Search Documents

By S. Yin, A. Bogno, H. Henein, P. Natzke

Impulse Atomization (IA) (a single fluid atomization technique) was used to rapidly solidify Al- 4.5wt%Cu and Al-4.5wt%Cu-0.4wt%Sc under argon atmosphere. In addition to the IA-generated droplets, the same technique was used to produce strips by Spray Deposition (SD) of the same alloys on a copper substrate with and without oil coating. The rapid solidification microstructures were analyzed using Scanning Electron Microscopy (SEM). From the SEM images, the amount of eutectic and the secondary dendrite arm spacing (SDAS) were measured. These SDAS results lead to the estimation of cooling rate. The eutectic fraction coupled with the metastable extension of the solidus and liquidus lines of Al-Cu (Sc) phase diagram lead to the estimation of primary and eutectic undercoolings. A comparison of the solidification path of the droplets and the strips was done as well as the analysis of the effects of scandium.

Jan 1, 2015

By R. P. Maloney

The economic viability of four depleted mines near Kennicott, Alaska, was determined by the Bureau of Mines to assess their profitability if they were developed today and thus estimate cost data for a medium-sized mine, mill, and town complex. This information should help the State and Federal Governments appraise the potential development of similar-sized mining operations in Alaska. Modern conventional mining and milling techniques were assumed, and I capital and operating costs were derived using flowsheets and standard costing methods. A total capital investment of $37.6 million was necessary to install a 1,000-ton-per-day shrinkage stope mine, flotation-type mill, and support facilities; capital requirements were divided about evenly among the three components. Operating costs, including labor, supplies, power, water, and ' indirect and fixed costs, totaled $42.79 per ton of ore; the mining accounted for nearly one-half the cost. To obtain a 12-percent discounted cash flow rate of return on investment, the analysis showed that the ore could be mined and milled, and the concentrate could be trucked via public roads to a dock facility in Valdez, Alaska, barged to Tacoma, Wash., and smelted and refined for 34.7 cents per pound for copper and 104.0 cents per ounce for silver. The average May 1972 price was 52.6 cents for copper and 158.3 cents for silver. The same set of data was used to examine the economic viability of the mine with the cost of constructing a private road from McCarthy, Alaska, To Valdez, Alaska. The 148-mile road added $53.3 million to the original capital costs and raised the required price of copper to 57.4 cents per pound and the required price of silver to 172.0 cents per ounce. The additional coat of building, maintaining, and paying taxes on a private road from McCarthy, Alaska, to Valdez, Alaska, would make this venture uneconomical.

