Search Documents

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By K. Zipf, Z. T. Bieniawski

"An extensive mixed-mode fracture toughness testing programme was conducted on coal from three coal fields. A special mixed-mode testing fixture for coal and other geologic materials was developed together with reliable specimen preparation procedures. Dynamic modulus measurements made on each of the 116 fracture toughness specimens showed that these coals exhibit certain degrees of anisotropy. The fracture toughness testing programme systematically varied the loading rate, specimen orientation and fracture loading mode. Loading rate did not significantly effect the fracture toughness over the quasi-static range tested. Orientation did have a significant effect on measured fracture toughness. In the coals tested, the divider orientation and arrester orientation had higher fracture toughness than the short transverse orientation. Data showed that one orientation could have almost twice the fracture toughness as another. The fracture toughness testing enabled certain evaluations of three mixed-mode fracture theories: maximum tangential stress, maximum energy release rate and strain energy density theory. Due to the extreme heterogeneity of the coals tested, definitive conclusions regarding the best mixed-mode fracture theory are not possible; however, data do tend to support the strain energy density theory. INTRODUCTIONThe major aim of this research is to ·develop a fundamental understanding of how fine· fragments of coal (respirable dust) are generated during a fracture process. In a related paper [l], a hypothesis was presented for the mechanism of fine fragment formation during a generic coal material/cutting tool interaction. In this hypothesis, fine fragments are created during coal material/cutting tool interactions that are best described as general mixed-mode fracture processes. Data are required on the mixed-mode fracture behaviour of coal, the physical character of the newly-created fracture surfaces and the character of the inherent flaw structure of the coal material. Accordingly, a test programme was designed that provided some information in each of these areas. The testing effort seeks to measure critical fracture toughness under mixed-mode loadings as a material parameter characterizing in part the tendency of various coals to generate undesirable quantities of fines and respirable dust."

Jan 1, 1990

By James R. McVey

Tests during pillar robbing, longwall operations, and other mining activities indicate that roof-floor convergence rates can be used as an indicator of imminent roof failure. A large number of electrical-mechanical devices have been built to measure convergence as well as convergence rates, but most obstruct mine traffic and are costly and time consuming to install. The Bureau of Mines has designed and is evaluating three types of small ultrasonic units to make these measurements. The new instruments provide nonobstructing measurements up to 35 ft away. The ultrasonic transducers can be attached to a roof bolt, placed in an unsupported area (by means of a toss basket), or handheld. Total distance to the target and rate of closure are displayed digitally to 0.001 ft and 0.01 ft/min, respectively.

Jan 1, 1984

By J. N. Van der Merwe

The paper provides an overview of subsidence research which was done by the Sasol Company in South Africa over a period of more than six years. The magnitudes of subsidence elements in South Africa are largely similar to those in the U.S.A. and Australia, as opposed to Europe. The research resulted in a subsidence prediction method with a new approach to the prediction of ground strain. The paper also describes the effects of subsidence on various commonly occurring surface structures such as roads, overland conveyor belts, pipe lines and power pylons. It is concluded that while most structures are not specifically designed to accommodate mining induced displacements, they can nontheless be undermined safely and economically with only minor precautions.

Jan 1, 1986

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Southern field is part of the comprehensive study of the mine water problem in the anthracite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8, 9, 10, 11, 12, 15, 16, 18).4 Tim Southern field is in Carbon, Schuylkill, Dauphin, and Lebanon Counties, in eastern Pennsylvania; has an area of 200 square miles; is 70 miles long from Mauch Chunk on the east to the Susquehanna River on the west; and is 1 to 6 miles wide. In the Southern field are 37 underground water pools containing 37312 billion gallons of water (5). Most of these pools overflow to the surface because the barrier pillars controlling them are effective under existent, conditions. Abandonment of mines in the Southern field has resulted in the hooding of 34 percent of the field. The largest tonnage of reserves of anthracite lies in this field, where mining conditions are most difficult. Large reserves of anthra¬cite underlie the abandoned mine workings, and before a great part of these reserves can be developed and extracted, the abandoned workings must be unwatered and kept drained (5).

Jan 1, 1953

By David Sutherland

The treatment of a complex orebody requires a thorough understanding of its mineralogy. If there is a poor appreciation of the mineralogy involved, difficulties can emerge with the efficient exploitation of the resource. Recently, there has been a lot of interest in automated image analysis systems, which aim to improve the reliability and accuracy of the data, which can be gathered. In this sense, the paper point out the process mineraloggy for complex ores. Mineral modal analysis a description of texture and liberation studies are the basis of these measurements. They have been applied to a wide range of mineral systems including copper, lead, zinc, silver and gold.

