Search Documents

By Lztok Peruš, Goran Kugler, Matevz Fazarinc, Milan Tercel

"Hot deformability of M42 tool steel additionally alloyed with cobalt and molybdenum was investigated. Hot-compression tests were carried out in the temperature range 850 °C -1200 °C, at strain rates range 0.001--6s-l up to strain of0.9. Field-emission scanning electron microscope and optical microscopy were used for characterization of microstructure of deformed samples, which revealed a very complex precipitation of carbides that strongly depends on the soaking temperature, the soaking time, the stress state, the deformation temperature as well as on the strain rate. Gathered data was used to calculate the processing parameters such as process maps, apparent activation energies and strain hardening exponents. For better understanding of thermodynamical properties of the studied steel a simultaneous thermal analysis was conducted. Furthermore the analysis of phase equilibrium was calculated using Thermo-Cale software. On the basis of these studies the optimal soaking temperature and process windows were determined.IntroductionHot workability ofledeburitic tool steels is important economic factor. This means that for each tool steel individuallysafe range of hot working parameters should be revealed. Publications in the literature with regard to the hot workability of tool steels are rare and therefore more information from this research area is desired.The relatively low hot workability of ledeburitic tool steels, i.e. steels in which the solidification is completed by a eutectic transformation of the residual interdendritic liquid to austenite and various alloy carbides (ledeburitic carbides), is usually characterized by the production of surface and internal cracks during the hot deformation."

Jan 1, 2013

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

By Jun Li

Several metal sulfides were examined in-situ by Raman spectroscopy before and after anodic oxidation. Results obtained for chalcocite, chalcopyrite, covellite, galena, pyrrhotite and pyrite electrodes are presented. Under appropriate conditions, sulfur was detected after a potential was applied to the mineral electrodes for a threshold period of time. For all the minerals, application of a negative potential on the oxidized mineral reduced the surface product and the sulfur peaks disappeared from the observed spectra. For those minerals containing sulfur as S< in the crystal lattice, polysulfides were identified as oxidation intennediates.

Jan 1, 1993

By Antonio Huerta

The effects of potassium ethyl xanthate collector and potassium dichromate used as a depressor on a PbS mineral were studied by high frequency impedance technique. Measurements of complex permittivity, at 100 MHz suggested that is possible to obtain from isotherm adsorption the adequate industrial collector concentration being this in the range of lE-3 to 5E-3M of KEX. The e&apos; values (320-420) in the PbS-KEX system was increased as the KEX concentration was lowered). In the other hand the PbS- K2Cr2O7 system showed higher values of e&apos; (420-510) as the K2Cr2O7 concentration was increased. The PbS-KEX-K2Cr2O7 system was evaluated.

Jan 1, 1997

By T. T. Chen, J. E. Dutrizac

"Grooved cast Pb-Ag anodes are used by some zinc refineries to improve current efficiency. It was found that the manganese oxide scale formed on a grooved Pb-0.75% Ag anode consists mainly of MnO2, which occurs characteristically in rhythmically banded colloform structures and adheres to a layer of ""Pb02+PbS04"" that oxidized from the anode. The relatively homogeneous and nearly fracture-free morphology of the ""Pb02+PbS04"" layer suggests the relatively uniform corrosion of the anode. Deposition of the Mn oxide initially follows the contours of the anode surface, but the grooves eventually become filled with Mn oxide and gypsum. Hydrous Mn oxides and amorphous Mn oxides are believed to be also present in the manganese oxide scale. Tiny particles of PbS04 and SrS04, together with gypsum, other impurities and micro-pores, tend to concentrate in the grooves.IntroductionManganese is a common impurity in hydrometallurgical zinc processing circuits. The manganese originates from sphalerite (Zn,Fe,Mn)S and from the Mn02 added to the leaching circuit to oxidize ferrous ions [1]. Manganese in the sphalerite follows Zn through the roasting, leaching and purification processes, and is present as Mn(II) in the purified ZnS04 solution. The Mn in the added Mn02 is reduced to Mn(II) during the oxidation of the ferrous ions present in the leach solutions. In both cases, MnS04 is generated, and the MnS04 accumulates in the purified solution. In the cellhouse, Zn is plated at the cathodes to produce high quality metal. The Mn(II) is partly oxidized at the anode surface to Mn(IV), and the Mn(IV) precipitates as a scale on the surface of the anode and as a sludge on the bottom of the electrolysis cells. The presence of a thin layer of manganese oxide scale on the surface of the Pb-Ag anode can minimize the corrosion of lead and, accordingly, reduce the contamination of the electrodeposited zinc. However, a heavy manganese scale build-up can cause ""staining"" of the zinc deposits and reduced current efficiencies. Consequently, periodic anode cleaning to remove excess manganese oxide scale is carried out routinely in commercial operations."

