Search Documents

By Y. Ono

In lightweight metal processing such as aluminum (AI) and magnesium (Mg), metal cleanliness is a crucial process parameter for refining, part manufacturing and recycling in order to obtain high quality parts and products. In this paper, techniques for cleanliness evaluation of molten AI and Mg using ultrasonic probes with clad steel buffer rods having high signal-to-noise ratio (SNR) are presented. Due to the high SNR of the ultrasonic probes used, backscattered ultrasonic signals from inclusions, which may be oxide films and/or particles, in molten Mg and those from silicon carbide particles, having an average size of 50f.Ull, added in molten AI are successfully detected with reflection configurations of pulse-echo and/or pitch-catch modes at an ultrasonic frequency of 10 MHz. In addition, relative cleanliness evaluation of molten Al and Mg is demonstrated. In order to establish the procedure and to investigate the optimum system configurations for cleanliness evaluation of molten metals, particle flow simulation system using water and polyvinyl chloride (PVC) particles has been constructed. Counting the number and measuring the size distribution of the PVC particles, having an average diameter of 128um, suspended in water with the PVC volume concentrations of 5ppm and 10ppm are performed with ultrasonic pitch-catch mode. The counted numbers of particles by the presented method and system have good agreement with the calculated results with a count error of less than 10% or two counts. Based on the results obtained with water simulation experiments, the prototype system for cleanliness evaluation of molten Mg by counting and sizing inclusions has been developed. Keywords: Ultrasound, Clad buffer rod, Molten metal, Aluminum, Magnesium, Inclusion detection, Cleanliness measurement, Counting, Sizing

Jan 1, 2003

By Tianjiao Luo

Some literatures discussed on how to recycle the various reagent, but the discussion on how to reuse the waste liquid directly is very little. How to reuse the waste liquid directly was researched in this paper. Firstly, the waste liquid should be filtrated to remove the impurity; then some quantity of H2O2 solution was dripped into the waste liquid to pretreat it; finally, CuSO4solution was added into the treated waste liquid and the pH was adjusted to about 12, then some HCHO solution was added into the waste liquid, in which the treated carbon fiber can be plated. The morphology and composition of coatings were investigated by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS), the deposition rate was mensurated by the way of dissolution. The results indicated that, the plating effect was basically identical with new plating solution, and the solution is stable, and the plating rate is still about 0.8µm/h, and the copper coating is even and combines closely with carbon fiber. According to this way, the waste liquid can be reuse 5~7 times.

Jan 1, 2006

By Jian Li

Developing the Generation IV nuclear reactor is an international collaborative effort. One of the most promising Gen IV nuclear reactor designs is the supercritical water (SCW) concept, in which the water coolant runs at about 625 oC at the outlet. Under this temperature and high pressure condition, the cooling water is at supercritical state, which poses significant demand for both in-core and out of core materials. High-temperature mechanical properties, corrosion resistance and radiation damage are some of the key challenges. At present, no single commercial material can meet all the requirements of the severe SCWR conditions. Corrosion experiments per-formed under SCW condition yield various kind of corrosion modes, some are very challenging to characterize using conventional techniques. A combination of various advanced characterization techniques proofed to be essential to understand the root cause of materials? degradation.

Jan 1, 2010

By T. P. R. de Jong

Dual energy X-ray transmission imaging is extensively applied for safety luggage inspection. Its advantages are its rapid scanning rate (25 to 100 cm/sec) at approximately I mm resolution and simultaneous thickness independent metal identification. This is especially advantageous for secondary scrap metal inspection and automatic sorting. Other applications include metal product inspection, bale control, and waste processing. Recent progress in development of an automatic on-line sorter for bulk solids is presented and discussed. Besides various non-metal applications (solid fuels, wastes etc.) it appeared particularly effective in light metal sorting. As inspection tool better control of difficult to monitor solid bulk streams, batteries, bales and other related metals becomes possible.