Sep 13, 2001

By Garry M. Hughes

Lynn lake, Manitoha, where Sherritt has operated a copper-nickel mine since 1954, is located north of the 56th parallel approximately SOO miles north of Winnipeg. Sherritt's new, 3,000 tpd, copper-zinc Fox Mine is situated 30 miles southwest of Lynn lake. This paper focuses on the Fox Mine concentrator, hut first some background information. Sherritt Gordon Mines Limited started mining operations as a copper-zinc producer in 1931 at Sherridon, Manitoba, 150 miles south of Lynn Lake. As Sherridon fizzled out development of a series of nickel-copper orebodies commenced at Lynn Lake. The Forward process was developed to treat the nickel concentrate from the Lynn concentrator. Sherritt's ammonia leaching process is now history and is expected to gain more prominence as pressure is applied to the mining industry for closer environmental control. But few are aware of the fact that the present Lynn Lake crushing plant and concentrator were dismantled in the autumn of 1951 and freighted from Sherridon by tractor train during the winters of 1952 and 1953. The copper-zinc orehody at Fox Mine was discovered early in 1961 by geophysical methods which included both airborne and ground surveys. It is part of a ,large body of massive and semi-massive sulphides consisting chiefly of pyrite; with chalcopyrite, sphalerite (containing 7-9% iron) and pyrrhotite in varying proportions which occur within a series of volcanic and sedimentary rocks. The total mineralized zone is a lenticular body with a minimum average length and width of 1,350 feet and 66 feet respectively, to the explored depth of 2,000 feet. The average sulphide content is 67%. Higher zinc zones are masses of pyrite grains cemented by sphalerite with lower than average copper content. Zones higher in copper and lower in zinc are slightly more quartzose. Gold and silver are present in small amounts roughly proportional to the copper content.

Jan 1, 1971

By Dieter Loh, Mathias Knoll, Florian Werres

When a new tunnelling project starts, it has been a vital tradition for decades to cast and erect master rings horizontally on a flat surface to demonstrate the compliance with dimensional tolerances. Some tenders ask for the erection of two or even three rings upon each other or repeated master ring erections at intervals throughout the project. Especially for large diameters, this is a challenging and risky task for the workforce in the segment factory. A truck-mounted crane is often necessary, and in some cases it can take up to a week to complete a master ring. The concept of virtual rings has the potential to replace this tradition by assembling master rings digitally instead of physically. This is based on a best-fit approach, considering the 3D coordinates from laser tracker measurements of segments or segment moulds. Building a virtual ring, a sub-millimeter accuracy can be achieved, the alignment of neighboring circumferential and ring joints observed, and the fit of bolt holes checked. The traditional method, on the other hand, is discussed controversially despite the significant amount of work and risks—particularly as the horizontal position of the ring and absence of gaskets do not simulate the reality in the excavated tunnel. This paper will highlight the technical aspects of virtual rings, as well as their pros and cons, illustrated by a case study from London Thames Tideway where a total of 30 physical master rings could be replaced by virtual rings.

Jun 13, 2023

By Robert McIvor

The following is a summary of the Robert H. Richards Lecture on “Learning and Good Fortune on the Road to Discovery” presented at the Mineral & Metallurgical Processing Division (MPD) Awards Plenary Session on Feb. 23, 2026 during the MINEXCHANGE 2026 SME Annual Conference & Expo in Salt Lake City, UT.

Mar 1, 2026

By M. Potesser

Higher prices for natural gas or oil have motivated the copper industry to reexamine the modes of oxygen and oxy-fuel burner usage at operating plants. With rising energy costs and the growing importance of environmental protection, burner usage and burner operations have become the focus of several investigations and optimization efforts. One possible approach to lower energy usage is through combustion using tonnage oxygen. When such oxygen is used, the flame temperature increases and operational efficiency is improved. As well, with the correct technology, due to the presence of lower levels of harmful substances such as NOx in the off gas, there is improved environmental performance. As regards copper production, furnaces are employed for both concentrate smelting or for melting and casting operations. The use of tonnage oxygen in concentrate burners for smelting provides for a higher thermal efficiency. For furnaces employed for melting, air-operated burners may in fact have an initial advantage because a long radiant flame is typically generated, thus providing for a higher degree of heat transmission. This paper describes the new experimental burner chamber of Messer Austria GmbH which provides for testing of the combustion of natural gas with oxygen or oxygen-enriched air and the use of special water cooling ducts that simulates a metal charge during melting, The operational effectiveness of the burner is determined from temperature and off-gas analysis data. The paper also discusses future trends in burner technologies including a new patented burner. Cu2007 - Volume III (Book 2) The Carlos Diaz Symposium ou Pyrometallurgy Edited by A.E.M. Warner, C.J. Newman, A. Vahed, D.B. George, P.J. Mackey, A. Warczok Toronto, Canada,

