Search Documents

By Xin Zhang, Mengqi Li, Hongxu Li, Xinrong Zhang, Hao Bai, Ning Li

"Organic Rankin Cycle (ORC) is an effective technology to transform low-grade energy resource into electricity. In this paper, based on thermodynamic principle, considering the waste heat resource lower than 120°C, thermodynamic properties of ORC with working fluids ofR245fa, mixed R21/R245fa and mixed Rl52a/R245fa were assessed. The results show that high evaporation temperature contributes to improved system performance. The Rankine Cycle that uses R21/R245fa can increase net cycle output, thermal efficiency and exergy efficiency by 3.02%, 2.35%, and 4.44%,respectively, as compared to that with pure R245fa. When using Rl52a/R245fa as working fluid, the net cycle output can increase by 3.83% at most, while the thermal efficiency decreases by 8.7%. These results indicate that R21/R245fa has a good advantage in improving the cycle thermodynamic performance.IntroductionOrganic Rankine cycle is usually used for low temperature power generation, and is applied to the conversion of geothermal energy, low-temperature solar energy, ocean thermal energy and industrial low-temperature waste heat etc. Traditional Rankine cycle is quite mature already, however, organic working fluids would affect significantly the general efficiency of the entire thermodynamic system. Thus, selection of proper working fluids and development of new highperformance cycle is becoming important."

Jan 1, 2013

"An experimental study has been performed to investigate the dispersed phase holdup induced by a high-strength submerged gas injection in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor using two different tuyere configurations. The air flow rates varied from 0.00599 m3/sec to 0.01312 m3/sec. In these series of experiments, water height and kerosene height were kept constant at 0.23m and 0.02m respectively. The dispersed phase holdup was determined at various gas flow rates, and tuyere orientations by using water and kerosene.The dispersed phase holdup increased with gas injection rate and decreased with vertical distance from the original interface. At constant gas flow rate, as the vertical distance increased in the centerline, off-center configuration of nozzles displayed higher values of the dispersed phase holdup than those of the center configuration. The variation of the dispersed phase holdup with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the calculated values obtained from the correlation equations."

Jan 1, 1999

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By R. A. Sharma

Neodymium metal was successfully produced by the reduction of Nd203 with Na in the presence of CaC12-NaCl melts by the overall reduction reaction Nd203 + 3 CaC12 + 6 Na ? 2 Nd + 3 CaO + 6 NaCl at -750°C. The metal produced was extracted from the salt media by dissolving it in a Nd-Fe alloy pool. The yield (percentage of theoretical neodymium produced) was found to depend on the salt composition and the mass ratio of salt to neodymium in the reactor. A yield of 95% was obtained with salt ratios as low as 3.5. Further decrease in the salt ratio below 3.25 decreased the yield. Stirrer position had little effect on yield; while increasing the temperature and placing fins in the reactor increased the yield. The Nd-Fe alloy produced was of as good quality as that produced using Ca reductant, and was suitable for direct use in producing General Motors MAGNEQUENCH? alloy for permanent magnets.

Jan 1, 1989

By L. A. Neumeier

The Bureau of Mines, U.S. Department of the Interior, is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide .phases by sulfldation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes initial research involving sulfidation partitioning of chalcopyrite concentrates. Small chalcopyrite samples were sulfidized with elemental sulfur in glass capsules sealed after evacuating and backfilling with helium, by heating for 1 to 24 h at specific temperatures in the range of 250° to 500° C. which extends from below to above the boiling point of sulfur (-445° C). Above the boiling point of sulfur, the overall reaction with adequate sulfur (13.9 wt pct of CuFeS2) is 5CuFeS2 + 4S g ? Cu5FeS6 + 4FeS2.

