Search Documents

By Z. Zhang, R. G. Reddy

The viscosities of industrial lead slags with various compositions were measured as a function of temperature. It was found that viscosities of lead slags decreased with increasing temperature, and the plots of ln(11) vs. 104tr followed a linear relation over the reported ranges of temperature. Using the data of this study and available other related data from the literature, a viscosity expression was developed as a function of composition and temperature. The calculated results using this viscosity expression are in good agreement with the measured data. The composition dependency of viscosity of lead slags is discussed.

Jan 1, 2000

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

By M Scoble, A Ostry, J Shandro

Mining companies are not ill-informed on the topic of community health. There have been a number of research studies that have illuminated community health issues associated with mining, especially in the western Canadian province of British Columbia. However, what is missing amongst the literature is the perspective of mine managers and mining executives on this topic. This is important as mine managers and executives face a number of issues related to community health and are under pressure to consider the topic in more detail. This paper presents results from an exploratory qualitative investigation based on grounded theory research techniques into current community health considerations from the perspectives of mine executives and mine managers working in Western Canada. Interviews were conducted between February and May 2012 with 11 mining versus ten mining executives and managers who represented operating mines or mining umbrella organisations in Western Canada. Participants report on general community health issues that are perceived to be important, the perceived role that the mining sector should play?in contributing to community health and how this differs in Western Canada as compared to locations abroad, and?risks companyÆs face in making community health contributions. This paper concludes by drawing attention to pressing health needs that are present in Northern, rural and Aboriginal populations in Western Canada and provides a platform for future research initiatives focused on improving the health and well-being of communities associated with the mining industry. CITATION:Shandro, J, Scoble, M and Ostry, A, 2012. Community health considerations from mining executives and managers in western Canada, in Proceedings International Mine Management 2012, pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By F. -Z. Ji, A. G. Irons, M. Barati, K. Coley

In order to optimize carbon injection into oxidizing slags, in terms of carbon and iron yield, we must have a detailed understanding of the kinetics of the reactions involved. The current study measures the rate of carbon oxidation during injection at steelmaking temperature by means of injections of coal into EAF slags. The compositions of analysed outgoing gas were used to calculate gas flow rate and hence the gasification rate of carbon. A fundamental equation to predict residual carbon in slags was developed. The predictions using this model at moderate injection rates are in good agreement with experimental data. The reaction rate of EAF slag with carbon is under mixed control by the slag gas and the gas carbon reactions. The relative importance of each step depends mainly on the v-ratio of slags. A relative reactivity parameter ? has been defined and it is found to be important to carbon-slag reaction kinetics and slag foaming. Key words: carbon-slag reaction, kinetics, slag foaming.

Jan 1, 2004

Safe, efficient production is a common objective for all large open pit mines. Despite comprehensive policies, procedures and regulations aimed at protecting workers, several people die each year in mining equipment-related collisions. The limited sightlines of heavy equipment operators coupled with difficult operating conditions are major contributing factors to the majority of mining equipment collisions. Off road haul trucks are the most common type of machinery involved in surface accidents. These vehicles represent the primary target for improving safety performance by mine operators. Although several commercial products have been introduced to address these issues, none have achieved significant market acceptance. The current collision avoidance solutions lack integration with onboard fleet management and equipment health systems. To achieve acceptance in industry, any collision avoidance system must offer high reliability, minimal false alarms, and value for money. With these criteria in mind, this paper will examine the pros and cons of the various technological approaches to collision avoidance in an open pit mining environment. The unique global positioning systems (GPS) and camera-based proximity detection solution on offer from Modular Mining Systems will be described. This solution uses intelligent filters to minimise false alarms. Tight integration with fleet management provides context information to enhance warnings and enable back-office near-miss analysis. Available today, this combination creates a practical solution to improve the situational awareness of heavy equipment operators, at a compelling price point. Future directions for maximising heavy equipment operator situational awareness will also be examined.