Jan 1, 2007

By Robert M. Vadas

Special considerations are described as they apply to the design of ring gears for high-power grinding mills. AGMA requirements, the importance of the supporting structure, material selection and related field experience are discussed, with special emphasis on available and developing manufacturing technologies.

Jan 1, 1978

By Shuji Owada

Scrap electrical and electronic appliances, so called "E-waste", are not a present target to be collected and recycled under Japanese regulations. This material, however, contains considerable amounts of base, precious, and rare metals and it is necessary to recover these elements for maintaining stable supply and establishing "the society of environmentally-sound material-cycle". This paper describes recent trends of rare metals recycling in Japan and technological approaches to achieve the above objective. Also a research work to concentrate rare metals from the printed wiring boards by combining brand new comminution and physical separation methods is discussed.

Jan 1, 2011

Just as geophysics, in the form of 3D seismic and wireline logging, plays a key role in petroleum reservoir management, so too will geophysics play an important role in mining of coal, metals, and minerals in the 21 st century. The commercial and social imperatives driving greater use of geophysics are reduced costs, increased revenues, and enhanced safety. In short, superior utilisation of capital and management of risks. In relatively undeformed sedimentary environments it is possible to adapt petroleum-style 3D reflection seismic to image mines. This has been demonstrated most impressively in the Witwatersrand. Anglo-American, for example, completed a $1 million 3D seismic survey at Western Deeps in order to site a new $300 million shaft with confidence. Likewise, 3D seismic has gained rapid acceptance at Australian coal mines in recent years. Encouraged by these successes, metalliferous mining companies are supporting research in Canada and Australia, as well as South Africa, to adapt 3D seismic for more highly structured, metamorphic terranes. Because the mining industry is far more diverse than the petroleum industry in terms of commodities and geological environments, 3D seismic is not always cost-effective. A plethora of other geophysical techniques can be applied, many of which are employed in mineral exploration. Mine applications of geophysics differ from traditional exploration applications in two main ways: time scales and length scales are shorter, and boreholes are more plentiful. Borehole geophysical techniques therefore play a more significant role, both for logging and imaging. Logging systems detail the variations of in situ physical properties down the borehole at scales measured in centimetres, while geophysical imaging techniques can map features located tens or even hundreds of metres from the sensors. While geologists tend to think of boreholes in terms of chips and core, geophysicists perceive them first and foremost as access paths for instruments. Borehole logging has been employed at iron and coal mines for decades, mainly to accurately define ore boundaries in delineation holes. In base metal mines, Outokumpu implemented logging widely for orebody delineation in percussion holes in the 1980s. The benefit was a direct cost-saving, arising from substitution of core drilling with percussion drilling plus borehole logging. The practice has since spread to other companies. INCO, for example, defines nickel boundaries in blast holes at Sudbury using conductivity logs. The benefits are in the form of reduced dilution and enhanced ore recovery, flowing from a more accurate mine model. Density, natural gamma radiation, magnetic susceptibility, and conductivity are the principal metalliferous mine logging parameters because they can be recorded in both dry and water-filled holes. Sonic velocity is the premier geotechnical logging parameter, given its sensitivity to rock strength, stress, porosity, and degree of fracturing. Sonic is recorded routinely in exploration and geotechnical holes at coal mines. With the advent of slimline dipmeter, full waveform sonic, and optical and acoustic scanner tools, the role of borehole logging in geotechnical evaluations is expanding. Monitoring of strain and micro-seismic activity enhances safety during mine production. While qualitative interpretation of logs is adequate for stratigraphic identification or definition of boundaries, a wealth of quantitative information, eg density, can be derived from properly calibrated, repeatable geophysical logs. Moreover, geophysical logs can sometimes serve as surrogates for geochemical assays, and not only for magnetite and uranium. At OutokumpuÆs Kemi chromite mine, for example, gamma-gamma logging provides the basis for grade control. By reducing reliance on assaying, three benefits can be realised: reduced reliance on core drilling; lower core handling and assaying costs; and shorter turn-around times. Conventional downhole EM and borehole magnetics are used for near-mine exploration, and for ground sterilisation. Inco has enjoyed considerable success with borehole UTEM in the Sudbury Basin, for example, and Geopeko has applied three-component borehole magnetics successfully in the Tennant Creek area. Electrical techniques such as applied potential and magnetometric resistivity (MMR) are also finding application at mines. For higher resolution, borehole seismic, radio imaging, and radar have been invoked, with varying degrees of success, to delineate orebodies and map structures, or to geotechnically characterise the rock mass and identify hazards. Success mapping nickel sulphide shoots with borehole radar has been reported by WMC at Kambalda. There are no universal geophysical panaceas, and each mine imposes different geological, logistical, and economic constraints. Geophysics will not always be cost-effective. However, the greatest single impediment to expanded use of geophysics at mines has been the low level of awareness of geophysics on the part of most mine geologists, engineers, and managers and, equally, the limited understanding of mine geology and engineering exhibited by the majority of geophysicists. This myopia will be remembered as a 20th century affliction! Blue Sky areas for mine geophysics in the next ten years include integration of geophysical data acquisition with drilling, enhanced grade estimation and rock mass characterisation, and the incorporation of geophysical information into mine models using geostatistical techniques. All these advances will be predicated on an expansion of petrophysical knowledge.

