Search Documents

By T. D. Oulton

The only known attapulgite clay deposits of any considerable extent and purity in the United States are roughly bisected by the Georgia. Florida state line between Decatur County, southwest Georgia, and Gadsden County, northwest Florida. Although attapulgite clay occurrences both farther East and South are known and have been mined to some extent in the past, at the present time it can be said that substantially: all of the commercial attapulgite clay mining and pro¬cessing is concentrated in a roughly rectangular area some 25 miles long by 15 miles wide,, in the general region of Attapulgus, Georgia, and of Quincy and Havana, Florida. Within this area are located the clay processing plants of the four major producers as well as most, if not all, of the currently active mining operations. The approximate location of the plants and of some of the open mines are shown in the local area map, Figure No. 1, for the purpose of orientation only.

Jan 1, 1965

By John W. Welty

Volcanic activity occurred during six periods of Arizona's geologic history. Precambrian volcanism occurred in two pulses at 1.8-1.6 billion years (b.y.) ago and at 1.2-1.1 b.y. ago. Volcanism occurred again in mid-Jurassic and Laramide (Late Cretaceousearly Tertiary) time. Volcanic rocks from these times are not used commercially in any significant quantity. Middle and late Cenozoic magmatic activity covered large areas of Arizona with voluminous volcanic rocks. During the mid-Tertiary magmatic pulse, explosive silicic magmatism, with eruption of areally extensive ash-flow tufts, covered large areas in the Basin and Range Province, while the Colorado Plateau remained largely unaffected. Basalt eruption also occurred during and immediately after silicic volcanism, leading to compositionally diverse suites of volcanic rocks. Late Cenozoic volcanism occurred throughout Arizona and was dominated by wide-spread eruption of basalt flows with local cinder-cone clusters and siliceous volcanic deposits. Perlite deposits near Picketpost Mountain in northeastern Pinal County account for the bulk of the industrial uses of mid-Cenozoic volcanic rocks. Other perlites of presumed middle Tertiary age are present in central, southeastern, and western Arizona, but to date remain unexploited. Arizona Fire Agate is a valuable gem material and is associated with volcanic rocks of middle Tertiary age. Basaltic rock of this age also is utilized in the manufacture of rock wool for insulation. Late Cenozoic volcanism produced most of the industrial-quality volcanic rocks. Basalt, cinder cones, and materials of rhyolitic composition are commercially exploited by municipal and Federal agencies and private industry for aggregates, road conditioners and maintenance materials, asphaltic concretes, cinder block construction, pozzolans, and landscaping. These deposits are generally confined to the Flagstaff and Springerville areas. A famous peridot gem locality is associated with late Tertiary basalts at Peridot Mesa on the San Carlos Indian Reservation. Important products derived from altered volcanic materials of late Cenozoic age include clay and zeolite. Arizona's volcanic-rock sequences are still incompletely known, particularly in central and western Arizona. The potential for recognition and exploitation of important new deposits of useful volcanic materials is high.

Jan 1, 1987

By Robert C. Sutter

In 1958, it became obvious to some of us in the solution mining business that there were certain problems in connection with our sodium chloride brining operations which were industry- wide. These were the types of problems which, while they were important to the safe and economical operation of our salt brining operations, were not such that their solutions would give an individual company a great competitive advantage over his competitor; and since they involve the safe and efficient mining of a natural resource, it was obvious that the answers would, in any event, be shared industry-wide. Since we were dealing with underground solution mining and, consequently, unseen and remotely controlled operations, the problems are formidable and the solutions difficult. While all of us were doing work to improve our operations, none of us could justify the expenditures necessary for basic research in these areas. Consequently, the idea was conceived of research sponsored by many companies with the same problems. In 1960, 11 companies entered into a' formal agreement to jointly support research on a specific problem of sodium chloride solution mining. The project to be undertaken was the development of a method for measuring the size and extent of underground solution cavities in sedimentary salt beds. It was agreed that all research was to be performed by independent research organizations. A part-time consultant or administrator was retained to administer the research contracts and to provide technical advice.

