Search Documents

By Kenshi Kawabata, Mitsuji Ueda, Junko Umeda, Katsuyoshi Kondoh, Kantarou Kaneko

Solid-state recycling process of in-house scraps of machined magnesium (Mg) alloy wastes has been established to directly produce wrought materials via the repetitively plastic deformation by Roll-compaction (RCP) and the conventional hot extrusion. The coarse chips, wasted in machining AMX602 (Mg-6Al-0.2Mn-2Ca) cast billets used for the gate bar used in Electronic Toll Collection (ETC) of the high-way system, were employed as the input materials in this study. RCP process enabled to serve coarse Mg alloy powder consisting of refined grains and intermetallics with no re-melting. They were easily consolidated by hot extrusion, and their wrought alloys showed both homogeneously refined grains less than 1~2 µm by dynamic recrystallization and randomized texture by repetitive plastic deformation on the input wastes. These materials revealed extremely advanced mechanical properties of high tensile strength of 356MPa and high ductility of 14.8%, compared to the originally virgin materials with 270MPa TS and 5% elongation. When applying the same Mg alloy wastes via RCP process to the mass production in the company, the large-scale extruded materials also indicated the superior tensile properties. It means that this direct solid-state process is held as “Up-grade recycle of metal wastes”.

Jan 1, 2008

By Baozhong Zhao

In-situ vitrification (ISV) is a new technology used for treating radioactive, organic and inorganic contaminated soils. In this process, electricity is applied through electrodes buried in the contaminated soil to melt it and form an environmentally stable glass-like solid. The organic contaminants and volatile metals are vaporized during heating up, the non-volatile inorganic elements are dissolved and incorporated into the melt. In present full-scale operation, the ISV process can treat 4 to 6 tons of soil per hour at consumption of about 1000 kwh per ton of soil. In this study, various configurations of electrodes were examined in a mathematical model. The results may be used to optimize the ISV process.

Jan 1, 1994

By E. S. Geskin, W. L. Chen, A. Vora

"This paper is concerned with the application of an abrasive waterjet for metal shaping. The waterjet cutting technology uses water compressed to the pressure up to 55,000 psia which is accelerated in a cylindric nozzle. Abrasive particles are then supplied into the water stream and accelerated by the water. Cutting occurs via the interaction between the water-particles stream and a workpiece that causes material erosion at the impingement zone. The mechanism of this interaction enables shaping of practically any material with a minimal effect on the metallurgy of subsurface. The motion of the jet penetrating through a material body is guided by a robotic arm. A waterjet cutter is becoming one of the principal tools for shaping titanium, super-alloys and other hard-to-machine metals and composites. The shaping, resulting from the waterjet cutter, is very similar to laser beam cutting. However, unlike laser processing, there is no damage to the subsurface structure.The presented work discusses the experimental study of cutting of titanium plates. The results of these experiments demonstrate the potential of the abrasive waterjet as a shaping tool. IntroductionOne of the main avenues in the development of metal shaping is the use of high energy beams as cutting tools (1,2). There are a number of advanced beam oriented material removal technologies, such as laser, electron beam, plasma and abrasive waterjet (AWJ) cutting. The advantages of AWJ cutting are well understood and documented (3-14). This technology has the potential of becoming the principal tool for netshaping and netsurfacing of parts. However, the use of AWJ is currently limited to cutting of hard-to-machine materials such as titanium, superalloys, glass, composites, etc. The cost of A W J cutting is much higher and the productivity is much lower than those of the thermal cutting. At the same time abrasive waterjet can be used for shaping any existing technological material from fabrics, plastics, aluminum to glass, composites, and diamonds. The material losses during AWJ shaping are minimal. The roughness and waveness of the surfaces generated during AWJ cutting are substantially less than those of the thermal cutting. Due to the size of the jet cross-section total force exerted by the jet on a workpiece does not exceed 30-50 newtons. This terminates the need in the use of complex fixture for material holding. Low applied forces and low surface temperature prevent the damage of metal subsurface in the course of cutting. The small size of the impingement area will determine the limited width of the kerf. Due to the size of kerf and unidirectional character of the water jet the formation of practically any metal contour is possible."

