Search Documents

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By Peng Zhang

In previous research, the laminated overburden model from the LaModel program was effectively integrated with Analysis of Retreat Mining Pillar Stability (ARMPS) through ARMPS-like input to create a laboratory version of the new ?ARMPS-LAM? program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition, and then automatically develops, grids, runs, and analyzes a full LaModel analysis of the mining geometry to output the section stability factor (SF), all without further user input. The initial ARMPS-LAM results were encouraging with a case history classification accuracy of 55% to 71%; however, a few of the input variables that were nominally included in the SF calculation showed independent significance in the classification accuracy. Therefore, in order to further improve the accuracy of the ARMPS-LAM program, an investigation of the SFs calculated by the new ARMPS-LAM program and the ARMPS program is detailed in this paper. The initial results of a linear correlation between the ARMPS-LAM SF and the ARMPS SF showed a strong correlation (R2 = 0.88), with the ARMPS-LAM SF averaging about 8% higher. The difference in SFs between the programs were further investigated, and, ultimately, the results indicated that the laminated overburden model as implemented in ARMPS-LAM distributes relatively more load on the section pillars for depths less than about 1,000 ft and less load for depths more than 1,000 ft. The results of this research highlight the potential for improving the ARMPS-LAM program in the future by implementing a more accurate loading calculation on the section pillars.

Jan 1, 2014

By Gabriel Walton, Sankhaneel Sinha

"Rib failures are a major hazard in underground mining. When pillars are subjected to loading, extensile cracks are generated parallel to the excavation boundary, which can manifest as rib falls. A common mitigation measure is to install supports, especially bolts, normal to the rib surface. The type and spatial distribution of these supports along the pillar is often based on experience rather than comprehensive analysis. Since conducting field experiments is often impractical and expensive, a convenient alternative is to perform 3D numerical modeling. In this study, FLAC3D has been used to capture the interaction of rib bolts and the failure processes governing the stability of pillars. An associated goal is to determine whether, at all, a continuum software is capable of modeling the effect of supports. The modeling involved two important steps: selection of a proper constitutive model, and, explicit simulation of rock bolts. Based on precursory work in the last decade, an S-shaped strength criterion was chosen that can describe the tensile fracture mechanism of rock at low confinement and shear failure mechanism of rock at high confinement. The built-in pile structural element in FLAC3D is a simplified representation of the complete bolt system. Hence, the different components of a rock bolt (i.e., steel, grout, steel-grout interface, and grout-rock interface) have been explicitly modeled within the rock mass and then tested for its ability to replicate the ground-support interaction behavior. INTRODUCTION Rib failure-related hazards and injuries have plagued the mining industry for decades (Mohamed et al., 2016; Iannacchione and Prosser, 1998). In highly stressed environments, excavation parallel cracks are the primary initiators of skin instability. In absence of any support, this failure can indirectly destabilize the excavation by increasing the exposed span of intersections and roadways. Over the last two decades, there have been numerous injuries (fatal and non-fatal) due to rib failures in underground coal/non-coal mines."

Jan 1, 2017

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By Dongfeng Yun, Zhu Liu, Wendong Cheng, Zhendong Fan, Dongfang Wang, Yuanhao Zhang

"For the purpose of studying the strata behavior due to multislicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams, the shield support pressures of the upper and lower slices of Panel 37220 in Dongxia coal mine were monitored using the KJ513 dynamic monitoring system. The set up rooms adopted the ""horizontal line-arc segmentinclined line"" form and used different types of shield supports. The results showed that the strata pressure of upper slice Panel 37220- 1 changed slightly along the strike direction, while along the dip direction it exhibited strong to weak pressure from bottom to top. The first weighting interval oflower slice Panel 37220-2 was about 60.Sm, and the average periodic weighting interval were about 22.6m. The strata behavior of Panel 37330-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part, followed by the middle and upper parts, arc segment, and finally the lower part. During the periodic weighting, the weighting interval and intensity also exhibited strong space characteristics. The average dynamic load coefficient was 1.48 and the maximum lateral pressure of the side shield was 900Kn1000kN.INTRODUCTIONThe steeply dipping coal seams account for about 20% of proven reserves and 10% of output in China (Wu, et al, 2014). About 50% of coal mines in the western China have steeply dipping seams, and are mainly distributed in Sichuan, Gansu, and Chongqing. When the steeply dipping seam employs longwall mining along the strike direction is employed, the waste rocks fill the gob nonhomogeneously along the dip direction, the deformation and caving of surrounding rocks exhibit obvious asymmetry and spatio-temporal characteristics with particular and complex strata behavior. In recent years, many research on strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams have been performed with significant results (Shi, 1999; Wu, Xie, and Ren, 2010; Wu, Xie, Wang, and Ren, 2010). However, there has been a complete lack of research on monitoring the strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam. Therefore, the strata behavior of multi-slicing panels 37220-1 and 37220-2 was systematically investigated in this research."

