Search Documents

By Markus A. Reuter

In this paper various hybrid modelling architectures are proposed for the modelling and metallurgical control of pyrometallurgical reactors. Discussed are architectures in which data reconciliation is combined by thermochemical, neural net and dynamic modelling to improve the models. At the same time the data reconciliation models can act as soft-sensors for estimating unmeasurable data. Cases that are discussed are (i) the modelling of a submerged arc furnace for the production of thermal phosphorous, (ii) the processing of Sn-Pb-Zn flue dust (originating from secondary copper) in a hearth furnace, (iii) modelling of a steel converter, and (iv) dynamic modelling of a flash smelter.

Jan 1, 2001

By Tsembel Darjaa, Toru H. Okabe, Yoshiaki Umetsu

"With the purpose of extracting molybdenum and rhenium from molybdenum sulfide concentrate; .electrolysis of slurry, solvent extraction and ·precipitation operations were carried out. The slurry of the concentrate in 10 mass% NaCl aqueous solution was continuously circulated into a vertical type 10 stack bipolar electrolytic cell consisted of carbon electrode disks, and, the concentrate was dissolved by electrochemically generated oxidizers at 313 K. The current efficiency for molybdenum dissolution was 73 % after 10 hours electrolysis, and the leach solution was found to contain 0.2 mol/l of molybdenum and 4x10-5 mol/l rhenium. This result shows the dissolution is more than 8 times faster than that obtained using a single cell. The leach solution from electro-oxidation was then subjected to a solvent extraction for rhenium which is then recovered as sulfides. After rhenium separation, molybdenum was precipitated by pH adjustment, and solid MoO3 (H2O)x crystals, free of sulfate, were obtained from the leach solution containing large amount of so42-.IntroductionIn the past, electro-oxidation using a bipolar cell was applied for leaching molybdenite concentrate and ores at U. S. Bureau of Mines [1-3] and also at Bhabha Atomic Research Center [4]. In· these previous studies, Moebious type bipolar cells, in which electrode plates were vertically inserted into the free surface of the electrolyte, were employed and its effectiveness was demonstrated.Recently, the present authors studied on leaching of Mongolian molybdenite concentrate, and the effectiveness of leaching of the concentrate by electro-oxidation in alkaline and acidic NaCl solutions was demonstrated [5]. The leaching reaction during the process can be explained by the 18 electron transfer reaction of molybdenite (MoS2) with the oxidizers produced in-situ by electrolysis of NaCl aqueous solution. Further investigation was made with respect to various process parameters for electrooxidation such as pH, pulp density and temperature of the slurry, and the dissolution behavior of minor elements such as iron, copper, and rhenium [6]. Solubilities of molybdenum in the leach solution at, various temperatures and pH .was · studied, and feasibility of molybdenum recovery by hydrolysis of molybdenum species was demonstrated. By adjusting the pH of the leach solution, molybdenum oxides or hydroxides free from sulfate were successfully obtained from the solution containing large amount of sulfate ion. Rhenium present in the concentrate at a level of several tens of mass ppm was found to dissolve into the leach solution, and co-precipitate with the molybdenum compounds. Rhenium in the leach solutions, therefore, has to be recovered before precipitation of molybdenum, otherwise it is lost in the precipitate."

