mass above excavations surrounding a pillar removal area in which six large pillars were removed simultaneously. A total of six measurement boreholes (maximum depth of 22 m) were used to measure strain along the optical fiber during the pillar removal operation using the HOFC, allowing for 70 individual strain measurement points, which were constructed for under one U.S. dollar each. Monitoring of the excavation area took place over a 44-day period after pillar removal. Extensional strains were noted in the areas closest to the removed pillars, while areas of compression were noted directly above the remaining pillar in the area. The results of the case study demonstrate that a low-cost optical fiber strain sensing network can be rapidly installed in a large excavation area and can provide highly sensitive strain measurements in a manner that would be cost prohibitive using other methods.

Oct 1, 2024

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By M. L. Klohn

The Felder ore deposit is a 5,000,000-pound uranium deposit in the South Texas Coastal Plain. It occurs in the basal sand of an Oakville Formation (Miocene) alluvial system. The host sand is a carbonate-rich arkose which contains virtually no carbonaceous debris and has been reduced by the local introduction of hydrogen sulfide. The ore lies well within the reduced zone and occurs as coffinite and uraninite that fill interstices and coat and replace grains. The overall geometric configuration of the ore is that of a winged, crescentic ore roll. Weak mineralization extends the wings of the ore roll and gives greater expression to the roll character. Departures from the shape are controlled by discontinuities in bed- ding and by proximity of the ore to the surface. Associated with the uranium is a broad halo of anomalous molybdenum. Subsidiary mineralized trends suggest a pre-existing up-dip position for the main roll. Oxidation from the surface largely destroyed this previous roll by solubilization of uranium. Uranium subsequently migrated into favorably reduced sand and reprecipitated at the present roll position.

Jan 1, 1970

By H. E. Epstein, B. K. Parekh, W. M. Goldberger

Comminution is the single most expensive operation in mineral processing. It consumes about 50% of the energy required for mineral extraction (Agar, 1976). Current comminution technology is both energy-intensive and inefficient. A novel noncontact comminution process concept was developed in this study, whereby selective lib¬eration of minerals from an ore could be potentially achieved. The process involves application of electric and ultrasonic energy to liberate minerals from gangue particles. Introduction The mineral industry is a large user of energy in the US. Energy usage is increasing as the grade of ores processed decreases. It is es¬timated that comminution of ores uses about 32 000 kWh (115 trillion kJ), or 2% of the electric power produced in the US (NMAB-365, 1981). Among other minerals, ce¬ment, iron, and copper processing plants are the largest users of en¬ergy in comminution. Very little of this energy used in conventional grinding (about 1%) is used to gen¬erate new surface. The remainder is wasted (Table 1). Thus, there are substantial energy-saving and economic incentives to improve the efficiency of crushing and grinding techniques for mineral recovery. With an energy efficiency of only 1%, it would seem possible to devise methods to significantly improve comminution technology. This requires that breakage force be applied only where needed, not indiscriminately as in a conven¬tional ball mill (NMAB-365, 1981). Can apparatus and methods be de¬ veloped for large-scale commer¬cial use that allow energy to be fo¬cused at intergranular bounda¬ries? If this can be done, mono¬mineral grains would remain in¬tact and the grinding action would be selective and substantially more efficient. The novel comminution process concept described in this paper uses a combination of electric and ultrasonic energy. This energy breaks the ore and selectively lib¬erates minerals. The process has also been termed a two-stage or electroacoustical comminution process (Goldberger, Epstein, and Parekh, 1982). The mineral grain boundary is usually the weakest area in an ore. By applying electri¬cal energy to the ore, the rock frac¬tures mostly at grain boundaries. At the same time, the electric shock creates secondary hairline fractures in the ore. Additional application of ultrasonic energy to this ore provides further break¬age. The concept was proven on a molybdenum porphyry ore but needs additional study. Technical Background There have been substantial im¬provements in milling machinery and grinding operations, but rela¬tively few attempts have been made to develop alternatives to conventional impact milling. Sev¬eral methods, however, have been investigated that relate to this study. In the early 1970s there was considerable interest in a size re¬duction method known as the Snyder Process (Cavanaugh, 1972). It involved charging coarse ore into a pressure chamber, pressur¬izing with a gas, and activating a quick-opening (15 msec ) dis¬charge valve that connected the chamber to a discharge duct. This allowed solids to fluidize and ac¬celerate, subjecting the material to a variety of impulse phenomena that caused the desired size reduction. Other nonimpact means of achieving breakage and selective size reduction have been de¬scribed in technical and patent literature. Kanellopoulos and Ball (1975) considered using heat to induce thermal stress in quartz¬ite. This would cause cracking and, thus, increase grinding efficiency. The use of electrical energy to induce thermal stress was studied by the General Elec¬tric Co., in cooperation with the Montana School of Mines, under a research grant from the Anaconda