Jan 1, 2000

By Donald M. Ulbrich

Any of you who served in the military remember the admoniton to "get the lead out," In the military environment, where cost wasn't always a factor, "get the lead out" was more often a call for activity of any sort than activity of a particularly productive nature. As a result, when the top sergeant yelled "get the lead out," lots of people started moving.. . usually to get out of his way. Now there's a new cry, ..one that comes not only from the military but from an entire nation threatened with dependence on foreign sources for its energy needs. That cry ...get the coal out, Like the earlier order, it's a call to activity. A signal that the coal reserves of the United States must be tapped so that Project Independence can succeed by 1985, But it's more than a mere call to activity; it's also a call to achieve productivity. ,a call to produce coal both efficiently and acceptably. And that leads us to the key questions of where the coal is going to come from to meet that 1985 goal, and how can it best be mined. Where will the coal come from? There's no doubt much of it must come from surface mining in the West. How can this coal be mined? There are several options available but there is an excellent case to be made for using mining shovels and haul trucks due to their versatility in stripping, loading and reclamation, We'll explore this approach in this talk today.

Jan 1, 1976

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Determination of the thermodynamic properties of metallurgically important compounds of chromium has been one of the activities of the Pacific Experiment Station of the Bureau of Mines. Earlier reports have dealt with the entropies 4/ 5/ of chromium, chromic oxide, and chromous and chromic chlorides, with the thermodynamic properties of the chlorides of chromium, 6/ and wits the thermodynamic properties of the carbides and oxide of chromium. 7/ Evaluation of the thermodynamic properties of chromite, FeO.Cr2O3, is desirable, as this material in impure form constitutes the only natural source of chromium of any consequence.Two general methods are available for directly determining heats of formation - (1) measurement of heats of combustion and (2) measurement of heats of solution. Neither of these methods is directly applicable at present to ferrous chromite, which accounts for the lack of previous data. Combustion of a stoichiometrical mixture of iron and chromium under conditions prevailing in a calorimetric bomb yields a mixture of iron and chromium oxides rather than chromite. None of the usual calorimetric solution media dissolve chromite at temperatures low enough for solution calorimetry. Sulfuric acid and an oxidizing agent, such as MnO2 or CrO3, are known to dissolve chromite, but the possible calorimetric use of t is medium would require long preliminary investigation. Consequently, recourse must be taken to some indirect method. At the start of the present work, the most promising method appeared to be the determination of equilibria in the selective, reduction of the iron in chromite by hydrogen;"

