Search Documents

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By M. I. Novgorodova

Most of the gold in the earth's crust occurs as finely-dispersed gold and accounts for much of the gold lost in extraction processes and during exploration for gold. The Compositions, sizes, and morphology of fine gold particles (0.01 to 10 ~m in diameter) were studied with high resolution electron microscopy coupled with electron microprobe and microdiffraction devices, using colloidal carbon replicas. Correlations were made between fine gold, mineral associations and ore genesis. The results provide qualitative information on the proportions of finely dispersed, invisible and visible gold distribution in ores. Such knowledge is fundamental when planning an optimum technological recovery process.

Jan 1, 1991

By Yun Li

An innovative lead recycling process from scrap lead-acid battery paste is presented. The novelty in the process is avoiding SO2 generation and emission by using reductive sulfur-fixing technique. Iron-bearing secondary wastes produced from metallurgical industry were utilized as sulfur-fixing agent to capture sulfur in the form of FeS (s) instead of generation of SO2 (g). Na2CO3 molten salt was added to the smelting system to speed the reactions and improve valuable metals’ recovery and sulfur-fixation efficiency. Furthermore, this process can simultaneously co-treat various lead and iron-bearing wastes. At the same time, some precious metals, such as Au and Ag, contained in iron-bearing wastes can be recovered. The feasibility and reliability of this process was investigated thermodynamically and experimentally with the help of HSC 9.0 database and XRD and SEM-EDS analysis. A possible reaction mechanism and path in PbSO4–Fe2O3–Na2CO3–C smelting system was also clarified.

By S. Z. El-Tawil, K. A. El-Barawy, M. B. Morsi, M. M. Nasr, Z. I. Zaki

"Tue sulphatization of zinc concentrate produced from heated zinc concentrate of Um Ghieg area, eastern desert by ammonium sulphate as sulphatizing agent is carried out at different conditions to achieve the appreciable formation of soluble sulphates. The maximum zinc recovery as soluble sulphate equfils to 95% upon using 1.5 stoichiometry ammonium sulphate at 600 °C for one hour. Tue obtained leached zinc sulphate solution is subjected· to purification process to prepare high pure zinc metal and zmc compounds such as pure zinc sulphate, zinc caibonate and zinc oxide. The products obtained are analyzed chemically and identified by X-ray analysisTue mechanism and kinetics of the sulphatization process of zinc concentrate are considered where the activation energy is calculated and equals to 33.3 K.J.mol""1 A process flowsheet for the overall sulphatization process of zinc concentrate by ammonium sulphate is proposed.IntroductionConsiderable reserves of zinc ores are present in Um Ghieg area eastern desert, Egypt. The possibility of extraction zinc from these ores and preparing its valuable compounds by choosing a more feasible technology become of vital importance. An attention is focused on the sulphatizing roasting processes (1-9) to achieve the appreciable formation of soluble sulphates. Previous publications are reported in our division by El. Tawil and others (10-16) using ammonium sulphate as sulphatizing agent for the successful treatment of nonferrous bearing materials.Therefore, the present work aims to study the different factors affecting the sulphatizing roasting process of local zinc coocentrate by anunonium sulphate to extract completely zinc and preparing its main compounds. Tue mechanism and kinetics of the different chemical reactloos that 1ake place in the process are considered."

Jan 1, 2000

By J. Leon-Torres, D. M. Stefanescu, P. A. Curreri, S. Sen

"Experiments were performed under terrestrial gravity (lg) and during parabolic flights (10·2 g) to study the solidification and macrosegregation patterns of Al-Cu alloys. Alloys having 2% and 5% Cu were solidified against a chill at two different cooling rates. Microscopic and Electron Microprobe characterization was used to produce rnicrostructural and macrosegregation maps.In all cases positive segregation occurred next to the chill because of the shrinkage flow, as expected. This positive segregation was higher in the low-g samples, apparently because of the higher heat transfer coefficient.A 2-D computational model was used to explain the experimental results. The continuum formulation was employed to describe the macroscopic transports of mass, energy, and momentum, associated with the solidification phenomena, for a two-phase system. The model considers that liquid flow is driven by thermal and solutal buoyancy, and by solidification shrinkage. The solidification event was divided into two stages. In the first one, the liquid containing freely moving equiaxed grains was described through the relative viscosity concept. In the second stage, when a fixed dendritic network was formed after dendritic coherency, the mushy zone was treated as a porous medium.The macrosegregation maps and the cooling curves obtained during experiments were used for validation of the solidification and segregation model. The model can explain the solidification and macrosegregation patterns and the differences between low- and high-gravity results."