Jan 1, 1973

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

By H. I. Smith

WHEN Spain established colonies on the North American continent, some of her land grants, in what is now the United States, reserved to the Crown deposits of gold, silver, and mercury. Later mineral rights were reserved under some of the English Crown charters involving land in the eastern part of North America, with provisions for the payment of royalties thereon to the Crown. Reservation of mineral deposits to the United States Government was instituted by an ordinance of Congress on May 20, 1785, which applied to such deposits in the Northwest Territory, then north of the Ohio River and east of the Mississippi River, and provided that there should be reserved "one third of all gold, silver, lead, and copper mines, to be sold or otherwise disposed of as Congress shall hereafter direct." Little was known then of the mineral resources of the country; the Great Lakes copper region had just come into the possession of the United States by treaty and much of the western mineral land still belonged to France and Spain. The policy of leasing mineral deposits was enacted by Congress under the act of March 3, 1807, which provided that "the President of the United States shall be, and is hereby, authorized to lease any lead mine which has been or may hereafter be discovered in the Indiana Territory, for a term not exceeding five years," and in the same year the Government reserved 345,600 acres of land in northern Illinois, valuable for lead. In 1816 Congress provided that in all cases where a tract of public land containing a lead mine or salt spring was applied for by settlers on the public domain, no permission to work the mine or spring would be granted without the approbation of the President of the United States. By the act of March 1, 1847 (9 Stat. 146), the control of mineral lands was transferred, with all records, from the War Department to the Treasury Department, and by the act of March 3, 1849 (9 Stat. 395), supervisory powers over lead and other mines of the United States were transferred to the Secretary of the Interior. Following the discovery of gold in California in 1848, President Polk advocated the leasing of mineral lands acquired from Mexico under the treaty of 1848. However, owing to the lack of communication and transportation facilities and the consequent difficulty of checking on production and operations, leasing was found impracticable. Mining was permitted to be carried on in each district under rules made by the miners themselves and patterned after the Mexican mining system. To meet the situation, Congress enacted mining laws in 1866, 1870, and 1872, which provided for possession by location and for private ownership, after discovery, by patent of essentially all mineral deposits belonging to the United States, except coal. Many other acts were passed by Congress applying to specific regions and states, reserving salt, lead, or other minerals, some of which provided for the leasing of such deposits. However, very few if any leases were issued thereunder. Not until 1901 (31 Stat. 745) were the mining laws extended to include salt, and in 1910 they were revised to specify salines and associated products. At the turn of the century, it became more and more evident that the mining laws developed for metallic minerals were not practical for the development and conservation of oil and gas, coal, potash, phosphate, or oil shale. Following withdrawals by the Secretary of the Interior as authorized by the act of June 25, 1910, the Department of the Interior recommended leasing legislation; however, it was not until February 25, 1920, that the Mineral Leasing Act was passed by Congress. This act authorized leasing all public lands potentially valuable for oil, gas, coal, phosphate, sodium, or oil shale. The Organic Act, creating the Geological Survey in 1879, imposed upon its director the duty of classifying the public lands.' The early years of the Survey were devoted largely to the accumulation of fundamental data and, with only minor exceptions, land classification was not seriously undertaken until 1906. Since that year, it has been actively pursued with respect particularly to leasable minerals and water power values. On March 3, 1873 (17 Stat. 607) Congress authorized the sale of coal lands of limited acreage to individuals at $10 to $20 an acre, depending on the distance from a railroad, and in 1907 a new scale of prices was adopted by the Secretary of the Interior, based, more logically, on the quality and thickness of the coal deposits, their depth below the earth's surface, and their accessibility. At that time it was much cheaper and easier to obtain incidental title to coal rights under the homestead laws at $1.25 an acre. On March 3, 1909, the first separation act (35 Stat. 844) became a law. It authorized patents, with a reservation of the coal and mining rights involved to the United States, to persons who in good faith had entered public lands under the non-mineral land laws prior to withdrawal, classification, claim, or report that such lands were valuable for coal. It solved the problem only partially, and the practice thereupon adopted by the department of making coal withdrawals "from all forms of entry" instead of "from coal entry" expedited the more complete solution effected by later acts. By the act of June 22, 1910 (36.Stat. 583) withdrawn and classified coal lands were declared subject to entry under the homestead, desert land, and Carey acts, provided a waiver of the coal rights accompanied the application, and by the act of April 30, 1912 (37 Stat. 105) the same privilege was extended to State selections and isolated tracts. The act of August 24, 1912 (37 Stat. 496) extended the separation policy to lands withdrawn for oil and gas in Utah, and finally the act of July 17, 1914 (38 Stat. 509) extended it to all nonmineral filings on public lands theretofore or thereafter

Jan 1, 1955

Mineral Changes that Occur During Coal Gasification

Sep 13, 2010

By I. J. Duckworth

During the last twenty years computers have be-come widely used to assist with the simulation and design of large scale, primary ventilation systems. However, to date there are few computer programs available to help with the modeling of auxiliary ventilation in dead-end headings or tunnels. This paper presents the results of the first year of a research and programming study dedicated to the development of a user-friendly duct simulation tool. Included is a literature review that summarises publications on duct leakage and resistance, on previous programs developed for the simulation of airflow in ducts, and case studies on extended ductlines in mines and tunnels. The methodology behind the development of Ductsim, a Windows based simulation program is presented.

Jan 1, 2000

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed: The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation. This paper is an update of that which the authors prepared for the Infacon X ferro-alloys conference.

Jan 1, 2004

An integrated palynological and sedimentological investigation of four wells from the eastern margin of the Gippsland Basin has resulted in a scheme for classification of palynofacies in this area. Thirteen different palynofacies assemblages are recognised and assigned to particular environments based on the enclosing sediments, which range from alluvial, through coastal barrier to continental shelf environments. Close correlation is observed between the interpreted energy regime of the palynofacies assemblage, and that of the enclosing sediments. Assemblages characterised as reworking surfaces can be correlated with unconformity producing events (ie tectonic activity associated with the opening of the Tasman Sea), and some of the minor eustatic sea level Changes.

