Search Documents

By Jianmin Qin, R. V. Ramani

The major parameters affecting dust flow at a longwall face are dust generation rate, air velocity and quantity distribution at the face, and the characteristics of the dust such as particle size distribution, density etc. Previous studies have identified the longwall shearer as the major source of the airborne dust in the faces. In this study, the effects of dust generation rate and shearer speed on the levels of ambient dust concentration are investigated. A series of experiments were performed under controlled conditions in a full scale simulated longwall face at the Lake Lynn Laboratory mine of U.S. Bureau of Mines using characterized bituminous coal dust. A trickle-duster was moved up and down the longwall face to simulate the shearer. In each experiment, a known amount of dust was dispersed by the trickle-duster into the air and the average dust generation rate was calculated. At the same time, gravimetric respirable and total airborne dust samples were collected and air velocity measurements were made along the face. The experimental conditions, data, and results are presented and discussed in this paper. The airborne dust concentration and air velocity data indicate that the concentration increases and air velocity decreases with distance from headgate for the first half of the face. Towards the tailgate, the air velocity increases with increasing distance but the dust concentration levels off with some variations. The data show that a higher dust generation rate results in higher dust concentration levels. More importantly, the data show that the rate of increase of airborne dust concentration is higher than that of dust generation rate. For the same air velocity distribution and dust generation rate, lower speed of the dust source results in higher airborne dust levels at the face.

Jan 1, 1991

By Warren D. Stanford Stanford

Introduction The Sleeper mine is a near-surface gold mine located in a remote area 56 km (35 air miles) northwest of Winnemucca, NV (Fig. 1). The deposit was discovered in 1984 by an Amax exploration geologist. Favorable drilling results led to feasibility studies and metallurgical testwork. Final evaluation of the mine potential proceeded very quickly. The project received Amax board approval in July 1985. Eight months later, the process plant was fully operational. The first gold ($1 million) was shipped one month later, in March 1986. Total plant capital was $27 million. Payback was achieved in six months. The Sleeper mine was expected to produce 1.6 t (53,000 oz) of gold and 1.3 t (41,000 oz) of silver annually. However, the ore body exceeded all expectations. Production for the first 10 months of operation amounted to 4 t (128,000 oz) of gold and 2.9 t (94,000 oz) of silver. Direct cash operating costs are in the $1.77/g ($55 per oz) range. Amax is actively conducting exploration nearby for additional reserves to extend the mine's life. (See update on page 242.) Geology The Sleeper gold deposit is located on the northwestern flank of the Slumbering Hills and in the Awakening Mining District. Rocks exposed in the vicinity of the deposit are interbedded siltstones, sandstones, and limestones of Triassic age. They are overlain by latite lava flows and tuffs of Tertiary age. Dikes and sills of latite and andesite intrude the sedimentary rocks. Quaternary deposits of mostly sand with minor gravel and clay cover a pediment containing the gold deposit. The sedimentary and volcanic rock units have been transsected and offset by extensive north- northeast trending faults and less abundant northwest trending faults. Both fault systems fractured and prepared the ground for subsequent invasions of mineral-bearing hot spring geothermal waters. The hot spring systems produced widespread hydrothermal alteration and gold mineralization at silicified centers near feeder fault structures. The deposit is hosted by siltstone and latite that have been hydrothermally brecciated. The main breccia is elongated north-northeasterly. The hydrothermal breccia zones appear to dip steeply to the west. Gold mineralization consists of native gold and electrum deposited in two or more high-grade quartz-breccia veins. Lower grade gold mineralization occurs