Jan 1, 2003

By Frederico Muylaert Margem, Jarbas Bravo Neto, Sergio Neves Monteiro

"The mechanical behavior and the fracture characteristics of composites with DGEBA/TETA epoxy matrix reinforced with up to 40% in volume of continuous and thinner ramie fibers were evaluated by tensile tests. Specimens with selected thin fibers aligned along the tensile axis were room temperature tested to rupture. The fracture surface was analyzed by scanning electron microscopy. The results showed significant increase in both the ultimate tensile strength and the elastic modulus. The fracture analysis indicated the possible mechanism for the fiber/matrix interaction, which could be responsible for the composite performance.IntroductionThe fiber reinforced polymer composite emerged in the middle of last century as a versatile engineering material for applications requiring mechanical resistance in association with lightness. Its most commonly used example is ""fiberglass'', i.e., a thermoset polymer matrix composite reinforced with glass fiber. Indeed, ""fiberglass"" has a specific strength of the order of 500 MPa.cm3/g, which is the double of the strongest steels like the maraging. This motivated, at earlier times, ""fiberglass"" to replace many conventional materials including wood and natural fiber composites. Today, ""fiberglass"" has a wide range of uses from aerospace systems and appliances to sport and leisure components. However, its fabrication as well as those of any synthetic fiber such as carbon and aramid composites, requires a relatively large amount of energy. Presently, a growing concern exists regarding the consequences to the environmental by gases like C02 associated with both the energy consumption and the processing of synthetic fibers and their composites. These gases are well known responsible for global warming [1]."

Jan 1, 2011

By J. Smuts

The mixed-valence iron silicate ISCORITE (Fe7Si010) was identified recently in a number of ironmakingmater1als, some of which were first produced more than a century ago. Although the existence of iscorite was not reported before 1967 and published phase diagrams do not make provision for it, the morphology of the phase in all the materials that were examined suggests that it is stable under a variety of conditions. It is shown that is-corite can accommodate various foreign cations in its lattice where they can replace Fe and/or Si. The morphology of is-corite in a number of materials of different origin is shown in relation to iron oxides and silicates in optical and SEM/BSE images.

Jan 1, 1991

An EAF dust generated in a Swedish steel mill has been leached in hydrochloric acid at The solution obtained has been subjected to purification by cementation followed by precipitation of zinc with sodium carbonate. The thermal decomposition of the precipitate was studied using thermal analysis and X-ray diffraction. The results show that during the calcination of the precipitate three different reactions occur. The decomposition of the solid phases Zn5(CO3) (OH)6, CaZn(CO3)2 and CaCO3 occur completely at 370°C, 560°C and 940°C respectively, yielding a final product containing 61.9% ZnO and 38.1% CaO. Methods to minimize calcium and manganese in the final product are discussed.

Jan 1, 2003

By H. Jiang, S. Yang

"The main processes for nickel metallurgy in China consist of electric arc furnace smelting to produce low grade nickel matte and converter to high grade nickel matte, grinding and flotation to separate nickel sulfide from copper sulfide and direct electrolysis of nickel matte. Systematic studies on the properties of electric furnace slag, smelting process for nickel matte, anodic process of nickel matte, cathodic process of nickel electrolysis have been done in our labs. In addition, an approach to a new hydrometallurgy process for nickel matte has been done. The feature of the new process is one stage acidic leaching of high grade nickel matte. The leaching solution could be purified by deposition way or by solvent extraction way. There are two leaching rate-determing steps, chemistry reaction-determing one at temperatures below 600C and diffusion-determing one at temperatures higher than 600 c. The acidic leaching fraction reacted dvaties with leaching time t according to the equation 1-(1- a ) 1/3=kt. The experimental data also show that the leaching reaction rate varies with concentrations of H+, Cl-, and it is also effected by copper sulfide and Cu++. The Cu++ ion can retard the leaching reaction due to forming a copper sulfide layer on the matte surface and the equation 1- 2/3 a. - (1- a: ) 2/3 akt can be used for the case. However the copper sulfide added into nickel matte can facilitate the leaching process. The research work for nickel metallurgy done by others in China has also been mentioned in this paper.Large scale production of nickel in China started in 1960s.The main processes consist of electric arc furnace smelting to produce low grade nickel matte and converter to high grade nickel matte grinding and floatation to separate copper sulfide from nickel sulfide and direct electrolysis of nickel matte.To reduce nickel loss in slag a reseaech group organized by Jinchuan Company and Central South Institute of Mining and Metallurgy (now the Central South University of Technology) measured the viscosity surface tention density conductance melting point and structure of the slag(I).lt has been found that the physico-chemical properties of the slag depend on the components SiO2 ,MgO and FeO but FeO in the slag is too high and the statistic analysis of data from industry gave an equation to correlate the content of Ni in slag with the content of Ni in matte and the composition of slag again it was pointed out that the content of FeO in slag effected the loss of Ni in slag very much (2). The ratio (FeO+MgO) to SiO2shouid be less than 1.13 and the content of Fe3O4should be as low as possible but the reaction"

Jan 1, 1988

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006

By C. M. F. Vieira

In the county of Campos dos Goytacazes, north of the State of Rio de Janeiro, Brazil, there is a large production of red ceramic, mainly perforated bricks. A percentage of these bricks are damaged during the firing processing and become a red ceramic waste. This work investigates a possible solution to this environmental problem through the mixture of fired brick wastes, up to 20 wt.%, with clay bodies to produce red ceramics. Cylindrical pressed bodies were fired at temperatures varying from 500 to 1100ºC. After firing, samples were then tested for linear shrinkage, water absorption and mechanical strength. The results showed that brick waste addition did not changed the workability of the clay and that up to 5 wt.% of waste no detrimental effect occurred on the fired properties at all temperatures.

