Search Documents

George E. Collins, Nacoochee, Ga. (communication to the Secretary): The results tabulated below were obtained at the Reynolds mill, White county, Ga. They were noted, not with a view to investigating the point discussed by Mr. Clark, but in course of a test on a working scale to determine the com parative saving from a given free-milling ore on copper and silvered plates respectively. In every case the bullion assayed was the result of a separate clean-up on a considerable quantity of ore. The ore varied widely in grade and in other respects, but the runs bracketed in the table were made at the same time, in adjoining batteries, and on similar types of ore. In a * Result modified by the addition to the bullion-shipment of a little impure bullion left over from previous clean-ups.. On these occasions, the strips of copper were removed from the tables, and: their lower surfaces were cleaned. Hence the higher yield reported.

Jan 1, 1900

By Ehsan Alavi, Brian Hagan, Colin LaVassar, Glen Frank, Derek Dugan, Rick Capka, Lisa Mori

"Tunnel face instability is one of the most common issues in EPB tunneling. The evaluation of an ideal face support pressure is a critical element in the design and construction phases of EPB tunneling. In this study, measured tunnel face pressures in three EPB tunneling projects (University Link U230 and U220 projects and the Northgate Link Extension N125 Project) for Sound Transit in Seattle, WA are compared with the calculated analytical methods. This comparison shows that the analytical methods generally overestimate the required tunnel face support. The best practice for managing the face pressure in EPB tunneling operation is discussed based on the experience gained through these projects. Furthermore, the algorithm that is developed for identifying ground loss in these projects is addressed. INTRODUCTION Earth pressure balanced tunneling relies on using muck within the chamber to support the face. Muck is pressurized by controlling the advance rate of the tunnel boring machine and the speed of the screw conveyor. Target face pressure is typically calculated by using the geotechnical assumptions in the geotechnical baseline report. The concept behind EPB tunneling is that the application of sufficient face support pressure will prevent tunnel face instability and the resultant over excavation. Tunnel face instabilities caused by a lack of sufficient face support can lead to ground loss and surface settlement (Anagnostou & Kovári 1996, Kirsch 2010). A certain support pressure must be achieved to counteract water and earth pressure with an adequate factor of safety. While the water pressure can be predicted accurately, the determination of the resultant earth pressure on the face is less precise. This becomes manifested in the relatively high partial safety factors on the earth pressure."

Jan 1, 2016

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By W. B. Clark

IN OPERATING the Alpha mine of the Consolidated Coppermines Corp., Kimberly, Nev., it was necessary to pump out approximately 1200 gallons of waiter per minute to prevent the mine being flooded. There were three levels in the mine at which water accumulated and from which it was pumped, the 1200, 1400 and the 1800- ft. levels. At each, the pumping equipment was installed in duplicate so that if for any reason one unit was out of commission the other would be available to prevent flooding. The two centrifugal pumps at the 1200-ft. level were 600 hp. each; at the 1400-ft. level, 100 hp. each; and at the 1800-ft. level, 300 hp. each.

Jan 1, 1933

By E. E. Creitz

Application of the usual chemical methods to the determination of beryllium in the mineral-dressing products of a spodumene pegmatite was found to be unsatisfactory as to speed, accuracy, sensitivity, and range of analysis. A spectrographic method is described for the determination of beryllium. Samples are ground, mixed with borax, high-purity, flake graphite, and an internal standard; then they are fused, reground, pelletized, and excited with a high-voltage-spark discharge. Investigation of several spectrographic techniques to overcome matrix effects are described. The method developed gives results for beryllium in the concentration range from 0.002 to 5.0 percent; the average probable error of duplicate determinations was below 3.0 percent of the quantity present. INTRODUCTION The main source of beryllium in pegmatite is the mineral, beryl. Many of the conventional methods for the determination of beryllium in beryl are not suitable for control purposes because of lack of speed and accuracy, especially in the range below a few tenths percent. Beryl resists the usual chemical attack and can be lost in a hurried chemical analysis.