Jan 4, 1987

By W. C. Wheeler, G. Suranyi, J. F. Gentleman, J. Muller, R. Kusiak

INTRODUCTION In 1974 two of the present authors reported the results of a pilot study indicating an increase of lung cancer risk in Ontario uranium miners. (Muller, Wheeler, 1973, 1974) The study was based on data contained in a computerized Mining Master File maintained by the Ontario Workmen's Compensation Board that contained information on miners examined in Ontario who had either 60 months of dust exposure in mines or had signs of pneumoconiosis or tuberculosis. Including the above conditions the definition of uranium miners added the condition of one month or more of uranium mining experience in Ontario. This list of Ontario uranium miners contained 8,649 names. Following the results of this first pilot study, we embarked on creating a file of uranium miners containing information on men with one month or more of uranium mining experience in Ontario without any further conditions. This file was used by the Royal Commission on the Health and Safety of Workers in Mines in their study of risk in Ontario uranium miners. (Hewitt 1976) This file contained 15,094 names. In this report we give an outline and progress report on a study of Ontario miners that we are conducting at present. It was felt that the male population of Ontario is not necessarily an adequate control population for uranium miners. A preliminary examination of the work history of uranium miners indicated that the majority of them (about 90 percent) had other mining experience in addition to their exposure in uranium mines. We therefore considered it useful to evaluate the possible effects of non-uranium mining on risk, and for this reason decided to make the Uranium Miners Study part of a study dealing with the mortality of Ontario miners in general. Aims of the Study The aims of the Study include the evaluation of: 1) the risk of dying by cause in non-uranium miners as compared to the male population of Ontario and Northern Ontario. 2) any differences that might exist in the death experience of non-uranium miners by cause according to ore mined. 3) the effect of length of exposure in non-uranium mines on age-specific risk by cause. 4) the dose-response function for primary cancer of the trachea, bronchus and lung from exposure to radon and its short-lived daughters. 5) the possible effect of the mining environment on deaths from causes other than cancer of the trachea, bronchus and lung. The study will address itself to a number of other factors that might well affect the dose-response function. These include: a) factors in the mine environment - other than radon daughters - that might affect lung cancer mortality. b) the effect of non-uranium mining on lung cancer risk in uranium miners. c) the effect of age as well as age at time of exposure on lung cancer risk. d) questions of latency and the possible dependence of latency on age at time of exposure. e) smoking as an important factor in lung cancer risk. f) Histological type of cancer in relation to the various parameters of exposure and age. MATERIALS AND METHODS The Study is making use of existing computerized data files and has set up certain new files. These include the Mining Master File and the Model Development File. The Mining Master File This file is a computerized record of data on individual miners obtained at yearly miners' examinations that have been carried out since the mid 1920's. The conditions for inclusion in the Mining Master File have been indicated above. Information contained in the file includes: (1) Identifying information: a) Surname and given names b) Date and place of birth c) Miners Certificate Number d) Social Insurance Number if available. (2) Updated Employment data obtained at each miner's examination: a) Year of first dust exposure in Ontario b) Year of first dust exposure outside Ontario c) Number of months worked in mining d) Ores mined e) Mining areas and mines f) Occupations

Jan 1, 1981

By Augusto Andres Torres Toledo, João Felipe Coimbra Leite Costa, Luciano Nunes Capponi, Diego Machado Marques

Short-term mine planning to open pit requires defining diglines to orientate the excavation geometry. In deposits with multiple chemical variables, it is necessary to have more rigorous control over the feeding of the processing plant. This study analyzes the impact of incorporating multiple chemical variables, the risks generated by geological uncertainty, and the number and starting point locations of shovels in the sequential design of diglines. The objective is to maintain and preserve the low-grade variability, required tonnage, and continuity in sequentially selecting blocks. To achieve this, the probability distribution function of each chemical variable is used while attempting to maintain the ore grades as constant as possible. As it is difficult to maintain multiple elements with low variability simultaneously, the relevance of each chemical variable in the economic benefit is identified. Weights are assigned to signal the importance of each element based on its significance in the recovery process. Several diglines, consisting of sequential blocks, were generated on the same seed point to meet the weekly ore demand. Optimizing the stationarity of multiple chemical variables, accessing and reducing the geological uncertainty performed through geostatistical simulation of grades and transfers functions, considering the number and location of shovels, while meeting the operational restrictions of the selected blocks. The optimized digline with the multiple grades as stationary as possible is retained. The process is illustrated in a phosphate mine. The results show that the proposed method is viable and allows for a quick solution.