Jan 1, 1966

By Clayton J. Parr

Introduction This chapter contains brief discussions of various environmental protection requirements that relate to underground mining operations. Environmental disturbances at an underground mining operation can result from subsidence; water discharges; waste dumps; construction and operation of access roads and utility lines; construction and operation of surface facilities such as maintenance shops, bathhouses, and storage yards; and emanation of dust and noise from surface crushers. Construction and operation of a concentrator or washing plant may result in the emission of air pollutants, the discharge of water pollutants, the creation of noise, and disturbance of the surface. Tailings ponds can be the source of fugitive dust.1 This chapter is not intended to provide a detailed discussion and analysis of laws and regulations dealing with environmental protection. Rather, its purpose is to provide the engineer with a basic awareness of the existence and nature of such laws and regulations, as well as the procedural requirements that must be followed in complying with them. The body of law relating to environmental protection has grow" very rapidly and should continue to do to for some time. Because many of the laws have been enacted recently, numerous court decisions are being rendered to resolve disputes over their interpretation. Hence, the reader is cautioned to be alert for subsequent modifications of statutes and regulations, and new case law. Rules and regulations pertaining to environmental protection are implemented at all governmental levels. The most widely known laws are those enacted by the federal government that have nationwide applicability. However, separate requirements exist in each state, county, and municipality. Because of their general applicability, federal laws are discussed most extensively in this chapter. Ownership of the property is the most significant factor considered in ascertaining what rules govern the conduct of an operation thereon. If the land is held under lease, reference to the lease terms must be made in the first instance to determine what obligations must be met in order to prevent default and possible loss of the property. If the land is held under a lease from the federal government, the operator is subject not only to compliance with the lease terms, but also to a large body of laws and administrative regulations that pertain generally to the conduct of mining operations on land held under federal leases. Although operations on unpatented mining claims, the legal title to which remains in the federal government, are not subject to the same rules and regulations that are applicable to operations conducted pursuant to federal leases or permits, they soon will be governed by a special set of regulations that provide for protection of surface resource.2 Operations conducted on lands leased from a state usually are subject to numerous environmental protection requirements specified in the lease terms, in addition to rules and regulations promulgated by the state agency having jurisdiction over mining on state lands. Operations conducted on privately held lands are subject to fewer such requirements. Leases from private parties sometimes have environmental protection and reclamation requirements written into them, but generally to a far lesser extent than governmental leases. Operations conducted on properties owned by the operator are subject only to those laws and regulations that have general applicability without regard to land ownership. COAL SURFACE MINING CONTROL AND RECLAMATION ACT OF 1977 Introduction On Aug. 3, 1977, the Federal Surface Mining Control and Reclamation Act of 1977 was signed into law.3 It governs coal-mine operations on private lands, as well as on public lands. The Act is pervasive in its scope and is extremely long and complex. The basic purpose of the Act is to control and minimize the environmental effects of surface coal mining. Surface coal-mining operations are defined as activities conducted on the surface of lands in connection with a surface coal mine and surface impacts incident to an underground coal mine.4 The Act is administered by the Secretary of the Interior through a new agency named the Office of Surface Mining Reclamation and Enforcement.5 The Act contains detailed environmental protection standards and reclamation requirements, and it establishes a permit system for all surface coal-mining operations. Mining in certain areas and under ceri-in conditions is restricted or prohibited, and a mechanism for enforcement by the states is provided. Stiff penalties are provided in the event of noncompliance. Implementation Schedule Nonfederal Lands: As required by Section 501 of the Act, interim regulations setting mining and reclamation performance standards based on and incorporating standards set out in Section 502(c) were adopted effective Dec. 13, 1977.6 They will. be incorporated as amendments to Chapter VII of Title 30, Code of Federal Regulations. Permanent regulatory procedures for surface coal-mining and reclamation operations performance standards, which were directed to be promulgated by Aug. 3, 1978, were published in proposed form on Sept. 10, 1978. 7 They govern surface coal-mining operations in any state until a permanent state or federal program is adopted. As of Feb. 3, 1978, all new operations, and as of May 3, 1978, all existing surface coal-mining operations, on lands on which such operations are regulated by a