Jan 1, 1958

By Thiago Vieira Lopes

O mercado siderúrgico atual encontra-se cada vez mais competitivo e exige das empresas esforços na diminuição do custo de produção para que seus produtos mantenham atratividade no cenário global. A incorporação crescente de produtos siderúrgicos oriundos da Ásia no mercado ocidental obriga as indústrias encontrarem alternativas de diminuição de custo de produção, as rotas para que tal objetivo seja alcançado geralmente estão ligadas ao aumento do rendimento metálico e diminuição no tempo de processamento dos produtos. O equipamento gargalo na linha de laminação a quente da CSN, é a cadeira reversível da laminação de desbaste, R2, e pequenas reduções de tempo no processamento de placas são responsáveis por incrementos elevados na produtividade da laminação. Visando ampliar a competitividade da CSN no cenário siderúrgico foi criada uma função, chamada RM-NECK, no modelo matemático do laminador que classifica todos os materiais gargalo desbaste por grau, espessura, largura, número de fornos de reaquecimento e comprimento de placa, permitindo assim, a diminuição no tempo de processamento na zona do VE2/R2. O estudo evoluiu para um verdadeiro trabalho em equipe, envolvendo especialistas da manutenção e operação e, consolidando anos de experiência no desenvolvimento de um algorítmo inteligente o suficiente para reduzir o tempo de processo observando os princípios da teoria das restrições.

Aug 17, 2017

The Elgas Underground Storage Facility at Port Botany, Sydney, is the first purpose-built cavern of its kind in Australia and provides large capacity, safe and environmentally benign storage of Liquefied Petroleum Gas (LPG). The facility will provide Elgas with the flexibility to source product at competitive prices and ensure long-term security of supply. Construction has provided Orica Australia, formerly ICI Explosives, with a unique opportunity to provide a bulk explosive delivery system specifically designed to meet the exacting demands of the site and of the project.

Jan 1, 1999

By W. W. Adams

This bulletin covers all mines in the United States that were operated in 1936 to produce metallic ores and all mines that were operated to produce nonmetallic minerals other than coal, stone, sand, gravel, or their products. Reports from mine operators revealed a better safety record for fatal accidents in 1936 than in any other year except 1934 during the 26 years for which annual surveys of accidents in the mineral industries of the United States have been conducted by the Bureau of Mines. On the other hand, the record for nonfatal injuries, although better in 1936 than in any year prior to 1930, was not as good as it was from 1930 to 1935, inclusive.

Jan 1, 1939

By S. Khan, M. Auret

Due to the modernisation of mines, traditional training methods may be supplemented to support the upskilling of supervisors in mines. A project was initiated by the SAMERDI SATCAP programme to demonstrate the “art of possibility” through a modern training methodology. Two exemplar digital supervisory leadership development modules for underground gold and platinum-group metal conventional and modernising mines, were developed for potential uptake by the mining industry. These exemplar modules were exhibited on a digital platform, towards leading and driving mining modernisation. The research adopted a mixed method approach that included a literature review, a review of an existing supervisory leadership development programme, data gathering, a pilot study, and stakeholder validation workshops. The research supported the development of exemplar digitised modules. The two digitised modules were showcased to the industry for potential adoption. Training slides, a facilitator guide, and a training video were developed for ease of use by industry. The training modules are generic and not specific to a particular mine. They may be used by multi-commodity mines, including gold and platinum-group metals, as ‘stand-alone’ modules. They are customisable, through consultation with relevant service providers for specific working environments. The findings indicated that both the traditional classroom training and the new digitised online learning solution offer advantages for supervisory leadership development. Digital learning is not a new concept for supervisors at mines and modern training methods are well-supported by supervisors in the industry. A ‘modernised’ training solution may consider a ‘blended’ learning approach that combines traditional training with digital methods.