Jan 1, 1992

By J. E. Dutrizac, R. J. C. MacDonald, J. B. O'Reilly

"Sometime around 3000 B.C., primitive metallurgists working in the mountainous regions of Asia Minor bordering on the Black Sea (Pontus) produced a soft, easily fused metal today known as lead. It appears certain that the first metal was made by reductive smelting of galena, but whether this recovery arose by the accidental inclusion of galena in the stones of a fire hearth or whether it occurred as a consequence of simple pyrometallurgical experiments on a series of interesting ""stones"" will likely never be known with certainty. The properties of galena, high metallic lustre, great density and facile cleavage, must have excited the ancients, and such ""stones"" would have been the object of primitive testing111 - Shortly after the discovery of lead, the ancients found that the controlled oxidation of this metal at elevated temperatures yielded smaller amounts of a more interesting material, silver. Again, it is uncertain if the production of silver by primitive cupellation techniques was the result of a fireside accident or the consequence of a deliberate experiment, but the important fact is that silver was produced shortly after the discovery of lead. The techniques for making lead and silver spread gradually throughout the entire civilized world, likely as a result of both technology diffusion and independent rediscovery. The physical properties of lead could not have been overly attractive to the ancients, but silver was a different matter altogether. The gleaming white lustre and relative immunity to oxidation quickly assigned silver to the precious materials category, a status it still enjoys. In early times, argentiferous galena was inevitably processed only for its silver values; lead was generally an unwanted byproduct and was frequently discarded as litharge (PbO) during the cupellation process. The silver was eagerly sought, however, and resulted in considerable mining activity culminating in the famous Athenian silver mines at Laurium at the southern end of the Athenian peninsula."

Jan 1, 1999

By P. Tolvanen, A. Jalili

"When hard times strike in the mining cycle, sites tighten their belts and focus on lowering their unit costs. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. Faced with these requirements, site personnel must turn to areas where they can focus their effort for maximum return. For many sites, both in Canada and overseas, focusing on improving flotation cell maintenance is one of the areas where gains can be made for minimum outlay. Due to resource limitations and/or lack of equipment understanding, maintenance on many sites is only conducted on a reactive basis, once equipment fails. This paper will promote the idea that mineral processors should become more familiar with their equipment so they can ensure that the plant’s ability to produce is not compromised. By better understanding the flotation equipment and ensuring the critical components are maintained, it should be possible to unlock value in an operation. Flotation equipment inspections will be discussed in detail, including key items to look for during these inspections. Potential approaches for predicting wear and change-out time for flotation equipment components will be also demonstrated. An example of one approach used at a South African nickel site will be given.INTRODUCTIONWith metal prices decreasing and operating costs rising, concentrator operators are looking for ways to improve their bottom line. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. To meet the expectation of shareholders, mineral processors must turn to areas where they can get the best return for their efforts. One area where there is a large opportunity for improvement is in the maintenance of flotation equipment.On many mine sites, both domestically and around the world, it is quite common to see the philosophy applied of repairing equipment only once it has failed. Though some sites have advanced enterprise management systems and monitoring programs, in the authors’ experience, the decision on flotation equipment maintenance is rarely made on a proactive basis. Two common trends that are evident in the mining industry are that operations are under pressure to keep the plant producing, and maintenance managers generally have very strict budget targets to meet. In addition to these factors, few sites have a good understanding of the financial implications of running with worn or broken flotation equipment. Knights, Jullian and Jofre (2006) summarize this situation well, stating that the lack of correlation between some commonly used maintenance performance measures and key business drivers can lead to maintenance being seen only as a cost center (that needs to be reduced) rather than a tool for productivity improvement."

Jan 1, 2015

By Feng Wang, Guojing Shi, Yangyang Xie, Zizong Zhu, Qiang Wu

The coal chars from northwestern part of China are characterized with high reactivity and low strength after reaction. Four type of coke-making coals selected from northwestern part of China were studied by proximate analysis, ultimate analysis, vitrinite reflectance analysis, and FTIR with curve-fitting analysis to obtain information on their chemical composition and chemical structure. The results show that the studied coals have relatively high values of final contraction of coke residue index (x) and relatively low values of maximum thickness of plastic layer (y) and average vitrinite reflectance. Based on the curve-fitting analysis of FTIR spectra, the aliphatic carbon (Cal), the aromatic carbon (Car), and the molecular structural parameters such as CH2/CH3, fa, Hal/Har, and (R/C)u are determined. The results of curve-fitting analysis indicate that the studied coals are characterized by a large amount of oxygen-containing functional groups and aliphatic side chains.