Jan 1, 1988

By Patricio Barrios

In February 1996, ATLANTIC, COPPER completed the construction of a Project for Expansion and Environmental Improvements in its Smelter and Electrolytic Refinery located in Huelva. Following the expansion, the new operating concept is based on the simultaneous blowing of two converters, while increasing throughput in the Flash Furnace up to the level required to deliver matte to both converters. While the production level planned with the Project.(270,000 MTPY of copper from concentrates) was reached the following June, work since then has been carried out to optimize the new equipment .and to develop a new operating shedule. This paper describes operational experiences from the start up of the Expansion Project, difficulties encountered and operating improvements introduced, which have allow an increase of production levels up to 300,000 MTPY of copper.

Jan 1, 1998

By V. M. Paretsky

Recent developments made in the Gintsvetmet Institute in the field of autogenous smelting processes have confirmed that autogenous smelting continues to be the main prospective technology for pyrometallurgical processing of sulfide raw materials. This technology ensures energy conservation and environmental safety conforming to the current world standards for production of heavy non-ferrous metals. Two alternative processes of single-stage autogenous smelting producing white metal as well as high-basic ferrite-calcium slags have been developed and can be recommended for technical modernization of Russian copper smelters.

Jan 1, 2002

By Guozhu Ye

Hydrometallurgical zinc recovery from EAF dust has several advantages compared to pyrometallurgical alternatives in terms of low temperature operation, lower energy consumption and higher flexibility. Many hydrometallurgical processes have been suggested and tested over the years without success. The main reasons are: -Low leaching yield of zinc due to the fact that a high fraction of ZnO in the EAF dust exists in the zinc ferrite structure which makes selective leaching of ZnO not possible -Many of the proposals could not handle the halide in the EAF dust To eliminate these two disadvantages, two zinc ferrite elimination concepts have been tested and developed in the REZIN project of the EU 5th Framework Programme. The two concepts for zinc ferrite elimination could be shortly described by the following chemical reactions: A. ZnOFe2O3 + 2CaO = Ca2Fe2O5 + ZnOfree B. ZnOFe2O3 + C = Femet + CO/CO2 + ZnOfree These two concepts were investigated in details in combination with a subsequent leaching step using the novel EZINC process for recovery of zinc from EAF dust. Leaching of pretreated samples has shown great increases of a zinc recovery yield. A zinc recovery of over 90 % could be reached, as compared to about 50 % for no-pretreated samples. This paper will describe the two concepts in details.

Jan 1, 2006

By B. Q. Li, H. C. de Groh, X. Lu

"A fully 3-D, transient finite element model is developed to represent the magnetic damping effects on complex fluid flow, heat transfer and electromagnetic field distributions in a metallic melt. The model development is based on our in-house finite element code for the fluid flow, heat transfer and electromagnetic field calculations. The numerical model is tested against numerical and experimental results for water as reported in literature. Various numerical simulations are carried out for the melt convection and temperature distribution with and without the presence of a transverse magnetic field. Numerical results show that magnetic damping can be effectively applied to stabilize melt flow, reduce turbulence and flow levels in the melt and over a certain threshold value a higher magnetic field resulted in a greater reduction in velocity. Also, for the study of melt flow instability, a long enough running time is needed to ensure the final fluid flow recirculation pattern. Moreover, numerical results suggest that there seems to exist a threshold value of applied magnetic field, above which magnetic damping becomes possible and below which the convection in the melt is actually enhanced.1. INTRODUCTIONThe imposition of a DC magnetic field on a moving, electrically conducting fluid, such as molten metal or semiconductor melt, produces an opposing Lorentz force that results in a reduction of flow velocity in the liquid. This effect has been explored in both the semiconductor and metals industries to control natural convection and/or surface tension induced Marangoni convection as well as thermally induced flow instability during solidification processing of these melts [1-6]. A mathematical model can be of great use in developing both fundamental understanding of the fluid-magnetic field interactions in these magnetically-assisted processing systems and basic guidelines for process design, control and optimization.This paper presents a 3-D mathematical model for magnetically damped fluid flow and heat transfer in a melt cavity, which is useful for interpreting results for unidirectional solidification processes at slow solidification rate, and some preliminary results concerning the magnetic damping effects on the flow instability in the melt. The model development is based on the finite element solution of the Navier-Stokes equations, energy equations and equations for induced electric field. The model is tested against reported results and is then applied to study the fluid flow and thermal distribution in the metallic melt with and without an external magnetic field."