Jan 1, 2016

By Y. Luo

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

By Yuanfei Chen, Jianfeng Zha

"China is the largest producer and consumer of coal in the world. The mining-induced surface subsidence has bad influences on the surface and structures above the surface. In order to minimize disasters, removal, reinforcement, or maintenance structures are often adopted. In the application of maintenance methods, it is necessary to carry out dynamic surface subsidence prediction to choose maintenance methods, optimize maintenance time, and evaluate the amounts of work. Time series methods and influence function methods are common for dynamic surface subsidence prediction, but the former is difficult to consider with underground mining conditions, and the latter has low prediction precision. Therefore, this paper develops a dynamic subsidence prediction model aided by field-measured data and realizes the model programming. The model could achieve high-precision prediction of dynamic surface deformation through optimizing the parameters in time by using field-measured data of surface subsidence. The research results of engineering cases show that, with the method of dynamic prediction, the standard error can be controlled in the range of 5%, greatly improving the accuracy of dynamic prediction of mining subsidence, which provides strong technical support for the maintenance and management of structures. INTRODUCTION With the rapid economic development and continued industrialization process, the demand for energy is growing in China. Today, China is one of the largest coal, oil, and gas consumers in the world. Coal consumption accounts for 47.7% of the total consumption in the world (Tian, 2016). In order to meet the demand for coal resources in the process of modernization, more and more coal mines carry out coal mining under villages, buildings, highways, and bodies of water. The mining-induced overlying strata and surface subsidence have bad effects on surface and on various structures (such as buildings, railways, highways, high-tension transmission lines) and could even cause various disasters (Williams et al., 1998; Bell et al., 2000; Doyle et al., 2002). Generally, methods, such as removal, reinforcement, or maintenance are taken to eliminate the adverse impacts (Kraatz, 1984; Bell and Genske, 2001; Wang, 1989). When reinforcement or maintenance is selected to remove bad effects, the proper maintenance methods must be chosen. In addition, maintenance time, as well as an evaluation of time it will take to do the work are necessary to predict the surface subsidence with high precision."

Jan 1, 2017

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By Peter Zhang, Daniel Su, Essie Esterhuizen, Mark Van Dyke, Berk Tulu, Dave Gearhart

"Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site. The roof behavior in the headgate near the face was carefully observed during longwall retreat. Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.INTRODUCTIONLongwall mining is the primary underground coal mining method in the United States and currently accounts for more than 60% of the underground coal production. The longwall headgate, as a passageway for the longwall crew, intake air, material supplies, and coal belt transportation, is critical for both safety and continuous production of the longwall panel. A roof fall in the longwall headgate would not only result in substantial interruption of production but could potentially cause injuries or fatalities. Rehabilitation of failed roof in the headgate would also expose miners to the risk of injuries. Roof falls in the headgate, though infrequent, mostly occur in the belt entry near the face. Considerable research has been conducted to determine the effects of various factors on headgate roof stability, as well as effective measures to support the roof in longwall mines in the Pittsburgh seam (Mark, Mucho, and Dolinar, 1998; Chen et al., 1998; Su and Hasenfus, 1995; Su, Thomas, and Hasenfus, 1999; Su, Morris, and McCaffrey, 2002; Su, Draskovich, and Thomas, 2003; Hasenfus and Su, 2006; Van Dyke et al., 2015). Previous studies have demonstrated that high horizontal stress and transitional roof geology are primary factors that cause headgate roof failure. These studies also showed that panel orientation, retreat direction, pillar sizes, and roof support played an important role in the stability of a headgate.In underground coal mines located in the eastern United States, the magnitude of the maximum horizontal stress is typically three times greater than the vertical stress, and about 40% greater than the minimum horizontal stress. Mark, Mucho, and Dolinar (1998) studied seven cases of headgate failures caused by high horizontal stress in different coal seams in the United States and stated that roof stability is affected, to a large extent, by rock type, entry orientation, and longwall orientation. The effects of horizontal stress can be summarized in these statements: (1) A laminated roof is very vulnerable to high horizontal stress. (2) Entries that are aligned with the maximum horizontal stress will suffer less damage on development than those perpendicular to it. (3) Horizontal stress concentration and relief depends on panel orientation, the direction of retreat, and the sequence of longwall panel extraction."