Jan 1, 1999

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By Hani Henein

"Heat transfer between droplets/particles and a gas phase plays an important role in the transport of numerous materials processing operations. These include rapid solidification operations such as gas atomization and spray forming, as well as chemical systems such flash furnaces. Chemical reaction rates and solidification are dependent on the rate of gas-particle or gasdroplet heat transport. Using a heat transport model validated using single fluid atomization of molten droplets; the effect of process variables on heat losses from droplets was examined. In this work, the effect of type of gas, droplet size, gas temperature, gas-droplet relative velocity on the heat transport from AA606 l droplets was examined. The most critical of these process variables to heat transfer is identified and will be presented.IntroductionIn materials processing, droplets are often encountered and used in processing a wide range of liquids and slurries. The small size of the droplet enables high reaction rates or high solidification rates in many systems. In order to capitalize on these high rates of transport processes, sprays are· also developed to maximize throughput. The design of these sprays, however, does not account for the transport steps and rate limiting mechanisms at the droplet surface. Rather, spray design focuses on maximizing the break-up of a stream or slurry into small size droplets or controlling the spread of the spray. Spray systems in industrial use typically generate droplets of wide size distribution leading to a wide range of reaction times for each of the droplets. Often the generation of a spray involves a number of coupled phenomena such as stream break-up, droplet-gas transport, droplet size distribution and spray geometry. Using gas generated sprays, it is not possible to identify how individual process variables contribute and control each of these coupled phenomena. While many mathematical models have been developed of sprays and they attempt to simulate coupled droplet transport, they do not provide insight into the contributions of different mechanisms in heat transfer. This is primarily because the basic fundamental heat transport between droplet and gas cannot be isolated from other gas spray phenomena experimentally such as two-way thermal coupling [l]. Thus, experimental validation of heart transfer of large and complex industrial spray models is not carried out. Hence, the validity of spray models remains in question and the approach required to optimize spray processes cannot be clearly identified"

Jan 1, 2004

By R. Schaller, Ch. Karcher, A. Thess

"Electron beam evaporation of liquid metals is an innovative technology increasingly used in industry to produce very thin coatings of high purity. In this process the surface of a metal ingot, placed in a water-cooled copper crucible, is heated by bombarding it with a high-energy electron beam gun. The material melts, forming a free surface and eventually starting to evaporate. The rising vapor cloud condensates as a thin film on a moving substrate. The strong energy input at the free surface gives rise to vigorous thermos capillary and buoyancy driven convective motion within the melt, leading to unwelcome heat losses. This paper aims to show how these losses can be reduced by optimizing the geometry of the crucible and by using external magnetic fields. We present both experimental and numerical results.IntroductionElectron beam evaporation of liquid metals [l] is an innovative PVD-technology which is excellently suited for the industrial production of high-quality coatings. In this vacuum process a high-energy electron beam heats up the surface of a metal ingot. The ingot melts and forms a free surface. A schematic view of the arrangement is shown in Figure 1. When the temperature of the free surface exceeds the actual (pressure-dependent) saturation temperature of the ambient gas, the liquid starts to vaporize. The rising vapor cloud finally condensates on a moving substrate located at some distance above. To guarantee a superior quality of the coating the melt is typically confined in a water-cooled copper crucible. The intensive cooling is necessary to avoid chemical reactions between the melt and the crucible walls, that is, crucible materials and their reaction products are practically excluded from evaporation."

Jan 1, 1999

By G. L. Watt

Fine sized titanium diboride (TiB2) powders have been synthesized in a thermal plasma reactor. Precursor for the synthesis were rutile, boron oxide, and methane. The effect of plasma gas type, precursor ratio, and input power on the synthesis was studied. The produced powders were characterized by X-ray diffraction and chemical analysis. The purified powders were CIP'd, HIP'd, sintered and characterized for porosity, hardness, and microstructure and the results compared with a commercially available TiB2 powder sample.