Jan 9, 1984

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article concludes a two-part series on the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. Discussed are the consequences of fuse abolishment, the technical feasibility of changing to an alternative system, and an economic analysis of initiation systems. Last month, part one (ME, pages 31-35) described current use of initiation systems, incidence of accidents, and consumption values for safety fuse and other initiation systems. Consequences of Fuse Abolishment Cap and Fuse Manufacturers Two major safety fuse manufacturers, Ensign Bickford and Apache Powder Co., share the US fuse market. Marketing of Ensign Bickford safety fuse is done by Dupont. Dupont manufactures electric caps as a main product and recently introduced a new nonelectric initiation system (Detaline). Therefore, Dupont would be only slightly affected by the elimination of safety fuse from metal and nonmetal mining. Ensign Bickford, though a larger manufacturer of fuse, does not appear to emphasize the safety fuse market. In fact, safety fuse sales represent only about 10% of Ensign Bickford's total sales volume. Ensign Bickford is strongly pushing its Nonel product. It appears, therefore, that the elimination of safety fuse would have a limited effect on Ensign Bickford, and could ultimately be to the company's advantage. Apache Powder Co., however, would be seriously affected if safety fuse was eliminated. Safety fuse, although not its only product, constitutes a major source of revenue for the company. It currently does not manufacture a substitute product. Apache Powder Co.'s manager agrees that prohibiting the use of safety fuse would result in a greater market share of initiators for Ensign Bickford. Hercules could also benefit from the prohibition of safety fuse. Metal and Nonmetal Mining Industry According to an explosive company contact, elimination of safety fuse by a mandatory regulation would force some of the small, marginal mines out of business. Another powder company representative believes that eliminating safety fuse will result in uneasy situations for small operators not familiar with other techniques. These operators try to minimize the costs and traditionally like safety fuse. He believes that insufficient proof exists to substantiate the overall safety increase if the fuse is eliminated. Fuse manufacturers and distributors disagree, then, about the impact of safety fuse elimination. However, they tend to agree on some important points: • Safety fuse can be a safe method if applied properly. • Electric blasting can be dangerous due to stray currents, and may have higher misfire rates than safety fuse. • It is very difficult to compare the rate of misfires and partial round failures for different systems. This is due simply to the nonavailability of such data. In many cases, the misfires are not even reported to the shift boss, as required by regulations. • Safety fuse has high acceptance in certain applications, such as a face where Nonel or detonating cord are used, or in open-pit blasting. • The safety fuse industry appears to be phasing out on its own. It is expected that the fate of the safety fuse market will be similar to that of black powder. An investigation by Nitro Noble of Sweden "clearly states that the diminishing use of safety fuse has considerably reduced the accidents in Swedish mines." Mine Data Acquisition and Analysis As a part of the study effort, visits were arranged to 24 metal and nonmetal mines. In most cases, underground visits were accomplished. At least one drilling and loading operation was witnessed. The mines were grouped into four mining areas: Wyoming, Montana, Idaho; western Colorado and eastern Utah; Missouri; and southern Arizona. Of all mines visted, the safety fuse system was used in 11 mines, electrical system in seven, Nonel in five, and the Hercudet system in one surface mine. At each mine, the manager, foreman, and blasting crew were interviewed for information and opinions. Besides informal discussions with mine officials, a questionnaire was also filled out for each mine. Due to the extensive length of the information gathered, these data are not presented here.