Jan 1, 2018

By Stephen R. Iverson, Jeffrey C. Johnson, Donovan J. Benton, Michael J. Raffaldi, Lewis A. Martin

"The NIOSH ground control safety research program at Spokane, Washington, is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being used. First, photogrammetric data of laboratory testing is being used to correlate energy input and support deformation. This information can be used to infer remaining support toughness after ground deformation events. This technique is also demonstrated in a field application. Second, field photogrammetric data is compared to crackmeter data from a deep underground mine. Accuracies were found to average 8 mm, but have produced results within 0.2 mm of true displacement, as measured by crackmeters. Application of these techniques consists of monitoring overall fault activity by monitoring multiple points around the crackmeter. A case study is provided in which a crackmeter is clearly shown to have provided insufficient information regarding overall fault ground deformation. Photogrammetry is proving to be a useful ground monitoring tool due to its unobtrusiveness and ease of use.INTRODUCTIONNIOSH Mine Safety ResearchPhotogrammetry systems have been implemented by the National Institute for Occupational Safety and Health (NIOSH) as part of its ground control research to improve mine safety. Conventional monitoring of ground movement has typically focused on movement of a few discrete points that are marked or anchored to instruments. Loss of a designated point or anchor, or the ability to identify a stable point in an unstable area, have often frustrated monitoring efforts. NIOSH researchers are using photogrammetry to conduct full-field measurements of rock surfaces underground. Periodic measurements of the entire surface of a ramp allow patterns of displacement to be observed. Full-field measurements provide much more insight into ground behavior than point measurements.BackgroundPrevious work by Benton, et al. (2014) discussed laboratory calibration and verification testing of two photogrammetry systems being used by NIOSH researchers. Both systems utilize stereoscopic image pairing techniques for photogrammetric reconstruction. This paper discusses how a laboratory system was used to conduct volumetric analyses of testing of shotcrete panels with varying types of reinforcement. The laboratory system was found to be accurate to within 2 mm. Additionally, a field photogrammetry system was found to produce linear measurements within 1 mm of known lengths in laboratory conditions. This system is currently being used at a deep underground mine to observe ground support conditions and deformations that have occurred. This paper discusses comparison of preliminary volumetric measurements of rib deformation to laboratory tests, as well as comparison of the field system against a crackmeter installed across a fault surface where it intersects the ramp."

Jan 1, 2015

By Jun Lu

This paper presents the evaluation, enhancement and comparison of two hydraulic fracturing techniques which were employed to mitigate the impact of a massive sandstone channel on two successive longwall faces. The hydraulic fracturing technique and Longwall Visual Analysis (LVA) software were initially employed to mitigate the impact of thick, massive sandstoneroof during mining of longwall Panel 21. Improved longwall face conditions and productivity were observed as Panel 21 mined through the sandstone channel. However, moderate sandstone fractures and falls at the face were still present in areas where hydraulic fracture influence was not present. Such adverse conditions caused two to three weeks of production delays due to large face cavities, jammed face conveyor and subsequent face gluing. Based on the mining experience in Panel 21, and site-specific roof geology in Panel 22, a modified and more effective hydraulic fracturing program was employed. Fewer well-placed holes were drilled, and larger volume of water was pumped into each hole in order to propagate the individual horizontal pancake fractures over a larger area, thereby enhancing caving and relieving face pressure caused by overhang of the massive sandstone. Longwall Visual Analysis (LVA) software was also employed at Panel 22 to predict the cavity risk index and guide the longwall face crew in double-pulling shields behind the shearer drum. This helped to reduce the tip-to-face distance at the critical spots along the longwall face, which helped mitigate the formation of the roof cavities and failure of massive sandstone onto the face conveyor. Underground observations, face advance rate and face rock delay analysis confirmed that longwall face conditions and advance rate in Panel 22were significantly improved compared to those of Panel 21. Consequently, safety and productivity were improved.

Jan 1, 2014

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Filippo Vallianatos, Michael Verigakis, Vasili Saltas, Kosta Kaklis, Stelio Mavrigiannakis, Zach Agioutantis

"Development of failure in brittle materials is associated with microcracks, which release energy in the form of elastic waves called acoustic emissions. This paper presents results from acoustic emission measurements obtained during three-point bending tests on Nestos marble under laboratory conditions. Acoustic emission activity was monitored using piezoelectric acoustic emission sensors, and the potential for accurate prediction of rock damage based on acoustic emission data was investigated. Damage localization determined based on acoustic emissions evident in the critically stressed region in the form of scattered events or stresses below and close to the strength of the material.IntroductionNon-destructive testing (NDT) has gained popularity in recent years due to commonly available sensors, devices and software tools. Although the majority of such testing still occurs under laboratory conditions, the ultimate goal is a direct field application, especially in the case of underground mining. NDT, if properly applied, may be used to directly provide material property values and characteristics that can be used to determine rock mass or soil mass behavior, with a direct impact to mine design (Iannacchione et al., 2003).AE is generally defined as the high-frequency transient elastic waves originating from the sudden release of energy at localized points within a loaded material (Nomikos et al., 2010). The field of Acoustic Emissions (AE) due to compressive, tensile or other types of loads is a promising research area due to its wide application. The accurate identification of failure precursors stemming from AE is still an open research topic (Lei et al., 2004).Rock is a typically inhomogeneous and anisotropic material that contains several natural defects with various scales such as grain boundaries, microcracks, pores and joint inclusions (Jing, 2003; Read, 2004). Damage induced by microcracks is an essential mechanism in many brittle rocks subjected to stresses. An applied stress induces microcrack growth and damage is distributed uniformly throughout the sample. Finally, the microcracks coalesce and the damage is localized to a shear band, leading to strain softening and macro-scoping failure (Dragon et al, 2000)."