Jan 1, 1995

By Y. Houbaert, L. Kestens, R. Decocker

"A magneto-elastic model is presented to calculate the orientation dependence of the magnetostrictive strain, observed at saturated magnetisation in ferromagnetic materials with a cubic crystal structure and an arbitrary crystallographic texture. The formula of Becker and Doring is used to express the anisotropy of magnetostriction for a single crystal. In order to simulate the macroscopic average magnetostriction of a polycrystalline aggregate (with an arbitrary texture) the Reuss assumption of the elasticity theory was applied. According to this assumption the various orientations of the polycrystal can defonn without constraints, producing local strain incompatibilities in the microstructure but observing total stress equilibrium. The macroscopic strain is calculated as the weighted average of the individual strains of all orientations composing the polycrystal. The weight factors are determined by the volume fractions of the corresponding orientations of the given texture, which can be measured by standard X-ray diffraction techniques. The model is applied to simulate the variation of magnetostriction (at saturation) with respect to the rolling direction for a standard grade of Goss-oriented electrical steel. A brief comparison with experimental data allows validating the basic model assumptions. IntroductionBecause of tougher environmental constraints, the noise reduction in transformer cores has become increasingly important. It is generally accepted that the main source of noise is magnetostriction, which is known to be caused during the magnetisation process by the movement of 90° magnetic domain walls and the rotation of the magnetisation vector out of the easy directions. Therefore, it is obvious that when a ferromagnetic body is magnetised to saturation, the resulting magnetostriction will be dependent on the distribution of magnetic domains in the initial state.In the literature two coefficients are used to describe the resulting magnetostriction at a saturating magnetic field. The total strain, measured from an arbitrary demagnetised state to technical saturation, is called the saturation magnetostriction, and is denoted by (~)s. The tenn magnetostriction coefficient will be employed to designate the strain measured from the ideal demagnetised state (i.e. one in which no preferred orientation of domains exists) to technical saturation. Failure to recognise the difference between these two quantities has led to considerable confusion in the literature.The magnetostriction coefficient for a single crystal is a well-known property for ferromagnetic cubic materials. In 1939 Becker and Doring [1] have derived the following relation, describing the magnetostriction coefficient for single crystals with a cubic symmetry:"

Jan 1, 2001

By Kandipati Sreenivasarao

Ion flotation is a promising separation process for continuously removing toxic metal ions from dilute process effluents. After treating the effluent with appropriate surfactant(s), the metal- bearing species adsorb onto the surface of rising gas bubbles and can be collected as foams. Suitable collectors have been identified for most of the elements of the periodic table. However, a better understanding of the thermodynamic, kinetic and engineering principles that determine the performance of ion flotation systems would facilitate commercial utilization of this technology. A model system of sodium dodecylsulfate-ethanol has been studied for the removal of Cu (11) from dilute solutions, using laboratory-scale flotation columns. This paper reports the effects of the air flow rate, solution height, foam drainage zone height and col1ector:metal ion ratio on the flotation kinetics, ultimate recovery of metal, flotation product grade, foam losses and effluent quality. Preliminary results for Pb (11) removal are also reported.

Jan 1, 1993

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By A. Onozaki

The Iijima Refinery was put into operation in 1972 and today has an annual production capacity of 156,000 tons of SHG electrolytic zinc. At the Iijima Refinery, the recoveries of gold and silver are 98.0% and 98.2%, respectively. Gold contained originally in the zinc concentrates reports in the Cu-Pb-Ag residue produced in the residue treatment process. Silver contained in the concentrates is distributed between the Cu-Pb~Ag residue and the copper cake produced in the purification process. The Cu-Pb-Ag residue, which contains gold and silver, is sent to the Oyachi flotatfon plant of the Kosaka Smelter; about 82% of the gold and about 85% of the silver are recovered in the copper flotation concentrate.. In this paper, the distribution of gold and silver in the Iijima. Refinery is discussed and operational results of the Oyachi flotation plant are presented.

Jan 1, 1990

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Deqing Zhu

"An innovative process of reverse floatation-direct reduction-low intensity magnetic separation was developed to effectively beneficiate the superfine run-of-mine (ROM) ore mined from Hunan Province, China. Mineralogy was measured that the ROM ore is of superfine low grade hematite ore type, assaying 27.2wt%Fetotal and with main valuable minerals of hematite occurring at size between 3 to 5µm. The upgrading results show that the final iron concentrate, assaying 88.3wt%Fe total and 94.5% metallization degree was obtained at an overall iron recovery of 69.9% under the following conditions: rough concentration by grinding of ROM up to 88.7% passing 0.074 mm and reverse flotation at pH=9.4, 100 g/t starch and 200 g/t dodecylamine (DDA), and coal reducing the rough concentrate pellets containing 12% calcium containing complex additive at 1200 oC for 120 min, and finally magnetic separation of the reduced pellets by grinding up to 89.2% passing 0.043 mm at 0.08 T field intensity.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 628 million ton in 2009 [1]. Iron making industries increasingly demand for high grade raw materials to improve product quality and reduce operation cost. However, availability of high grade natural ores is limited and enrichment of lower grade ores is necessary to meet the demand. Therefore, large quantities of superfine low grade iron resources are necessary to utilize in China at the moment."

Jan 1, 2011

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013

By Ehsan Khajeh

In this study, the permeabilities of Al-15.5wt%Cu and Al-19.5wt%Cu have been determined by solving the full Navier-Stokes equations on 3D geometries of interdendritic channels obtained by X-ray microtomography (XMT). The samples for XMT were sectioned from different positions in directionally solidified cylinders in order to obtain a variety of microstructures for each composition. The flow has been solved using a 2nd-order accurate Finite Volume Method (FVM) approach. The effect of employing uniform or unstructured mesh on the calculated permeability has been studied. The Marching-cube triangulation method was necessary to extract accurate surfaces for unstructured volume meshing. Calculated values of permeability for this range of solid fractions show partial agreement with previous experiments. Observed deviations are attributed to the difficulties of experimental permeability measurements.

