Search Documents

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By Leiv Kolbeinsen, Stian Seim, In-ho Jung

"The current work presents new experimental data in the iron-unsaturated region of the FeTiO3-Ti2O3-TiO2 slag system. The samples are prepared by melting pure reactants in a high frequency induction furnace that employs a cold crucible. A similar experimental set-up has been described in literature and proven suitable to investigate high titania slags. The FeO content of the samples range from 3.7 to 21.8 wt% and the Ti2O3 content range from 3.6 to 30.1 wt%. The liquidus temperatures of the samples are measured in-situ by a spectropyrometer and range from 1450 to 1645 °C.In addition, an improved thermodynamic database for the FeO-Ti2O3-TiO2 system has been developed. Ternary parameters have been included and optimized to fit previously published experimental data. This optimization minimizes the discrepancy between experimental data and thermodynamic calculations as previously discussed in literature. New liquidus projection plots are proposed for the FeO-Ti2O3-TiO2 and the FeTiO3-Ti2O3-TiO2 systems.IntroductionIlmenite (FeTiOs) smelting is a relatively small industry world-wide. However, a reasonable focus on the process has been applied in Norway due to the location of one such smelter in Tyssedal, which is located in the western part of Norway. The process is essentially carbothermal reduction, where most of the iron in the ilmenite is reduced to its metallic state, and the titanium oxide is concentrated in the slag product. The metallic iron is sold as a high purity pig iron and finds applications in cast products. The slag concentrate is further processed for the production of TiOvpigment and/or titanium metal. This further processing can be performed through different routes according to the purity of the slag concentrate."

Jan 1, 2012

By Charles I. Richman

Aquispirillum magnetotacticum (AM) is gram-negative hetrotrophic bacteria that belongs to a class ,of magnetotactic bacteria that have an ecological niche in marine marches and fresh water swamp sediments. Thiobacillus Ferrooxidans (TF) is a Gram-negative, acidophillic chemoliths that may have similar chemical conditions within the cytoplasmic membrane as Aquaspirillum M. to support growth of Magnetosomes. Magnetosomes are cellular bodies that accumulate under slightly aerobic conditions. Magnetotactic motion occurs in an external magnetic field and depends on the medium viscosity. The Atomic Force Microscope equipped with a magnetic tip shows the presence of Magnetosomes in these bacteria strains. The size, shape of magnetosomes in AM and TF strains are characterized.

Jan 1, 1998

By Guojun Ma

The entrainment of charge materials, evaporation or volatilization of elements and ejection of slag and metal by spitting or the bursting of gas bubbles are mechanisms whereby stainless steel plant dust are generated from the electric arc furnace and refining converter. TCLP and ASTM D 3987-85 tests on dust that was collected from the baghouse filter system of a South African Stainless Steel plant showed that this dust can be considered hazardous according to South African legislation, due to the high degree of Cr (VI) leachability (~13mg/l for TCLP and ~8mg/l for ASTM vs. regulation threshold of 0.05mg/l in drinking water). The dust is therefore considered to be harmful to both the environment and human health, due to its high solubility in water and carcinogenic properties. It should therefore be treated before being stockpiled or land filled. This paper consequently describes an investigation into the formation of Cr(VI)-containing stainless steel plant dust and the stabilisation thereof in a sintering process, whereby the dust was mixed with a silica-rich clay. It is postulated that Cr(VI) form when the (Mg,Fe,Mn,Cr)3O4spinel phase, CaO, Ca(OH)2 and CaF2 (all of which are present in the dust) react. This reaction was found to take place both at ambient and at high temperatures (1100°C). Stabilization of Cr(VI) in the dust could be achieved at an optimum sintering temperature of 1100°C for a 50mass% dust : 50mass% clay mixture. Chromium emission during the sintering process was found to be low, and within environmental limits.

Jan 1, 2006

By Zhanjun Wang, Yongqi Sun, Mei Zhang, Zuotai Zhang, Min Guo

The role of fluorine on the viscous and crystallization behavior of CaO-SiO2-MgO-Al2O3-FetO-P2O5-(CaF2) slags were explored using the rotating cylinder method, non-isothermal differential scanning calorimeter (DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. It was found that the viscosity slightly decreased with increasing CaF2 content. It was also found that CaF2 addition can promote the primary phase transformed from MgFe2O4 spinel to Ca3(PO4)F, which was beneficial to the enrichment of phosphorus. Additionally, the structure of the slags explained by X-ray photoelectron spectroscopy (XPS) and magic angular spinning nuclear magnetic resonance (MAS-NMR) were further analyzed, which was well in accordance with the above analysis.