Jan 1, 2000

By K. J. Richards

The converting of copper mattes to blister copper has seen few technical advances since the introduction of batch furnaces using submerged tuyeres over a hundred years ago. The first side-blown converting vessel, operated by P. Manhes in 1882, was an offshoot of the 'Bessemer steelmaking process, and subsequent improvements in the conversion of molten mattes resulted In the Peirce-Smith converter, still the Industry standard today. While Peirce-Smith' converting has served the industry well since the early 1900!s, increasingly stringent environmental regulations, burgeoning energy costs, and a trend toward continuous processing have set the stage for a major improvement in this area of copper production. In contrast to a growing number of approaches for continuous converting using molten copper mattes, Kennecott is developing a process for treatment of solidified matte which allows improved' control, higher oxygen enrichment and a separation or decoupling of smelting and converting operations not possible with the other converting technologies. The new process known as Solid Matte Oxygen Converting, or SMOC, eliminates the need for molten matte transfers, minimizes fugitive emissions, and produces high strength SO2 off gases which substantially reduce offgas handling requirements. The SMOC process, despite additional matte solidification and size reduction steps, offers both capital and operating cost advantages for new smelters and the upgrading of existing plants, when compared with conventional converting technologies. Capital cost reductions of up to 35% in converting, gas handling, and sulfur fixation are indicated. Kennecott has successfully tested the new process concept and continued' development work is now under way to commercialize the technology. This paper reviews the limitations of batch copper converting with emphasis on the need for a continuous process, previous industry approaches to continuous converting of molten mattes, and the new Kennecott development.

Jan 1, 1983

By D. de la Villa

From 1989 to 1992 Rio Tinto Minera has developed and implemented a productivity program in its Huelva Plant, including Smelter, Acid Plant and Electrorefinery. This Plan was designed in order to increase productivity, reduce emissions and produce a better quality of cathodes. This paper describes investments and operating improvements involved in this project, focusing on Smelter and Acid Plants, and comments the results obtained so far.

Jan 1, 1993

By Timothy W. Ellis

"This paper presents the basic theory of operation, physical chemistry and phase equilibria which allow the development of liquid-liquid extraction circuits based on metallic solvents. The incorporation of reduction and reduction/diffusion processes into the process scheme is discussed and a detailed description of several liquid-liquid extraction schemes are developed. A synopsis of experimental results obtained using this method to separate rare earth and other metal based materials will be given.IntroductionConcerns over the effects of waste materials in the environment has been one of the significant social hallmarks of the late 20th century. Essentially every industrialized country has had to incorporate the cost of waste material into the equation of production. Legislative initiatives have led to the passing of very tough laws, by historical standards, which govern the environmental impact of materials processing.Liquid-Liquid extraction is a very common unit operation normally using aqueous and/or organic based solvents. Early work at the Ames Laboratory focused on the use of this technique for the reprocessing of spent fuel from liquid metal breeder reactors by the use of metallic solvents. Recently, we have revisited this area as a means to recycle/reprocess several emerging rare earth based materials, although this method has a much wider range of application. The reinvestigation of this technology is particularly timely as hydrometallurgical based processes are coming under increasing scrutiny in the U.S.A. by the Environmental Protection Agency (EPA). Although technology currently exists to remove contaminants from aqueous based waste streams, often the application of such methods is expensive. With proper design and judicious selection of reagents liquid metal extraction can achieve a high recovery along with a benign waste stream.This process has several possible advantages over other technologies. First is the elimination of aqueous solvents. Therefore, problems associated with disposal or reprocessing of the aqueous carrier are eliminated. Second, with proper system design, very high separation coefficients can be obtained thus limiting the number of stages required. Third, metals are extracted from metals with a metallic product, thereby eliminating the need to re-reduce metal for oxides or other compounds which are the common output for aqueous based extraction procedures."

Jan 1, 1996

By Steve Naruk

Microscopic point-count analyses, although time-consuming, provide detailed mineralogical information which is not obtainable by any other means. Such information can be invaluable for evaluating mill circuit behavior. In comparing two months of operation of a Cu-Pb-Zn sulfide flotation circuit, chemical analyses show that higher copper recoveries and concentrate grades were obtained from lower grade ore, but they provide no explanation of how the improvements were obtained. Quantitative micro-scopic analyses, on the other hand, show the following: 1. There was no change in the identity of the Cu-bearing minerals. 2. Increased copper recovery was achieved primarily by increased recovery of chalcopyrite middling particles. 3. The increased recovery of chalcopyrite middling particles also increased the amount of gangue entrained as locked particles. 4. Increased rejection of free gangue particles, particularly those finer than 25 microns in size, resulted in a net decrease in gangue content.