Jan 1, 2009

By Liu bing-guo, Peng Jin-hui, Guo Sheng-hui, Kong dong-cheng, Hu jin-ming, Zhang Li-bo

The novel technology of calcination to prepare triuranium octaoxide（U3O8）from ammonium uranyl carbonate in microwave fields was investigated on the basis of the temperature rising characteristics of ammonium uranyl carbonate, triuranium octaoxide (U3O8), and their mixture. The result of experiments show that ammonium uranyl carbonate had weak capability to absorb microwave energy, while triuranium octaoxide has the very strong capability to absorb microwave energy and the sample temperature increased rapidly with an increase mixture ratio of triuranium octaoxide. The optimal calcination conditions were as follows: microwave power 700 W, calcination time 10 min and 60 g in this experiments range, respectively. Under these conditions the value of total uranium and 4 U of triuranium octaoxide was 84.28% and 31.02%, respectively. It is feasible to prepare triuranium octaoxide by calcination from ammonium uranyl carbonate, which mixed with small amounts of triuranium octaoxide under microwave fields.

Jan 1, 2015

By T. Johnson, B. Q. Li

"Electromagnetic stirring has found a wide application in metals processing for the benefit of obtaining refined solidification microstructures. This paper presents an experimental study on the melt flow and turbulent behavior in an electromagnetically stirred Woods metal pool. The experimental setup consists of metal bath unit equipped with temperature control to allow both cooling and heating, velocity probe positioning unit and data and signal acquisition and processing unit. The whole measuring system is under the control of an IBM personal computer. Velocity measurements are made using the incorporated magnet probes, which are calibrated using a turntable. The measured results showing the effect of the coil positions, coil arrangements and the applied currents on the melt flow are presented. Both mean flow and turbulence quantities are discussed.1. IntroductionElectromagnetic stirring is widely practiced in the metals industry for melt mixing and for casting microstructure refinement. Industrial examples are taken from induction furnaces where the electromagnetic forces are applied to generate desired melt mixing and also various types of electromagnetic stirrers used in various stages of steel and/or aluminum casting processes to produce fine grain solidification microstructure or to eliminate undesired defects such as TCG (twinned-columnar-grain) structure. For ultrahigh purity aluminum or high strength aluminum alloys containing zirconium or lithium, grain refinement can be difficult with the conventional technique, and electromagnetic stirring provides a particularly powerful means to obtain the refined solidification microstructure [1]. A fundamental understanding of the melt flow and the turbulence characteristics in these magnetically-driven flow systems is of significant engineering importance to both process design and product quality improvement.There exists extensive literature on the magnetically-driven melt flows in material processing systems. Nakanish. et al. [2] were perhaps among the early investigators to mathematically and physically model the magnetically-driven flow phenomena in molten metal systems. Subsequent theoretical and experimental work by Tarapore and Evans [3, 4], Szekely and Chang [5], Hunt and Moore [6] and Szekely and El-Kaddah [7] has contributed very significantly to our understanding of magnetically-driven flow in inductively stirred melts. They have developed mathematical models for the electromagnetic field and turbulent flow in induction furnace and validated the models by either laboratory experiments or direct measurements in the industrial-scale induction furnaces."

Jan 1, 1998

By Tim B. Vander Wood

Standard methods of determining clay mineral powder aspect ratios involve manual scanning electron microscopy analyses of shadowed particles in order to measure both platelet thickness and diameter. We present a method whereby the diameters of platelets are quickly determined by automated scanning electron microscopy and their images are recorded and digitally transferred to a transmission electron microscope equipped for parallel electron energy loss spectroscopy. Thickness' of platelets whose diameters are known from the previous analyses are determined by measurement of the ratio of scattered and unscattered electrons in the beam after it has been transmitted through the platelet.

Jan 1, 1995

By J. Phillip Mackey

The Peter Hayes Symposium on Pyrometallurgy, held as part of Extraction 2018, is an acknowledgement of his contributions to the basic science and principles underpinning modern pyrometallurgical processing. After completing his PhD at Strathclyde University, Scotland, in 1974, Peter took up a teaching position at The University of Queensland, Brisbane, Queensland, Australia in 1976. Peter Hayes’ research at the University since then has been focussed on: • The mechanisms and kinetics of heterogeneous solid/solid, gas/solid and liquid/ solid reactions, and • Experimental measurement of phase equilibria in complex high temperature metallurgical systems. This paper provides a brief biography of Dr. Peter Hayes and gives a full listing of Peter Hayes’ publications.