Jun 25, 2023

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By Roy M. Fleming

During the decade of the 1970's, a new emphasis was placed on assuring a safe and healthful workplace for all American workers. Much of the basis for this national effort was federal legislation: the Occupational Safety and Health Act of 1970 and the Federal Mine Safety and Health Act of 1977 (amended from the 1969 Coal Mine Act). One of the agencies involved in this protection effort is the National Institute for Occupational Safety and Health (NIOSH) of the Centers for Disease Control (CDC) in the Department of Health and Human Services (DHHS). In fulfilling its mandates under the 1970 and 1977 Acts, NIOSH conducts research, experiments, and demonstrations to support and stimulate advancements in health and safety practices. Priorities for NIOSH research are established primarily through congressional mandates, requests from the Department of Labor, needs as defined by NIOSH researchers, and surveillance information. Emphasis is placed on research in the areas of toxicology, industrial hygiene, physical and chemical sciences, physiology, ergonomics, engineering, psychology (behavior and motivation), and epidemiology (industry-wide studies). The framework of the current Institute program to identify, evaluate, and control occupational hazards includes activities in surveillance, research, evaluation, and training. These activities are planned and evaluated through a system that coordinates the efforts of eight research and scientific divisions. Each division develops projects to address program areas that have been identified by NIOSH management as having highest priority. In surveillance programs, the objectives are to identify substances and agents found in a representative sample of workplaces and to collect and evaluate information on rates of disease and injury in occupational groups. Information is also collected on occupational safety and health programs implemented by industry. Estimates of worker exposures and the potential for adverse health effects are considered in setting priorities for further investigations. A related activity, which also serves to provide technical assistance to industry, is NIOSH's Health Hazard Evaluation program. On-site investigations of workplaces are made in response to worker, employer, or government agency requests. Both industrial hygiene and medical examinations are conducted, and the results contribute to identifying new problems and evaluating their significance which may have public health implications beyond the particular worksites that are investigated. Field and laboratory research projects are performed to meet several objectives: - Characterize the working environment by evaluating current and past exposure levels for workers who are included in epidemiological or medical investigations. - Develop epidemiological information to define the association between the substance or agent under investigation and the acute and chronic health effects on workers. - Determine through animal studies the parameters of an association between exposure and effect. - Investigate the etiology of disease. - Develop sampling and analytical instruments and techniques and demonstrate their application for measuring toxic materials in the workplace. - Formulate sampling strategies that will accurately and precisely indicate exposure levels. - Develop medical procedures to prevent disease and to detect the presence of disease and early indicators of disease. - Assess the technology for control of exposures, including engineering and administrative techniques, personal protective equipment, and work practices. Presently, the research program is focused on reproductive effects, neurotoxic effects, injury/trauma, lung disorders, cutaneous disorders, cardiovascular disorders, cancer, stress-related disorders, effects of physical agents, digestive disorders, and renal and other organic disorders. In studying these issues, priorities are determined by the seriousness of possible adverse health effects resulting from occupational exposures, the feasibility of studying existing records or obtaining new data, and the size of the population which is potentially affected. Where there is low level of suspicion concerning adverse health effects or where an occupational disease occurs in a variety of industrial environments, investigations are limited to gross analyses of health effects such as review of mortality patterns. In such studies, the industrial populations selected are those for which existing data resources can be utilized. Such data consists of records of occupational exposures or health status which have been maintained by the employer, the union, or Government agencies. Where a review of the available information suggests that serious health hazards exist and the existing data resources are inadequate for quantifying the relationship between the specific biological response and type and degree of exposure, prospective studies are initiated. Information derived from such research is essential for the development of sound criteria for control of industrial exposures to noxious agents. Other input to the criteria documentation process comes from searching and evaluating the literature. Criteria documents contain the recommendation of an environmental limit where information is available to support it, as well as the recommendation of work practice controls, medical evaluation, information for workers to recognize and avoid the hazard, and identification of specific research gaps. In some cases, during the criteria document preparation, gaps in knowledge are found which necessitate further research before an occupational standard can be recommended.

