Search Documents

By John E. Miller

Absolute viscosity values for gases usually are determined with a capillary tube viscosimeter, One of the correction factors applied to the experimental data is that for nonuniformity of the capillary bore. This report contains useful analytic expressions of the nonuniformity correction for the following cases: ellipse, cone, sine wave, sawtooth wave, square wave, and the general case. The methods herein described are applied to estimate the nonuniformity of a section of stainless steel capillary tubing to be used at the Bureau of Mines Helium Research Center. Several other examples are given to illustrate the usefulness of the present results.

Jan 1, 1967

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986

By M. L. F. Paullo, S. Cristian Mejia, D. Roehl

"Rock fracture simulation most often presents non-linear behaviour due to loss of material integrity and strain concentration in the fracture zone. These strains generate local instabilities that propagate to the global system of equilibrium equations, generating convergence problems of the numerical solution. Often, in such cases, analyses in the post-critical regime are unfeasible. To overcome the numerical difficulties associated with problems of stiffness loss in the post-critical regime control methods, also called continuation methods, are employed. Among them are the arc-length method, the energy control method and the indirect displacement control method. These methods are employed in conjunction with a Newton- Raphson scheme for the solution of non-linear systems of equations. However, depending on the system instability, convergence in not guaranteed even with very small increments. In the present work these control techniques are investigated in combination with cohesive elements to simulate rock fracture. The constitutive model employed with the cohesive elements represents stiffness degradation through a damage law, which leads to serious convergence difficulties as reported in the literature. Here the continuation methods mentioned are applied to a Mode I rock fracture problem and to hydraulic fracture simulations. The effectiveness of the different continuation methods is compared.INTRODUCTIONThe process of rock fracture induced by the fluid pressure is called hydraulic fracturing. The propagation of a hydraulic fracture is a complex process, which is basically defined by the mechanical deformation of the rock, the fluid flow within the fracture and the fracture propagation itself (Mokryakov, 2011). In the works of Bendezu et al. (2013), Chen (2012) and Carrier et al. (2012), vertical hydraulic fracture propagation is modeled by cohesive elements with traction-separation law. The softening behavior of rock in post-critical regime is demonstrated by experimental testing and is characterized mainly by high strains and low stresses (Crowder and Bawden, 2004). This nonlinear behaviour can arise due to material nonlinearity, such as micro-cracking and damage, leading to softening behaviour (Chandrakant, S.D., 2012). The cohesive fracture model considers in its formulation the softening behaviour that most rocks present in post-critical regime with propagation criteria."

Jan 1, 2015

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilize crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realize reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By R J. Holmes

An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and traded is crucial to effective resource utilisation, plant design, process optimisation and finally quality control to ensure that contract specifications are met. However, all too often the responsibility for sampling is entrusted to managers and personnel who do not fully appreciate the significance and importance of collecting representative samples for analysis, and everyone seems satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. This needs to change, because there is little point in accurately analysing samples if they are not representative in the first place. The resultant analyses can be next to meaningless and the effort taken to analyse such samples is to a large extent a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts. It is high time that sampling is given the attention it deserves as the first critical step in the quality measurement chain.CITATION:Holmes, R J, 2013. The importance of sampling in the mineral industry, in Proceedings MetPlant 2013 , pp 34-49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Annika Gram, Teddy Johansson, Lutfi Ay

Micropiles transfer tension or compression forces as well as cyclic loads into the ground via skin friction. The Self Drilling Micropiles (SDM) can be utilized for permanent applications. The hollow bar simultaneously acts, as drilling rod, injection tube and reinforcement for the micropile. The SDM system can be used in any type of soil, including unstable soils, without the need for temporary casing. Injecting a cement grout through the hollow steel tendon ensures that the borehole is filled from the bottom to the top. The system is fast, simple, and flexible. The installation minimises noise, vibration, and spoil. There are many potential applications, including foundations, underpinning, resisting uplift, dynamic/cyclic load applications and geothermal installations. The SDM technology were introduced to India first time in the Indian history and utilised in the 4G and 5G network projects. The SDM challenge the traditional cast-in-situ piles in the 4G project and raft foundations in the 5G project. Utilisations of the tensile and the compressive strength capacity of SDM with smart solutions results in noticeably big costs, 17-38 % depending on the soil conditions and time savings. The cost of the SDM solutions was about 40% less than the cast-in-situ piles and raft foundations in an ongoing 5G project. The SDM were used successfully in the liquefiable soil types as well.

Nov 1, 2022

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By Upfold RW, Velzeboer MD

An underground mine fire will influence the ventilation equilibrium in several ways which results in a redistribution of the ventilating quantities and pressures throughout the whole mine. The ventilation carries the combustion products which constitute the greatest danger of mine fires through the mine and provides the oxygen on which the intensity of the fire depends. However, as a result of the ventilat- ion disturbances created by the fire, changes in airflow patterns can take place which are not always obvious, especially when the mine is being served by several fans. The use of com- puter simulation techniques allow for the likely effects to be tested and the different ventilation options to be evaluated as an integral part of the overall emergency/rescue planning and control procedures.

