Search Documents

By Norm Steenson

Rapid excavation includes rapid support and is the central theme of this paper. Over the last few years, enormous strides forward have been made in the excavation and material handling aspects of underground excavation. However, the technology necessary to support these rapidly created openings has lagged behind the other aspects. This paper would attempt to bring you up-to-date on the progress made in bringing ground support using shotcrete into the same productivity rates as the other cyclic operations. Shotcrete has become an acceptable material for temporary and permanent support for undergound openings. However, coarse aggregate shotcrete has been an expensive construction material. It has been confined in the main to difficult ground conditions where conventional methods of support have proved to be even slower and more expensive than shotcrete. There are two main factors influencing the productivity of shotcrete equipment. (1) Structural shotcrete as opposed to gunite requires 40% to 45% rock minus 3/4" in the mix design. The equipment to handle such aggregate content has been difficult to develop on a volume basis owing to the attritional nature of the material which causes intense wear problems on

Jan 1, 1974

By R. Q. Honaker, D. Tao, D. Taulbee, B. K. Parekh

A significant amount of energy exists in the waste generated by the coal and timber industries. In the coal industry, the energy loss is mainly due to the discharge of fine coal to the waste impoundment. Despite the fact that the fine coal has the greatest cleaning potential, dewatering, handling and transportation concerns prevent its use as product in many cases. Likewise, the sawdust generated from wood production has energy value and is used as industrial boiler fuel when the transportation distance is relative short. However, wood waste is often discarded into cumbersome landfills due to uneconomical transportation alternatives. Recent research found that these two waste materials can be combined to provide a high energy fuel of around 13000 btu/lb that can be easily handled and transported to end users.

Jan 1, 2004

By Raymond S. Shrode

Limestone and dolomite production is of significant importance to the Baltimore and Ohio Railroad. Except for coal, more tons of limestone and dolomite are moved by the Railroad than any other mineral raw material. In the territory served by the Railroad, these materials are produced from every geologic system from Cambrian through Pennsylvanian. Some of the operations produce premium stone acceptable for high-specification steel and chemical use; at others, the stone finds application as aggregate materials and for cement manufacture. The Railroad is interested in seeing continued production from the operations it now serves, and in serving operations in a way mutually beneficial to the Railroad and to the producer. In working with producers, the importance of geologic knowledge in prospecting and development of deposits has been clearly recognized. In turn, knowledge of the economic and technological facets of production and consumption is needed for the geologists to participate with maximum efficiency.