Jan 1, 2015

By Shengliyang Yang, Jinghu Yang, Jiachen Wang, Xiaomeng Li

"Safe and efficient mining of extremely inclined thick coal seams less than 20m thick is one of the new challenges in China coal industry. In recent years, the extremely inclined thick coal seams have been encountered in some old mines and western China, and currently the top coal caving longwall mining method has been successfully applied to this kind of coal seams. Accordingly, this paper studies the roof movement and its impact on shield supports of top-coal caving longwall mining in extremely inclined thick coal seams. The structure of main roof before failure was simulated by the fix-ended beam, and provided the solutions for determination of maximum compressive stress of the bottom beam end and maximum tensile stress of the top beam end. The failure mode on the upper end of working face is mainly a combination of compression and shearing, while that for the bottom end is tension and shearing. Roof fracture begins at the upper end of working and propagates downward. The shape of collapsed roof strata can be described as parabolic and divided into three segments from top to bottom, including no filling, uneven filling and densely filling segments. The roof loading conditions of no filling segment is more likely to have dynamic burst impacts.INTRODUCTIONExtremely inclined thick coal seam refers to that the dip angle of coal seam is greater than 45° and the thickness is greater than 3.5m (Wang and Zhang, 2015a; Wang and Zhang, 2015b; Wang, 2005; Xie, Gao, and Shangguan, 2005; Wu, et al., 2014; Deng and Wang, 2014; He, et al., 2015). This type of coal seams can be divided into three categories: 1. The extremely inclined thick coal seam, of which the thickness is less than 5m and the dip angle is less than 60°, is usually mined by fully-mechanized longwall mining method. 2. The extremely inclined thick coal seam, of which the thickness is 5 m-20m, is usually mined by top coal caving longwall method. And 3. When the thickness of extremely inclined thick coal seam is greater than 20m, it is mined by the horizontal section top coal caving longwall method. For example, the average angle ofWudong coal mine in Xinjiang province is 45°, and the thickness is 27m. Wudong coal mine is applying the horizontal section top coal caving longwall mining, producing 3 million tons annually per working face (Figure 1)."

Jan 1, 2016

By Guy Reed, Russell Frith

"The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database.This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength “index.” These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of super-critical overburden behaviour as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases.A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.INTRODUCTIONThe inspiration for this paper is founded in three statements from two eminent persons in the field of coal pillar strength research, Jim Galvin and Essie Esterhuizen, as follows:Both Salamon and Munro and [the University of New South Wales] based the derivation of their pillar strength formulae on a criteria that the diameter of a panel of pillars, W, had to at least equal the depth of mining, H. This was thought to result in full tributary loading. It is now known that there are some mining environments included in both the South African and Australian databases in which mining span must exceed depth by a considerable margin in order to achieve full deadweight loading. Hence, it is logical to conclude that these data points may have contributed to pillar strength being overestimated by Salamon and Munro and UNSW (underline added by authors). Normally, this should be of no consequence because it is reflected in the probability of design success associated with any given safety factor (Galvin, 2006)."

Jan 1, 2018

By Yunqing Zhang

Weak shales refer to those with lower strength, thinly- laminated structure, sensitivity to moisture and weathering as well as significant time dependent behavior. It has been said that many future coal reserves with good quality have weak immediate roofs. Therefore their geo-mechanical properties and behavior must be known before an appropriate support plan can be designed. In this study, four types of shales collected from underground coal mines were tested in the laboratory. Their modes of failures in underground were observed and correlated with their lab behavior. The failure mechanisms of thinly-laminated weak shales were analyzed by the means of numerical modeling.

Jan 1, 2004

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By John Stankus

Seam interaction in multiple seam mining has significant effect on entry stability. The remaining pillar in an old working usually creates a high stress concentration zone while the gob creates a stress release zone. A good panel layout should take advantage of the stress release effect created by old workings. This paper presents two case studies of multiple seam mining. The Jennmar Finite Element Analysis System (JFEA) is utilized to analyze the seam interaction effect and identify the mess concentration and relief zones Panel layouts are designed bad on the results of the finite element analysis Appropriate roof support system are also designed for different seam interaction areas.

Jan 1, 1999