Jan 1, 1981

By Yasushi Arai

"Among Tokyo Metro’s approximately 200km of subway lines, the Tozai Line that connects Chiba Prefecture and mid-Tokyo experiences congestion of up to 199% at worst and relief of this has become urgent. Therefore, as it is imperative to increase the number of trains operating in the exceptionally congested area from mid-Tokyo going east, a large-scale renovation work is planned between Iidabashi Station and Kudanshita Station that will facilitate turn-back via 3 tracks. While ensuring the safe and stable operation responsible for about 1.35 million passengers daily, this highly difficult work of inner wall demolition and reinforcement of the side walls and floor slabs will only be implemented for 3 hours during late night. This paper discusses large-scale plans to improve turn-back facilities, and the methods of construction therein as an example of operational improvement of a subway network. 1) INTRODUCTION The Tokyo Metro Tozai Line (“Tozai Line”) opened over the entire 30.8 km distance from Nakano to Nishi-funabashi on March 29, 1969. It has the longest operating length of the nine Tokyo Metro lines, and was the first subway line to extend past the borders of the Tokyo Metropolis. Through train services with two other railway companies are available from the Tozai Line. Tozai Line trains join the Sobu Line of the East Japan Railway Company (“JR East”) and the Toyo Rapid Railway Line of Toyo Rapid Railway (“TR”) from Nishi-funabashi Station, and the JR Chuo Line from Nakano Station. The line is structurally distinctive in that 51% of it was built using the open-cut method, 43% of it is elevated and the remaining 6% was built when we used the shield method for the first time 1)2)3)."

Jan 1, 2016

By L. Alan Weakly

This paper was presented at the ‘17th U. S. Symposium on Rock Mechanics’ on August 29, 1976, at Snowbird, Utah, at the SME-AIME Fall Meeting on September 1, 1976, at Denver, Colorado, and at the Polish-American conference on Ground Control in Room-and-Pillar Mining on August 7, 1980 at Southern Illinois University, Carbondale, Illinois. Introduction The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement- fly ash mortar. Although the fully bonded bolt concept is not new as exemplified by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1)(2)the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation's Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since Decmeber of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the group-rebar system.

Jan 1, 1982

By L. Alan Weakly

At a time when the US mining industry is struggling to emerge from a lengthy recession, the burden of new, unnecessary regulations could shorten the life of, or be fatal to many domestic mining companies. The possibility of new restrictions on the use of diesel equipment operating in underground mines is one example of unnecessary regulations. These could cause serious harm to the economic health of many mining companies. Whether future health-related Mine Safety and Health Administration (MSHA) regulations restricting the use of diesel equipment are unnecessary, depends on whether these restrictions are supported by fact or created in a political environment. The mining industry has benefited from the use of diesel equipment in underground metal-non-metal and coal mines for more than 50 years. Since first introduce to underground mines in the early 1940s, the use of diesel equipment has grown in numbers and size. During this time, the mining industry in America has achieved much higher productivity rates and improved safety. Although all these gains cannot be attributed to the greater use of diesel equipment, a high percentage can be. I began my professional mining ca¬reer in 1970 working in the Missouri lead mines. At that time, the use of diesel equipment was well established in metal-non-metal mines throughout the United States and many parts of the world. As director of mining research for St. Joe Minerals Corp. (now The Doe Run Co.), I was involved in research to improve mining productivity and safety. This involved investigating the better and safer use of existing or new mining methods, products, equipment and people. Within this group, diesel equipment had the single largest positive impact.