Jan 1, 1966

By James Watson Baxter

Fluxes are used to promote pyrometallurgical processes that rely on adhesion (soldering or brazing) or fusion (gas and arc welding) to join metallic surfaces. In the adhesive processes, the metal surfaces to be joined are not melted; the join is formed using a filler metal with lower melting point than the base metal. Fusion welding involves use of heat in excess of the melting point of the base metal. The fused joint may be achieved either by simply fusing together metal surfaces brought in contact with each other or by introducing additional molten metal of similar composition to form a fused joint. ADHESIVE PROCESSES--SOLDERING AND BRAZING In order for molten filler metal, solder or braze, to spread in a manner that creates a successful join; the work surfaces on the base metal must be thoroughly cleansed. Fluxes remove stubborn oxide films and other surface contaminants, promote wetting of the work surfaces, add fluidity to the solder or braze, and enhance workability and ease of spreading. Brazing processes involve higher temperatures than those reached in soldering. Brazing fluxes, which must remain active and effective at the higher temperatures, differ from those employed in soldering. Some common fluxes used in adhesive processes are rosin for soldering tin and electrical connections, hydrochloric acid for use in soldering galvanized iron and other zinc surfaces, and borax for brazing. Soldering and brazing are similar processes, the primary difference being the temperature at which the joining operation is carried out. Soldered joints, produced with low-melting-point fillers (solders) that melt and flow at temperature less that 450°C (Althouse et al., 1988) can sustain loads of 1 to 1.7 MPa for extended periods of time (Anon., 1966). Brazing involves the use of filler materials with melting points commonly above 500°C and generally provides stronger joints than those obtained with solder. Both processes require local application of heat to melt and spread the filler so that the molten filler can wet (adhere to) the base metals by alloying and diffusion. Soldering Soldering is a means of joining metals by adhesion using a metallic bonding alloy as the filler, commonly a mixture of lead and tin. However, the adhesion of solder depends more on its ability to be keyed into minute surface irregularities than on alloying. The most familiar application is to provide and secure electrical connections. Soft solders can range from 1 to 70% tin with the remainder mostly lead. However, for general-purpose, soft-solder work, the alloy is commonly 50% lead-50% tin. Higher lead contents provide a wider range in the melting temperature and, for this reason, a 60% lead-40% tin alloy, which yields a mushy mixture, is used for wiped joints in lead sheet and pipe work. Conversely, 40% lead-60% tin alloys are used in soldering tin and other low- melting-point materials for which a narrower range of melting temperature is required. There are numerous other solder compositions such as tin-silver, 95% tin-5% silver and antimony-tin, 95% tin and 5% antimony (Carlin, Jr., 1992). Heat needed to melt and spread the solders is commonly provided by electrically heated, copper-tipped soldering irons or by means of torches; the solder is applied by hand, usually face-fed by means of wire. For wiped joints in plumbing and lead-cable splicing, the solder is manipulated with cloth pads. The molten solder wets the joint surfaces and is drawn, by surface tension, into minute fissures and capillary openings. Other applications involve use of induction heaters and furnaces with pre-shaped solder appropriately placed prior to fluxing and heating. In some processes, the joints are immersed in molten solder. Constituents and Role of Soldering Fluxes: Soldering fluxes generally fall into one of three categories: highly corrosive fluxes, intermediate fluxes, and noncorrosive fluxes. These same categories are sometimes designated inorganic, organic and rosin-based respectively (Althouse et al., 1988). Common constituents of each group are discussed briefly below. Corrosive Fluxes (Inorganic). Work with aluminum, magnesium, stainless steel, high alloy steel, aluminum bronzes, and silicon bronzes is carried out at temperatures in the upper portion of the range for solder operations. Soldering these materials requires use of highly active, corrosive fluxes to remove and prevent the formation of the especially stubborn, hard, oxide films that form on these materials upon exposure to the atmosphere. The corrosive fluxes consist of inorganic acids and salts that are applied either as pastes or dry. They are active at elevated temperatures and, since they remain active after the soldering is completed, must be completely removed. The main constituent of most corrosive fluxes is zinc chloride with a melting temperature well above the solidus temperature of most commercial tin-lead solders. It is made by the action of hydrochloric acid on zinc. When zinc chloride is used alone, un- melted particles of this corrosive salt get caught up in the joint and weaken it. For this reason, other inorganic salts such as ammonium chloride (NH4Cl) or sodium chloride (NaCl) may be added to lower the melting temperature. A mixture of zinc chloride and ammonium chloride is very effective because the excellent oxide reducing properties of ammonium chloride and the protective action of the molten zinc chloride combine to produce a fluxing action superior to that achieved when either is used alone. In addition to zinc chloride, ammonium chloride, and sodium chloride; common con-

Jan 1, 1994

By S. K. Kawatra, T. C. Eisele

Microorganisms, such as the bacteria Thiobacillus ferrooxidans, have been reported to depress pyrite flotation (Elzeky and Attia, 1987; Atkins, 1990). However, the depen¬dence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms (chemolithotrophic bacteria, chemoorganotrophic bacteria and yeast) over the pH range of 2 to 12 was studied. Screen¬ing tests using microflotation showed that every microorgan¬ism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with both mineral pyrite and coal pyrite using Thiobacillus ferrooxidans and Saccharomyces cerevisiae as depressants, showed that these microorganisms are very effective depressants for mineral pyrite at acid pH, but they are largely ineffective at neutral and alkaline pH, where the mineral pyrite surface is not naturally hydrophobic. The flotation response of the coal pyrite was completely different from the mineral pyrite. The coal pyrite was most floatable near neutral pH, with the floatability decreasing in acidic or alkaline solutions. De¬pression of the coal pyrite by yeast was not selective between the pyrite and the associated coal under the experimental conditions.

Jan 1, 2000

By Zhang Zhitie

The limitations in mechanism research of mineral comminution in the past and the basic features of the comminution process have been analyzed. Two kinds of catastrophe model, i.e., cusp model and swallowtail one in the mineral comminution have been put forward. The dissipative structure of the mineral comminution: entropy production rate, extra entropy, extra entropy production and system stability has been discussed. The physical nature of the behavior that an old structure was destroyed and a new one was produced in the mineral comminution process has been brought to light.