Jan 1, 2016

By R. L. Nyirenda

The use of ammoniacal ammonium carbonate (AAC) leaching for the treatment of carbon steelmaking EAF dust has been investigated on a laboratory scale. The experiments have been conducted on dust samples obtained from three European steelmaking companies. As received, the dusts were found to be toxic when tested according to current EPA toxicity testing procedures. Toxicity was on account of the leachability of one or more of the following elements: Ag, Hg, Pb, and Cd. Leaching experiments with concentrated AAC solution at 40 " C showed that zinc oxide present in the three dust samples, 60-80% of the total contained zinc, was rapidly solubilized. Data on the dissolution characteristics of Cd, Fe, Pb, Mg, and Mn are also presented. Toxicity tests conducted on residues of the leaching experiments found these to have leachates below past and current EPA toxicity threshold limits.

Jan 1, 1993

By M. M. Salari Rad

An investigation of gold distribution in the mill products of Sar Cheshmeh beneficiation plant demonstrates that on average 44% of the gold is routinely recovered as a by-product in the copper concentrate, and the remaining is lost to the tailing. In order to evaluate the causes of gold losses, the distribution and mode of gold occurrence in the Sar Cheshmeh ore and mill products were studied. Searching for gold within samples and within individual grains of sulphide minerals was carried out by SEM in the backscattered electron mode and SIMS, respectively. The mineralogical distribution of gold revealed by microbeam techniques were combined with the results of relevant metallurgical experiments including, sizing, heavy liquid separation, and diagnostic leaching tests, and the nature and location of gold in the ore and mill products were determined. The combined results of the experimental approaches pursued suggest that while there are some gold in solid solution and/or -colloidal size within sulphides of the Sar Cheshmeh ores, "visible" gold is the principal form of gold occurrence at Sar Cheshmeh.

Jan 1, 1999

By Jinxing Ji

The thiosulfate lixiviant system for leaching of gold has been under extensive investigation for nearly two decades and consists of ammonium thiosulfate, copper and ammonia. There are several challenges with this system. The occurrence of ammonia must be taken into account from a health and hygiene aspect in the workplace, and also from an environmental perspective with significant levels of ammonia and copper in the tailings. Copper accelerates the leaching rate but causes excessive thiosulfate degradation. A new lixiviant system that has been investigated consists only of sodium thiosulfate without copper and ammonia. Gold leaching is carried out in an enclosed reactor with slightly elevated oxygen overpressure and temperature. Extensive leaching experiments were carried out to minimize thiosulfate degradation and polythionate formation while maximizing the gold extraction. For the preg-robbing carbonaceous ore sample tested, gold leaching was essentially complete within six hours and the thiosulfate consumption was lower than in the typical ammoniacal thiosulfate system. The gold thiosulfate complex in the pregnant leach solution was found to be quite stable under ambient conditions. This new leaching system has the advantages of being more environmentally friendly, has a shorter residence time, lower thiosulfate consumption, lower oxygen consumption, and is easier to control.

Jan 1, 2003

By K. Koike, N. Masuko, Y. Takasaki

At the Zinc & Lead'95 symposium, one of the authors presented several modifications of Pb-Ag-Ca alloy anodes for the zinc electrowinning process, and also, the behavior of some organic additives in the electrolyte. In this study, the mechanical properties of the electrode materials composed by Pb-0.5 wt% Ag-(0~0.8) wt% Ca were studied by the tensile and Vickers hardness methods. Furthermore, experimental research on the influence of rolling and annealing treatments on the electrolytic behavior and mechanical properties of these alloys was carried out. The tensile strengths of the annealed Pb-0.5 wt% Ag-(0.1-0.8) wt% Ca alloys were the same or higher than those of the as-cast Pb-0.9 wt% Ag alloy. The anode potential using the as-cast Pb-0.5 wt% Ag-0.6 wt% Ca alloy decreased compared to the as-cast Pb-0.9 wt% Ag alloy. Moreover, the annealed Pb-0.5 wt% Ag - 0.6 wt% Ca anode after rolling showed a lower anode potential than the as-cast Pb-0.5 wt% Ag - 0.6 wt% Ca anode.

