Search Documents

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450 °C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By Bingyi Bai, Lifeng Yang, Yanling Guo, Jieyu Zhang, Guoding Gao

In terms of special resources with iron, niobium and rare earth coexisting in Baiyuneboite, the new smelting technology of ferrocolumbite was studied. Reduction experients for the Baiyuneboite and explores ore phase change of Baiyuneboite in the process of reduction was conducted with graphitic carbon as the main reducer and a temperature below 1000 ℃. Moreover, it studies the influence of reducer, roasting temperature and grind fineness on the reduction as well as focuses on the evolution course of iron phase. Through the analysis on in-situ XRD of the raw ore and carbon addition ore, it also develops microstructure change rules of Fe ore phase and ore phase of paragenetic elements for composite ore(Ca, Si, Nb, F) in the process of reduction roasting. In addition, the impacts of temperature on the reduction process are also discussed. With regard to minerals of different particle sizes, the thesis will explore their ore phase changes and microstructures after 10 hours’ reduction under 900 ℃.

Jan 1, 2015

By Gaballah Djona M.

Spent hydrorefining catalysts contain about 5 % of CoO and/or NiO, 12 % of MoO3 and up to 10 % of V205. They are generally supported by alumina and contain up to 25 percent of C, S and hydrocarbons. Such materials are potentially hazardous to the soil and to water resources. Selective chlorination of raw unroasted samples with Cl2 + air gas mixture had been investigated. At temperatures lower than 600 °C, it was possible to recover more than 90 % of nickel and cobalt chlorides, about 99 % of the molybdenum and up to 75 % of vanadium chlorinated compounds. CoCl2 and Ni/Cl2 were extracted from the chlorination residues by their dissolution with acidified water. Molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The chlorination of Al2O3 could be limited to less than 6 %. The scale up of this treatment was successful and a flow-sheet is proposed.

Jan 1, 1995

By Jose M. Gomez-Vega, Osamu Takai, Atsushi Hozumi, Hiroyuki Sugimura

"Ongoing research is reported aimed at improving the properties of mesoporous silica-based coatings on various substrates for optoelectronic or medical applications. Tetraethylorthosilicate (TEOS) was selected as the silica precursor, and amphiphilic triblock copolymers poly( ethylene oxide)- poly(propylene oxide)poly( ethylene oxide) as the surfactant micellar template or structure-directing agents. Cetyltrimethylammonium chloride (CTAC) was also used as a control agent. The effect of the templating agent and type of substrate (glass, Si, and Ti) on the mesoporosity, particularly on the alignment of the mesochannels, has been investigated. Three · different treatments (thermocalcination, photocalcination, and solvent extraction) have been also studied to remove the organic templates.IntroductionThe fabrication of mesoporous silicate-based materials through the utilization of a sol-gel process, where cooperative organization of organic and inorganic species takes place, provides a versatile approach to nanoscaled structures with potential applications in fields such as catalysts, optoelectronics, biomaterials, etc. Compared to conventional low molecular weight surfactants, self assembly of amphiphilic·block copolymers can result in mesostructured materials with larger pore sizes (up to 30 nm).1 Most of the synthetic strategies use silicon alkoxides as the silica precursor, although non-silicate metal alkoxides, e.g; Ti, Zr, Al, and B, have been also used to obtain different mesoporous materials, or even mixed metallic oxide systems. 2 Recently, Yang et al. 3 • 4 were able to synthesii:e a great variety of mesoporous metal oxides ID nonaqueous media using inorganic precursors (metal chlorides) and block copolymers as structure-directing agents."

Jan 1, 2000

By Guo Xueyi

The dissolution behaviors of valuable metals, lead and zinc, from secondary fly ash generated in municipal incineration plants were investigated using some lixiviants: sulfuric and hydrochloric acids, acetic acid and some chelating reagents including L-asparaginic-N,N-diacetic acid (ASDA), a biodegradable, and therefore, environmentally benign novel chelating reagent. It was found that zinc exists mainly as ZnO, whereas Pb probably as PbOHCI and PbO, and the easily soluble components in SFA are KCI and NaCl. Suitable amount of HCI can dissolve all of lead and zinc from SFA. Sulfuric acid can selectively extract zinc leaving lead in the residue. Ethylenediaminetetraacetic acid (EDTA) is an effective chelating reagent to extract both zinc and lead. Although ASDA and diethylene¬triaminepentaacetic acid (DTPA) can selectively extract more than half of lead from SFA, it would by no means be regarded as highly effective reagents for the extraction of these metal values. Keywords: Lead, Zinc, Secondary fly ash, Leaching, Dissolution

Jan 1, 2002

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc. Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed.