Jan 1, 1995

By Belinda F. Arbogast

Reclaimed mine sites have been evaluated so that the public, industry, and land planners may recognize there are innovative designs available for consideration and use. People tend to see cropland, range, and road cuts as a necessary part of their everyday life, not as disturbed areas despite their high visibility. Mining also generates a disturbed landscape, unfortunately one that many consider waste until reclaimed by human beings. The development of mining provides an economic base and use of a natural resource to improve the quality of human life. Equally important is a sensitivity to the geologic origin and natural pattern of the land. Wisely shaping our environment requires a design plan and product that responds to a site's physiography, ecology, function, artistic form, and public perception. An examination of selected sites for their landscape design suggested nine approaches for mining reclamation. The oldest design approach around is nature itself. Humans may sometimes do more damage going into an area in the attempt to repair it. Given enough geologic time, a small-site area, and stable adjacent ecosystems, disturbed areas recover without mankind's input. Visual screens and buffer zones conceal the facility in a camouflage approach. Typically, earth berms, fences, and plantings are used to disguise the mining facility. Restoration approaches the best land use as restoring to its original condition. Rehabilitation targets social or economic benefits by reusing the site for public amenities, most often in urban centers with large populations. A mitigation approach attempts to protect the environment and return mined areas to use with scientific input. The reuse of cement, building rubble, and macadam meets only about 10% of the demand for aggregate. Recognizing the limited supply of mineral resources and encouraging recycling efforts are steps in a renewable resource approach. An educative design approach effectively communicates mining information through outreach, land stewardship, and community service. Mine sites used for art show a celebration of beauty and experience-abstract geology. The last design approach combines art and science in a human-nature ecosystem termed integration. With environmental concerns, an operating or reclaimed mine site can no longer be considered isolated from its surroundings. Site analysis of mine works needs to go beyond site-specific information and relate to the regional context of the greater landscape. Understanding design approach can turn undesirable features (mines and pits) into something perceived as desirable by the public.

Jan 1, 1999

By Gail Moulton

Searles Valley is located approximately 125 miles northeast of Los Angeles in the Basin and Range Province. Occupying the lowest part of the valley is Searles Dry Lake Playa, which is about 9 miles long and 7 miles wide. Three major subsurface evaporite horizons have been identified and are termed from bottom to top, the Mixed Layer, Lower Salt and Upper Salt. The evaporite beds were formed by desiccation of runoff from the eastern Sierra Nevada during Quaternary time. The saline beds are generally brine saturated with the important ions being sodium, potassium, carbonate, bicarbonate, sulfate, chloride and borate. These ions are present in the brines in various concentrations and have combined to form the minerals halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, sulfohalite, glaserite and others. North American Chemical Company selectively pumps the interstitial brines to feed their chemical plants located on the western edge of Searles Lake. Minerals have been mined since 1873, beginning with borax and trona scraped from the surface. Brine processing began in 1914 with potassium chloride and borax recovery. Expansions have added sodium sulfate and soda ash to the product mix. Currently, dredging of trona ore is also taking place.

Jan 1, 1995

By Staff

GENERAL DESCRIPTION The Lucky Friday mine is located in Mullan, Sho-¬shone County, Idaho. The mining method is horizontal slice cut-and-fill (with timbering for support or un¬timbered) using hydraulic sand. Cemented sand fill at a 1:17 ratio is used in sill pours and at a 1:7 ratio for the final 152 mm (6 in.) capping in successive stope floor pours. Annual production with 100% cut-and-fill mining is 167 829 t (185,000 st). The average depth of mining is 1296 m (4250 ft) and the average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size The ore body is 396 to 488 m (1300 to 1600 ft) long on strike, 1421 m (4660 ft) on dip, with an average width of 2.3 m (7.5 ft). Dip varies from vertical to1.2 rad (70°) Ground Conditions, Ore Value, and Production Requirements The ore body contains quite strong argentiferous galena and quartz. The hanging wall and footwall are strongly sheared and fractured. Ore value is $211/t ($192/st).