Jan 1, 1999

By Zhang Jianliang, Xu, Zuo, Runsheng, Haibin, Kexin, Jiao

Full oxygen blast furnace iron-making is one of the new technologies, which is most likely to realize large-scale application. In this paper, based on the technology of full oxygen blast furnace, the reduction behavior of pellets is studied systematically by using the analytic method of non-isothermal dynamics on the different atmosphere(CO,H2) and the dynamics model of gas-solid reduction reaction is constructed, which lay the foundation of reduction model establishment of full oxygen blast furnace burden. The result shows that the time of pellets which began to react is delayed with the increase of the content of H2. When the temperature is between 650 'C and 1050 'C, the content of H2 in the reduction atmosphere is larger, and the rate of the reduction pellets is larger. The reduction rate changes at 780 'C, and a certain amount of H2 in the reducing atmosphere will significantly improve the reduction reaction when the temperature is above 780 'C. Non-isothermal reduction behavior is controlled by interfacial chemical reaction and internal diffusion under high reduction potential. H2 ratio in reducing atmosphere increased from 0% to 100%. The reduction reaction of the apparent activation energy decreased from 49.03kJ-mor1 to 33.74kJ·mor1.

Jan 1, 2013

By John K. Wright

The segregation process involves heating oxide-type ores with a halide salt in the presence of a solid reductant. By a complex series of cyclic vapour-phase reactions, the desired metal is extracted from its original position in the ore and segregated to the vicinity of the reductant. In this form it is then amenable to concentration by physical methods. In this work the segregation behaviour or eight different nickel laterite ores has been examined using a laboratory rotary kiln. It was found that the silicate (serpentine) ores responded better to the segregation conditions used than did the limonitic ores. An examination of the segregated metal particles showed that they consisted of ferro-nickel. The concentration of nickel in the metallics was sensitive to the ore types and the segregation roasting conditions.

Jan 1, 1994

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By Neil E. Izatt, Ronald L. Bruening, Steven R. Izatt

"IBC has developed environmentally friendly Molecular Recognition Technology (MRT) processes to selectively extract, recover, and purify a wide range of metals from a variety of process streams. The incorporation of MRT into process flow sheets can improve the economics of the processes. MRT separations are effective even at low (mg/L to \i%JV) metal levels. MRT processes are sustainable, being economically viable, energy efficient, and environmentally friendly as well as having a low carbon footprint. Examples of MRT processes will be presented and discussed involving platinum group metals, gold, rhenium, and other metals of interest to the mining community.IntroductionA significant portion of the earth's precious metal resources has been moved during the past century from underground to above ground [1]. This movement has important economic, health, environmental, ecological, and sustainability implications for the earth and its population. There is concern that recycling of certain precious and specialty metals from end-of-life (EOL) electronic wastes (e-wastes), catalyst wastes, mining waste streams, and other waste products such as rechargeable batteries is not adequate to maintain supplies of these metals sufficient for future needs [2-4]. Improved metal recycling rates and more efficient metal recovery from the enumerated wastes would significantly reduce the amount of virgin metals that must be mined to support our lifestyle [5]. More efficient separation procedures in ore processing flow sheets and more effective recovery of metals from low-grade waste streams would reduce metal loss in the mining industry."

Jan 1, 2012

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By Lucas Lopes da Costa

Bamboo fibers were characterized in terms of diameter distribution and tensile properties. Polyester matrix composites reinforced with these fibers were investigated for their flexural mechanical behavior. Specimens with up to 30% in volume of continuous and aligned bamboo fiber composites were bend-tested until fracture. The results showed an improvement in the composite strength and stiffness with the amount of bamboo fiber. A microstructure analysis by scanning electron microscopy revealed a reasonable adhesion between the fiber and the polyester matrix which justifies the improved mechanical properties of the composites.

Jan 1, 2010

By Khosrow Nikkhah

Increasingly ion exchange systems are being included in design of hydrometallurgical plants for metal extraction or impurity removal. Because such systems operate sequentially and are based on resins that exchange one ion for another, store it temporarily and release it to a regenerating solution, the usual steady state heat and mass balancing tools and spreadsheets cannot be used to design them successfully. This paper outlines the role of dynamic simulation in design of ion exchange systems. Examples are given for use of dynamic simulation in design and investigation of equipment based on consideration of the effect of input criteria such as expected ion loading and elution profiles. The methodology for dynamic modeling using IDEAS in design of multi column ion exchange trains operating in parallel is presented. Results shown include the non-steady state distribution of extracted metal and limitations imposed on operating conditions. These conditions include proposed sequencing of columns for loading and elution cycles, loading, elution and recycle flow rates as well as size and choice of related ion exchange plant equipment.