Jan 1, 1981

By Osamu Iida

Since 'start-up of the larger Mitsubishi Continuous Copper Smelting Process in 1991, furnace relining campaign was gradually prolonged to once every 2 years according to deregulation of governmental boiler inspection. On the other hand, in 1998 Naoshima smelter embarked on an intermediate strategic expansion plan to strengthell its international competitiveness. As part of this plan, modifications were implemented in the copper smelter designed to increase output of anodes from new charge source to 270,000 tpa. In May 1998, treatment of dried neutralized residue was started in C furnace, and during the shutdown for brick relining in April 1999, intensive modifications to the boilers as well as the installation of new spray coolers for furnace off gas treatment were implemented. Finally, the new larger oxygen plant was commenced its operation in May 2000 and the expansion was achieved around 30% increase of anode production from original design.

Jan 1, 2001

By Jacques Magnaudet, Julie Cranga, Didier Huin, Pascal Gardin

"With the aim of controlling steel grade in steelmaking reactors, IRSID and IMFT are developing a numerical description of the evolution of bubbles in the vicinity of a liquid steel/ slag interface. The objective is to identify the main parameters affecting the hydrodynamics of the various phases. The goals of the present paper are:• To describe the numerical technique developed to predict the multi phase flow including bubbles, liquid metal and slag layer.• To analyze the influence of the absolute pressure on the bursting of bubbles in a RH degasser. Validation is given by comparison with results available in the literature. The major point concerns the distinct behaviors observed whether the pressure is low or high.• To study the influence of the properties of the slag layer (thickness, viscosity and interfacial tension) on the entrainment of liquid metal in the wake of the bubble and on the nature of the projections from the bath surface.IntroductionMost of secondary steelmaking processes use gas stirring for homogenization, removal of nonmetallic inclusions or decarburization under reduced pressure. The bursting of gas bubbles at the metal or slag layer surface produces a beneficial ejection of metal droplets in the low pressure atmosphere, provided that there is no violent projection, which may have detrimental effects on the process.Our objective is to develop a numerical tool to study the phenomena occurring in the vicinity of the bath surface, in particular bubble bursting under reduced pressure and entrainment of metal in the slag layer. In this paper we report the first conclusions of our study. In the first section we describe the numerical model used to describe the three-phase flow and the expansion of the gas bubbles under the effect of the ferrostatic pressure. The second section is devoted to the study of pressure effects on bubble rise and bursting. The third section reports some computational results about the rise of a gas bubble through the interface between the two liquids."

Jan 1, 2001

By E. B. Zanelato

The process of casting metals and alloys occurs through the fusion of this metal and its subsequent casting into a mold with the dimensions and geometry close to the final piece. Most foundries use sand casting molds for making you. This work aims to characterize and evaluate the foundry sand to allow its use in segments of Civil Engineering, creating a viable destination for a residue is that discarded. The following characterization tests were performer: particle size, chemical analysis, X-ray Diffraction and Density Real grain. For the execution of the test specimens was used to 1:3 cement and sand, and the incorporation of 10% and 20% of the total mass replacing the sand, and the trace reference. The results show that best results in compression and bending tests were obtained by replacing 10 % of common sand for sand casting.