Jan 1, 1982

By Robert C. Freas, Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodities in this volume have as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as aggregates, fluxes, glass raw material, refractories, fillers, reactive agents in sulfur-oxide removal, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Holocene. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1989 about 798 Mt were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses. The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1994

By Harold B. Goldman

On the basis of tonnage, the sand and gravel industry is the second largest nonfuel mineral industry in the United States. In 1990, the production of sand and gravel was 927 Mt valued at $3.4 billion. California, which leads the nation with more than 126 Mt, together with Texas, Washington, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 Sieve (0.074 mm openings) to those passing a No. 4 Sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see chapter on Industrial Sand and Sandstone and Glass Raw Materials). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material that is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Sand and gravel is also used as construction fill, road base and subbase, and decorative material. Portland Cement Concrete Aggregates: Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15 to 20% water, 7 to 14% cement, and66 to 78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman and Reining, 1983). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate: Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.076 mm), uniformly coated and mixed with asphalt produced in the refining of petroleum. Sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement aggregate. GEOLOGY General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles that are sound and durable. Soundness and durability are terms used to denote the ability of aggregates to retain a uniform physical and chemical state over a long period of time so as not to disintegrate when exposed to weathering and other destructive processes. Individual particles must be tough and firm, possessing the strength to resist physical stresses and chemical and physical changes, that may cause swelling, cracking, softening, and leaching. The aggregate should not be contaminated by excessive clayey material, silt, mica, organic matter, chemical salts, and surface coatings. Physical Properties: The quality of aggregate depends upon its physical and chemical properties. These, in turn, may be inherent mineralogical and textural features of the rock or may be the effects of later changes such as tectonics, mechanical or chemical weathering, or incrustations. The physical properties most significant for concrete use are: 1) abundance and nature of fractures and pores, 2) particle shape and surface texture, and 3) volume changes which may occur because of freezing and thawing or wetting and drying. An aggregate is considered to be physically sound if it is adequately strong and capable of resisting the agencies of weathering without disruption or decomposition. Minerals or rock particles that are physically weak, extremely water absorptive, and easily cleavable are susceptible to breakdown. The use of such materials in concrete reduces strength or leads to early deterioration by promoting weak bond between cement and aggregate, or by inducing cracking, spalling, or popouts. Severely weathered, soft, micaceous, or porous materials may cause localized stresses to develop in concrete by swelling and shrinking during wetting and drying or freezing and thawing cycles. Physical Suitability of the Various Rock Types. Sedimentary rocks have a wide range in physical and chemical qualities. Sand- stones and limestones, if hard and dense, are ordinarily satisfactory, but many sandstones are friable and excessively porous and commonly are clay-bearing. Shales generally make poor aggregate material, being soft, weak, and absorptive. Most igneous rocks are satisfactory, being normally hard, tough, and dense. Tuffs and certain flow rocks may be extremely porous and have high water absorption and low strength. Metamorphic rocks differ in character. Most quartzites are massive, tough, and dense. Fine-grained marbles are usually durable, but coarse-grained marbles have low abrasion resistance. Gneisses are ordinarily very tough and durable. Some schists contain micaceous minerals that are undesirable because they are soft, laminated, and absorptive. Micaceous minerals are susceptible to splitting along cleavage planes and thereby impair particle strength and durability. Some schists and slates in particular are thinly laminated and tend to assume flat slabby shapes that lack strength-and do not pack well. Any or all of these rock types may be rendered undesirable because of harmful exterior coatings. Weathering processes, particularly the action of ground waters, deposit these coatings. The most common coatings are calcium carbonate, clay, silt, opal, chalcedony, iron oxide, manganese oxide, and gypsum. Particles with these coatings are undesirable as aggregates because the bond between particle and coating may be weak, and decreasing the strength of the aggregate-cement bond.