Jan 1, 2011

By Mehdi Asgharifar, Rouzbeh Sarrafi, Radovan Kovacevic

"The surface treatment of aluminum alloys using atmospheric-pressure of low intensity DC plasma arc discharge is investigated in terms of surface properties. With respect to the conventional surface treatment processes for aluminum alloys mostly based on chemical etching or sand blasting, this process is very environmentally friendly and cost-effective. The effect of two processing parameters, the current and the plasma torch scanning speed, on the surface morphology is studied by using a scanning electron microscope. The effects of cathode spots within the tested range of process parameters are determined, and the limiting factors of the process (such as surface cracking) are discussed. The topographical studies of the treated surfaces have suggested potential enhancement of surface properties for different applications, such as preparing surface for painting and adhesive bonding.IntroductionIn the last decade the aluminum alloys are finding broad applications in automotive industry. In order to successfully execute the joining process of aluminum alloys such as arc welding, laser welding, and adhesive bonding, there is a need to remove oxides for welding and texture the surface for bonding along the join line. A number of surface treatment techniques such as chemical etching, sand blasting, and plasma treatment have been used by industry. It is shown [1] that plasma surface treatment is characterized as environmentally friendly, lower cost, and easier to control process. Bogaerts et al. [1] mention that when an adequately high potential difference is applied between cathode and anode, electrons are accelerated toward anode by an electric field coming in collision with gas atoms. The gas breaks down into positive ions and electrons, giving rise to gas discharge. The DC electrical discharges used in industrial plasma sources can be related to their location on the voltage-current curve as shown in Figure 1.It is generally believed that dark discharges other than coronas, and arc or torch plasmas are not very good candidates for surface treatment because oflow or high power density and active species flux. However, the glow discharge plasma is used for plasma surface treatment applications because of its proper power density and active-species flux [2]. Our objective is to investigate the feasibility of using low intensity DC plasma arc discharge as a surface treatment method without damaging the cathodic non-thermionic workpiece."

Jan 1, 2011

By Toyohisa Fujita

The effect of variables on the gold extraction with ammonium thiosulfate was investigated on sponge gold and ore samples. The Effects of CUS04, (NH4hS203, NH40H, (N~hS04&apos; pH, stirring speed and retention on gold leaching rate and thiosulfate oxidation (consumption) have been studied. Almost 100% of gold was leached from sponge gold and over 96% from ore sample at optimum conditions. Trioctylmethyl ammonium chloride was used to recover gold from thiosulfate pregnant solution. It was found that more than 99% of gold was recovered by the extractant diluted with n-octane at 01 A ratio of 1: 1 without the re-adjustment of pH or others. Also, the gold cementation was conducted without de-aeration by using zinc, copper and aluminum powders. The result indicated that the gold was effectively recovered from a solution of low ammonia and copper concentrations and higher thiosulfate concentration. The gold recovery process by using ammonium thiosulfate is an environmental friendly method comparing to conventional cyanidation process.