May 1, 2010

By Rajiv Kalra, Ji Jiangang

"This paper reviews the following aspects of the world’s largest manufactured Grinding Mill’s in terms of diameter and power, along with the world’s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia.1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG – 28MW AG mills including FEA and major components3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG – 2 x 7.8 MW Ball Mills4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM’s and clients in July 2009.5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site.6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies.7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives"

Jan 1, 2012

By S. W. Parr, T. E. Layng

There is presented below the results of experiments made on six samples of Utah coals furnished through the U. S. Bureau of Mines , under an agreement dated June 16th , 1920. The details of all values for all runs are tabulated and presented herewith . Clear The samples, consisting of approximately 150 pounds each, were received at the University of Illinois , on June 15 , 1920 , and are listed as follows : Creek , Wattis , Castle Gate , King , Standard , and Aberdeen . The proximate and ultimate, analyses of the various ccals from that region , representing all the types included in these samples , have already been made by the Bureau of Mines , and are available . * Similar determinations were also made on the particular samples forwarded for purposes of these experiments . The results obtained on the coal as received did . not very in any material feature from the values reported by the Bureau, they are shown in Table 1. It is of importance to note only that the oxygen content is uniformly high , namely approximately 9.5 to 11.5 per cent of the as- received coal , while the oxygen - hydrogen ratio is also high, being on the average approximately 2 ( oxygen) to 1 ( hydrogen) .

Sep 1, 1921

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

The usual metallurgical, engineering and administrative activities associated with the handling and smelting of ores, and the subsequent handling and treatment of the products of smelting, present also problems of hygiene that engage the earnest attention of executives in all well-managed concerns.Again, associated with the employment of any considerable number of men, there is always present the problem of accident prevention.INDUSTRIAL HYGIENE.In the earliest records of lead min.ing and smelting there are references to the injurious effects of lead oh the health of the employees, and, with the advancement of medical science, lead poisoning has been the subject of many works by various authorities in many countries.Moreover, in practically every civilised country, there are laws governing the conduct of the lead industry, and in most cases these laws stipulate that employees shall receive compensation for disability caused by lead poisoning.This provision gives the problem an economic aspect. Apart from the legal and the economic aspects, however, there is the humanitarian aspect, which implies that the...

Jan 1, 1937

By J. Aiello

"Introduction Byron Creek Collieries Limited Corbin mine is located in southeastern British Columbia approximately 180 air kilometres southwest of Calgary (Fig. I), twenty four kilometres south of Highway No. 3 via a newly constructed provincial road (Fig. 2). The development of the area began July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J. Roberts first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co., after acquiring 6,000 hectares of land in the area, began to develop a mine. Mr. Roberts was responsible for the construction of the 22-kilometre rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production. The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3) and production from 1908 to 1930 inclusive totalled 2,120,800 tonnes. This production was allocated to the mines as follows:"

Jan 1, 1985

By Richard H. Olson

The following discussion will deal with the domestic talc industry only, inasmuch as the writer has had no experience in this field outside of the U. S. This is strictly a geological-mining approach; no attempt is made to assess in depth the effects which milling technology and marketing capability might have in determining the potential of any given talc deposit.

Jan 1, 1970

By P. T. Brooks

A process for extracting 69 percent of the vanadium from weathered Nevada dolomitic shale containing about 1 percent V205 was developed on a laboratory scale by the Bureau of Mines. The process essentially is comprised of salt roasting, leaching with dilute sulfuric acid, solvent extraction, and precipitation of vanadium as ammonium metavanadate. Carbonaceous unweathered shale was less amenable to treatment. A preliminary cost estimate for mining and processing 1,500 tons per day of weathered shale indicated a production cost of about 1 dollar per lb of V205. Considering recent sales at nearly $1. 75 per lb of contained V205, larger scale testing to obtain more definitive process design and evaluation data may be warranted.

Jan 1, 1974

By G. K. Derby

Paper presents project results investigating current techniques for dragline wire rope removal and the development of less hazardous means of performing the task. The cannon is the most prevalent method used in American surface mines. A cannon test program was conducted that used 40-and 50-grain primer cord to establish force produced using a 56-pound projectile. Socketlwedges were separated to establish separation force data. Two alternative removal methods, pendulum ram and portable hydraulic pusher, were developed and tested. Both provide sufficient force to effect separations under normal conditions on draglines with up to 78- cubic yard buckets.