Jan 1, 2000

By Abhishek Lahiri, Animesh Jha

"A new technique for the selective separation of rare earths and impurities from lower grade titaniferous ores has been developed which will reduce the overall reduction in the energy costs, and therefore the CO2 generation by at least an order of magnitude during the chlorination and waste handling stages of TiO2 to TiCl4 reaction. The process includes roasting the ilmenite ore with alkali followed by water washing step, which removes nearly 80% of oxides of lanthanide and actinide elements present in lower grades of titaniferous minerals. In the context of preferential separation of rare- 3+ + earth and actinide oxides, we have examined the roles of Al and K ions on the lattice structures of ilmenite and complex titanate as the product layer forms during the roasting in air in the presence of potash. The composition of the mixtures of oxides derived from the separation process shows that the mixture of rare-earth oxides m ay be a high-value co-product of the overall beneficiation process.IntroductionWorldwide the production of synthetic rutile is carried out either by the sulphate or the slag-making followed by fluidised bed chlorination of TiO2 enriched slag granules. The chlorinated gas is then re-oxidized to make white pigment grade TiO2. The waste generated by the sulphate process is predominantly iron sulphate, which has limited use in the water treatment plant. The remaining wastes from the sulphate process undergo further treatment using filtration followed by evaporation and thermal decomposition after which it is disposed into deep sea. On the other hand the chloride waste is extremely hazardous and requires special case by neutralisation, followed by impoundment in a managed pond, where it is monitored for long-term for potential contamination to the soil and ground water. Rare-earth and prelanthanide wastes often end up in the pond where they are diluted and irretrievably lost for further use or recycle. Certain parts of the world the chloride process wastes are pumped via deep boreholes into porous geological strata. The present techniques of disposal are not only expensive but also pose continued threat groundwater and soil and marine life in case of sulphate waste [1, 2]."

Jan 1, 2009

By Alexander I. Raitchenko

"An electroconductive viscous liquid may flow in laminar or turbulent regime under Lorentz-force generated by the intercrossed electric current and magnetic field. When there is a starting flat layer between hard and free boundaries with surface tension the spatial Lorentz-force can create a specific stationary regime of flow: the plane free surface will transform into the wavy one, and the movement in the depth will be not laminar and not turbulent, but this regime will be characterized by organized forms with indications of ""rolling of long cylindrical drops"". Wave-length is determined by the viscosity, the density, the surface tension, the average thickness of layer, and Lorentz-force. ·The limit of wavy regime is determined by most long of wave which is directly proportional to the critical value of specific flow and inversely proportional to the kinetic viscosity. The proper critical value of Reynolds number is determined by the dimensionless combination containing surface tension, density, viscosity, and Lorentz-force. The mentioned dimensio.nless combination in our case is some criterion substituting the known Kapitsa number for case of the thin viscous liquid layers under gravity. Spreading of admixture by mechanism of wavy regime is more rapid than by common diffusion or by laminar flow. The suggested conception can be a contribution into the theoretical basis for elaboration of some specific liquid metals technologies."

Jan 1, 1999

By Xi Dai

The LiFe1-xNixPO4(x=0, 0.05, 0.10) cathode materials for Li-ion battery were synthesized with Fe1xNixC2O4?2H2O(x=0, 0.05, 0.10) as Fe sources by high temperature solid-state reaction method. The Fe1xNixC2O4?2H2O(x=0, 0.05, 0.10) materials were produced by liquid co-precipitation method and crystal structure and morphology of cathode materials were characterized by X-ray diffraction and scanning electron microscopy. The composition contents and charge-discharge performances were measured by chemistry analysis and charge-discharge apparatus. The XRD patterns showed that LiFe1-xNixPO4(x=0, 0.05, 0.10) cathode material samples were well-crystallized homogeneous olivine-type phase, with only tiny trivalent iron impurities according to chemistry analysis results. Charge-discharge test showed that cathode materials possessed excellent charge/discharge capacities, about 150mAh/g at 0.1C rate and more than 120mAh/g at 0.4C rate. The polarization of cathode in charge-discharge process can be restrained effectively, for the potential offset between oxidative peak and reductive peak of doped LiFePO4 material was only 0.079V, lower than pure LiFePO4 markedly.

