Search Documents

By Hideki Shimada

A low cost methodology that allows the determination of in- situ stress using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the AE and DRA methods to those estimated by conventional ANZI (Australia and New Zealand Inflatable) cell measurements. The studies have been focused on fill stress tensor determination from a single oriented cored rock. In all cases the rock core specimens recollected the in-situ stress reasonably well compared with the standard overcoring method.

Jan 1, 2001

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By Tom Vandergritft

With advances in system design driving higher productivity, safety, and coal recovery, highwall mining is becoming an attractive option for extending reserve life at surface mines. Typically, highwall mining is performed by contract, with the system owner charging the mining company on a per ton basis, plus a mobilization fee. For this arrangement to benefit both parties, geotechnical planning is required to minimize risk to highwall mining personnel and equipment, while maximizing coal recovery. This paper discusses how highwall mining has been successfully implemented at a large surface coal mine in Colorado, including design procedures, operational factors, and productivity. The operation includes an area where four seams are mined in succession from the lowermost upward, requiring careful attention to seam interaction issues.

Jan 1, 2005

By Michael Trevits

The NIOSH Lake Lynn Laboratory (LLL) is a unique research facility, located about 50 miles southeast of Pittsburgh, Pennsylvania, that is designed to provide a full-scale mining environment for testing and evaluation of mine health and safety technologies. The LLL occupies more than 400 acres and is composed of surface test and training areas and an underground mine. The Lake Lynn Experimental Mine (LLEM) was built at an abandoned commercial limestone quarry where surface mining ceased in the late 1960's. Later, new underground development was constructed to simulate modern-day coal mining scenarios; including room-and-pillar and longwall mining layouts. In January 1994, a sinkhole opened southeast of the No. 4 Portal of the LLEM and since then, the area of the underground failure and surface deformation has continued to expand and now includes several interconnected sinkholes. A concern developed that the overburden instability could expand and affect the structural integrity of the nearby highwall and the No. 4 Portal. It was unsafe to conduct a detailed underground survey of the mine in this area because the mine roof conditions near the No. 4 Portal had deteriorated significantly. It was decided to investigate the overburden conditions near the No. 4 Portal using ground penetrating radar (GPR). A GPR survey grid was located along an access road that passes over the top of the portal. To delineate the mine conditions near the portal, antennas whose frequency spectra produced pulses centered near 100- and 200-MHz were used. The results of the GPR survey suggests that the overburden rock units appear to be laterally consistent to a depth of about 15-ft. Below that point, the overburden appears to be significantly disturbed and it was hypothesized that this area contains a large roof fall. A follow-up ground truth survey of the mine roof conditions was conducted from the mouth of the portal. It is concluded that the observations and measurements made from the radar records appear to be correct as a large roof fall was observed and measured from the mine portal area.

Jan 1, 2005

By R. Karl Zipf

Highwall mining is an important coal mining method. Upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mine Safety and Health Administration (MSHA) accident data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwail miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Trapped highwall miners present a safety hazard to workers during their recovery. Best practices to avoid trapped highwall miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system, Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

Jan 1, 2004

By P. E. Christensen

Due to ever-increasing stripping ratios associated with the No. 8 Seam at the San Juan Mine surface operation, BHP Minerals decided to implement longwall mining for the extraction of the substantial future reserve base. In preparation for longwall developments, BHP opted to first develop a small-scale pilot operation within the No.8 Seam on an adjacent lease to address geotechnical/geological concerns related to ground control, subsidence, caving, panel and entry design, and operational issues related to entry development and proper face equipment selection. Room-and-pillar mining methods are currently being utilized to develop a full extraction panel for a wide range of geological, geotechnical, and geomechanical evaluations aimed at characterizing and assessing the mineability of the No.8 Seam. Variable roof and floor conditions, coupled with a multi-bench coal seam, require that a number of mining horizons, opening geometries, and roof and rib support fixtures be evaluated relative to expediting gate and panel developments. Issues related to development of timely caves in areas subject to overlying sand channel deposits will also be addressed through underground in-seam stress and deformation measurements, and interburden and surface subsidence monitoring. This information will ultimately be used to evaluate face support and gate and panel pillar/entry development requirements. The current depositional model for the property, developed from an aggressive drilling, highwall mapping, and lineament evaluation program, will also be refined during the Pilot Mine study through extensive in-trine mapping, additional roof and floor drilling and physical property testing, and determination of the in situ principal horizontal stress field.