Jan 1, 1994

By J. N. Albright

Both microgravimetry and crosshole seismic tomography are means by which subsurface collapse and rock failure may be observed. We show results of calculations that predict changes in gravity and gravity gradient that result from void migration, bulking, and hydrology disruption due to room and pillar mining. Crosshole seismic tomography also holds promise for detecting and mapping changes in structure during subsidence. Commercially avail- able logging tools, advances in theory, and recent field results strongly suggest tomographic surveys are now possible. Subsidence phenomena which may be located are faulting, joint separation, bed parting, water table changes, and formation outgassing.

Jan 1, 1982

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

4.1 INTRODUCTION There have been numerous methods developed for predicting the final subsidence and final displacement profiles (Voight and Pariseau, 1970; Brauner, 1973a; Kratzsch, 1983). But for discus- sion purposes, they can be classified into six categories: theoretical, profile function, influence function, graphical, physical, and numerical modeling. The theoretical method employs mainly continuum mechanics theories and attempts to explain the mechanisms that lead to sur- face subsidence. Many models using nearly all kinds of material behavior have been developed. These include elastic (Salmon, 1963; Berry, 1964), plastic (Pariseau, 1968), viscoelastic (Iman, 1965), and elastoplastic (Dahl, 1969). The Profile Function Method is essentially a method of curve-fitting against the measured subsidence profiles in a particular mine or region. There are more than 20 profile functions developed empirically for nearly all major coalfields in the world. These include, to name just a few representative ones: Hungary (Martos, 1958), Japan (Hiramatsu and Oka, 1968), Russia (Avershin, 1947), United Kingdom (Wardell, 1965), and USA (Peng and Chen, 1981; Karmis et al., 1984). The NCB's graphical method in the subsidence Engineers' Handbook (1975) also belongs to the profile function method. The influence function method was first proposed by Bals (1931/1932). It was further developed in various periods and stages by Knothe (1957), Liu and Liao (1965), Brauner (1973a) and Marr (1975). This method is now widely used in various parts of the world. The physical models include sand (Litwiniszyn, 1959; Pariseau and Dahl, 1968) and gelatin (King and Whetton, 1958; Khair et al., 1986). They are used mainly to study the parameters that control subsidence behavior. The most popular numerical method is the finite element technique. It can simulate nearly every conceivable material behavior, inhomogeneity, bedding planes, anisotropy, and various boundary conditions. This versatility is absolutely necessary considering the ever-changing geologic and mining conditions encountered. In the following sections, only those methods that have been applied to US coalfields will be discussed. Furthermore, the methods for prediction of several key parameters such as maximum subsidence, maximum possible subsidence, and maximum displacement are discussed first, because they are the key parameters to be used in the profile function, influence function, and graphical methods.

Jan 1, 1992

By M. P. Meehan

The purpose of this paper is to present the key elements in a system; study of the electrical system for a timing and/or tilling operation. The ability of an electrical system to function in a reliable fashion at its proper levels is essential for an operation to be successful. A system study consists of a load study for determining the capability of the electrical network to provide power to the various loads and a short circuit study for determining the capability of the electrical protective equipment to properly protect against fault conditions. The sequence of events in a system study is data acquisition, determining the electrical parameters and analyzing the ability of the system to meet these requirements. If the system is small, herd calculations will be the manner in which the study will be conducted; if it is large then commuters will be used. A load study has as its objectives the determination of the capability and reliability of the source of power, transformers and conductors to satisfactorily deliver power to the loads at an acceptable voltage level. The Information required is a single line diagram showing the source, transformers, conductors and loads.