Jan 1, 2003

By Chen Dong, Yuanling Gao, Jilai Xue, Jun Zhu, Luxing Feng

"Porous Ni-Ti alloy has many applications in a wide range of engineering areas. The porous NiTi alloys were prepared from Ti and Ni powders in sintering process under argon atmosphere. The major chemical compositions of the sintered Ni-Ti body were Ni Ti, Nh Ti4O and Nh Ti, respectively, the internal pore structures were characterized by image analysis technique, which were dependent on various processing parameters such as sintering temperature, amount of poreforming agent, forming pressure, etc. The results show that the porous alloy samples had the characteristics of uniform pore and high open porosity; pore-forming agent and sintering temperature are important factors in porous; pressure affected the sintered products' pore, by affecting the combination of alloy powder with pore-forming agent.IntroductionPorous Ni-Ti alloy materials exhibit not only excellent shape-memory and superelasticity, high yield strength and ductility, good corrosion resistance and biocompatibility, but also have low density, low stiffness, and high energy absorption rate due to their porous structures [1]. In recent years, these porous Ni-Ti alloys have found applications in a wide range of engineering areas, such as bone implants [2-4], impedance-matching connectors [5], energy-absorbing structures [6,7], separators [8] and actuators [9], etc.Pore characteristics can play very important role in determining of the performance of porous NiTi alloys. For example, when the alloys are used to repair or replace hard tissue implant material, the pore shape and size not only determine their mechanical properties, but also have great effect on the fluid transmission of human body. The pore characteristics can also influence the stressstrain behavior of the porous Ni-Ti alloy and, thus, strongly affect their mechanical properties, superelasticity, and fracture mechanisms [10].In this study, the Ni-Ti alloys with high porosity were prepared in a powder sintering process under argon gas. The pore characteristics were investigated using SEM, XRD and image analysis techniques, especially in association with the content of pore-forming agent, sintering temperature and compacting pressure."

Jan 1, 2011

By C. M. Egert, S. Rajic

"We have developed a monolithic micro-spectrometer suitable for a variety of sensing applications including industrial process monitoring. The device consists of a solid structure with a volume less than 6 cubic centimeters. All optical components of the spectrometer including two aspheric mirrors, a diffraction grating, and entrance and exit surfaces are fabricated onto the surface of the structure. All light paths are internally contained within the structure. The result is a small, rugged spectroscopic sensor ideally suited for use as a process monitor. Due to its monolithic nature the device requires no post-fabrication alignment; nor can it be knocked out of alignment during use. Although many materials and thus wavelength regions were possible, the prototype device discussed here was produced in PMMA by precision diamond turning. However, lower cost manufacturing approaches involving injection molding are under development to produce an affordable sensor.Due to its rugged monolithic design, small footprint, and low cost the monolithic micro-spectrometer is ideally suited for distributed monitoring applications often required for industrial processes. It is expected that modified versions of this sensor designs will be required for specific applications so as to maximize the performance and resolution over the operating range. For example, the prototype device described here operates over a wavelength range of 500 nm to 1000 nm. The performance of this device as a real-time surface monitoring sensor will be discussed in detail. Our approach of using wavelength dependant scattering resulted in the reduction to practice of a miniature, monolithic, rugged, low-cost, micro-instrument in a sensor sized package. The process sensor applications community has been faced by the cost versus performance issue. Simple go/no-go sensors are typically inexpensive but they provide very limited and sometimes dubious data. Scaled down traditional instruments offer very good measurand information but are typically cost prohibitive, fragile, and still relatively large. This work will bridge the gap between these two extreme sensing alternatives."

Jan 1, 1997

By L. W. Beckstead

The use of acid ferric sulfate solution as a lixiviant for chalcopyrite concentrates has been of little interest from a practical standpoint due to the formation of a tenacious layer of elemental sulfur which severely impedes the reaction progress. CuFeS2 + 4Fe+3 ?Cu+2 + 5Fe+2 +2s° For example, an acid ferric sulfate leach of chalcopyrite concentrate results in only 12% copper extraction in a three hour leach at 93°C. Experimental results suggest that particle size is the only controllable variable which has a significant effect on the rate of acid ferric sulfate leaching at ambient pressure. Size reduction of the concentrate prior to leaching was exam¬ined using various methods of grinding. Of the grinding methods considered, attrition grinding was found to be the most effective. Leaching of an attritor-ground product (median particle size 0.5 microns) resulted in approximately 90% copper extraction in a three hour leach at 93°C. Energy measurements suggest that the costs associated with attrition mill¬ing are not unreasonable. Evidence indicates that "activation" or stored strain energy is not responsibile for the enhanced reaction kinetics of the finely ground concentrate, but rather the experimental results can be explained simply in terms of the increased surface area due to size reduction. Leaching reaction mech¬anisms operative in the acid ferric sulfate system are discussed and the application of ultra-fine grinding technology to other systems is considered.