Jan 1, 1989

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000

By John T. Berry, Robert D. Pehlke, Michael J. Beffel

"Pattern making and metal casting organizations are currently adopting CAD/CAM systems and implementing this technology in design and production. Al though significant progress has been reported, these systems generally are based on two or two and one half dimensional analyses. Very few are based on solid geometric modelers.The present paper emphasizes the need for solid geometric modeling of the casting and rigging system and linkage with a solidification simulator. The nature of some of the technological challenges which have slowed this development are discussed, including accurate description of complex surfaces and their intersections and the bridging of computer encoded information with NC technologies and with FEM-based simulators for stress and thermal analyses. A recently prepared modular-structured FEM simulation code implemented on a micro computer is described.Construction of a solid geometric model of the casting and rigging and validation of the combination for optimum characteristics of soundness, quality and yield by solidification simulation are I inked as key elements in the foundry of the future. Data base support for this CAD/CAM system is rapidly being developed throughout the world.INTRODUCTIONThe simulation of shaped casting solidification using the digital computer, goes back to at least the early nineteen-sixties when Forsund (1) in Denmark applied the technique to the problems of casting surface quality.Prior to that time, the work of Paschkis and co-workers using the analog computer ranges back to the nineteen-forties, when work sponsored by the AFS Heat Transfer Committee at Columbia University revealed many hitherto unknown or only partly anticipated aspects of casting solidification (2).Three reviews of the various historical aspects of simulation should be referenced. Firstly, the AFS monograph by one of the present writers (RDP) and his colleagues - describing background and later work, again sponsored by the AFS Heat Transfer Committee at the University of Michigan (3). Secondly, a review prepared by Durham and Berry (4) which discusses broad aspects of casting solidification simulation. Thirdly, a review by Erickson (5) which contains an excellent bibliography to 1980. In addition to these papers, the publications lists of the CADCAST project* and the proceedings of the two Engineering Foundation Conferences of Casting and Welding Modeling, published by ASME, are also most notable (6) •"

Jan 1, 1986

By S. -H. Jeon, Y. -S. Choi

"The three dimensional current distribution on the rectangular cathode is predicted using a boundary element method with a linear element of trigonal type. The effect of cell geometry and anode shape on current distribution is simulated. Calculated results compare well with experimental results. The proper combination of anode size and distance between electrodes increase the current uniformity.The importance of electrodeposition as a fabrication technology in the electronics industry is large and growing. The main advantages of this wet processing method, in comparison to other dry processing methods, lie in its high yield, rapid processing and low cost. In nearly every application of electrodeposition the pursuit of deposit uniformity, especially thickness uniformity, has been technically imperative. The thickness uniformity of the deposit depends largely on the current distribution over the cathode. The current distribution is primarily determined by the geometrical characteristics of the electrodes and the cell. Also the polarization at the electrode surface and the mass transfer affect the current distribution.The current distribution is an important consideration for those involved in designing electrochemical systems and electroplating systems in particular. Although it is important, the common practice in industry is to use trial and error method to design the cell that optimize the uniformity of current distributions in electroplating. The purpose of this paper is to illustrate the useof boundary element method to predict three-dimensional current distribution in rectangular cell.The calculation of the current distribution is possible by various numerical techniques, which include the finite difference method (FDM)1, the finite element method (FEM)2, and the boundary element method (BEM)3,4. These methods of the numerical calculation have various problems, respectively, but the BEM is considered to be the most efficient. This is due to the fact that the BEM has the advantage of solving field equations only on the surface of a calculation domain. A good comparison between the BEM and the FEM for the secondary current distribution in a Hull cell was made by Matlosz et al.5The fundamentals on the theory of current distribution in electroplating are well-established in the literature by a number of authors.6, 7, 8 However, a small fraction of these works have been specially addressed to three-dimensional analysis, and, mostly thel·10 have focused on the problem qualitatively rather than quantitatively.Extending the previous work to three-dimension, we developed the program for the quantitative calculation of 3-dimensional current distribution using a boundary element method with a linear element of trigonal type. Integrals with singularity from the fundamental solution have been analytically computed and it is shown in detail in the Iiterature11. This paper deals with the three dimensional current distribution for the electrode position of copper in a cubic type cell and the effect of anode shape, size and the distance between electrodes on current distribution is studied."