Jan 1, 1984

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

By W. P. Haynes, A. J. Youngblood, J. J. Demeter

Synthesis of high - Btu gas , using the Fischer - Tropsch reaction was investigated in a tube - wall reactor of 2 - inch steel . The catalyst was carbonexpanded iron ( CEI ) , formed on the walls of a steel reactor by exposing the reactor to 1H₂ + 100 synthesis gas under certain conditions . Advantages to be gained from successful development of the CEI - coated tube- wall reactor are elimination of catalyst plant and catalyst handling and charging operations , high- temperature operation , and a relatively low- cost , reactor -heat recovery system . In one test ( TW- 8 ) in which the reactor was filled with CEI , the reactor was operated for 1,910 hours before the test was stopped because of excessive pressure drop caused by carbon deposition . The pressure drop was satisfactory for 1,000 hours of operation at an hourly space velocity of 300 , but it increased rapidly at space velocities of 600 and 1,000 . When operated at a space velocity of 300 , with a ratio of 1 to 1 recycle at 534 ° C , a conversion of 72 percent of the 3H + 100 synthesis gas was achieved . The product gas had a heating value of about 610 Btu per cubic foot and could be suitably upgraded to 900 - Btu gas by subsequent use of a nickel catalyst . CEI did not operate effectively as a film catalyst under conditions of generation tried in this study . Generally , operation of the 2 - inch reactor with CEI catalyst was unsatisfactory because of poor reproducibility of the activation step and poor temperature control resulting in high- operating temperatures and eventual plugging of the reactor . Tests using CEI in fixed , packed beds suggest that the most likely application for CEI in producing high - Btu gas would be a moving - bed reactor , where sufficient bed movement and heat removal are provided to prevent plugging .

Jan 1, 1964

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By R. S. Douglas

Introduction During the past few years, a number of changes in the mine operations at Copper Mountain have taken place. The modernization and mechanization were necessitated and given impetus by wartime and other conditions, which were: (1) The urgent need for copper for wartime purposes. (2) The scarcity of skilled labour for underground work. (3) The increase in labour and supplies cost. (4) The necessity of finding ways and means of increasing the output per man-shift, because of the scarcity of skilled labour and the rising cost of labour. (5) The desire to increase safety measures, reduce the silicosis hazard, and aid mine ventilation. (6) The desire to improve the general working conditions in the mine for all workmen. (7) The desire to reduce the amount of dilution in the ore stream by a more selective yet highly productive method of mining. To this end, mining with diamond drills, and transferring broken ore with slusher hoists, appeared to be the answer to the problem. After considerable discussion and estimation of costs for comparison with those of the operation as carried on at that time, the proposed methods were tried out and, in practice, gave very gratifying results. Reference at this point is made to the paper written by C. H. Brehaut, W. N. Taylor, H. A. Shannon, and R. S. Douglas, which was published in the September, 1945, issue of Mining Technology, by the American Institute of Mining and Metallurgical Engineers, Inc., and subsequently in commercial mining journals. Since that time some improvements have been made in undercutting an orebody - the first through experiment and practice, the second through making use of the earth's barodynamic or gravitational forces. It is the purpose of this paper to describe and discuss these later developments.

Jan 1, 1947

By J. Chirasha

Keywords: Pyrometallurgy, ferrochrome, smelting, investment, Zimbabwe Four smelting plants currently make up the ferrochrome smelting capacity in Zimbabwe. Zimbabwe Alloys and Zimasco represent more then ninety per cent of Zimbabwe?s ferrochrome smelting capacity, while Maranatha and Oliken contribute the difference. Very limited investment in the sector (even for the expansion of existing smelters) has been experienced over many years, despite the fact that about 95% of the world?s chrome ore resources are in the Bushveld Igneous Complex of South Africa and the Great Dyke of Zimbabwe. The Bushveld has a greater quantity but a lower grade than the Great Dyke. A ten per cent increase in Zimbabwean ferrochromium production has been recorded in the past ten years, showing an almost stagnant capacity investment.

Jan 1, 2011