Jan 1, 1976

By Haotian Xue

A new process to extracted antimony directly from stibnite concentrate by reductive sulfur-fixation smelting in sodium molten salt has been presented. The influences of sodium salt content and composition, ferric oxide addition, temperature and time was investigated, respectively. The optimum conditions was determined as follows: W????: ??concentrate=40%, W??alt: ????concentrate =88.75%, WFe2O3 :Wconcentrate =55.13%, W??aCl: ????alt=40%, 1123K, 1h. Under above-mentioned optimum conditions, the average direct recovery ratio of antimony can reach 91.48%, and the main chemical composition of obtained crude antimony is Sb 94.31%, Fe 4.436%, Pb 0.502%, Au 0.0236%. In comparison to traditional antimony pyrometallurgical process, the smelting temperature of present process is reduced from 1423~1473K to 1123~1173K. During the smelting operation, SO2 emision can be avoided completely due to sulfur-fixation as FeS. Furthermore , S0 can be obtained when the molten slag is handled by water leaching with conditions of 323K, L/S=5/1, 2h.

Jan 1, 2014

By Yoshiaki Suzuki

Since 1973, Saganoseki Smelter & Refinery had operated two flash smelting furnaces together to produce 330,000 mtpy of copper. However, in 1990&apos;s, economical situation required the smelter more increased productivity to remain competitive. The program, to integrate two flash furnaces into one was carried out maintaining the same production. Modifications were done on the pneumatic concentrate drying system, concentrate feeding system, concentrate burner and furnace cooling system, etc. to double the, furnace throughput. A new large cryogenic oxygen plant was constructed replacing two old plants. Single flash smelting furnace operation has started in March 1996. This paper describes about details of modifications and operational results.

Jan 1, 1998

By Honglei Zhang, Yue Wang, Guotao Xu, Li Liu

The influence of rich oxygen atmosphere on the properties and structure of castables used in the hot wind pipe of blast furnaces was analyzed. Results show that the cold compressive strength of castables is affected by the change of rich oxygen volume in the wind pipe, the bulk density decreases and apparent porosity of castables increases with the addition of rich oxygen in wind pipe. With the addition of rich oxygen, the velocity of heat transfer increase and result of the steel shell become over hot out of safe limit at the thin lining in hot wind pipe.

Jan 1, 2015

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By N. El-Kaddah, V. L. Acoff, M. Arenas

"Control of the weld penetration, weld pool shape and temperature field in arc welding is critical to achieve the desired microstructure and mechanical properties in the resultant welds. This is particularly important in welding gamma titanium aluminides (y-TiAl) where the weld pool is relatively shallow and the temperature gradient in the heat-affected zone is quite steep. This paper investigates theoretically and experimentally the evolution of the shape of the weld pool for stationary gas tungsten arc welds in y-TiAl alloys. A mathematical model has been developed for predicting the electric current flow, the resultant electromagnetic forces in the metal, and the transient development of the temperature and velocity fields in the molten pool generated by a spatially variable heat flux at the arc-striking zone. The governing equations were solved numerically using the control volume technique. Welding experiments were carried out to determine the shape of the weld pool and the extent of the heat affected zone at different welding times for model validation. The numerical predictions were found to be in reasonable agreement with measurements. It is suggested that the model presented in this paper is likely to provide the information needed for predicting the microstructure and mechanical properties of y-TiAl welds. IntroductionIn recent years, there has been considerable interest in the welding of gamma titanium aluminides as a means of manufacturing high-temperature, high-performance components for turbine and automobile engines. These alloys are highly reactive, and must be welded in vacuum or inert gas atmosphere, rendering electron beam, and inert gas tungsten arc welding (GTA) to be the only suitable welding techniques for joining these materials [1-3]. The GTA welding is especially attractive because of its flexibility and relative cost-effectiveness. However, previous studies on the weldability and weld properties of these alloys using this process revealed a decrease in the mechanical properties in the fusion zone [4]. This is generally attributed to the change of the original duplex structure to a dendritic structure amplified by the shallowness of weld spot. Quantifying the effect of arc operating parameters on the geometry and temperature profile of the welding pool prior cooling is the first step for controlling the fusion zone microstructure and mechanical properties."