Jun 27, 2025

By James W. Echerd

Anthracite preparation developments, particularly in the early days of the anthracite industry, formed the basis for the modern coal preparation plants that have become so essential to the coal industry today. The anthracite industry, from early in the 19th century until relatively recently, was a leader in mining, preparation and marketing of coal, and played a leading role in the development of the industrial America we know today. Anthracite was discovered in America in about 1760--the story of Necho Allen is well known--but the rediscoveries leading to mining operations took place about 50 years later. The Wurtz brothers in 1815 at Scranton, the Smith brothers at Wilkes-Barre in 1807, Beach in Hazleton in about 1814, and Boyd in 1816 at Shamokin were all instrumental in promoting early mining and marketing of anthracite (J3. The early canals and railroads were built for the specific purpose of moving anthracite to the market areas. Eventually, the industry grew until, in 1917, it reached a production zenith of a little over 100,000,000 tons, representing about 20 percent of the total coal output in the United States. Almost half of the anthracite produced that year was consumed for domestic heating, a utilization that had dominated the industry for almost 100 years. Initially, anthracite had to be used by gunsmiths and blacksmiths, after which had followed the consumption of extensive quantities for railroads, blast furnaces and foundries, and electric power generation. Most of the markets have been lost to coke, oil, and natural gas. Near the anthracite regions, however, significant quantities are still used for domestic heating, power generation, carbon black manufacture, blending with bituminous coal to make metallurgical coke and fuel, and for other industrial purposes. Thus, anthracite production has not been entirely committed to history, but remains an active industry that follows modern practices in the mining, preparation, shipping, and utilization of a fuel that is still a valuable adjunct to the national economy. In fact, its inherent low sulfur content may make it an important fuel of the future. Estimates indicate there are reserves of anthracite to last for 300 years at a consumption rate of 50,000,000 tons/year. Anthracite Preparation Yesterday A 170-year history of the anthracite industry obviously is not the purpose of this discussion. A complete history of anthracite preparation, the rather unglamorous step in the processing of "mine run" hard coal to make it suitable for the user, is also not practical. Hence, the purpose of this report is to trace the development of some of the most important processes used through the years to meet a part of the demand for energy developed by our modern society. Anthracite preparation in the early days of the industry consisted solely of separating slate from the coal, by hand, underground (Z). This method prevailed for almost 20 years until wrought iron hand rakes were introduced to separate the large and small sizes. Shortly thereafter, the first attempts were made to size and clean the coal aboveground. The coal was dumped on a perforated cast iron plate, and men used sledge hammers to break the larger pieces into smaller sizes suitable for the market. The smallest sizes--that is, the material that went through the plate--were thrown away because they had no value at that time--a concept that existed for many years and actually was the basis for the subsequent "river" coal production and the many silt banks which are landmarks in the anthracite region. The larger sizes, at that time, sold for 50 cents per ton. The Batten breaker, or roll crusher, was invented in 1844, followed soon thereafter by the Snell-Diehm breaker (A). The latter had disadvantages, including excessive waste and fixed product size, but it later was improved in these respects. A breaker was also developed at Minersville, Pa., at about the same time that processed 200 tons of coal per day, using roll crushers and circular screens (1). Handpicking, from the beginning of anthracite preparation, was an important part of the cleaning process and was still being practiced as late as 1950. It was this process that involved the "breaker" boys of coal region lore. How much good handpicking accomplished depended on how much impurity was present in the coal--the more the impurities, the greater the reduction in ash. Thus, high-impurity streams were significantly improved, whereas picking of relatively clean coal was mainly to show an effort to make a quality product. As indicated, picking is largely a visual operation. It was and is wasteful of coal in the larger sizes since some good coal is always associated with the bad. However, it was probably much more effective' in the larger than the smaller sizes.

Jan 1, 1971

By G. Kleyn

"Sub-standard practices and their adverse impact on safety performance remain a challenge in the South African gold mining industry. The purpose of this study was to investigate the root causes of sub-standard practices and the effect on safety performance in South African gold mines. The focus of the study was on the underground production operations at a gold mine in the Free State. The study consisted of three parts: a personal investigation into the causes of sub-standard practices at the mine, a comparison with the results of a cultural study performed at the West Wits mines, and a behavioural survey.The studies described in this article yielded similar results in terms of the key drivers behind sub-standard practices. It was found that substandard practices had a number of causes, and the origin lies within the habits, attitude, and behaviour of employees. Current methods of addressing sub-standard practices and improving safety performance were found to discourage employees from performing work safely and according to procedure. It was concluded that the lack of critical behavioural habits for the given work environment and job title could possibly be the primary reason for the occurrence of sub-standard practices. IntroductionSince the implementation of the Mine Health and Safety Act, 1996 (Act 29 of 1996) and the Mine Health and Safety Regulations, the South African mining industry has been striving to improve health and safety performance and has placed great emphasis on adherence to mine standards.The Act requires employers in the mining industry to report accidents, incidents, and dangerous situations to the Regional Principal Inspector of Mines in their area. The data provided by employers is captured and analysed by the South African Mines Reportable Accident Statistical System (SAMRASS) and made available for public viewing (Department of Mineral Resources, 2011).A review of the national mine-related accident statistics shows clearly that the South African gold mining industry has improved its safety performance markedly over the past decade, but is still facing major challenges (Figure 1). These include meeting the Mine Health and Safety Milestones (Department of Mineral Resources, 2011)."