Jun 1, 1945

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

Auger operations produced 14 million tons of coal in 1974, or approximately 5% of all surface mined coal. It was the most efficient of all coal mining methods, producing 40.0 tons per man-day. Exhibit 1.1 gives a breakdown of productivity of all coal mining methods. Exhibit 161 PRODUCTIVITY OF COAL MINING METHODS (Short tons per man-day) [Method - 1971 1972 1973 1974 Conventional 11.00 10.00 9.75 9.30 Continuous 13.00 12.50 12.25 11.90 Strip Mines 35.69 35.95 36.00 36.00 Auger Mines 39.00 43.00 45.33 40.00 ] Unlike other surface mining methods, augering produces clean coal, largely uncontaminated by foreign materials, other than those existing in the coal seam itself. However, compared to other methods, the coal recovery rate is relatively low. For example, a triple-headed auger in a 35-inch seam would recover approximately 50% of the coal in the seam as compared to a 90 to 95% recovery rate for strip mining and a 55 to 65% recovery rate for deep-mining. The low auger recovery rate is due to the circular cuts and pillars left in the seam.

Jan 1, 1975

By C K. McKenzie, P Popov, B E. Papillon, I Kharitonenko

Flyrock produced by blasts in surface mining and quarrying is a major hazard that can result in serious injuries or property damage. This paper presents a fully integrated and automated approach for reviewing blast outcomes from a wide variety of rock blasting environments from the perspective of flyrock safety associated with blasthole collar ejections. The process is applied at a corporate level for an explosives service provider handling up to 100 blasts per day from mines, quarries and construction sites throughout the US.Flyrock risk minimisation has inspired research and the associated development of a reliable flyrock model to estimate flyrock ejection velocities and the resulting maximum projection distances of fragments. In spite of significant achievements in this area, flyrock incidents continue to occur, mostly due to implementation mistakes. An efficient preventive measure is continuous blasting process improvement that relies on on-site video recording, storage, automatic analysis and classification of the recorded blasts followed by the automatic generation of reports.In this paper, a novel blasting video analysis system that is capable of processing a large quantity of video records is presented. Blast analysis and parameter measurement are fully automated and are carried out using videos recorded with a conventional consumer camera. The blast video recording process does not require the use of surface markers, range poles or objects of a predefined size for scaling purposes.Although automatic video analysis is commonly used in many application areas, such as video surveillance, traffic monitoring and robotics, the algorithms that have been developed to recognise and track solid objects with well-defined shapes, textures and colours are not efficient at dealing with blasts, which, by their nature, have dynamically changing parameters. Moreover, very strong camera vibration caused by blasts that cannot be totally compensated by camera image stabilisers may cause conventional computer vision algorithms to fail.This paper presents novel computer vision methods developed for automatic tracking of the trajectory from a blast ejection point to the highest point reached by blast particles and the ejection velocity. The system also uses colour and motion analysis to detect the emission of toxic fumes during a blast. The solution is vibration tolerant and can differentiate foreground and background data, even in the presence of camera vibration. Moreover, the blasting video analysis method can automatically categorise correctness of the measurements and therefore indicate cases when additional visual inspections may be required to verify reports generated automatically.CITATION:Kharitonenko, I, McKenzie, C K, Papillon, B E and Popov, P, 2015. An automated system for flyrock and fume monitoring of blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H. E. Frimmel

Abstract - Most of the gold in the Late Archean Witwatersrand Basin is of detrital origin but, in its present form, it is metamorphosed. The only relict detrital features preserved are the morpho­logical characteristics of some placer gold particles. Regional burial metamorphism in the shallower and deeper levels of the Witwatersrand Supergroup reached temperatures around 300°C and 350°C at pressures between 2 kbar and 3 kbar, respectively , estimated from phase relations, chlorite-chloritoid exchange thermometry and chlorite thermometry . Metamorphism of the gold involved compositional homogenization of individual gold particles and partial recrystallization. Various infiltration events caused the partial mobilization of the gold at slightly lower temperatures, between 240°C and 300°C. These infiltrations can be related to crustal extension during the deposition of massive carbonate sequences of the Transvaal Supergroup (around 2.5 Ga), and later to the emplacement of the Bushveld Complex, and to the Vredefort event around 2.0 Ga ago. The mobility of the gold was dependent on the sulfur fugacity prevailing in a particular horizon which, in turn, was deter­ mined by the amount of pyrite (and other sulfides) present in that horizon. With the sulfur fugacity being controlled by stratigraphy, low fluid:rock ratios in a pyrite-rich horizon were most conducive for the mobilization of the gold. Thus, long-range gold mobilization in the Witwatersrand Basin can be expected to be the exception rather than the rule.

Jan 1, 1994