Jan 2, 1984

By John Armstrong, Michael Savill, David Powell

Hong Kong is an intensively developed region and has the highest vehicle densities in the world. In 2000 there were 6.6 million people and 580,000 vehicles using 1,890 km of road covering the 1084 km 2 territory. The high vehicle and population densities together with the difficult terrain have seen road tunnels emerge as key components both in the current and future road transportation network. Currently there are eleven operating highway tunnels in Hong Kong, seven government owned and the remaining four “build, operate and transfer” franchises, see Figure 1. The very first tunnel was the dual two Lions Rock Tunnel completed in 1967and the latest the dual 3 lane Tai Lam Tunnel opened in mid 1998. Figure 2 shows the alignment and statistics for all 11 Hong Kong tunnels. Looking ahead, Hong Kong has embarked on the study and design of the next generation of major highways and as many as a further seven tunnels are currently under feasibility study or detailed design. This seems an opportune year to produce a broad appreciation of the fire strategy, life safety and ventilation practices in Hong Kong not only for the existing tunnels but the new standards and requirements for the next generation of Hong Kong tunnels. This paper provides an overview of the fire strategy, life safety and ventilation of Hong Kong’s existing and planned tunnels. The paper pays particular attention to the areas where the unique conditions and requirements in Hong Kong impacts on tunnel and systems design and the solutions adopted to overcome these challenges.

Jan 1, 2001

By William H. Langer

U.S. Geological Survey (USGS) recently initiated the Front Range Infrastructure Resources Project. This is a multidisciplinary study along the Rocky Mountain Front Range from Pueblo, Colorado, to Cheyenne, Wyoming, and is designed to collect, compile, and analyze new and existing data on natural aggregate (stone, sand, and gravel), as well as water, and energy resources. To identify aggregate resources in the Front Range, a 1:500,000-scale reconnaissance map showing locations and quality of both bedrock and surficial sources of natural aggregate in the Front Range urban corridor was prepared by processing the digital geologic maps of Colorado and Wyoming. The first step of the process was to identify map units as either bedrock or unconsolidated material. Bedrock was classified according to type (i.e., limestone, granite, gneiss, etc.), which in turn was classified based on the suitability of the bedrock for use as crushed stone. Unconsolidated materials were classified according to relative age, with the older, more weathered materials being defined as less suitable for use as aggregate than younger materials. As a spin-off from the Front Range Project, the techniques developed for analyzing the Front Range geology have been modified and expanded to include all of Colorado and New Mexico. More detailed digital aggregate maps (1:24,000 scale) are being prepared in collaboration with the Colorado Geological Survey (CGS). Maps from the CGS "Atlas of Sand, Gravel and Quarry Aggregate Resources, Colorado Front Range Counties" show the distribution of potential resources of sand and gravel and provide general information about the physical properties of the resources. These maps are being digitized and merged into a single Geographic Information System (GIS) data base. In addition, the project is adding more specific information to the maps about deposit thickness, volume, and quality. This additional information is being obtained through field-characterization studies and modeling activities. The GIs data base can be displayed and queried using off-the-shelf software such as ArcInfo?, ArcView?, and Map Professional?. In addition, the USGS is developing a decision-support system to assist users in analyzing various land-use options on resource availability.

Jan 1, 1999

By Sam H. Patterson

This paper is concerned primarily with the kaolin deposits extending northwestward from Macon, Ga., which is in the western part of the Irwinton district (fig. 1). These deposits are in a belt of kaolin districts extending along the inner edge of the Coastal Plain from the Aiken district, S. C., southwestward to the vicinity of Macon, a distance of 150 miles (250 km). Large kaolin deposits associated with bauxite also occur in an extension of this belt southwestward from Macon as far as the Eufaula district, Ala., a distance of about 130 miles (208 km). The belt splits away from the inner edge of the Coastal Plain in a southwesterly direction from Macon; the Eufaula district is approximately 50 miles (80 km) south of the contact of Coastal Plain sedimentary rocks with much older crystalline rocks. Structure The strata of Cretaceous and Tertiary age containing the kaolin deposits all dip gently seaward irom the landward edge of the sedimentary rocks. The dip of the Cretaceous strata is about 25 feet per mile (4.9 m per km). The dip of Tertiary strata is about 15 feet per mile (2.1 m per km). In places, the Tertiary strata overlap the older sedimentary beds and rest directly on the crystalline rocks. Faults having a few feet of displacement have been observed in several mines, but no major faulting is known in the area.