Jan 1, 1999

By R. A. Masumura, C. S. Pande, D. Agassi

"Grain size has a different effects on the critical current density (Jc) of high and low transition temperature (Tc) superconductors. In high Tc superconductors, the critical current density Jc across grain boundaries depends sensitively on the misorientation 8. It was pointed out by Pande that this dependence is directly related to dislocation structure of the grain boundaries i.e., it is due to dislocation cores and stresses. These ideas are developed further in this paper leading to a relation between Jc and 8. The analytical result is compared with the experimental results on bicrystals and used to explain the difference in behavior between high and low Tc superconductors.IntroductionThe grain size distribution and its evolution with time and temperature is important in determining the properties of high and low transition temperature (T c) superconductors. The distribution is a convenient function to characterize the processing of a high Tc material during sintering. For example, it is known that the maximum density of ceramic materials is obtained when the grain growth is reduced but grain boundaries are still mobile. For practical superconductors, the processing parameters are selected to achieve optimum properties: highest possible T c and maximum critical current (Jc). In terms of an average grain size, the requirements for optimum T c and Jc are sometime in conflict. In A15 type superconductors and even in NbTi, larger Jc have been measured in smaller rather than larger grain sized material. Conversely, in a high Tc materials like YBa2Cu307, higher Jc have been found in larger grain sized or single crystal specimens.Extended defects such as grain boundaries in low T c superconductors can be effective pinning agents for magnetic flux lines, thereby increasing the transport critical current density of these materials [1]. On the other hand, the transport critical currents in polycrystals of high Tc superconductors such as YBa2Cu307 is found to be relatively small (much smaller than those in single crystals of the same material) [2]. It is now known that grain boundaries in high Tc polycrystals can in many cases form ""weak links"" reducing the critical current density across them. This phenomenon can be studied more precisely by experiments on bicrystals, where there is only one grain boundary. It is found that the critical current density is quite sensitive to the misorientation angle of the bicrystal [3,4]. Although the original experiments were conducted on YBa2Cu307, other Tc superconductors have been shown to give the same result [5]."

Jan 1, 1994

By Noboru Masuko, Sachiko Ono

"The structure and composition of anodic films formed on aluminum in a borate solution have been investigated by using TEM and SIMS with respect to the effect of current density and electrolyte temperature. The film is composed of a boron-containing outer layer and a boron-free inner layer with disc-like crystals present at the interface. The thickness of the film formed at constant current density up to an identical voltage, decreases with increasing current density. The thickness increases remarkably with elevated temperature. The transport number of Al3+ estimated from the thickness ratio .of the cuter to the inner layers is 0.4 when the film is formed at the current density of 20 Am-2 at 60°C. It increases slightly with increasing current density and decreases significantly with increasing temperature. Content of boron in the outer layer increases 1.5 times when current density .increases 10 times. These changes in film structure and composition with electrolysis conditions must have a significant role in the determination of electric properties of anodic alumina films as a capacitor material.IntroductionThe growth of anodic alumina film in ·a neutral electrolyte proceeds at both film/electrolyte and film/substrate interfaces giving a duplex structure. The oxide layer formed at the former interface includes electrolyte anions while a-pure alumina layer is formed at the latter interface. The thickness ratios of each layer respectively represent transport numbers of Al3+ and 0 2 - (1). The film thickness and the incorporated anion content as well as transport numbers of both ions must affect the dielectric properties of the film as a capacitor material. However, the correlation between film structure and electrolytic conditions is not fully understood (2). For the further clarification of anodic film growth mechanism, more detailed characterization of anodic films in relation to electrolytic conditions is advantageous. In the present paper, therefore, the effect of current density and electrolyte temperature on the microstructure and composition of anodic barrier films formed in a neutral borate solution was studied. The films were characterized by direct observation using transmission electron microscopy (TEM) and depth profiles of constituent elements obtained by secondary ion mass spectroscopy (SIMS)."