Jan 1, 1997

By Mike Adams

Comprehensive pilot testwork has been conducted on BHP Billiton's Ravensthorpe nickel laterite deposit over a fifteen-month period at Lakefield Oretest. Some 228 tonnes of ore were processed in a beneficiation pilot-plant comprising scrubbing, attrition scrubbing, screening and thickening over sixteen pilot runs with an average mass closure of 99.2%. This produced a suitable feed for hydrometallurgical piloting over seven runs covering 1,680 hours of operation. The integrated EPAL® (enhanced pressure acid leach) circuit comprised a limonite pressure acid leach front end discharging into a saprolite atmospheric leach circuit and subsequently to induced jarosite precipitation, counter-current decantation, iron removal, mixed hydroxide precipitation, and manganese removal. The pilot plant met its key objectives in demonstrating the flowsheet's technical viability, and generating raw data inputs for the project feasibility study. Rapid, intensive data capture, collation and reporting helped solve key flowsheet issues. The pilot plant also demonstrated its value as a risk management tool in the resolution of numerous engineering, metallurgical and materials selection issues at a manageable scale. A disciplined approach to experimental planning, operation and management was a significant contributor to the overall success of the campaign. Keywords: Ravensthorpe, Nickel, Piloting, Beneficiation, Pressure, Leach

Jan 1, 2004

By Claudio Toro, Alex Moyano, Rodrigo Díaz, Hugo Jara, Carlos Caballero, Pedro Morales, Leandro Guzmán

"During 2007, Codelco-Chile carried out industrial tests to validate the Continuous Converting Process in the Teniente Converter of the Codelco Norte smelter.For planning and starting up the tests, a predictive, analytical and dynamic model was developed to support operational decisions. The dynamic model was developed using the METSIM® platform and dynamic data exchange (DDE) to operate smoothly with MS Excel®. The main feature of this real-time model was the on/off-line ability to work and gather data from either the smelter’s PI system® or database, and simulate the operation with or without scheduled events and controls.The main model development aspects, which include thermodynamics, metallurgical and kinetic considerations, slag-type and on-line mass and heat balances of the process, as well as the successful validation of the model, are presented and discussed in the present paper."

Jan 1, 2009

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By S. S. Ryu, J. C. Kim, H. Lee, Y. D. Kim, I. H. Moon

"Recently, W-Cu alloy becomes one of the very important candidate materials for heat sink and packaging in the field of microelectronics due to its good thermal properties. The metal injection molding of W-Cu powder can satisfy the requirement for mass production of complex shaped parts in microelectronic devices. In the present study, the application of MIM process to the nanostructured W-Cu powder prepared by mechanical alloying was investigated. The multi-component binder system of 45PW+ l 5BW+ 30PE+ I OSA was proven to be suitable one for the MIM of the W-Cu composite powders by adopting the debinding cycles of multi-stage in N2 and H2 atmospheres. Other process conditions for the MIM of the nanostructured W-Cu composite powder were also studied. The MIM debinding part of W-30wt.%Cu was sintered to the relative density of more than 96% by sintering at 1200 °C for !hour in H2 atmosphere. Such an improvement of sinterability was attributed to the intrinsic homogenous and fine mixing state of W-Cu phases in nanostructured W-Cu composite powders, and also partly to the effect of the activated sintering by the presence of impurity introduced during the extensive milling.IntroductionW-Cu alloys have been widely used for heavy duty electrical contacts and arcing resistance electrode(1-2). Recently there has been a growing interest in this W-Cu alloy because of its superior thermal managing properties and its high micro wave absorption capacity(3). Such W-Cu alloy parts are conventionally fabricated either by the Cu infiltration sintering technique or by hot pressing of W-Cu powder mixtures. However, these conventional PM techniques are hardly applicable for mass production of small size parts with a complicated shape such as the parts required for microelectronic devices. The metal injection molding(MIM) technique is potentially applicable for the mass production of small and complicatedly shaped parts compared with other PIM forming techniques."