Jan 1, 2016

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By G. Ferrara

The reserves of lead and zinc ores in the metalliferous district of Iglesias in south-western Sardinia are today estimated at about 30 million tons, grading from 4 to 10% Pb + Zn. Of these reserves, about 40% are in the mines owned by AMMI Sarda S.p.A. The working of these resources goes back to ancient times. Not infrequently, traces of old Roman workings and remains of ancient implements are come upon in the higher parts of some of the ore bodies. Exploitation of these mines on larger scale, however, dates from the middle of the 18th century. Initially, the more accessible zones of the ore bodies and the richer ores were worked - the galena and the rich oxidized ores (calamine* with 25-35% Zn), which were often found in large masses, the enormous empty cavities of which still remain. The poorer grade deposits have been gradually rendered workable by the development of technology - the perfecting of the

Jan 1, 1970

Laboratory and pilot plant investigations aimed at recovering gold as an electroformed sheet from gold eluate and gold leach solutions and slurries are discussed. The electrolytic test work undertaken makes use of high surface area electrodes, in particular nickel-chrome foam metal and activated carbon, as well as ultrasonic activation. The process involves initial gold electrowinning (or adsorption onto activated carbon), followed by gold electroforming, both operations being carried out in a specially designed reactor. The pilot plant work mainly involved the treatment of gold eluate solutions from a South African gold mine containing 600 mg/L Au: some tests were also carried out on gold leach solutions containing 6 mg/L Au. In the former case, very efficient gold extraction onto the foam metal cathode was achieved using electrolysis combined with ultrasonics. The polarity of the gold-loaded cathode was then reversed and, using a replacement electroforming electrolyte, gold was electroformed in situ onto a polished stainless steel mandrel, from which gold sheet was subsequently removed. In the case of leach solutions, pilot plant tests confirmed laboratory findings that in the presence of calcium (resulting from the lime used during the leaching process) no electrowinning is possible. Laboratory tests showed, however, that when sodium (in the form of NaOH or Na2CO3) is added to the leach solution, electrowinning can indeed take place. Alternatively, if a special activated carbon electrode is used (without current), the non-ionic calcium aurocyanide complex is adsorbed on to the activated carbon. When a gold-loaded activated carbon electrode is made anodic in a gold electroforming electrolyte, gold electroforming is feasible, although the efficiency is very low. The possible implications of these developments for gold recovery are further examined.

Jan 1, 2007

By Clair Murdock, David Heath

The 1,280 MW Sir Adam Beck II Hydroelectric Project was constructed in the1950s, at Niagara Falls, Ontario, Canada. The twin intake tunnels total over 17 kilometers in length and pass deep below the City of Niagara Falls. The tunnels were excavated using drill and blast methods, with a top heading and bench approach. The shot rock was loaded with electric shovels and transported to the five shafts with off-highway trucks. The tunnel muck was hoisted to the surface by skip and transported by truck to disposal areas. The volume of underground excavation for the 15.55 meter diameter tunnels and the shafts exceeds 3,500,000 cubic meters, then and now the largest underground civil works excavation by drill and blast in the Western Hemisphere. The lining required over 900,000 cubic meters of concrete. All of this work was completed in three years, remarkable progress, considering the technology of the day, comparing very well with the rapid excavation and tunneling methods of the twenty-first century. Big, fast, and deadly—at least 20 lives were lost in construction accidents.