Jan 1, 1977

By Howard L. Hartman

In 1969, the OECD conducted a survey internationally to determine the status and needs for research and development in the field of tunneling. The findings also have some validity for underground excavation in general and for underground mining per se. Of the 17 countries responding to the survey, the U.S. leads in the level of support: $21.8 million and 720 man-years of effort over the last ten-year period. The total volume of R/D for the 17 countries was estimated to be $86 million and 5800 man-years. Performance of research was primarily by government agencies and public utilities (70%); the balance was conducted by private organizations and universities (15% each). In the categories of R/D subjects surveyed, three--Wk mechanics, soil mechanics, and geological exploration--outstripped all the rest in priority of effort to date. Ground support, equipment development, excavation, and environmental control received intermediate attention. The subject areas in which the least R/D effort has been expended are materials handling and systems evaluation. For the future, those R/D areas rated the most crucial to achieve technological progress in tunneling were excavation, ground support, and materials handling. The survey findings of tunneling activity indicated (1) a disturbingly low level of R/D activity in the private sector, (2) the necessity for a reordering of priorities in directing research efforts in the future, and (3) a lack of recognition to date of the importance of systems evaluation in R/D activities.

Jan 1, 1970

By Alan G. Mayton, Jon C. Volkwein

The U.S. Department of the Interior, Bureau of Mines, in cooperation with an American firm, has been contributing toward the creation of a new highwall mining system for extracting coal in active, unreclaimed contour strip mines in the United States. The prototype system features the computer-based, remote control, video operation of a thin-seam continuous miner. Haulage is accomplished remotely also with a 76-m (250-ft) long multiple-unit continuous haulage (MUCH) conveyor system on rubber-tire vehicles. One aspect of this multi-faceted effort has been to design a ventilation system for removing dust generated at the face during the extraction process. The remote mining system eliminates the need for personnel in the mined workings. Ventilation is required to remove visible dust from the area inby two video cameras. These cameras are located approximately 6 m (20 ft) from the face, one on either side of a modified Jeffrey 102HP continuous miner. Removing the dust from this area provides the remote operator with constant visual monitoring of coal extraction at the face and thus, insures the effective operation of the mining system. A ventilation system was designed for use in a mine opening with a maximum cross-sectional area of roughly 4 sq m (44 sq ft) excluding the mining machinery. This paper describes the ventilation system and discusses how it was developed in view of the constraints imposed by the mining equipment, mining conditions, and the extraction process.

Jan 1, 1989

The Chinese city of Shanghai is one of the fastest growing in the world. To keep up with the growth, two tunnels, three-lanes each, are being built beneath the Yangtze River to connect Shanghai with the Changxing River Island. To complete such a large project, Herrenknecht Tunneling Systems was brought in to construct the largest tunnel boring machine (TBM) in the world. The first Herrenknecht S-317 Mixshield has a diameter of 15.43 m (50.62 ft). It was built to construct one of the two 7.2-km (4.5-mile) tunnels. The tunnels are part of the Changjiang Under River Tunnel Project and will be at depths of up to 65 m (213 ft) beneath the Yangtze River in Shanghai-Pudong. These two tunnels are to be opened to traffic in April 2010, in time for Shanghai to host the World Expo. More than 20 million people live in the Shanghai area. The area itself has been growing at an extremely rapid pace for more than a decade and is in need of more space. The search extended beyond the natural limits of the Yangtze River Delta. As part of its incredible growth, 500 new vehicles are registered every day. The new tunnels will connect the Changxing River Island, with a population of approximately 600,000 people to the road traffic network. A bridge construction will also provide a traffic link between Changxing Island and the large island of Chongming.