Jan 1, 1982

By Peter L. Dunn

With the advent of new high-strength magnetic materials, rare-earth magnetic separators have become more common place for processing heavy mineral sands. In many instances, rare-earth magnets have replaced conventional separators such as electromagnetic cross-belt and induced-roll type machines. This paper will present the results from a detailed test program developed to evaluate the performance of rare-earth drum and roll separators for processing heavy mineral sands. The effect of machine design parameters, such as magnetic element configuration and separator diameter, will be reviewed in light of these test results. The impact of basic operating parameters (i.e. feed rate and roll speed) on separation efficiency will also be presented.

Jan 1, 1999

By Todd L. Hollingsworth, Jeremy K. Hobbs

In 2001, the Radomiro Tomic Mine located near Calamq Chile, added a tertiary crushing facility. An 84" wide mobile tripper is used to fill their tertiary crushing storage facility. This paper is a we study to demonstrate the drive and control systems in use on the tripper. Of special note is the design concept used to allow the system to operate multiple motors in both demand and regenerative modes through a single VFD. Also noted is the use of touch screen local controls, handheld radio controls, starting/stopping/ braking philosophies, safety device interfaces, and the local to remote control interface.

Jan 1, 2004

By Ross R. Bhappu

In 1989, William A. Vogely created the Mineral Economics and Management Society (MEMS). He did this after SME disbanded the Minerals Resource Management Committee, a group dedicated to technical programming of minerals economics and management issues. A few years later, SME reinstated this committee. MEMS held its fourth annual conference "Mineral resources: Managing dilemmas and opportunities," in Boulder, CO March 9-11, 1995. Some of the MEMS programs are similar to the Minerals Resource Management Committee programs. However, MEMS conferences cover more diverse issues. These include minerals policy, environmental legislation impacts on the minerals industry and minerals economics issues. The 1995 MEMS conference included six sessions and three distinguished speaker addresses. Papers topics included US and Canadian mineral policy, financial strategies for managing mining companies, Latin American mineral investment opportunities, quantitative economic modeling and the impact of environmental interest groups on the minerals sector in the United States and Canada. One session was dedicated to students who competed for $1900 in prizes for outstanding papers.

Jan 1, 1995

By P. Somasundaran, D. R. Nagaraj, Jing Wang

Polysaccharides have been widely used as depressants in mineral processing for decades. They constituent one of the most abundant family of biopolymers. However, only a small number of them have been used by industry so far because of a general lack of understanding of interactions between these polymers and minerals. In this work, adsorption tests, electrophoretic mobility measurements, microflotation and fluorescence spectroscopic tests were performed along with computer simulation to explore the mechanistic aspects of guar gum adsorption and conformation on talc as a function of relevant variables such as ionic strength, pH, solvent composition and polymer molecular weight. From microflotation tests, it was found that talc hydrophobicity decreased markedly due to the adsorption of guar gum even at very low concentrations and reached a plateau below moximum adsorption. Guar gum adsorption on talc was found to be not affected significantly by changes in solution conditions such as pH and ionic strength, ruling out electrostatic force as controlling factor for adsorption. Fluorescence spectroscopic studies showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Also urea, a hydrogen bond breaker, reduced the adsorption of guar on talc. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding in preference to electrostatic or hydrophobic force. This information should help toward designing reagents of optimum molecular architecture for efficient depression, dispersion or other such surface modification of particles.

Jan 1, 2005

By S. Zhou

Since the hypothesis of coal and methane outburst mechanism based on elastic mechanics gives no consideration to time, it can not give a satisfactory explanation to the outburst occurrence and its development. A creep mathematical model of coal containing gas has been set up through creep tests and analysis under the condition of tri-axial compression. And the model can explain the phenomena of coal and methane outburst successfully. The tests proved that there is no essential difference between the rheological properties of prone outburst coal and non-prone outburst coal. Outburst can take place in any kind of coal if the rheological conditions of coal containing gas are met. The creep mathematical model provides a basis for establishing a comprehensive index of coal and methane outburst possibility.

Jan 1, 1991

By Ralph Bernstein

The processing of earth observation sensor data by digital technology is almost two decades old. Only recently, however, has this technology become practical and economical. The reasons for this are interesting to analyze, and they provide some insight into what the future may bring. Some of the earlier activities and their limitations, current systems and their applications, and future technology direction are summarized.

Jan 1, 1979

By J. Brent Hiskey, Srini Raghavan

The physical chemistry of dissolution of silicate and complex oxide ores in aqueous lixiviants has been reviewed. Particular attention has been paid to the analysis of dissolution mechanisms and kinetic models and to the elucidation of the role of the porous nature of the materials on dissolution behavior. Importance of the physico-chemical characteristics of the leach residues on leaching efficiency has been discussed.