Jan 1, 1980

By J. C. Hower

The Hardgrove grindability index (HGI) is a widely used coal-quality parameter with applications in coal mining, beneficiation, and utilization. An understanding of the petrology of the coal is fundamental to understanding the validity of the HGI in the given application. The HGI varies with coal rank, increasing (greater ease of grinding) with increasing rank through the high-volatile bituminous rank range; and the HGI varies with changes in the maceral and microlithotype composition, decreasing with an increase in liptinite and liptinite-rich microlithotypes. In this review, the .fundamental relationship between HGI and coal petrology, and consequently its relationship to coal utilization, is examined.

Jan 1, 1999

By G. H. Matthes

Many mines, in particular coal mines, use inclines or slopes as an access to seam or seamlike deposits which outcrop at or close to the surface. In general, from the surface or from a certain depth, inclines or slopes follow the dip of the deposit with length up to 30,000 feet and by that going under an overburden cover of several thousand feet. The common outbye transport system for mine products is the conveyor. Material and men to be transported down into the mine are handled by rope driven systems when the angle of inclination exceeds the employment of locomotive traction. The transport volume can be sizeable and reach 200 to 300 tons of material and 500 men to be handled daily in a medium size coal mine with a production of 10,000 tons ROM.

Jan 1, 1986

By C. T. Thompson

"Rotary percussion" implies two types of energy, rotary and percussion. Into these categories fall rock' drills of varying sizes. The larger ones drill above 6" diameter holes; the medium size, 2 3/4" to 4 1/2" holes; and the smallest, 1 1/4" to 2" holes. Essentially, the larger holes are drilled with doom-the-hole drills using tri-cone bits. Percussion energy evolves from the drill piston and rotation power from the rotary table or overhead drive, using drill collars or pull down mechanism to preload the bit.

Jan 1, 1963

China's coal energy development, characteristics and relationships with atmospheric pollution are reported. Atmospheric pollution sources from coal combustion are analyzed. Some of the projects for clean coal combustion in the Shanghai area include use of industrial briquettes, investigation of coal combustion additives, and blending combustion of coal with industrial wastes. Coal is China's main energy source, and 80 percent of China's annual coal production is used in combustion devices. Coal-flue gases from the domestic stoves and industrial furnaces are the main atmospheric pollution source. China's atmospheric pollution is, in fact, the pollution of coal-flue gases. To 2000, in view of China's energy needs as a developing nation, the atmospheric pollution from coal combustion must receive our utmost attention.

Jan 1, 1994

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for all concerned people. The coal industry has taken great measures to reduce both types of pollution. Through the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. In many cases, the complete elimination of thermal drying by using centrifugal dryers to dewater fine coal products and meet customer specifications has completely eliminated air pollution from this source. To help eliminate stream pollution and the hazards created by tailing ponds, the coal industry is using centrifugal dewatering equipment. Use of centrifugals to dewater fine refuse for disposal would eliminate refuse ponds or extend their life. In doing this effectively and economically, preparation plants have the option of recycling the clarified water to close the water circuit or of discharging the water into receiving streams with the assurance that it contains an acceptable amount of refuse solids.

Jan 1, 1974

By Steve Garcia

GEORGE WEINMAN: Our next speaker is Steve Garcia, operations vice president and general manager of mining at IMC-Agrico, Florida. Steve was born in Lakeland, Florida, to an IMC mining family. He has 17 years with IMC-Agrico and Freeport companies, including assignments in North Carolina, Nevada, Arkansas, and Indonesia. His work within the industry includes technical and operating positions including chief metallurgist, drying superintendent, and mines operations manager at Pane Creek. Other experiences include design of a grassroots phosphate facility in North Carolina; construction and start-up of a gold facility near Elko, Nevada; work in the Blytheville, Arkansas, ammonia urea facility; and three years managing engineering, construction, and support services in Irian Jaya, Indonesia. Steve's presentation is "Evaluation and Standardization of Multiple Slurry Pumping Systems."