Jan 1, 2003

By Dietmar Eifler, Marcus Klein, Hendrik Kramer

Conventional methods to characterize the fatigue behavior of metallic materials are very time and cost consuming. That is why the new short-time procedure PHYBALCHT was developed at the Institute of Materials Science and Engineering at the University of Kaiserslautern. This innovative method requires only a planar material surface to perform cyclic force-controlled hardness indentation tests. To characterize the cyclic elastic-plastic behavior of the test material the change of the force-indentation-depth-hysteresis is plotted versus the number of indentation cycles. In accordance to the plastic strain amplitude the indentation-depth width of the hysteresis loop is measured at half minimum force and is called plastic indentation-depth amplitude. Its change as a function of the number of cycles of indentation can be described by power-laws. One of these power-laws contains the hardening-exponentCHT eII, which correlates very well with the amount of cyclic hardening in conventional constant amplitude fatigue tests. To identify heat-treatment-parameters and SAE 52100 TRIP-alloys with high hardening rates as well as their damage tolerance the PHYBALCHT- and PHYBALLIT-method were used. One modified SAE 52100 TRIP-alloy was investigated in detail. The fatigue behavior and the cyclic hardening of the selected SAE 52100 TRIP-alloy was investigated and compared with conventional SAE 52100. Conventional stress-controlled fatigue tests were performed on a servo-hydraulic test system with a frequency of 5 Hz and a load ratio of R = -1. Different rates of cyclic hardening were identified. The size of the nonmetallic inclusions leading to crack initiation and the number of cycles to failure were used to evaluate differences in the damage tolerance capability.

Jan 1, 2015

By Z. R. Llanos

This paper presents a review of industrial and experimental processes for the recovery of molybdenum, vanadium, nickel, cobalt and aluminum from spent hydrotreating or hydrodesulfurization catalysts. Numerous processes have been developed in a laboratory and pilot scale. However, worldwide, there are only four well established commercial facilities currently in operation. The installed capacity of these facilities exceeds the availability of spent catalysts and may be sufficient to assimilate future increases of spent catalysts. Despite liability risks; significant quantities of spent catalysts are still being landfilled. Changing regulations that may affect the future handling and disposal of spent catalysts are also reviewed.

Jan 1, 1995

By Berger. P.

The accepted definition of the function of an edge protector fails to specify adequately the several tasks which it must perform to be functionally effective: detailed analysis of these tasks leads to the reasoned conclusion that they cannot satisfactorily be fulfilled by the conventional types of "edge-strips". The true cost of edge protector failure is cumulative: renewal costs are dwarfed by the increased operating expenses and production losses which result from but partial or incipient failure of the edge-strip; yet, the several supposedly improved types, for use with starter-blanks, generally were "built down to a price", prolonging the agony, as it were. Clearly, a fresh appraisal of the problem was overdue, and more especially so with the advent of "permanent" cathodes. As a result, new methods of edge .protection have been developed, including the so-called "EDGEWISE" system in which the present author as patentee *) has a vested interest-which he hereby declares. Due mention is made of recent progress in protecting the edges of aluminium "Jumbo" cathodes in zinc electrowinning operations, although the present Paper is more concerned with edge protection of starter-blanks and permanent cathodes in copper ER/EW processes, where most of the "old" problems now may justifiably be claimed to have been overcome, Mention is also made - albeit at this time necessarily only briefly, and confined to edge protection - of "rigidized" metal blanks and permanent cathodes: a most recent development**) which may prove to represent a "breakthrough": time will tell.