Jan 1, 1993

By Neil J. Dahmen, Howard J. Handewith

INTRODUCTION Tunneling machines were introduced into civil con¬struction in the 1800s, but their practical applications were not realized fully until the 1950s. As of 1977, tunneling machines were being used on most tunneling projects of substantial size. As in civil construction, the mining applications of tunneling machines have included long drives such as tunneling for long ore-body develop¬ment drifts, long haulage tunnels, longwall access drifts, and long crosscut developments. Tunneling machines ranging from 1.75-m (5.7-ft) to more than I1.0-m (36-ft) diam are available from several manufacturers; machines for mining applications generally have ranged between 1.75 and 6.0-m (5.7¬and 20.0-ft) diam. Tunneling machines usually operate at or near horizontal grades and are supported by a rail-haulage backup system. However, declines and inclines have been made using alternative backup equip¬ment. Either circular or shaped tunnels may be bored, depending upon the particular equipment used. Using tunneling machines to bore openings through rock offers several advantages over the use of the drilling and blasting technique. These advantages include a rapid advance, continuous operation, uniformity of the opening size, smooth walls, and safe working conditions. Compared to drilling and blasting, boring reduces the disturbance of adjacent rock, thereby reducing the ground-support requirements and the exposure to water inflows. The smooth walls provide natural arching and present minimum resistance to the flow of air. A tunneling machine should be considered a spe¬cialized mining tool that is well-suited to certain mining applications. Properly applied and sustained, a tunnel¬ing machine contributes to realizing substantial econo¬mies in the development of underground mines. All costs herein are expressed in 1977 US dollars, unless otherwise noted. The mention of trade names and manufacturers is not intended to imply an endorse¬ment of any specific equipment. TYPES OF TUNNELING MACHINES As listed in Table 1, five principal types of tunneling machines were being manufactured in 1977. Each type of machine offers a special solution to a specific mining problem. Although each of these types of machines is described herein, most of this chapter is devoted to the full-face rotary rock-tunneling machine that has demon¬strated the greatest production in both civil construction and mining applications. Full-Face Rotary Rock-Tunneling Machines As shown in Fig. 1, a full-face rotary rock-tunneling machine consists of a rotating head that is fitted with rock-cutting tools and is forced into the tunnel face. This head is supported by a bearing on a structural support member that, in turn, is held in place by a hydraulically positioned wall-gripping mechanism. Both torque and thrust are reacted from the cutterhead, through the structural support and gripper mechanism, and to the tunnel wall. The rock cuttings fall to the invert at the tunnel face, and they are removed by means of cutterhead buckets or scoops that transfer the cuttings to a conveyor belt. After advancing the cutter¬head through a preset boring stroke, the tunneling machine is advanced by hydraulically pulling the gripper mechanism in from the tunnel walls, stroking forward, and resetting the gripper to the new forward position on the wall; the machine then is set for the next advance stroke. Full-face machines cut only circular openings. Ma¬chines with diameters as small as 1.8 m (6 ft) and as large as 6.1 m (20 ft) have been used in mining applica¬tions, excavating rock with unconfined compressive strengths in excess of 276 000 kPa (40,000 psi). Although special machines have been designed to turn on a radius of 30 m (100 ft) in both horizontal and vertical directions, the conveyors and backup sup¬port equipment generally limit tunneling machines to turns with a radius of more than 60 m (200 ft). The full-face rotary rock-tunneling machines have provided the fastest and most reliable production of any mining method or machine. These machines can be equipped to place any of a variety of ground-support systems, and they can be provided as "open" machines, as shown in Fig. 1, or as "shielded" machines, as shown in Fig. 2. The open machines have the advantage of allowing the ground to be supported as near to the tunnel face as possible. The shielded machines have been designed principally to allow placing precast con¬crete segments. The shielded machines completely pro¬tect the equipment and personnel at the heading, but they are economically limited to permanent long-life haulageways where full lining is required. Partial-Face Rotary Rock-Tunneling Machines As shown in Fig. 3, the partial-face rotary tunneling machine is equipped with a cutterhead that rotates slowly at about 0.21 rad/s (2.0 rpm). The single-disk cutterhead produces the tunnel section shown in Fig. 4 by means of an oscillating motion. These machines work on the undercutting principle, and they are avail¬able in spring-line dimensional increments of 0.1 m (0.32 ft) from 1.5 to 2.1 m (5.0 to 7.0 ft); the vertical dimensions are 2.4 to 3.2 m (8.0 to 10.5 ft), respec¬tively. Depending upon the tunnel width, the cutterhead disk may be fitted with from 8 to 16 drag-bit cutters. Penetration is achieved by means of hydraulic rams that force the tungsten-carbide bits into the rock mass. The operation is cyclic, with cutting occurring only on the upstroke. On the downstroke, the rotating cutter¬head draws the fallen muck from the invert into the panzer-type conveyor for rearward transfer. This feature allows time to either reposition ore cars or to exit the tunnel with muck trains while the machine is cutting, as shown in Fig. 5. Boom-Type Rotary Excavators The boom-type rotary-excavator tunneling machines commonly are known as boom-type continuous miners