Jan 1, 1998

By William Bookshar

The development of increasingly more sophisticated and powerful retreat longwall equipment has led to ever wider and longer panels. To maximize gateroad development efficiency, provide for effective face recovery, andlor reduce ventilation pressures, entries are cut across longwall panels in advance of longwall retreat mining. These entries must be supported to prevent falls of immediate roof in advance of the face. Recently, cut through entries and predriven recovery room entries have been supported with various combinations of roof bolts and passive support. The cost and relative success of these support systems has varied considerably. Eighty-Four Mining Company, Fosroc, and Sub-Technical have developed and implemented an efficient, yielding, multiple component, cement crib to support longwall panel cut through entries and pre-driven recovery rooms. The cutable crib consists of an inexpensive flyash cement pillar poured in a bag, within a temporary metal form. The form is moved to a subsequent cutable crib location after the initial hardening of the flyash pillar. The remaining entry height between the mine roof and the top of the flyash cement pillar is filled with a specially designed bag filled with Fosroc's Tekset cement formulation. The diameter of the pillar and thickness of the Tekset bag are designed to accommodate the anticipated front abutment loading and entry convergence.

Jan 1, 1998

By M. Karmis

mining factors and representative ground movement parameters. Based on this analysis, the previously developed prediction methods were modified and tested for their applicability in the Appalachian coalfield. Finally, in order to facilitate the implementation of the prediction methods, as well as the data processing of the monitoring program, a number of computer software were developed and will be discussed in the paper. Surface deformations above underground mines and their prediction and control have been the topics of an extensive research effort by Virginia Polytechnic Institute and State University over the past few years. During the initial stages of this research, a number of case studies were collected from the literature, the mining industry and various government and state agencies and, based on the analysis of this information, appropriate prediction methods were proposed (Goodman, 1980; Webb, 1982; Hasenfus, 1984; Karmis et al., 1984). Although the prediction methods were based on sound concepts, it became evident that their accuracy and implementation were a reflection of the size and quality of the collected case studies. In this respect, the data bank was rather insufficient and posed certain questions regarding the development of subsidence information due to inappropriate length and spacing of monuments used in subsidence surveys, density and accuracy of such surveys, lack of monitoring horizontal movements, etc. In an effort to alleviate these problems, a comprehensive monitoring program was initiated in the coal mines of southwest Virginia, which included: - Two longwall and five room and pillar mines. - In total, seven longwall and sixteen room and pillar panels. - Monitoring lines in excess of 35,000 feet. - Vertical as well as horizontal measurements. A high accuracy digital computer tacheometer was used in all surveys and the type and spacing of all monuments were in accordance with well accepted guidelines. The data from this monitoring program completed the initially collected data bank and, thus, enabled a much needed statistical analysis between

Jan 1, 1987

By Stephen Tadolini

Reduction in the time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. While this concept is not without controversy and risk, the rewards can result in substantial reductions in longwall face move/set-up times and provide safer working conditions. Both of these factors can reduce mining costs and enhance profitability in a competitive market. This project was even more complex because the longwall system operates under a weak roof condition. To examine the feasibility of this concept, a 16-ft wide by 170-ft long experimental pre-driven recovery room was designed using analytical, empirical and 3-dimensional finite element modeling techniques. Based on the projected loading conditions, immediate and main roof geological and strength characteristics, a variety of roof bolt types were selected and installed in the recovery room and adjacent chutes. To supplement the intrinsic supports, high-capacity roof-to¬floor cuttable cribs were strategically placed to reduce the potential of a weighting failure before the longwall shields safely entered the room. To evaluate the behavior and final support performance, the recovery room and chutes were instrumented to monitor the physical response during various loading phases. Additionally, the cuttable cribs were instrumented to evaluate the loading and stiffness characteristics during the extraction process. This paper describes the successful design process, support methodology, monitoring results, final observations and recommendations.

Jan 1, 2002

By J. S. Oram

Maltby Colliery, operated by RJB Mining (UK) Ltd is successfully mining the Parkgate seam in Yorkshire at a depth of 1000m using longwall retreat. Extraction in the Parkgate seam is influenced by interaction from previous workings in the Swallow Wood Seam 160m above. The paper describes in-situ stress measurements and simple gate road convergence measurements carried out to assess the extent of the interactive influence. The stress measurements, obtained using the stress relief overcore technique, were carried out from a maingate development roadway in an area where the stress redistribution under an overlying pillar and adjacent panel goat could be measured. The measured vertical stress distribution confirmed a significant interactive influence with high imposed vertical stresses under the overlying panel edges. Simple roadway convergence monitoring stations established in the gateroads of a retreating panel and in the development gateroads of the adjacent panel, confirmed higher rates of roadway deformation relating to overlying panel edges and pillars, particularly in the areas where a vertical stress window developed during panel retreat. In addition to highlighting a close relationship between closure rate and the measured vertical stresses, the convergence monitoring proved valuable in establishing characteristic deformation behaviour under specific interactive influences and also in defining the optimum location, extent and time of installation u£ additional roadway support and reinforcement. The information from the measurement programme has enabled the Mine Management to gain a better understanding of the interactive influences on roadway behaviour and was instrumental in designing the layout of panels in an area of the North East district of the mine where previous experience had indicated the combined influence of high interactive stresses and weak roof lithology resulted in difficult strata conditions both at development and on panel retreat. The planned location of panels and gateroads took into account both mining operational considerations and the need to avoid potentially high risk interaction zones as highlighted from analysis of the monitoring results. To obtain additional data on parameters influencing roadway deformation, extended roadway convergence monitoring has been established.