Jan 1, 2007

By J. J. Kellar, W. M. Cross, J. D. Miller

Infrared spectroscopy has been one of the most useful experimental techniques for the analysis of surface reactions in flotation systems, including surface alteration and surfactant adsorption reactions. With the advent of Fourier transform infrared (FTIR) spectrometers, many low-energy throughput IR experimental techniques previously unused by flotation researchers have come into greater use. In particular, internal reflection spectroscopy (IRS) is the most often used technique for in-situ studies. To date, three IRS methods have been used for in-situ measurements. These techniques are evaluated for use in characterization of surface reactions in flotation systems. The method using mineral crystals as reactive internal reflection elements (IRE) is of particular interest because it allows surfactant adsorption densities to be calculated directly from in-situ spectral data in real time. Application of in-situ FTIR/IRS with reactive internal reflection elements will be demonstrated for collector adsorption reactions in each of the major flotation systems. The alumina (A1203)/sodium dodecylsulfate system is used as an example for insoluble oxide/silicate flotation, while the fluorite (CaF2)/oleate system serves as a paradigm for semisoluble salt flotation. For sulfide flotation, sphalerite (ZnS) is used as the reactive IRE with potassium amylxanthate and potassium ethylxanthate as collectors. In the case of soluble salt flotation, sylvite (KC1) is used as the IRE with n-octylamine as collector. Finally, the use of reactive IREs in the near-IR spectral region and in spectroelectrochemical research is discussed.

Jan 1, 1989

By Joseph R. Hatch

Previous studies of the Thompson and Temperly ore bodies show alteration aureoles in the Middle Ordovician host-rock limestones, dolomites and shales extending laterally as much as 60m from the ore. Thickness, texture, carbonate and clay mineralogy, major-, minor-, and trace-element contents; and carbonate carbon and carbonate oxygen Isotope compositions of the host rocks all have been significantly altered by hydrothermal processes. Organic geochemical analyses of samples from the basal 8-cm-thick carbonaceous shale bed and immediately overlying limestone bed of the Quimbys Mill Member of the Platteville Formation, collected from within the ore, the alteration aureole, and the unaltered country rock show: 1) solution of carbonates and residual concentration of organic matter, 2) decreases in the volatile (Si) and pyrolytic (S2) hydrocarbon yields In samples of the basal shale from within the ore, 3) decreases in the relative amounts of the lower molecular weight (<nC25) saturated hydrocarbons in samples from the ore, and 4) no changes in either the organic carbon isotope composition or the Rock-Eval or biomarker thermal maturation Indicators. In light of the 125-170°C depositional temperatures documented for the early marmatitic sphalerltes in these deposits by fluid Inclusion studies, the lack of thermal alteration of the organic matter suggests a relatively short mineralization episode, a conclusion supported by the relatively simple sphalerite band stratigraphy. The decreases in the volatile and pyrolytic hydrocarbon yields for shale samples from the ore supports a model for mineral deposition which obtains sulfide through reaction of brine sulfate and indigenous organic matter.

Jan 1, 2013

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By T. A. Griffin

Gentlemen: The subject of this paper is: ADVANCED APPLICATIONS OF BUCKET WHEEL EXCAVATORS AND RECLAIMERS. Against an urgent world wide energy crisis, the role of bucket wheel excavators and reclaimers in the surface mining of fossil fuels and other ores has been raised to new prominence. This paper will review the reasons for the expanded application of bucket wheel technology, its unique contributions, and other factors relative to volume, cost, versatility, and efficiency. Today, surface mining is faced with the twin challenge of (1), accelerating the rate of removal of massive quantities of overburden and ore, and (2), replacing comparable high volumes of overburden back into the mined-out portion of the pit. Optimum quantitites for - a single electrical power plant now range from 5 to 15 million tons of coal per year. The use of bucket wheels offers the best method for meeting this challenge at lowest possible cost. For example, an advanced application that also satisfies environmental concerns involves the simultaneous functioning of two bucket wheel excavators during surface mining operations. Working at spaced intervals and different levels in conjunction with a transfer conveyor and stacker, one excavator removes the ore while the other one transfers overburden to a stacker that replaces it back into the open pit. The result of this continuously operating cycle is: (1) removal of ore and replacement of overburden back into the pit in massive quantities, (2) at accelerated volume and extreme low cost that cannot be matched by conventional loading machines of any size, and (3) fulfills a basic environmental requirement which is to

Jan 1, 1974