Jan 1, 1989

By G. Kazonich, S. L. McGill, J. W. Walkiewicz

Naturally occurring minerals and reagent-grade compounds were tested to determine their receptivity to microwave heating. The maximum temperature achieved for the samples and the time required to reach temperature are reported. A description of the microwave oven and a thermocouple technique that accurately measures and continuously records the temperature of samples during irradiation are reported. Extractive applications using the generated microwave data were investigated. Stress fracturing at mineral grain boundaries in a gangue matrix was shown. This should significantly affect grinding energy requirements and liberation properties. A method to produce a magnetic phase on pyrite surfaces, a method of using microwave heating to retort cinnabar concentrate, and a roast-leaching microwave treatment of chalcopyrite ore are described.

Jan 1, 1987

By P. Bissert, L. Yan, D. Yantek

"Federal regulations require refuge alternatives (RAs) in underground coal mines to sustain life for 96 hours while maintaining an apparent temperature (AT) below 35°C (95°F). NIOSH research has shown that heat and humidity buildup is a major concern with RAs because they have a limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding an RA is very complex and is not easily defined analytically nor experimentally. To investigate heat and humidity buildup in RAs, NIOSH conducted multiple in-mine 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA. The test results show that when moisture was introduced into the tests to represent perspiration and respiration from miners (wet tests), the average measured internal air temperature at midheight increased by 7.7°C, 9.4°C, and 10.5°C, and the RH approached 95%, 94%, and 88%, respectively. For the dry tests when no moisture was introduced, the average internal temperature increased by 8.4°C, 10.3°C, and 12.6°C, respectively. INTRODUCTION If an accident occurs in an underground coal mine, miners who cannot escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the thermal environment inside the RA. The metabolic heat of the occupants and the heat released by the CO2 scrubbing system will cause the interior air temperature to increase. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The internal thermal conditions can subject miners to heat stress, which can lead to heat exhaustion, heat stroke, or even death depending on duration and magnitude of exposure. MSHA regulations require that RAs must be designed to ensure that the internal apparent temperature does not exceed 35°C (95°F) when the RA is fully occupied [1]. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Before a mobile RA can be deployed at an underground mine for emergency usage, it must be tested to show that its internal AT when fully occupied will not exceed the 35°C (95°F) limit. For practical reasons, RA manufacturers usually conduct their tests at above-ground test facilities. To investigate RA thermal response in an in-mine environment, NIOSH conducted multiple 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA in its underground coal mine facility. The work described in this paper could be used by RA manufacturers to determine a final temperature rise based solely on dry and time-reduced testing."

Jan 1, 2017

By V. Srajer

This paper deals with the problem of efficiently selecting the most appropriate loading and hauling equipment for surface mines. Problems and factors that affect productivity and operating cost are identified. During the course of collecting the information for this study, mining companies and equipment manufacturers were interviewed to define their selection practices. The majority of mining companies prepare general specifications and ask the suppliers to mate those specifications to their product line. The mining company then evaluates various proposals on the basis of the best available deal. The following 'mines from western Canada provided information for this study: Coal Mountain, Line Creek, Quintette, Westar's Harmer mine from the Province of British Columbia, and Coal Valley, Gregg River, Highvale, Luscar from the Province of Alberta.

Jan 1, 1989

By Tench C. Page

The Yarnell gold deposit is located 1.5 km (1 mile) south of Yarnell in the Weaver mining district of Yavapai County, AZ (Fig. 1). Elevations within the area of the deposit range from 1400 to 1560 m (4590 to 5120 ft). Historic production, principally from quartz veins localized along the Yarnell fault, was about 200 kt (220,000 st) at an average grade of 6.9 to 10.3 g/t (0.2 to 0.3 oz/st) gold. The federal government closed the mine in 1942 due to World War II. Norgold Resources Inc. leased the property in 1988 and joint ventured it with Asarco the same year. Asarco drilled 7822 m (25,660 ft) in 96 reverse circulation and four diamond drill holes and identified 8 t (260,000 oz) gold reserve. IBema Gold Inc. acquired Norgold in 1991 and is currently permitting the project. Production is expected to begin within the next two years

Jan 1, 1994