Jan 1, 2003

By D. Valic

In 1997, 9.2 million tonnes of mined, recoverable copper was produced, of which, 1.8 million tonnes or 19.4% was produced by leaching, solvent extraction and electrowinning. The amount of copper produced by this method grew faster than those attained from concentrate smelting, signifying the growing importance of this low-cost production method. Statistical experimental design, unlike traditional approaches, allows for proper distribution of experiments within the boundaries of factors being studied such that the number of experiments required to develop a sound relationship between the factors and a response is minimized. In the past, very little use has been made of statistical experimental design in copper electrowinning studies. Traditional one- variable-at-a-time approaches are widely employed for this purpose. The present study employs a factorial experimental design to relate current efficiency with current density (180 and 300 A/m2), copper concentration (25 and 65 gL), and temperature (40 and 60 °C). Pure synthetic electrolyte with a constant acid concentration of 180 g/L was used throughout the study. The designed study produced a linear relationship where the independent variables of current density, copper concentration, and temperature, and their interactions, were found statistically significant. It was shown that current efficiency could not solely be used as a predictor of copper cathode quality. The quality of the deposit is difficult to be incorporated into a model or relation. It was determined that other measures, such as cathode morphology and crystal structure should be considered. This was done through XRD and SEM analysis.

Jan 1, 1999

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By D. M. Jones

In May 1999 the first campaign of the BHP San Manuel flash smelting furnace (FSF) will be concluded after having set world records for both campaign length and tonnage smelted for an Outokumpu copper flash smelting furnace. This paper reviews planned process and equipment modifications including: The installation of a new 36,000 mt concentrate storage facility; replacement of the existing dryer electrostatic precipitator with a baghouse; modification of the FSF dry charge bin and feed system to achieve mass flow and uniform feed to the concentrate burner; modifications to the FSF and its ancillary cooling systems; modifications to the waste heat boiler and offgas handling system to increase gas handling capacity and improve process efficiency;- and improvements to the FSF fugitive gas collection system. A brief review of the planning and execution of the scheduled 45 day shutdown is also given.

Jan 1, 1999

By Daniel Kim, Ari Rantala

Efficient on-line monitoring of electrolytic cell performance in copper electro-refining has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Based on Kennecott Utah Copper's innovation Outotec has developed a novel and innovative electrolytic cell monitoring system called CellSense™ System. As the system is based on self-powering from bus bars, wireless communication, on-line adaptive modeling and easy to access information and alarming, traditional obstacles of electrolytic cell monitoring are eliminated. With cell voltage and electrolyte temperature measurements, CellSense System enables real-time cell performance discovery and early reaction to critical production or quality disturbances such as short-circuiting, flow blockages, cold cathodes or electrolyte temperature excursions. During the past few years the system has been delivered to over 3500 commercial cells. In this paper the largest CellSense™ System ever delivered and recently adapted by Kennecott Utah Copper with 1412 cells monitored on-line for high tankhouse performance, cathode quality and optimized operator work flow is presented. Early results and benefits are discussed.

Jan 1, 2012

By Joel K. Witt

San Manuel Oxide operations of BHP Copper, located in Southeastern Arizona, operates a leach-solvent extraction/electrowinning (SXEW) facility that produces high quality cathode copper from low-grade oxide ores. Permanent heap leaching and in-situ leaching methods accomplish the dissolution of copper from the oxide ores. Open pit mining and heap leach construction took place from 1985 to 1995. Run-of-mine oxide ore from the pit was hauled to the heap dumps and leached by the soaking cure and continuous irrigation method. Solution application to the heaps still continues and acid soluble copper recovery has reached 86%. This paper presents and discusses the current operating practices and innovations applied to the leach facilities to maximize copper recovery from the heap leached residue. Factors such as irrigation methods, solution chemistry, sideslope treatment, post curing, lixiviant acid strength, and "rice paddies" irrigation, will be discussed. Heap leach solution control and sampling methodologies will be also presented.

Jan 1, 1999