Jan 1, 1982

By M. E. Poad

The Research and development review arrived too late to appear in the May issue. The competitiveness of the US mining industry in a world market depends on many factors. The introduction of new and innovative methods, though, can have a significant, long-term impact. As industry cuts back its own long- term research and development efforts, the federal government continues to provide the major support for mining and minerals research. The US Bureau of Mines works with the mining industry and the academic community to develop innovative concepts for the mining and processing of non-fuel minerals. The Bureau’s research focuses on exploration and mining technology, minerals and materials science, processing technology, health and safety and environmental technology. Mine design A conical caving system, being designed by the Bureau, would allow the development of low-grade ore bodies, early startup at lower initial capital costs and increased safety and versatility in development and production. This method is a form of mass caving that allows the ore to be drawn from a central loading point at the bottom of the cone- shaped caving zone (Fig. 1). A simulation laboratory model and computer analysis show initial promise for predicted performance. For tabular, flat-lying ore deposits, the Bureau is investigating a version of the Finnish slot-and-fill system. For this total extraction method, a pattern of rectangular panels is laid out. One panel is extracted in a series of parallel slots and is replaced by alternating-row pillars of backfill. After one panel is mined, equipment and operations are transferred to another panel. By transforming this rectangular layout to a curvilinear geometry, one continuous spiral can be mined without re positioning equipment. Instead of parallel slots and pillars aligned in a rectangle, the slots and pillars are arranged in a spiral.

Jan 1, 1992

By José A. Matar Ibañez

Geologic terranes in Argentina include potential mineralized environments from localized younger Precambrian cratonic outcrops through Paleozoic sequences, generally in the northwest or under younger cover, to the Mes[o] zoic-Cenozoic Andean Systems in western and southern Argentina. Argentina is self sufficient or nearly so in many metallic, nonmetallic, and energy commodities, and exploration in each of these categories is ongoing. Present production of precious metals (silver and gold) is important, and many recent discoveries of base metals, precious metals, alloy metals, and other mineral categories have been made. Economic trends, geologic environments, and commodity types important in actual exploration are described, and it is emphasized that extensive areas showing attractive alteration, geochemical, and geological anomalies, especially of porphyry, cordilleran vein, and epithermal characteristics, remain to be fully evaluated.

Jan 1, 1986

By R. G. Lundquist

The idea that fragmentation for mineral processing results from some tradeoff between increased drilling and blasting and increased load on the primary crusher is well known. In a previous paper (Lundquist and Konya, 1963) the authors reported on the results of a laboratory scale study which attempted to quantify this tradeoff in energy terms. If we look only at the production of new surface area, blasting is 1700 times as energy efficient as crushing. On an energy cost basis, crushing is 57 times as expensive per unit surface produced as blasting with dynamite and more than 700 times as expensive as blasting with ANFO. The comminution process at an open pit operation starts with the drilling of blast holes and ends after the material has gone through the fine grind circuit. Operators usually break the process into several separate operations and do their cost analysis based on this approach. Often drilling and blasting is considered as one system and crushing and grinding are considered as one or two separate and independent systems. Operators will independently optimize each system. The cost for the drilling and blasting system is obvious in operations which use contract drillers to do the drilling and either contract the blasting to a distributor or do the blasting themselves. The cost of rock breaking in this manner is readily available since the contract driller will supply a monthly drilling cost to the operation and either the distributor who is contracting the blasting or the distributor who is supplying the powder to the blasting operation will also supply a monthly billing. In either case, the costs can easily be seen on a monthly or per ton basis. They are not difficult to compute even when drilling and blasting are done entirely in-house.