Jan 1, 2006

By M. Urda-Kiel

Stainless steel is increasingly used as a cathode starting sheet. It was shown earlier that even when depositing copper on copper, a substrate-influenced zone appears in the deposit structure, followed by a transition zone and finally by the electrolysis-influenced structure. On copper, the substrate-influenced zone has a thickness of twenty micrometers and on titanium, eventually more than fifty micrometers. Initial nucleation and growth have a considerable influence. In this paper, copper was deposited in a channel cell on four different 304 stainless steel substrates: mechanically polished and anodized, respectively, at 0, +400 and +800 mV/SHE in 1M H2SO4 at 20°C. Copper was deposited under electrowinning conditions after solvent extraction (SX) (40 g/l Cu++, 180 gh/l, H2SO4, 20 or 60°C). The results showed that, although Auger surface analyses of the substrates were only slightly different one from another including the oxide thickness, nucleation and initial stages of growth were very sensitive to the surface treatment of the substrate. Potential step and current step methods gave similar results : progressive nucleation followed by 3D diffusion controlled growth. The highest nucleation frequency was observed on stainless steel anodized at 0 mV/SHE, under various electrolysis conditions. The potential influence of these findings on industrial practice is discussed.

Jan 1, 1999

By Cristiän Vargas, Jaime Simpson, Gerardo Cifuentes

"This paper presents a new process for the precipitation of Sb and Bi present in copper refinery electrolytes in the presence of Pb02 (Chilean Patent No. 45,037). To establish the conditions under which the precipitating compounds form, it was necessary to evaluate the amount of PbCh consumed, antimony extraction efficiency, precipitate stability, reaction kinetics, diffraction analysis and X-ray fluorescence, separation of size, plus observation of the precipitates in the electron microscope. Preliminary tests were carried with synthetic copper refinery electrolyte, and then the final testing was done with electrolytes from Chilean refineries. This process provides a real alternative for the treatment of copper refinery electrolytes for the control of Sb and Bi in solution; it is very simple to operate and is low cost compared with competing processes.Introduction.A high quality copper cathode implies a cathode free of impurities. The electrorefining process seeks to eliminate these impurities from the copper anode (99.5% purity) by its dissolution in an acid electrolyte using chemical and electrochemical reactions. As a result of this process, a cathode (99.99% purity) is obtained. If the concentration of impurities in the electrolyte, from the dissolved anodes, begins to increase; particularly if the antimony concentration in the electrolyte increases up 500 ppm, the formation of floating slimes which are a major cause of contamination of the cathode is favoured. The most important impurities from the point of view of their effect on the quality of the cathode copper, are Ag, As, Sb, Bi, Pb, Se and Te. Silver is necessary for the control of Se and Te. To control all of these impurities, it is necessary to establish different methods or parameters of control in copper electrorefining. These parameters are anode composition, additives, purification of the electrolyte, current density, acidity, etc."

Jan 1, 2012

By Jin Liu

To improve value metals recovery, a new operating concept for the Inco flash furnace was investigated, in which the flash furnace coke addition practice would aim at establishing a reducing barrier on the surface of the molten bath. The descending partially oxidized sulfide mineral particles would reach the supernatant coke layer prior to the formation of slag. The key for success depends on the effectiveness of the coke layer to produce a sulfur deficient matte while maintaining furnace production capacity. The mechanism and rate of carbon reduction of the phases formed in the flash flame, i.e. sulfide (matte) and oxysulfide was investigated by means of crucible graphite reduction test work. The objective of these tests was to measure the rate of solid graphite reduction of matte, oxysulfide, slag, and matte+slag mixture at different temperatures. These tests were expected to permit understanding and explaining the reduction mechanism of each material by comparing the respective reaction rates, product reaction gas compositions, reduced material assays, and other relevant parameters. Direct visual inspection of the test crucibles would provide additional information.

Jan 1, 2006

By Ho Jung Heo

The proper control of slag composition is a dominant factor affecting yield of iron as well as dephosphorization efficiency in an electric arc furnace (EAF) operation. Moreover, thermophysical properties of slags such as viscosity are strongly affected by the changes in slag composition. Slag foaming, which is also a function of viscosity, is directly connected with the yield of iron and thus optimum slag chemistry are highly required in view of thermodynamics and physical properties. Therefore, we analyzed the slag composition in commercial melt shop (70 ton EAF) with the aim of higher yield of iron as well as higher dephosphorization during EAF process.

By Florian Kongoli

The so-called "fayalite" slag, despite problems associated with it, is the most widely used slag in copper smelting processes. Thirty years ago, in order to overcomes some drawbacks of this slag a new "calcium ferrite" slag was proposed especially for continuous copper converting. Since both slags have strong and weak points depending on the field of their application about 8 years ago another new "ferrous calcium silicate" slag was proposed that is expected to solve the drawbacks of each slag. This new slag is defined as mainly consisting of FeOx, CaO and SiO2 as its main components but it can practically have several combinations of these constituents. In order to determine the best area of this slag for possible industrial application the quantification of phase relations is an important subject. In this paper the work carried out by the authors in quantifying through an original physical model the phase relations, liquidus surface, liquidus regions, behavior of solid phases and the effect of minor components is reviewed. Several special compositions of this slag have been identified and discussed for possible applications in the industrial practice.