Jan 1, 1987

By Pengfu Tan

Electric arc furnace (EAF) dust from the steel industries is listed by the United Sates EPA as a hazardous waste under the regulations of the Resource Conservation and Recovery Act due to the presence of lead, cadmium and chromium. The disposal of the approximately 650,000 tons of EAF dust per year in the U.S. and Canada is an expensive and unresolved problem for the majority of steel companies. The Waelz process has been considered as the best process for treating EAF dust. A process model, combined thermodynamic modeling with heat transfer calculations, has been developed to simulate the chemical reactions, mass and heat transfer and heat balance in the kiln. The injection of air into the slag and the temperature profile along the kiln has been modeled. The effect of (CaO+MgO)/SiO2 on the solidus temperature of slag has been modeled also and discussed. Some optimizing results have been presented in this paper.

Jan 1, 2005

By Amir Rehmat

The Institute of Gas Technology has developed a fluidized-bed process for recovering direct reduced iron from blast furnace flue dust a material currently considered to be a waste from the iron and steel industry. In the process, a portion of the carbon in the flue dust is combusted to supply energy for the endothermic reaction between carbon and steam. The reaction produces reducing gases comprised of carbon monoxide and hydrogen both of which react with iron oxides to produce reduced iron. Up to 95 percent of the iron oxides contained in the waste stream can be reduced to elemental iron. The vitiated reducing gases emanating from the process can be used as fuel in the plant. The yield of iron depends upon the quantity of iron oxide present in the flue dust and generally ranges from 20 to 30 percent of the waste stream. The investment cost estimated for a single processing train dedicated to one steel plant can be recovered in less than one year.

Jan 1, 1996

By Thomas R. Wildeman

Experimental methods for studying vapors over solid minerals are reviewed and an especially developed method using atomic absorption is described. The method is used to study vapor pressures over Te. Ag, Au, Ag2Te, and AuTe2 from 250°C through 10S0oe. Vapor pressures observed and, concurrently. sintering properties are significantly altered by the form of the solid. The vapor pressures of the tellurium compounds reveal complex processes occurring on the surfaces of the solids. The data given also point out a method of recovering precious metals from their telluride minerals w

Jan 1, 1987

By Stephen Chryssoulis, Stamen Dimov

Detection and quantification of precious metals (Au, Pd, Pt, and Rh) in spinels and silicate minerals is important for establishing the maximum attainable recovery by sulphide flotation. To achieve this goal subpart per billion (ppb) detection limits are required plus the ability to quantify results. Existing quantitative microbeam techniques (EPMA, PIXE, SIMS, TOFLIMS) have limits of detection in the O. l-200ppm range. Time-of-flight resonance ionization mass spectrometry (TOF-RIMS) is a microbeam analytical technique that allows for the identification and quantification of atomic species in very small quantities. It utilizes a tunable laser source for resonant excitation and ionization of a particular element of interest and has some unique features: elemental selectivity, linear response over a large dynamic range and very high sensitivity. The analysis consist of three steps: (i) the solid sample is vaporized by laser ablation to form a plume containing neutral atoms, (ii) the neutral atoms of a specific atomic element in the plume are resonantly excited and ionized by another tunable laser, and finally (iii) the ions created are mass analyzed in a time-of-flight mass spectrometer. A TOF-RIMS mass spectrometer was developed at AMTEL for trace element analysis of Au, Pd, and Rh in minerals. The spectrometer was calibrated using homogeneous CANMET and NIST reference samples covering three orders of magnitude in concentration. Attained minimum detection limits (MDL=2cr of the background) are in the low ppb range.

Jan 1, 1999

By Payman Roonasi

Having knowledge of mechanism of magnetite formation is essential in a number of industrial processes including magnetite synthesis and corrosion of iron. In this study, magnetite nanoparticle was synthesized via two different ways; coprecipitation of iron (II) and (III) and oxidation of ferrous hydroxide. The samples were characterized using X-ray diffraction (XRD), Mid-Far IR spectroscopy, scanning electron microscopy (SEM), chemical analysis for determination of Fe II/Fe III ratio and ICP-MS for iron isotopic ratio (56Fe/54Fe) measurement. Since fractionation of iron isotopes depends on reaction rate and bonding strength, interpretation of the isotopic data with respect to the possible mechanisms is discussed. No fractionation of iron isotopes was observed for the magnetite synthesized by coprecipitation, whilst magnetite formed from ferrous hydroxide showed higher abundance of 54Fe compared to 56Fe in the beginning of reaction, implying the significance of the following reaction:

Jan 1, 2009

By David G. Dixon

A general, unsteady-state model for leaching of one or more solid reactant species from a non- reactive, porous, spherical pellet is derived in dimensionless form for the interpretation of leaching data, and for use in the design of coarse-ore leaching processes. The effects of diffusion rate, chemical reaction rate, variable reaction order, and competition between multiple solid reactants are examined using the concept of the effectiveness factor. It is shown that the model is capable of simulating both "reaction-zone" and "heterogeneous" kinetics, depending on the choice of three dimensionless parameters. Results of batch leaching tests of artificial ore pellets are presented, and their relationship to the model is discussed.

Jan 1, 1993

By S. Kang, D. G. C. Robertson

Slag cleaning furnaces require extensive wall cooling because they involve the use of a superheated slag bath. This is in direct contrast to smelting furnaces, where the wall is usually (but not always) protected by "banks" of solid charge. In order to understand the heat transfer and flow in slag cleaning furnaces a number of model studies have been carried out using molten wax to simulate the slag. Wax is a good model fluid because, like slag, it has a high Prandtl number. Wax models cannot simulate the behavior close to the electrodes (DC arc or AC submerged), but they can and do give a good simulation of the flow and heat transfer at the wall. An understanding of these phenomena is of great importance for the design of cooling panels in the walls of the furnace. Since superheated molten slag will eventually wear away any refractory bricks over time, the wall cooling must be designed to form a frozen layer of slag, referred to as a "freeze lining". The heat flux density (Q/A) required to do this is given by Q/A = h* ?T, where h is the heat transfer coefficient in the slag phase at the wall, and Li T is the superheat (bulk slag temperature - liquidus temperature). Both Q/A and h vary greatly with position and both are usually a maximum at the slag line. In the experimental work, molten wax baths were heated by block heaters to provide similar energy densities to those encountered in commercial slag cleaning furnaces. This procedure was considered to be valid since most of the electrical energy into a furnace bath is dissipated as heat. Gas stirring was used to simulate the gas evolved at the electrode in real furnaces - the quantity of this gas could be estimated from a knowledge of electrode consumption. The similarity criterion was equal gas flow per unit area of surface, in model and prototype. Heat transfer coefficients were measured in the models as a function of power density, gas stirring, superheat, etc., and could be related to the full-scale operations by the use of dimensional analysis.

Jan 1, 1999

By R. S. Tahautdinov, A. N. Posazhennikov, V. V. Bastrygin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2011

By Cristián Araya L.

A dynamic agglomeration, heap leaching, solvent extraction and electrowinning software, called NICO, has been developed in order to either design or simulate copper ore recovery plants. NICO contains a library of routines, each representing a unit operation or piece of equipment, which are assembled like a meccano to match almost any wet plant configuration. Routines include agglomeration or curing either in drums or belts, belt conveyors, heap stacking and reclaiming, heap leaching of oxide, sulfide or mixed copper ores, heap irrigation, drainage, ponds, mixer-settlers, filters, columns, coalescers, tanks, electrowinning cells, pumps, and all connections and related piping. All models are semi- phenomenological, i.e., they include all physical-chemical, mass, thermal, transport equations, which are required to represent as closely as possible the equipment or unit operation. However, operating experience has been incorporated into the model in order to make it simpler, faster and reliable. This experience has been tested in several plants in Chile since 1992. Site meteorological data is simulated also; in this way the model is responsive to weather conditions (temperature, solar radiation, ambient humidity, atmospheric pressure, wind velocity, etc). NICO has been used recently for design and optimization studies in copper plants in Chile like Radomiro Tomic, Collahuasi and Zaldivar. A user-friendly interface allows fast and comprehensive simulations. The entire plant is shown in a single graphic screen, so the user can see all the relevant information, and soft-keys are provided in order to change parameters on-line and watch their effect in final copper production in cathodes. Model also calculates and reports operating parameters, as well as estimated investments and operating costs.

Jan 1, 1999

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006