Jan 1, 1997

By Jinsheng Chen

For underground openings, many factors can cause roof failure and thus roof falls. The most common factors related to Mother Nature are weak roof lithology, geological structures, and an abnormal in-situ stress field. Theoretically, any underground opening can be successfully supported under any geological and mining conditions if the opening width is limited and the roof supporting system is well designed. However, roof control cost must be taken into account. In practice, to minimize the roof control cost, different roof control plans have to be considered to take care of the uncertainty or variation in geological and mining conditions. For most underground mines, it is unsafe or economically unrealistic to use one fixed roof control plan for the entire mine. Therefore, local, abnormal geological and mining conditions must be identified and a site- or area-specific roof control plan must be employed. This study tries to identify the major factors that have significant impact on entry roof stability by analyzing the historical roof fall data at Rofomex mine. Finally, the appropriate roof control plans or roof bolting systems for different geological and mining conditions are recommended.

Jan 1, 2011

By David Newman

Coal refuse impoundments and underground mines are frequently sited in close vertical and horizontal proximity in the valleys of the Southern Appalachian coalfield. The steep V-shaped valleys provide the volume necessary for slurry storage against a coarse refuse embankment that is constructed across the valley mouth. The presence of coal outcrops on the valley walls provides economic access to mineable coal seams that may be located under several thousand feet of overburden beneath the adjacent ridges. In some instances where the underground mine precedes the slurry impoundment, the type of mining (partial or complete extraction) and pillar centers were selected without consideration for the potential future use of the valley as an impounding structure. The high standard established for the design and stability analysis of the coarse refuse embankments is clearly illustrated by the absence of an embankment failure in the thirty-one years since Buffalo Creek. However, the recent Martin County slurry spill focused attention on a thorough geotechnical analysis to prevent a connection between the flowable slurry and the mine void. The overburden, roof, pillar, floor, and outcrop barrier stability are examined to quantify the break through potential. The strength and physical properties of the consolidated fine refuse are also important since this material is often the most well-defined and quantifiable barrier separating the slurry and mine void. Because each site is unique, the appropriate analysis ranges from the calculation of roof, pillar, and floor safety factors to detailed numerical modeling of the mine workings and the determination of ground deformation and strains resulting from mine subsidence. The method of refuse disposal may be altered to slurry cells where the accuracy of the mine maps, extent of mining, type of mining (development or retreat) cannot be reliably verified or the break through analysis does not produce an acceptable level of risk. Case histories from the Southern Appalachian coalfield are used to illustrate the application of methodologies to quantify the break through potential of coal refuse impoundments.

Jan 1, 2003

By Thomas M. Baraak

This paper evaluates factors which influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: 1) longwall panel, 2) powered roof supports, and 3) gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from subsidence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data suggest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 1990

By Lisa Burke

In underground coal mines, concrete block stoppings are widely used to control mine ventilation. Although stoppings are not intended as roof support, they are subjected to roof to floor convergence, and may fail as a result of this loading. Premature failure of stoppings can significantly affect mine ventilation, limiting the amount of fresh air reaching the working faces and increasing the risk for methane explosions. Softening materials are often used in stoppings to reduce the damaging effects of roof to floor convergence. However, to date, research has not focused on the behavior of stopping construction materials subjected to roof or floor loading, leaving the design process to trial and error. A combination of numerical simulations and large scale physical tests were employed to develop a scientific understanding of stopping performance. The first series of physical models were constructed using standard CMU (concrete masonry unit) blocks and tested in a load frame. The behavior of these walls was simulated with a distinct element model. A key finding was that very small variations in block size and irregularities in block shape significantly affect wall performance. These variations, which are inherent to the type of blocks typically used underground, create stress concentrations that initiate the failure of stopping walls. A second series of models employed concrete stoppings that incorporated woos planks, a shredded wood material, and foam planks like those commonly used underground. Numerical models were again able to match the physical test data. Analysis of the softening layers used in stopping construction indicated that the strength and stiffness of the material relative to that of the wall is crucial in determining the amount of roof to floor convergence the wall can withstand prior to failure. The product of this study is a numerical model that can be used to evaluate the performance of stopping materials and different wall geometries in a controlled environment. Testing was done in a laboratory setting with walls constructed on flat, parallel surfaces and subjected to uniform loading at a constant rate. Parametric studies with the model indicate that in this ideal environment it is possible to control the amount of vertical displacement the stopping can withstand by adjusting the number of softening layers built into the wall and the thickness of the layers. Additionally, under these conditions, the position of softening layers within the wall appears to have little effect on the amount of displacement walls can withstand prior to failure.