Jan 1, 2000

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"The Center for Advanced Mineral and Metallurgical Processing is developing membrane production technology based on autocatalytic reduction of palladium from solution onto a unique, porous substrate. Surface membranes and catalytic structures are critically important to applications that range from hydrogen purification membranes to petroleum refining. Autocatalytic reduction processes represent a cost effective method of producing stable surface layered structures that have good working lives. These attributes are particularly important in the production of palladium alloy purification membranes used in hydrogen production. Although considerable research has investigated the interaction of hydrogen and palladium alloys, the mechanisms in play while the membranes form are not well understood. Preliminary research has identified three distinct deposition mechanisms and it appears that substantial control over the resulting membrane is possible.IntroductionPalladium-based membranes separate hydrogen from other gases because hydrogen is uniquely soluble in and readily passes through bulk palladium. As currently produced, palladium-based membranes are expensive and have short service lives. These circumstances are due in part to the lack of a complete understanding of palladium or palladium alloy deposition. The Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production.In membrane production, the palladium requirement depends on substrate surface properties such as surface chemistry, porosity, and roughness. Thin, defect-free membranes have been successfully produced on substrates of porous glass, alumina, and stainless steel. However, the differences in the thermal expansion coefficients of palladium membranes and porous glass or alumina substrates cause problems at operating temperatures. The use of stainless steel substrates is advantageous because stainless steels have thermal expansion coefficients similar to that of palladium and they are stable at the required operating temperatures (Wicke, E., Brodowsky, H. and Ziichner, H. ). Stainless steel is also readily available and relatively inexpensive."

Jan 1, 2012

By Dan Wang, Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Zhongfu Zhou, Hongwei Cheng, Changyuan Lu

The preoxidation of the ore has a profound significance to the concentration, separation and purification of nickel and copper from the lean complex ore. In this paper, the natural Ni-Cu sulfide mineral samples under the elevated temperature condition in air were investigated, as well as under isothermal condition at 600 oC in air. The mineralogical characterization was studied using XRF, ICP and the Rietveld method. The oxidation behavior and the element migration of the Ni-Cu sulfide ore were studied by XRD, SEM-EDS and TG. The XRD Rietveld method was successfully developed in the phase identification and quantification of this complex ore powder sample. The oxidative intermediates (Cu/Ni-ferrite) were detected by XRD, and the process of the element migration was obviously revealed by the line scans using SEM-EDS. It is the preoxidation of this mineral that provides guidance for the extraction of valuable metals from low-grade Ni-Cu sulfide ores in the future.

Jan 1, 2015

By Chang Wei, Fan Zhang, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Marmatite is an important resource of zinc, which exist in forms of high iron and high indium. In order to recycle the valuable metal from these ores, the testwork of simultaneous leaching on neutral residue mixed with zinc concentrate of high iron and high indium has been conducted. The primary objectives are to leach the zinc and indium remaining in the neutral leach residue as ferrite using acid, and to reduce the ferric iron in solution to the ferrous by zinc concentrate, thereby extracting the zinc and indium in the zinc concentrate. The results indicated that in the following conditions, mass ratio of neutral residue to zinc concentrate of 1:0.25, particle size of 74-58 μm, initial sulfuric acid concentration of 150 g/L, liquid to solid ratio of 8 L/kg, temperature of 90°C, reaction time of 4h, the leaching efficiency of zinc and indium were over 95%, nearly 90% Fe was Ferrous in the leaching solution. This process effectively extracted zinc and indium and converted Fe3+ into Fe2+ in solution, and simplified the traditional process of reduction after leaching.

Jan 1, 2016