Jan 1, 2010

By María Cristina Ruiz

Enargite rich copper concentrates can not be treated by conventional smelting/converting technology and thus nonconventional methods such as leaching must be used. Since enargite (Cu3AsS4) is a hard to dissolve mineral in acidic solutions, pyrite, a common impurity in copper concentrates, could be used to increase the enargite dissolution rate. On this matter, we present in this work experimental data on the pressure leaching of a mixed enargite-pyrite concentrate in H2SO4-O2. The results show that the dissolution of enargite from the mixed concentrate is considerably faster than the dissolution of pure enargite mineral. The leaching rate increases significantly with temperature. Over 98% of enargite was dissolved in leaching 64 micron size particles at 200 ºC and 100 psi of partial pressure of oxygen in just 30 minutes. A change in the partial pressure of oxygen from 50 to 150 psi showed also a large influence in the leaching rate.

Jan 1, 2010

By A. F. Saavedra, N. E. Richards, C. J. McMinn

"The aluminum industry in general and Reynolds Metals Company in particular have continued to support development work for improvement of the Hall cell design and for alternative processes for the reduction of alumina. The evolution of the Hall cell design will continue into the next century as a result of further development of mathematical models, sophisticated control systems and new materials for cell components. This paper discusses the areas in which the new generation cell advances will differ from the present day design. Additionally, Reynolds Metal s has supported work for the development of a carbo thermic process to reduce alumina. Theoretical work has indicated that this process could possibly have economic advantage over the Hall process. Several complicated furnace configurations have been proposed to provide the conditions for successfully reducing alumina. The results of small pilot scale operation and most promising furnace design are discussed. For comparison, projected capital investment costs and operation costs are discussed. IntroductionThe evolution of the Hall-Heroult process will continue into the next century. This evolution will be influenced by economics, more .restrictive environment and worker protection requirements, and technological development. These factors will also cause changes in the competitive position of alternate processes for aluminum production.Several aluminum producers have made major investments in alternate processes for aluminum production in the past three decades and there is continued support in some companies for improvements in the Hall-Heroult process and for alternate processes. The more visible development work in reduction technology, not aimed at significant process changes, is in the areas of higher amperage cells with bus bar designs to reduce harmful magnetic effects, more advanced and automated feed, voltage and electrolyte composition control, improved energy efficiency and sol id waste disposal . Efforts to bring significant change to the reduction process are being made in development of materials that can function as inert anodes and cathodes. These materials could lead to the development of reduction cells with multiple bipolar electrodes operating on oxide feed and fluoride electrolytes. Development work on new processes was reduced in the last decade by several companies because of economic and technological realities. Reynolds Metals supported work on a carbothermic process to reduce alumina and produce commercial pure aluminum. This work progressed through small pilot plant operation, and resulted in development of furnace designs and operation regimes. This paper reviews how this and other technologies could influence the reduction of alumina beyond the year 2000."

Jan 1, 1988

By Ulrich E. Klotz, Gemot Pottlacher, Shahid Mehmood

"Platinum alloys are frequently used in technical applications and in jewellery. Their thermophysical properties such as density, heat capacity, thermal conductivity and surface tension play an important role in casting processes and are required as input data for casting simulation. Scope of this work was to investigate these properties by different methods. Platinum and four alloys namely, Pt96Cu4, Pt68Cu32, Pt50Cu50 and Pt25Cu75 were investigated. Melting range and thermal expansion was measured at fem by DSC and dilatometry, respectively.At TU Graz wire shaped samples were investigated by an ohmic pulse heating technique. This technique allows the calculation of specific heat capacity and the temperature dependencies of electrical resistivity, enthalpy, and density of these alloys in the solid and liquid phase. Experimental results were compared with available literature and data from thermodynamic calculation using the SNOBl database and ThermoCalc.IntroductionPlatinum is a precious element and its alloys are commonly used in jewellery. But Platinum is much more difficult to cast then other jewellery elements like silver or gold, because of its high melting temperature, large shrinkage during freezing, low thermal conductivity, high surface tension, and high viscosity. As a result there arise problems during casting. Hence to resolve these difficulties a detailed study of thermophysical properties of solid and liquid platinum and its alloys is necessary for simulation and casting. The Platinum alloy samples were prepared by vacuum induction melting and casting into copper molds. Rods of 3 mm in diameter and a length of 80 mm were prepared and drawn to wires of 0.5 mm in diameter."