Jan 1, 1985

By F. L. Kadey

A discussion of fillers would not be complete without allotting adequate time to that unique and different mineral material, diatomaceous silica. Historical references to its use challenge the aesthetic aspect of man's curiosity; whereas modern scientific tools have provided a dimension of measurement that has motivated many of its more recent applications. A brief review of what is already known is in order. The diatom is a unicellular, plant-like, microscopic organism, related to the algae1. Its natural function appears to be that of a food for other marine or lacustrine organisms, The diatom's "claim to fame" from an industrial viewpoint is dependent on the fact that it secretes an opaline siliceous skeleton that must survive, chemically and structurally, the geologic processes that caused its formation in the first place; its subsequent demise, burial, consolidation, and alteration; and finally, its ultimate exploitation by man--in somewhat that order. In addition to its siliceous nature, the skeletal structure of the diatom possesses a variety of shapes, patterns, and sizes that have not only been the intrigue of microscopists for decades, but have served to set diatomite apart as an industrial mineral; and have reserved for it applications that cannot be satisfied by any other material. Its chemical inertness, its intricate structure, and its intrinsic hardness-coupled with fineness and friability-- are generally known and have accounted for its application in a wide range of filtration and filler uses. The increasing use of the electron microscope has considerably expanded our knowledge of heretofore unseen secondary and tertiary structure of submicron dimension in the diatom valve. The development of electro-sensing methods of particle size measurement which seem to supersede sedimentation and microscopic techniques has portrayed size distribution in a more realistic light. Interest in the surface chemistry of these silica structures has further strengthened our understanding for certain uses. Thus, new tools and ideas have made possible the introduction of diatomite into such sophisticated technologies as that of chromatographic supports, its improved utility in paint applications for the control of gloss and sheen, and its usefulness in the entirely new concept of "Dry Acid Concentrates." Each of these applications has been discussed elsewhere before people particularly interested in analytical chemistry, in paint, and in liquid handling, respectively, where the diatom has been a means to an end. The emphasis here, before the mining fraternity, however is on diatomite as a raw material with reference to the uses mentioned above. It is therefore toward an awareness and understanding of diatomite properties pertinent to these newer filler applications that this paper is directed.

Jan 1, 1967

By Devraj Sharma

This paper presents technical issues in the design and management of a retorted oil shale disposal site. Major physical and geochemical mechanisms which affect the disposal are: heat transport, moisture migration, chemical species transport, auto-ignition, and mechanical behavior alterations of the retorted oil shale pile. The interaction of these mechanisms and their relative magnitude will affect the environmental behavior of the pile. The paper discusses the coupling between the mechanisms, presents a framework to quantify the processes by laboratory and field measurements, and in addition discusses the use of mathematical models to provide quantitative predictions.

Jan 1, 1981

By Earl H. Miller

The United States Potash Company was the original discoverer and first producer of under-ground mined potash ore in North America and commenced active production of potash in 1931. In July 1956, the company merged with United States Borax & Chemical Corporation and is now a Division of that corporation. The mine is located twenty-two miles east of the city of Carlsbad and the refinery is located sixteen miles south of the mine, The mine was placed where the ore was found and the refinery placed where there was sufficient water for a dissolving and re-crystallization plant. For twenty-three of the last twenty-six years, the potash ore was mined with the room and pillar method, taking approximately sixty percent extraction and leaving forty percent in pillars. These pillars are generally fifty-eight feet by fifty-eight feet square. Three years ago, it was decided that removal of as large an extraction as possible from these pillars should be commenced.