Jan 1, 1981

Collecting the clay fraction of active stream sediment from a flowing stream for geochemical analysis i a difficult process. One either takes a sample of dry fine-grained sediment from the stream bank (dry weather and dry sample are uncommon in parts of New Zealand and Tasmania), or dredges up a sample of sand and mud out of the stream.The latter method produces a soggy ample bag full of mud and sand, with varying amounts of gravel, depending on the size of the stream. The water can be filtered from such a sample by means of a Buchner filter funnel, but is difficult to obtain a vacuum in the bush. This problem can be solved by using a small hand- queeze bellows such as used in priming petrol pumps on outboard petrol motors. The common laboratory hand bellows is not powerful enough.A 70 mm diameter two-piece polythene Buchner filter funnel (Fig. 1) can be used. A length of rubber tubing is fitted around the inlet valve of the hand bellows and this valve is then jammed into the pipe at the bottom of the filter funnel (the polythene pipe may be trimmed with a knife to fit over the inlet valve of the bellows). The vacuum is generated and maintained by squeezing the hand bellows.The technique of collecting a sample of the clay fraction is to dredge a sample of the fine-grained active stream sediment out of the stream with a container, such as a plastic mug. The sample is agitated to get the clay fraction into suspension and the muddy suspension is then decanted into the Buchner funnel. The desired clay fraction is obtained as a thin film on the filter paper.If the "fines" are also required, a filter of nylon bolting cloth (stretched across the mouth of a short length of 80 mm diameter polythene pipe and attached by rubber bands or a concentric polythene pipe) can be placed over the mouth of the Buchner funnel and the whole sample of stream sediment...

Jan 1, 1969

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By I. C. Spangenberg

The status of sampling practices in the gold mining industry in Africa was determined as an initial step in a process to standardize sampling practices in the mining industry. Twenty-one gold mines, twenty metallurgical plants, and thirteen laboratories were rated for the potential influence of the relevant sampling errors on each component of the particular sampling system. The findings of the study on the status of equipment, standards, procedures, and management principles were presented in a dissertation (Spangenberg, 20121) and are now used by AngloGold Ashanti?s mines in the quest for correct sampling practices. The information is also used to compile a guideline on leading practice procedures for sampling methods in gold mining. This article is an overview of sampling best practice found in African mining Keywords theory of sampling, best practise, sampling errors, sampling standards.

Jan 1, 2014

By Ron Glowe

This paper shows the potential of a new computer model, using the Glowe-Tech (GT) Tonnage Analyzer program to compare drilling and blasting results. This model uses the crushers and conveyors as measuring tools in aggregate quarries in the USA and Canada. All data is collected using commercially available kilowatt transducers and an analog input/output automation module. There are two areas of measurement used to compare results. The first area is the tonnage moved by key conveyors to show the split in products produced and the actual rate of production. If belt scale readings are not available then the Glowe-Tech Tonnage Analyzer can be used to convert kilowatts from the conveyor motor to tonnage. The second is the tons of rock crushed per kilowatt hour of energy consumption by the primary and secondary (optional) crushers. This modeling process works best if blasts are mucked and crushed in sequence. There are many other variables such as crusher types, crusher settings, screen sizing and actual geology in the pit that can influence the results, however if variables can be standardized then definite trends can be seen when comparing drilling and blasting results

Jan 1, 2005

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By T. G. Joseph, M. Bolster, M. Curley

"High tirerim loading on haul trucks operating on rough ground frequently manifests as mechanical separations and rim base cracking caused by cyclic fatigue. This paper provides an understanding of the impact of high loads on rim component life and tire footprint, bulge, and deformation behaviour; and develops a maintenance planning tool to predict strain implications of high g loading for a given rim location. Loading tests and analyses were conducted for a tirerim arrangement under increasing load and internal tire pressure. Graphical models were developed, allowing higher g load extrapolation predictions for specific rim components.KEYWORDS g load, Mining, Model, Prediction, Rim, Strain, Tire bulge, Tire footprint, Ultra-class vehicleRÉSUMÉ L’application d’un chargement élevé sur le système pneu/jante de camions de transport rou¬lant sur des terrains accidentés se manifeste fréquemment par des séparations mécaniques et une fissure à la base de la jante engendrée par une fatigue cyclique. Cet article nous permet de mieux comprendre l’incidence de l’application de charges élevées sur la durée de vie des composantes de la jante ainsi que sur l’empreinte, la hernie et le comportement de déformation des pneus. Il développe également un outil de planification de l’entretien visant à prévoir l’incidence des contraintes en cas d’application d’un chargement g élevé sur un endroit donné de la jante. Des essais et des analyses de la charge ont été effectués pour un agencement pneu/jante soumis à une charge et une pression interne du pneu croissantes. Des modèles graphiques ont été développés, ce qui a permis d’établir des prédictions sur la base d’une extrapolation du chargement g plus élevé appliqué à des composantes spécifiques de la jante.MOTS CLÉS charge g, contrainte, empreinte du pneu, exploitation minière, hernie du pneu, jante, modèle, prédiction, véhicule ultralourdINTRODUCTION The purpose of this paper is to report on a proposed and trialed tire performance test based on data obtained from controlled testing that is used to predict the impact of high g loading on hauler rims and tires with greater accuracy. For example, for many years oil sand mining operations have expressed qualitative beliefs that an impact load of the magnitude experienced by a rim and tire arrangement is not detrimental to a rim as a stiff component; however, mining equipment components are subjected to cyclic loading where failure can result from repeated load/unload activity, truncating the peak region of a stress–strain response and resulting in fatigue failure at a stress value that is less than the peak value. The outcome reported by oil sand haul truck maintenance groups indicates they have realized that most high g impacts—such as those experienced by hauler tires and rims operating on poor ground conditions—can result in failure due to cyclic loading, where higher loads require fewer cycles for failure. This high-level loading and the resulting strain transmitted to the rim is evident in the results of the laboratory testing presented in this paper."