Mar 1, 2018

By Todd M. Ruff

This report summarizes ongoing research at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, in which collision warning systems for surface mining dump trucks are being evaluated. Common accidents involve these large trucks running over smaller vehicles or pedestrian workers. Collision warning systems currently use one of several methods, including radar, radio-frequency-signal detection, or ultrasonic signals, to detect and warn of the presence of an object or person in the blind spots of the mining equipment. Most available systems have not been tested on large off-highway dump trucks. This report evaluates several systems on two sizes of trucks, a 50-ton-capacity truck commonly used in quarries and construction and a 240-ton-capacity truck commonly used in open-pit mines. Tests were conducted to determine false alarm rates, alarm effectiveness, and reliable detection zones for a person and a pickup truck. The results indicate that radar and radio-frequency identification systems show promise for this application and that several of the improved systems are ready for extensive field tests. However, challenges still exist in applying these technologies to large trucks.

Jan 11, 2000

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By S. M. Bulatovic

The western industrial world has to rely more and more on complex polymetallic sulphide ores as sources for base metals. These ores are composed of fine grained sulphide minerals such as chalcopyrite, galena, sphalerite, pyrite, pyrrhotite and marcasite. The liberation sizes of the individual minerals can range between 30 um and 5 um. Therefore, applying conventional techniques to recover these finely disseminated minerals usually results in unsatisfactory metallurgical performances with high losses of the valuable mineral to the slime , fraction of the tailing. New concepts for treating these polymetallic complex ores are discussed in this paper. Beneficiation techniques utilizing new reagents and a new approach to pulp preparation are described. Some of these techniques were applied to ores from existing concentrators as well as to new ores. The results of these studies are discussed in the following sections.

Jan 1, 1990

By B Mobilio, M Secheny, J Rachocki, G B. Sharrock, A Jäger, J L. Lett, I Brunton, G W. Capes

Establishment of the Cadia East Panel Cave Stage One (PC1S1) commenced with the firing of the first bell in early 2011. Production began with the completion of the undercut in May 2014. PC1S1 used a post-undercut composed of 114 drawbells covering a footprint area of 73 438 m². The extraction level is located at a depth of 1200 m below the surface and is based on a 32 × 20 m El Teniente layout. Cave establishment required the construction of multiple conveyor drifts, a large-capacity jaw-gyratory crusher and ancillary ventilation and pumping infrastructure. Preconditioning via hydraulic fracturing and blasting was implemented at various locations of the cave block height. This paper presents an overview of the key learnings from the commencement of undercutting to surface breakthrough, including rock mass classification and modelling, stress measurements, preconditioning, numerical modelling and cave monitoring.CITATION:Lett, J L, Brunton, I, Capes, G W, Jäger, A, Mobilio, B, Rachocki, J, Sharrock, G B and Secheny, M, 2016. Undercutting to surface breakthrough – Cadia East panel cave (stage 1), in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 65–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By N. R. MacMillan