Jan 1, 2006

By F. Tanaka

In April 1999, a two-year campaign of the Mitsubishi furnaces was achieved at Naoshima Smelter; the present one is expected to be extended much longer. An overview of basic technology for decreasing refractory wear in the Mitsubishi Process is presented. One of the main features of the process is the use of top blowing lance technology which has a different effect on the furnace refractory than other conventional processes. The refractory wear of concern is hearth wear caused by top blown powder injection, wear of the side wall caused by splashing droplets, and wear of the bath level refractories caused by surface waves of melts in the furnace. These have been systematically investigated for many years. This paper describes the results of various model tests and their application to practical furnace design and operation.

Jan 1, 1999

By Alexander A. Knminskii

Polymorphism of BaR2F8 compounds is analyzed, and some peculiarities of obtaining monoclinic low-temperature (3-BaR2F8 crystals (R=Y, Ho-Yb) and orthorhombic high¬temperature a-ßaR2F8 crystals (R=Yb, Lu) by the Bridgman-Stockbarger growth technique are discussed. We pay a special attention to BaYb2F8:Er3+ crystals, which are able to generate both 2:µm SE using the new four-level operating scheme (4F9/2?4I11/2 laser channel) and 2- and 3-µm SE by means of the cascade scheme (4F92?+4I11/2?+4I31/2). This 2-µm generation of Er3+ ions has an advantage over similar SE of Ho3+ and Tm3+ ions (especially under diode laser pumping), that is important in designing the medicine and ecology laser. We report on orthorhombic BaR2F8 crystals with the ordered structure, a new crystalline materials for generating Ln3+ ions. The growth conditions are determined and orthorhombic BaLu2F8 crystals of several cm3 in volume doped with Ce3+, Nd3+, Ho3+, Er3+, and Tm3+ ions are obtained for the first time. Spectroscopic and laser characteristics of these crystals are discussed for Nd3+-and Era+-doped samples serving as representative examples. In particular, low-threshold stimulated emission was excited in 4F3/2?+4I11/2 channel of Nd3+ ions in the BaLu2F8. Room-temperature generation was obtained also at -1.317 µm wavelength for Nd3+ and at ~2.8 µm (several lines) for Era+ ions in this new laser crystalline host with a threshold of about 20 J.

Jan 1, 1997

By Asok Kumar Das

"In steel making ferroalloys occupies a commanding role for production of varied quality of steel. Ferroalloys enable alloying elements such as chromium, silicon, manganese, vanadium etc to be safely and economically introduced into metallurgical processes thus giving certain desirable properties of the alloyed metal. Their importance grew with the progress of the steel metallurgy which implied more diversified alloying elements, in better controlled quantities, in purer steel. The ferroalloy industry became a key supplier to the steel industry. Production of ferroalloys generally involves the use of Electric Arc furnace(EAF) into which raw materials(e.g. various metal ores, quartz, coke, lime etc ) with relatively fluctuating physical compositions are loaded. Due to this, one of the major environmental impacts of producing ferroalloys is the emission of dust and fume from the smelting process. INTRODUCTIONFerro Alloys are essential ingredients used for refining, de-oxidation, desulphurization and alloying addition in the production of different types of steel and hence Ferro Alloy industry forms a back bone of iron and steel in the world. Indian ferro alloy industry is more than 45 years old. It produces most of the bulk ferro alloys and a large number of special ferro alloys. The present installed capacity of the Indian ferro alloy industry is sufficient to meet the requirement of existing level of indigenous steel production of about 46 million tonnes. Revised National Steel Policy – 2008 envisages production of more than 100 million tonnes of steel by the year 2011-12, at proportionate annual growth rate per annum. The focus of the policy is to achieve global competitiveness not only in terms of cost, quality and product-mix but also in terms of global benchmarks of efficiency and productivity. In order to achieve the objectives of National Steel Policy and also to meet the requirement of ferro alloys, the Indian Ferro Alloy Industry has to gear up in terms of enhancement in production capacity, sourcing of raw materials, up gradation of technology, improvement in productivity, automation / mechanization, customer satisfaction etc."

Jan 1, 2008