Jan 1, 2019

By M. M. Fine

Research on the solid-fuel reduction of Knob Lake iron or was conducted to upgrade lean and high-grade ores and recover metallized products suitable for ironmaking or steelmaking. The program included bench-scale tests plus a number of continuous campaigns in a 34-inch by 36-foot rotary kiln. In the laboratory, metallizations in excess of 90 percent were achieved by reduction of crushed ore with lignite at 950° C. Subsequent grinding (to minus 200 mesh) and wet magnetic separation yielded concentrates analyzing less than 3.0 percent SiO2 and more than 90 percent Fe. Virtually complete recovery of the iron occurred. During early continuous tests the crushed ore created a serious ringing in the kiln which was solved by balling the fines with bentonite. Unfortunately, at this temperature (950° C) the bentonite militates against the concentratability of the metallized product. For example, a run on direct-shipping ore produced concentrates of 89.5 percent Fe and 4.5 percent SiO2. At 500° C the adverse effect of bentonite disappeared and concentrates of 88.4 Fe and only 2.5 percent SiO2 resulted. However, with comparable feed r Los, the metallization dropped to 73 percent.

Jan 1, 1969

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By Charles Steed

The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.

Jan 1, 2003

By M. C. Ruiz, M. E. Godoy, J. B. Rivarola, M. W. Ojeda

The amount of Pd recovered from an exhausted olefin hydrogenation catalyst was found to depend on mixing technique, particle size, carbon percentage, chlorine flow, reaction time and temperature. Pd extraction was total when a sample in the 125-175 micrometre particle size range was chlorinated for 60 min at 723 K with 20 cm3 Cl2/min, for 60 min at 748 K with 30 cm3 Cl2/min and for 30 min at 773 K with 30 cm3 Cl2/min. No C addition was needed; the initial C content of the catalyst was sufficient for total recovery. Pd extraction was also affected by heat treatment in different atmospheres before chlorination. Treatment with O2, N2 and N2 with traces of O2 led to different degrees of oxidation of C and permitted the formation of oxidised Pd species. Thermal pretreatment in N2 with traces of O2 was most conducive to Pd extraction

Jun 21, 1905

By Bernard S. Covino

The Bureau of Mines is conducting a study of methods to improve the efficiency of the process used to pickle stainless steels. A review of the literature on pickling of stainless steels showed that the chemistry of several process operations involved in the pickling of stainless steels is not fully understood, and that further research could improve the pickling efficiency. The benefits of this research would be a reduction in the annual loss of several thousands of tons of critical minerals such as nickel and chromium, and a reduction in the amount of solids and spent acid solution that are currently discarded. The conclusion from this review is that further research is needed in four operations that either directly or indirectly influence the pickling process: hot working, annealing, conditioning, and the actual operation of pickling, Laboratory studies of the pickling operation are presently in progress.

Jan 1, 1984

By J Cronin, R Burgess-Limerick, T Horberry, L Steiner

"Automation offers the mining industry great potential for improvements in productivity and safety. However, the experience of introducing automation in other industries has been that the full potential of new technology is not always realised. Designers are surprised, for example, to find that automation does not eliminate human errors. Unwanted and unexpected consequences also arise if the introduction of automation fails to consider how people will adapt to the new technology. A focus on the technical aspects of automation is necessary but not sufficient for success. The potential for improvements in productivity and safety promised by automation will only be achieved if the joint cognitive system that emerges from the combination of humans and automation is designed to perform the functions required for system success. This case study describes the human factors issues associated with the introduction of automation generally, and describes a case study of the successful implementation of loader automation at Northparkes mine.Information obtained through a site visit and interviews with operators, safety staff and the project manager revealed the following strategies for successful design and implementation of the automation system: involve the people who will be impacted encourage constant communication between operators and designers provide operators with essential information avoid providing non-essential information provide the operators with flexibility empower operators to take action take advantage of the new possibilities automation provides.CITATION:Burgess-Limerick, R, Horberry, T, Steiner, L and Cronin, J, 2017. Mining automation human-systems integration – CMOC-Northparkes case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 93–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017