INTRODUCTION The Bullmoose Coal Project is part of a major development in northeastern British Columbia which comprises a new rail line, a new townsite, powerline, highway, the upgrading of the Canadian National Railway's main line, a new coal port at Prince Rupert and two new coal mines, the Bullmoose mine and the Quintette mine. The total investment by all parties is estimated to be in excess of $2.6 billion and made up approximately as follows : [Table No. 1 $ Millions - Quintette Coal Limited 950 Teck-Bullmoose Coal Inc. 275 Canadian National Railway Company 800 6 British Columbia Railway Company Port at Prince Rupert 280 Townsite, Roads 6- Power ] The new infrastructure is intended to serve not only the Bullmoose and Quintette coal projects but also eventually a number of other coal properties in northeastern British Columbia. The Bullmoose project is structured on a joint venture basis as follows : [Table No. 2 Teck Corporation 51% Lornex Mining Corporation Ltd. 39% Nissho Iwai Coal Development 1 0% (Canada) Ltd. -- 100% ] The mine has a capacity of 2.3 million tonnes of clean coal per year. In the initial years 1.7 million tonnes will be metallurgical coal and 0.6 million tonnes thermal coal. After the first three years of operations the annual production of metallurgical coal will increase to an average of approximately 2.1 million tonnes and the production of thermal coal will decrease to an average of approximately 0.2 million tonnes. At this level of 2.3 million tonnes annual production, the Bullmoose mine has sufficient reserves for at least 26 years of production. History Brameda Resources Ltd. commenced coal exploration in the Bullmoose-Sukunka area in 1969. Teck obtained an option on the Bullmoose coal licences in 1970 and started surface exploration and diamond drilling in 1971. Teck earned a 50% interest in the property, and thereafter expenses were jointly financed by Teck and Brameda. In 1981 Brameda merged with Teck making Teck the sole owner. The initial phase of the exploration program, which was completed in 1975, included 7,200 meters of diamond drilling in 35 holes. During 1976 and 1977, detailed exploration and test work were carried out on the South Fork and West Fork areas where multiple seams close to surfaces indicated the potential for large tonnages of strippable coal. In those two years, work included road construction, detailed mapping and trenching to outline the coal seam traces at the surface, 6,300 meters of diamond drilling in 80 holes, and 300 meters of underground bulk sampling from seven adits. Washability tests and analysis work were carried out on the drill cores and adit samples, and pilot plant washability studies were undertaken. In 1978 and 1979 Teck engineers prepared open pit mining plans and production schedules and Kaiser Engineering was retained to prepare a layout of the plant preparation facility. A feasibility study prepared by Teck's engineering group in January 1982 was the base document used by the Lenders in assessing the technical and economic viability of the project. Property Location The property lies some 650 kilometers northeast of Vancouver, and 87 kilometers south by road from the village of Chetwynd. The Sukunka property (British Petroleum) adjoins to the north, the Mount Spieker property (Ranger Oil Option) adjoins to the east, and the Quintette property is located to the southeast.

Jan 1, 1985

By M Henderson, M Hudyma

Mining-induced seismicity at Junction Gold Mine became a serious operational problem in the late-1990s. Assessing the local seismic hazard is an important step in assessing the risk associated with potential rockbursting. This paper discusses the qualitative and quantitative means of assessing seismic hazard used at Junction. In qualitative hazard assessment, the role of the primary factors contributing to mining-induced seismicity and rockbursting are identified. These factors include: rock mass properties, geological structures, mine development, and stoping. A qualitative seismic hazard map has been developed considering these factors. In quantitative hazard assessment, seismic source parameters from an Integrated Seismic System are used to assess seismic hazard. The seismic source parameters found to be relevant to seismic hazard assessment at Junction are discussed.

Jan 1, 2002

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By H von Blottnitz, A C. Keith

The influence of the life of a mine extends beyond its immediate vicinity both in geographic and temporal terms. Decisions around mine approvals are generally made based on economics, for the mine owner and immediate environmental and social impacts by governments and communities. The value from life-of-mine planning can also be viewed in a holistic frame across the entire value chain from mine to product user. This research examines the Carmichael Coal Mine in light of the holistic benefits and impacts along its value chain from the mine to relieving the lot of energy poor in India.CITATION:Keith, A C and von Blottnitz, H, 2016. Can Australian coal alleviate energy poverty in India – a case study, in Proceedings Life-of-Mine 2016 Conference , pp 52–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By H. Vincent Wallace

ALTHOUGH it is universally accepted that free oxygen is A necessary in a cyanide solution for the dissolution of gold and silver-in accordance with Elsner's equation that 2Au + 4KCN + 0 + H20 = 2KAu (CN), + 2KOH- little has been written and insufficient attention paid to the drop in extraction due apparently to loss of dissolved oxygen in mill solutions. Aeration or oxygenation of cyanide solutions has been more or less successfully accomplished by various types of agitators such as the Dorr (with or without air lifts), Pachuca tanks and more recently "Turbo-mixers" and Denver "Super- agitators"; also by the introduction of chemical oxidizing agents such as Solozone (Na,O,) . At the Wright-Hargreaves and other mines in the Kirkland Lake camp, the introduction of this reagent at the rate of about 1.25 oz. per ton of ore applied to the feed of the ball mills has certainly been beneficial.

Jan 1, 1932