Jan 1, 2015

By Masami Taguchi

"It is found that lead monoxide, PbO, has an ionic conductivity, and the all solid-state electrochemical cell using this oxide as an electrolyte has attracted the attention of battery researchers. In this study, thin film PbO2/PbO/Pb solid cells were produced on glass substrates and their discharge properties were investigated. The acti.ve material for the positive electrode, PbO2, was obtained by reactive sputtering of a Pb target in oxygen plasma. The PbO electrolyte and the active material for the negative electrode, Pb, were vacuum evaporated from /3 -PbO powder and a Pb block, respectively. The open-circuit voltage of the cell agreed with the theoretical value based on the thermodynamic data, and the close-circuit voltage was improved by the addition of a univalent impurity such as sodium or potassium to the PbO electrolyte. The connection of the cells in series and in parallel produced a higher electromotive force and a larger capacity. Also, the charge-discharge cycling test revealed that the cell could be charged and function as a storage battery.IntroductionGenerally, the ionic conductivity of a solid-state electrolyte is lower than that of a liquid electrolyte near room temperature. This has been a serious obstacle to using such electrolytes in an electrochemical cell. However, some solid-state electrolytes, which can preferentially pass a specified ion and have high ionic conductivity, have been found. Lead monoxide, PbO, which is an oxygen ion conductor, is such an example (1)(2). If a solid-state electrolyte is adopted for use in an electrochemical cell the problem associated with a liquid electrolyte such as leakage can be alleviated. The cell structure also can be simplified, because the electrolyte plays the role of separator to prevent the active materials from mixing. Thus, physical vapor deposition technology may make it possible to develop a very thin film cell, which consists of only solid phases (3)(4). In this study, the thin film PbO2/PbO/Pb solid cell with a thickness· of only a few micrometers, in which all the constituents were systematically deposited on a glass substrate by reactive sputtering and vacuum evaporation, has been produced and the charge-discharge properties were investigated. An attempt was made to improve the discharge properties by doping impurities such as Na2CO3 and Sb2O3 into the PbO electrolyte. Moreover, the connection of the cells in series and in parallel to get a higher electromotive force and a larger capacity, and the charge-discharge cycling test to determine its use as a storage battery were carried out."

Jan 1, 2000

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

By Oleg Ostrovski

Industrial pyrometallurgical processes in ferrous metallurgy are based on carbothermal reduction of metal oxides. Carbothermal reduction of stable oxides requires high temperatures. Lowtemperature reduction can be implemented by using methane-containing gas with high carbon activity, or by carbothermal reduction under reduced CO partial pressure. Under standard conditions, methane is thermodynamically unstable above 550 °C and decomposes to solid carbon and hydrogen. At appropriate CH4/H2 ratio and temperature, carbon activity in the methane-containing gas phase can be well above unity relative to graphite, which provides favorable thermodynamic conditions for reduction. To maintain these conditions, the rate of reduction/carburisation should be higher than the rate of solid carbon deposition. The paper discusses reduction of pure manganese and chromium oxides at relatively low temperatures, and constraints in reduction of manganese and chromium ores. Reduction of metal oxides by carbon in hydrogen as an alternative use of natural gas is also discussed.

Jan 1, 2014

By Suzzann Nordwick

Over the past decade, significant advances have been made in the development of sulfate-reducing bacteria (SRB) technology to treat acid mine drainage (AMD). Bench-scale testing, field demonstrations, and engineered applications of SRBs for the treatment of AMD will be presented. Designs include an in situ bioreactor installed in the subsurface workings of the Lilly Orphan Boy Mine in 1994, the SRB bioreactors installed at the Calliope Mine from 1998 to 2001, the integrated biological reactors built at the Surething Mine in 2001, and the ongoing development of a replaceable cartridge system. SRB technology benefits include the reduction of dissolved metal ions to insoluble metal sulfides and the neutralization of the AMD resulting from the production of bicarbonate from the oxidation of organic nutrients. This paper will address engineering design criteria including the selection of organic media and system permeability and complete mitigation of AMD. Research was funded under Interagency Agreement No. DW899388-70-01-1 between the US EPA and the US DOE and was conducted by MSE Technology Applications, Inc., through the National Environmental Technology Laboratory (DOE Contract No. DE-AC22-96EW96405) at the Western Environmental Technology Office located in Butte, Montana.