Jan 1, 1998

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By Jingbo Liu, Zhimin Wang, Wenchao Li

"IntroductionThe advantages of non-stoichiometric perovskite material are highlighted in many papers[l]and many of this family of materials are well-suited to integration into microsensor devices. Among them, barium titanate is the most promising due to it's piezoelectric, pyroelectric, dielectric properties. Through modification, BaTiO3-based materials can be utilized in many kinds fields, such as surface wave probe; pholoconducting devices, field-effect transistor, permanent memory permanent storage, and ultrasonic transducerl2-3l. In this Paper, a series of BaTiO3-based polycrystals were synthesized by sol-gel processing which appears to be a very promising method for the manufacture of ceramic, because it offers significant advantages such as high purity, chemical homogeneity, controlled particle sizes of ceramics, and lower processing temperatures [4]. In a sol-gel process, alkoxides of the constituent elements show different reactivity toward water so that the preparation of multi-component homogenous system is difficult. In the experiment, inorganic salt was substituted for some of the alkoxides. Acetic acid which is employed for the solvent and catalyst, acts as donor ligand to titanium alkoxide and controls, the hydrolysis polycondensation reaction. Taking these aspects into consideration, we select the system Ba(OAc)2, , La(OAc)3, Ti(O11Bu)4 and acetic acid which is used as both solvent and homogeneous catalyst for the first time.ExperimentalA series of La3+-doped BaTiO3-based nano-crystals were prepared with sol-gel technology using various parameters. The precursor solution was prepared in the presence of barium acetate, lathanium acetate, and titanium tetrabutoxide monomer in butyl alcohol. According to the flow chart (fig. I.), Ba(OAc)2, La(OAch dissolved in the glacial acetic acid (0. lmol/40ml) in a three-neck flask were mixed with a solution of titanium tetrabutoxide monomer in butyl-alcohol(l 7ml/20ml) at room temperature and under constantly, vigorous stirring conditions. In most cases, the resultant solution was golden yellow and stable in the air. To this precursor solution, containing Ba, La, Ti in the desired ratio, water was added incrementally for hydrolysis under continuous stirring until sol was formed. After aging for more than 2 hours, sol was transformed to gel at room temperature. If heated during aging, the gel was formed in a shorter time. The wet gel was allowed to dry at 50°C for more than 10 hours. The dried gel was transparent or light yellow. In order to obtain BaTiO3-based nano-crystals, the amorphous dry gel was calcined at 600°C, 700°C, 800°C, 900°C, 1000°C respectively[5]. The ceramic humidity sensor was formed through the cold-pressed, aged, capsulated routes. The dried gels were crushed in an agate mortar and then pressed into discs of ? 1.5 X l.5mm (l.5mm diameter and l.5mm thickness), then held at about 16.5 MPa pressure for 3 min [6]. The disc was sintered at 1350°C and 1400°C for I hour respectively. During the processing, an Ag-Pt electrode was inserted in the sensor [7]. (See the flow chart.)"

Jan 1, 2000

By Zuoren Huang

The flowsheet of the hyd.rametallurgical zinc plant which is in use at Zhuzhou Smelters is described. The principal features of the process are fluid bed roasting, continuous calcine leaching, solution purification, zinc electrolysis, electrolyte cooling, and finally, the melting and casting of zinc forms. The Zhuzhou process for the flotation of silver from the leach residue collected on the Moor filters is described. The technical details of the process are outlined and the operating data are analyzed. The flotation facilities are described in detail and concentrate grades and recoveries are presented. The waelz process is used to concentrate In, Ge and Ga remaining in the leach residue after silver flotation. These elements subsequently are recovered by selective leaching in sulphuric acid, and details of this operation also are presented.

Jan 1, 1990

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to 'low-Cu-grade' FeS2-CuFeSz concentrates. Chapter 14 does the same with 'high-Cu-grade' CuzS-CuFeSz?concentrates.

Jan 1, 2001

By Tatsuzo Kitamura

The tank house of Tamano refinery, that started its operation in January, 1972, was constructed incorporating the application of Periodic Reverse Current (P.R.C.) from the outset of design works. In 1973, the production of electrolytic copper came up to 8,000 mtpm, a sharp increase ds compared with the designed capacity of 7,000 mtpm, and successful operation has been achieved up to the present. P.R.C. has been employed for the purpose of raising productivity level and reducing copper inventories. Since there were various problems in P.R.C. application to such a large sized cathode as 1 m x 1 m, special attentions were paid to the following items: -Development of a unique bus bar to make an electrolytic current to each electrode as uniform as possible. -Improvement of circulating method of electrolyte. -Application of high-performance equipment to realize a uniform spacing between anode and cathode. Owing to these creative technical developments mentioned above, technical level for operation up to 350 amp per sq m of cathode current density has been established. The quality of electrolytic copper, which was a matter of interest, has been proved to be as excellent as those of conventional electrolysis products through a long term supply to the field of SCR and Dip forming where high levels in quality are required.