Jan 1, 2004

By John Feddock

This study deals with underground mines and ground control and the prediction of seats strength characteristics based upon ultrasonic logging. Exploration drill holes, both rotary and core holes are used for proving coal reserves and determining mining parameters. Drill hole cores can be subjected to geologic study and geotechnical evaluation. In addition, the use of geophysical logging techniques is well established in determining certain strata characteristics and ground parameters. Since the characterization of the rock mass in mines remains insufficient in most cases, the idea of possibly characterizing the strength parameters without expensive core retrieval and laboratory testing is very attractive. The elastic properties of the rock can be deduced from measurement of the sonic velocity if the density is known. Through the use of in-hole geophysical density logging combined with an ultrasonic logging tool, the estimation of strata properties is possible. An investigation was conducted at two Indiana underground coal mines using geologic logging, geophysical logging, ultrasonic logging and laboratory strength testing to establish the strength properties of the roof rock. A specialized ultrasonic logging tool with one transmitter and two receivers enables nearly continuous readings along the length of the hole. The results of correlating portions of the data are presented. It is anticipated that the ultrasonic logging will be a supplemental tool for extending laterally the strata characteristics obtained from the existing program to surrounding areas. This may be obtained from the relatively inexpensive logging data obtained by ultrasonic logging.

Jan 1, 2003

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

By Shu Cheng

Abstract: Based on the consolidation theory of soil dewatering and land subsidence prediction methods in soil mechanics, preliminary analysis of surface subsidence and movement due to groundwater withdrawal was performed using the stochastic theory and the principles of effective stress and the method for subsidence prediction was derived, Surface subsidence due to coal mining was then superimposed to obtain the total subsidence. Keywords: land subsidence, rock and soil consolidation, stochastic theory, effective stress

Jan 1, 2002

By D. W. H. Su

A two-year study was conducted by CONSOL in a northern West Virginia coal mine to evaluate pillar design and support requirements to improve roof control in right-hand longwall headgates subject to high in situ horizontal stresses. Horizontal stress measurements conducted within undisturbed areas of the subject mine revealed a pre-existing regional horizontal stress field with a significant difference in magnitude between the east-west maximum and the north-south minimum stresses. Three¬dimensional stress cells installed to monitor horizontal stress concentration in the headgate roof during mining revealed that a narrow (60-foot center) headgate pillar reduces the east-west horizontal stress concentration in the roof ahead of the face such that the headgate is more stable and requires less support. This 60 foot x 140-foot pillar design, which has been employed in subsequent panels, still provides adequate stress attenuation to protect future tailgates under a maximum cover depth of 1000 feet. Roof geology derived from underground roof reconnaissance and underground bolt load and roof displacement measurements confirmed the effectiveness of 12-foot long cable bolts for controlling the headgate roof subject to high horizontal stresses. With the new headgate pillar design and the supplemental cable bolts, headgate roof conditions in the subsequent panels improved significantly, longwall production delay due to adverse headgate roof condition was totally eliminated, and record coal production was achieved by the subject mine in the subsequent years.

Jan 1, 2003

By P. Palmer

Using 3D numerical modeling as a tool to predict rock behavior during mining extraction is still an uncommon practice at many underground operations. This paper will discuss how 3D numerical models were used to identify potential underground instability problems in the later stages of mining. Detailed modeling was then used to make modifications to the mine design in order to minimize the impact of the potential instability problems. This paper will also discusses how the back analysis of a previous underground collapse event at the same mine in a room and pillar area was used to identify the instability problems for a new orebody being developed deeper in the mine. A 3D numerical model was first created in the MAP3D software to determine the conditions of the pillars and the magnitude of the vertical displacement above the mining zone prior to the underground collapse. The results from the ground collapse model were then used as a threshold limit for predicting potential instabilities and developing a model for the new mining zone. sing the results from this analysis, mine management has been able to implement a much higher percentage recovery of the reserve in a new, high-grade area of the orebody while minimizing potential instabilities in the future.

Jan 1, 2005

By Xu Linsheng

Datong coal Mine suffers from delays and sudden caving of its massive competent conglomerate roof. Detailed geological studies of the nature of pebbles and matrix of the conglomerate and its sparse bedding, joint and fracture structure, gave rise to investigation of water injection to destroy its strength and to control caving. Comparative investigations, including porisity, permeability, compressive strengths and water injection of conglomerate and sandstone led to empirical expressions relating various properties and to guidance for effective injection and caving practice. This new safe roof control practice should be even more improved with further research, including modelling.

Jan 1, 1992