Jan 1, 2003

By Jesse White, Tyler Salisbury

Research projects contain many stages of development from the conception of an idea to a fullscale commercial operation. The transition from laboratory-scale research to bench-scale roasting can represent a significant increase in complexity and cost, depending on how many variables are being evaluated. Thermogravimetric analysis (TGA) can simulate roasting conditions and produce a small sample for chemical analysis or materials characterization. A simultaneous thermogravimetric and differential scanning calorimetry (TG–DSC) can identify endothermic and exothermic reaction temperatures. Using thermal analysis, some of the process variables can be tested and eliminated such as ore and reagent blends, retention times, operating temperatures, and some atmospheres.

Jan 1, 2015

By Manju Gurung, Birendra Babu Adhikari, Keisuke Ohto, Hidetaka Kawakita, Katsutoshi Inoue, Shafiq Alam

Novel bio-adsorbent gel was prepared by immobilizing functional groups of glycidyltrimethyl ammonium chloride, a kind of quaternary ammonium chloride, onto polymer matrices of persimmon extract for the recovery of precious metals such as palladium(II) and platinum(IV) from chloride media. It was found that this adsorption gel exhibits high selectivity to gold(III), palladium(II) and platinum(IV) over base metals such as copper(II) and iron(III) while crude persimmon extract, the feed material, exhibits high selectivity only for gold(III). From the adsorption isotherms study, the maximum adsorption capacities for gold(III), palladium(II) and platinum(IV) were evaluated as 3.30, 1.67 and 1.00 mol/kg, respectively. Those for palladium(II) and platinum(IV) are higher than those of simple quaternary ammonium chloride type of chemically modified persimmon tannin gel and commercially available anion exchange resin.

Jan 1, 2016

By D. Morin

A general study of gold refractory arsenopyrite-pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 I unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery. Furthermore. the arsenite and ferrous produced in solution have to be oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimization study calculation for scaling-up the design and power requirements of an industrial installation. For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution. In that conditions the power cost is quite marginal. actually it is significant for the treatment of pure pyrite.

Jan 1, 1991

By S. Rick Gilbert

In the course of producing a final metal product, smelters, refineries, and other metallurgical facilities produce wastes which often come under the ?scrutiny of Federal and state regulatory agencies. Many of these wastes contain combinations on zinc, copper, lead, cadmium, nickel or other metals. Frequently in the form of reverts, dusts, or sludges, these metal-containing wastes are often buried in a landfill or speculatively accumulated for future action. Environmental liability can be reduced in many cases by selecting,-a recycling facility which can re-process the waste for.' metal recovery. Encycle, at its hydrometallurgical facility Corpus Christi, has Successfully processed a variety of metallurgical by-products and wastes and returned those contained metals to commerce.

Jan 1, 1995

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

By R. G. Haire

Studies of the f-elements under pressure provide important insights into their solid state chemistry and physics. From such studies, of the elements and their alloys, it has been established that the normally localized f- electrons of several of these elements can become, involved in bonding under pressure. The electronic behavior of f-element compounds under pressure tend to be more difficult to interpret, due to the variety and the nature of electronic orbitals that are present. The 4f-elements and some 60% of the 5f-elements have been studied under The systematic comparisons that have been established for these materials are discussed.

Jan 1, 1992

By Tseng. B. H.

Samples of unchlorinated and chlorinated carbonaceous concentrate from a carbonaceous gold ore were analyzed by transmission electron microscopy (TEM) for organically bonded sulfur and chlorine. The concentrate assayed 1.53 oz/t gold and 6.01% organic carbon. Much of the organic carbon occurred as sizable coarse particles up to several hundred microns in size, which showed no visible evidence of reaction with chlorine after chlorination treatment. Both the untreated and chlorinated fractions of the carbonaceous concentrate were analyzed by the TEM method, which detected organically bonded sulfur in all of the carbon particles examined in the untreated sample, ranging from about 1 to 5% organic sulfur, and averaging near 3.1%. TEM analysis of 40 carbon particles in the chlorinated sample indicated that organic sulfur was reduced significantly in the carbon and replaced in part by the chlorine, as the result of chlorination.

Jan 1, 1987