Jan 1, 1976

By Philip Nash, Jie Zhou, Joshua Blackketter

"Large ingots tend to have internal defects such as shrinkage cavities and porosities, which have to be closed during the cogging stage to ensure sound internal quality of forged parts. In this work, finite element methods were used to simulate open die forging passes, with varying parameters that affect the void closure behavior profoundly. Numerical models ware constructed in ABAQUS, DEFORM and FORGE using data taken from footage of the forging process and material mechanical data obtained from the Gleeble compression tests. Forging variables such as pass rotation, reduction per pass, and feed ratio were studied with intense attention paid on the special properties of H13 steel, so that this study can be applied to solve real world problem.IntroductionCenterline defect closure is a frequently studied but still challenging topic in open die forging industry. In practice, open die forging is employed as an effective hot forming process to make desired shape of metal products as well as to ensure center consolidation of internal defects which result from the casting process. Nowadays, remarkable large forgings have been more and more required to meet industries demand. However, the increase in ingot size has tended to result in considerable macrosegregations and shrinkage cavities or voids, which need to be worked thoroughly during the forging process; but the size of the products and limitations of manufacturing capacity, such as the press load, make it difficult to achieve adequate local deformation to close those defects. Therefore, choosing optimal forging parameters under given work condition to ensure good internal quality of forged products is critically important."

Jan 1, 2012

The generation of acid mine water is? due to the oxidation and weathering of sulfide bearing tailings and overburdens. Ferrite precipitation prooess has been applied to treat acid mine water. The conventional ferrite preC1pitatlon requires air oxidation at high temperature, or long aging time or addition of magnetite powder ,as promoter. In this investigation, a modified ferrite, precipitation process is developed by which magnetic ferrite can be produced at an ambient temperature. Acid mine waters from Berkeley Pit (Montana, U. S. A.) and from Noranda Tailings (Quebec, Canada) were used. The co precipitation of heavy metals from these two acid mine waters is studied as a function of FeIM molar ratio, oxidation time and settling rate under applied magnetic field. The investigation indicates that the modified ferrite co precipitation can remove substantially all of the, dissolved metal ions from acid mine water. The ferrite product obtained after precipitation' is characterized by XRD, SEM, BET and saturation magnetization. The results show that spinel ferrite, precipitation can be achieved at room temperature and the saturation magnetization of ferrite product from,acid mine water is comparable to that of pure ferrites.

Jan 1, 1995

By A. A. Hejja

"Liquidus temperature and electrical conductivity data measured on synthetic slags were modelled by the use of neural nets (NN). In this work the applied multilayer feedforward NNs were trained by a conjugate-gradient optimisation for which a three layer formulation was used. Very good fits were obtained for both the liquidus temperature and the conductivity data. The synthetic slags were prepared from pure oxides to represent a wide range of compositions likely to be encountered in ferromanganese and silicomanganese smelting. The slag constituents were in the following range: Mn0;5-30%, Ca0;20-35%, Mg0;5-15%, Si02;27-58%, Al20 3;5%. Liquidus temperatures varied from 1300° to 1380° and increased with increasing basicity ratio. The electrical resistivity of slags decreased with the increase of basicity ratio from 0.55 to 1.1 but above 1.1 basicity ratio the resistivity tended to increase depending upon the MnO content.Neural NetsVarious neural net (NN) topologies such as Hopfied nets, Hamming nets, Carpenter/Grossberg classifiers have been discussed in some detail by Lipmann (1). In this work, the applied multilayer feedforward NNs are not trained by backpropagation (BP) using the generalized delta rule (2) (GDR), but by a conjugate-gradient optimisation [3,4] - a procedure similar to that proposed by Barnard and Cole [5]. A neural net is capable ·of learning the non-linear functional relationship existing between a set of inputs and outputs [ 6]. In this capacity a neural net is used to determine the functional relationship that exists . between N dependent and independent variables, which characterize the system under consideration For a three layer neural net [1] the following function may be formulated, which relates X; inputs to the output Y 0 from node o:"

Jan 1, 1997