Jan 1, 2011

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By G. D. Sandrock

The science and technology of roan temperature rechargeable metal hydrides began about 1969 with the discoveries that the intermetallic Compounds LaNi5 and TiFe could be, conveniently hydrided and dehydrided at roan temperature and modest H2 pressures. Subsequently, this lead to the development of a broad family of REE-containing AB5 hydrides and numerous applications that make use of the extraordinary H2-absorption and reaction-heat properties of these materials. Some of the applications include H2 storage, compression and separation, as well as heat pumping, heat to mechanical energy conversion and electric energy storage. This paper briefly reviews the fundamental phenomenology of metal hydrides, the history of the use of REE's in rechargeable metal hydrides, the practical engineering properties of these materials and the applications that have evolved around them. The rechargeable nickel metal hydride battery, a new vial alternative to NiCd cells, stands at the forefront of the applications.

Jan 1, 1992

By Benoit DeBecker

Laboratory-scale experiments have shown that chromium metal could be recovered from chromate wastes by modifying slightly the chromium electrowinning flow-sheet. After reduction by sulhr dioxide and precipitation of chromic hydroxide, the solid residue is dissolved in the chrome alum solution and the metallic impurities are removed by cementation on manganese. The presence of dissolved manganese in the electrolyte does not affect the cathodic deposition of chromium and it eliminates the anodic production of Cr(V1).

Jan 1, 1994

By F. Robert Hubbard

IMCO Recycling Inc. has developed a new, patented technology for the production of fertilizer, K-SOIL?, as a by-product of its aluminum recycling operations. This new technology can substitute for conventional technology which now results in a saltcake residue that is placed in 'landfills. Four years of research and development work by IMCO culminated in a U. S. patent issued April 5, 1994. As part of the technology development effort, IMCO engaged the services of a nationally renowned research organization and a prominent university. These two organizations have conducted in-depth agronomy studies In the laboratory, greenhouse, and the field. Results have shown K-SOIL? to be performance equivalent, on a nutrient content basis, to conventional potash fertilizer. The first field applications on commercial farms were made in the spring of 1994. K-SOIL? is a potassium-bearIng, granular solid which may find use in fertilizer blends, direct application, and other forms of fertilizer products. The overall benefit of this new technology is to create a useful by-product rather than generate a useless residue and, thereby, reduce or eliminate the amount of salt cake now placed in landfills. As such, It is a significant, step toward IMCO's ultimate goal of complete recycle.

Jan 1, 1995

By Andrzej Warczok

Intensive smelting of copper concentrate in Teniente Converter (CT) leads to the production of high grade matte and highly oxidized slag. Smelting slag is processed in Teniente vascular slag cleaning furnace. The slag composition and forms of copper affect the slag cleaning process and final copper content. Converting of high grade matte in Pierce-Smith converter faces some difficulties in proper slagging of iron oxides. Overblowing in copper making stage allows for slag liquidation but leads to high content of copper oxide in converter slag. Converter slag recycling into CT results in the increase of the participation of oxidic copper. Separate treatment of converter slag and its impact on the forms of copper in CT slag has been analyzed. Thermodynamic properties of a system and kinetic limitations pointed out the negative effect of converter slag recycling on the forms of copper and copper recovery in slag cleaning stage. Experimental results of slag cleaning tests in a crucible scale as well as microscopic examination of laboratory and industrial slag samples supported the above analysis and permitted to formulate recommendations of separate processing of converter slag. Keywords: copper, losses, slag, recycling

Jan 1, 2001

By F. Kassabji

This publication presents the main experimental and theoretical results on the recovery of aluminum scrap (dross and Used Beverage Can) without use of any addition of fluxing salts. Dross and UBC's processing experiments have been conducted in a rotary plasma furnace operating in the transferred and non-transferred mode, using different plasma gases. The investigation involved the treatment of more than 100 kg of dross and other aluminum residues using plasma torches with less than 100 kW power. The experimental work showed that this process is .far more economical and kind to the environment than the conventional route using a salt flux. An equilibrium thermodynamic calculation at elevated temperature makes possible the prediction of by-products at various temperatures for different plasma gases.

Jan 1, 1994