Jan 1, 1998

By R. L. Grayson

In 1995, the United States Congress abolished the Bureau of Mines in the US Department of Interior. But Congress preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the US Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the rnerger of the former Bureau of Mines with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data-informed" priority setting. This paper reviews the current surveillance information concerning the level of injury and disease from mining work and discusses how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 2000

By K. A. Natarajan, J. M. Modak, P. Anand

A microbial survey of Jamnagar bauxite mines in Gujarat, India, revealed the indigenous presence of a variety of autotrophic and heterotrophic bacteria and fungi associated with the ore body and water ponds in the vicinity. Among these, bacteria belonging to the genera Thiobacillus, Bacillus and Pseudomonas are implicated in the weathering of aluminosilicates; the precipitation of iron oxyhydroxides; the dissolution and conversion of alkaline metal species; and the formation of alumina, silica and calcite minerals. Fungi belonging to the genus Cladosporium can reduce ferric iron and dissolve alumina silicates. Biogenesis thus plays a significant role in bauxite mineralization. Various types of bacteria and fungi, such as Bacillus polymyxa, Bacillus coagulans and Aspergillus niger, were found to be efficient in significant calcium solubilization and partial iron removal from bauxite ore. Probable mechanisms in the biobeneficiation process are analyzed. Biobeneficiation is shown to be an effective technique for the removal of iron and calcium from bauxite ores for use in refractories and ceramics.

Jan 1, 1998

By John F. Spisak

Versatile living organisms, historically exploited as functionaries in the food processing, pharmaceutical and chemical industries, have not been successful in achieving similar or significant acceptance within the minerals industry. The current biotechnical revolution coupled with its expanded understanding, dictate that a flagging minerals industry reconsider the use of biotechnology in metallurgical applications. Living resources, either singly, in commensal association or in complex communities, are capable of duplicating fully integrated and complex processing functions. Organisms can mine and extract metals, detoxify chemical effluents and synthetically produce compounds. They have been criticized as exhibiting poor kinetics, excessive energy consumption and environmental sensitivity. However, expanding knowledge reveals that these organisms are surprisingly adaptable, variable and extremely durable. Applied biotechnology in specific cases offers favorable economic returns, environmental benefits and aesthetic value. Selective implementation of living systems can offer opportunities for reduced labor, increased productivity and technological advance. Success will not come easily. Capital must be risked, controversial decisions made and new ground plowed. Traditional, specialist thinkers will of necessity give way to interdisciplinary expertise and unorthodox methodology if success is to be achieved. Those who vigorously persevere, however, are likely to be rewarded with a dynamic and profitable new role in a restructured minerals industry.

Jan 1, 1985

By Salim Akhtar

The operation of a mineral processing plant with a complex flowsheet is represented by a mathematical operator. Such a representation permits a quantitative evaluation and monitoring of the separation processes in different sections of a processing plant, and gives an overall separation efficiency of the plant.

Jan 1, 1973

By D. W. Park

Longwall mining is considered to be the most efficient underground coal-mining technique in terms of coal extraction ratio, production rate and safety standards. Due to the increasing demand for higher coal production, the recent trends have been to use wider panels and to maintain a faster face movement. For these reasons, longwall mining can result in unexpected roof falls, excessive face convergence, shield damage and numerous maintenance problems, which can cause sudden interruption of coal production as well as serious safety hazards. Recent work at the University of Alabama has been dedicated to the development of a longwall strata-control and maintenance system that can integrate real-time shield monitoring, data presentation, analysis, forecasting and warning modules. This integrated system has been called LoSCoMS. The main objective of the system is to provide minute-by-minute stability and maintenance information such as the following: high-load, low-setting pressure, leg leakage, etc.; the analysis of various mining and geological parameters to determine past and present roof characteristics; and the forecasting of loading patterns for the following mining cycles, the next periodic weighting, etc. By using this unique system, mine operations personnel are well aware of past, present and future roof-loading patterns at the longwall face and, thus, proper safety measures can be taken ahead of time.

Jan 1, 1999