Jan 1, 1958

By Willaim A. Berg

Vegetative stabilization can help meet the esthetic objections and pollution problems posed by mine wastes. However, mine wastes are often unfavorable growth media and special treatments and techniques are needed for plant establishment and continued growth. The establishment of vegetation on mine wastes was the subject of many papers presented at the International Symposium on Ecology and Revegetation of Drastically Disturbed Areas held at Pennsylvania State University on August 3-16, 1969. This paper is a summary of those papers presented at the symposium that dealt with the nutritional and physical aspects of plant establishment on a variety of mine wastes. The synopsis presented is a combination of excerpts from the abstracts, notes on the oral presentations, and rough drafts of some of the papers. The papers will eventually be published in the symposium proceedings.

Jan 1, 1970

By C. B. Daellenbach

The influence of reduction roasting and thermal shock on the grindability of a refractory low-grade Michigan iron ore was examined in bench scale tests. The quantitative effects of the various treatments were evaluated at three sieve levels: 48, 100, and 400 mesh, using ball mill grindability and work index parameters as response indicators. Data from the testing program were analyzed statistically as a means of isolating the effects of cooling rate, roasting temperature, and ore chemical condition. All three variables were found to have an important influence on the grindability of the treated ore; ore chemical condition and roasting temperature had the most pronounced effects.

Jan 1, 1970

By A. M. Raichur

The selective adhesion of hydrophobic Mycobacterium phlei to coal particles is responsible for flocculation of fine coal from associated ash forming minerals. The driving force for the differential adhesion is the hydrophobic interactions between the fatty acid surface of the organism and hydrophobic nature of coal. The effect of Mycobacterium phlei on surface hydrophobicity, surface charge and mechanism of adhesion on coal and associated minerals are controlled by several factors including hydrophobicity and surface and solution chemistry of the system. Adhesion measurements indicate that maximum adhesion occurs below the isoelectric point (IEP) of the coal particles. While massive adhesion of Mycobacterium phlei is observed on coal, however, negligible amount of Mycobacterium phlei attaches to mineral pyrite and quartz.

Jan 1, 1995

By Edward D. Elkins

CalMat Co. is one of the largest producers of construction aggregates in the United States. The CalMat Reliance plant is located in Irwindale, California, and is situated on an alluvial fan formed by the San Gabriel River. The fan deposits are of Quaternary age and were derived from granitic and metamorphic bedrock exposed in the San Gabriel Mountains to the north. The sediments are poorly sorted and range in size from large boulders to clay size particles. The coarse material is hard and durable and consists of quartz diorite, granodiorite, granitic gneiss, schist and minor amounts of volcanic rock. The matrix is comprised of silty sand with varying amounts of clay. Thin silt and clay lenses occur sporadically throughout the deposit. The clay content of the matrix and the degree of weathering of the coarse material increases with depth. Based on seismic data, the alluvial fan varies from 200 to 400 feet thick and overlies crystalline bedrock. The Reliance plant was constructed in 1971 and 1972. It has a nominal capacity of 1200 to 1400 tons per hour, and typically produces more than three million tons of aggregate products per year. Alluvial fan sediments are mined from a gravel pit situated adjacent to the plant. The material is fed through a mobile, 48- by 60-inch, in-pit jaw crusher, then transported by conveyor to the main plant to be processed. The plant is modern and highly efficient. It has a typical wet and dry circuit and is capable of producing a wide range of aggregate products. To extend the life of the plant, a 9,000 foot conveyor system is being constructed to connect it to a granite quarry operated by Azusa Rock Inc. The quarry is located north of Irwindale, and is 50 percent owned by CalMat Co. The conveyor will be used to export crushed rock from the quarry to Reliance. The existing plant will be modified to process the crushed rock.

Jan 1, 1995