Jan 1, 2007

By P. H. Jennings

Commercial tellurium commonly contains heavy basemetal impurities such as lead, copper, iron, etc., as well as selenium and oxygen. The base metals may be removed by vacuum distillation or by zone melting. Vacuum distillation is a convenient method for treating moderate quantities (~ 100 kg.) for the production of a material having a total content of heavy metals in the 10-30 ppm range. By zone melting, it is possible to lower all the heavy metal impurities tm below the limits of spectrographie detection. Neither vacuum distillation nor zone melting is effective for the removal of selenium, but treatment of molten tellurium with hydrogen converts selenium to hydrogen selenide. This procedure is too s low to be considered except as an adjunct to zone melting. In the course of air-melting, many of the more easily oxidized impurities form a dross and may thus be readily removed. Substantial refinement with respect to iron, tin, chromium, aluminum, sodium, silicon, magnesium, calcium and manganese can be achieved in this way. Although tellurium can be electrodeposited from either acid or alkaline solutions of the dioxide, various factors militate against successful electro-refining, amongst which may be mentioned the brittleness of cast tellurium anodes and the tendency for the metal to be deposited in dendritic form, even at low current densities.

Feb 1, 1966

By Sina Z. Yekta, Zhangwei Ning, Pierre Frappin

This paper describes a DC (direct current) electrical resistivity method, which uses the contrasts in resistivity measurements to estimate the diameter of jet grouted columns as soon as they have been completed, with varying depth and water table, and without excavation. The measurement procedure is illustrated by several examples of application sites, including the Grand Paris tunneling works during the last 3 years where the method was systematically recommended in quality control for jet grouting works.

Sep 8, 2021

By R. A. Beall, S. L. Ausmus

The development of a completely water - free expendable graphite mold material , useful for reactive metal castings , has been detailed . Mixing and curing variables have been evaluated both by physical testing of the material itself and by castings of titanium , zirconium , and hafnium . The blend of powdered graphite , cornstarch , dextrin , cereal binder , linseed oil , and Carbowax -4000 is a successful mix when mulled in a carbon dioxide atmosphere , and properly cured and fired . The primary advantage of this material is its adaptability to standard foundry techniques ; i . e . , core blowing and hand ramming . Temperatures in the curing and firing cycles do not exceed 960 ° C , and no vacuum firing is required .

Jan 1, 1964

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

By Jan E. Nesset, Colin Hardie, Peter Radziszewski, Donald P. Leroux

"The successful introduction of new high intensity stirred milling technologies (e.g. IsaMill, SMDetritor) to the mining industry in recent years prompted Noranda-Falconbridge to initiate a study comparing these technologies to the conventional technologies of ball milling and existing vertical stirred mills (e.g. VertiMill). The study was unique in that it utilized the same material (Brunswick Mine zinc cleaner regrind mill feed), the same sizing instrument (a Malvern laser difractometer) and sampling protocol, and media size and type (for the high intensity stirred mills). The paper compares the net energy efficiency (kWh/t) of the various technologies, their power intensity (kW/m3) and product size distribution spread (P80/P20). A key finding is that media size is critical to achieving optimal performance. As part of the performance comparison, an analysis of the four methods of power measurement was made (Prony brake, shaft torque, grinding chamber reaction torque, “no-load” correction) and followed-up with an experimental test procedure using three of these methods. The findings include divergent results for power measurements and some explanations based on the observations are proposed. The direct shaft torque and Prony brake calibration methods are shown to be the methods most suitable for stirred mills.INTRODUCTIONThe motivation for the investigation reported here was the lack of a suitable comparison within the available literature of relative grinding efficiency for the emerging crop of new industrial fine grinding technologies. Such comparisons are potentially fraught with inconsistency, from ore samples and grinding media used, to testing methodology, to size measurement techniques, to the power measurements themselves. The collaboration of the industrial suppliers (at the time MIM Technologies and Svedala, now Xstrada Technologies and Metso Minerals) and McGill University (P. Radsiszewski) were sought in order to ensure as valid a comparison as possible. The work was performed between October 2000 and November 2002, led by the mineral processing group at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. The paper is presented in two sections; Part A considers the different power measurement methods and a comparison of the results for the SMDetritor (SMD) technology, while Part B reviews the grinding performance of the 5 technologies investigated using the selected performance criteria."

Jan 1, 2006