Search Documents

By David Belknap, Clay Haynes, David Egger

Rehabilitation challenges were met nearly two months ahead of contract schedule for the Design-Build, Fast Track Scituate Aqueduct & Tunnel project in Cranston, Rhode Island. The aqueduct and tunnel were built in the 1920s and consisted of three sections—a 2.3 m diameter reinforced concrete section that extends approximately305 m before it transitions to a horseshoe-shaped 2.3 m wide by 2.1 m high cast-in-place concrete tunnel that continues for approximately 5.3 km until it transitions back to a 2.3 m circular section that extends approximately 1.9 km to the end of this project. Major repairs were required to assure sustained operation of this water supply tunnel.

Jan 1, 2005

By Arif Emre Dursun, Ali Aras, Hakan Özşen

Specific energy (SE) is defined as the amount of work required to cut a unit volume of rock and is used to estimate the performance of excavation machines. Generally, the SE value is produced from full-scale or small-scale rock cutting tests. However, these tests require expensive equipment and experienced personnel, and the testing procedure is time consuming and impractical. Therefore, for estimation of SE, this study aimed to find a solution to estimate SE using rock mechanics test results and Bond work index values (BWi), which can be produced in a more practical, less time-consuming manner and with inexpensive test equipment. Small-scale rock cutting, rock mechanics and Bond work index tests were carried out on seven rock samples, which can be grouped into two different type of rocks: marble and travertine. In addition, the instantaneous cutting rates (ICR) of a selected roadheader were calculated using SE values. Rock mechanics tests performed in this study were uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), ultrasonic velocity (Vp), Schmidt rebound hardness (RL), corrected point load index (Is(50)) and density (ρ). The simple regression method was used to estimate SE from rock properties and BWi. As a result of this simple regression, a significant and highest correlation was found between SE vs. UCS and Is(50). A good correlation was found between SE vs. BTS, RL and BWi values. A moderate correlation was found between SE vs. Vp and ρ.

Jul 28, 2021

By R J. Norris, D J. MacKenzie

Gold-bearing veins have formed at a wide range of depths throughout the uplift history of the Otago Schist. The earliest gold mineralisation occurred during the later stages of Mesozoic metamorphism. This mineralisation was characterised by diffuse wall rock alteration with greenschist facies metamorphic or retrograde metamorphic mineral assemblages, and gold occurs in this altered rock. Quartz veins formed in .steeply dipping extensional fractures associated with this mineralisation type strike north to northeast. The Macraes mine exploits this deposit type. The present northwest strike of the mineralised zone at Macraes is a result of post-mineralisation deformation of the schistosity-parallel mineralised shear zone which hosts northeast striking extensional veins. This combination of schistosity-parallel shear zone and steeply dipping northeast striking veins may exist elsewhere in Otago, and this deposit type is most prospective. Steeply dipping quartz veins formed during post-metamorphic un-roofing of the Otago Schist strike northwest to west and occur as clusters of near-parallel structures in east and central Otago. These veins consist mainly of massive quartz, although some prismatic quartz occurs also. Breccia fragments in veins are common and these are generally silicified, with some gold. Wall rock alteration is negligible, and vein margins are sharp. A set of middle Tertiary veins occurs in northwest Otago. Most of these also strike northwest and dip steeply, but some strike northeast. These veins contain abundant ankeritic carbonate as well as quartz. The carbonate pervades adjacent wall rock as veinlets, but gold mineralisation is confined to veins. Quartz is commonly prismatic and vuggy, and contains gold, which is commonly coarse grained especially in silicified breccia zones. Associated veins contain stibnite. This vein type formed close to the paleosurface (>2 km). Mineralised veins in Marlborough currently strike northwest, but these have been rotated from northeast strike during Alpine Fault displacement of Marlborough from Otago. Some of these veins were formed under late metamorphic conditions and are similar to the north to northeast striking veins in Otago. As in Otago, this type should be considered to be most prospective if they have associated schistosity-parallel shears.

Jan 1, 2000

By E. Saari, B. Musuku, K. Jansson

The quality of the concentrator plant process water is crucial for high performing mineral flotation circuits. Significant metal recovery and concentrate grade losses have been noticed particularly in more closed water loops. The recovery and quality losses have started to emerge mainly with decreased freshwater usage and because of changes in tailings management towards tailings thickening, paste, or dry stacking. These changes result in shorter, closed water loops with a rapid build-up of harmful components with negative impact on the beneficiation process. Consequently, water quality has a direct link to decreased product value and sales returns. Complete cleaning or water blending might not be the right way to achieve high recovery and high-quality products. Instead, the key is to understand what kind of water qualities are needed for the flotation of specific minerals. In this study harmful substances in various plant water streams were removed and/or modified by pilot-scale dissolved air flotation. Batch-scale mineral flotation tests with the untreated and treated water were then performed by using fresh ore samples and the plant’s own laboratory flotation procedure. The results indicate that because of dissolved air flotation, the mineral flotation recoveries were enhanced by 1‒3.3%. Keywords: Mineral recovery, metal recovery, mineral quality, process water, concentrator, beneficiation, mineral processing, flotation, process water treatment

Jan 1, 2020

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By Marsh A. Cooper

THE THEME of my remarks provides a great deal of latitude. I shall therefore take advantage of the scope it offers to look at our industry across a broad spectrum. My observations reflect a Canadian mining man's varied career as a geologist, mine operator, geological consult ant and company executive in Canada and overseas ... under differing cultures, business environments and political jurisdictions. I was fortunate to come into this industry in the mid-1930's when it was characterized by great enthusiasm, drive and resourcefulness. It was the beginning of a burgeoning era of some 30 years' duration in which the individualist, the entrepreneur and the builder found ample room for expression. As I contemplate the environment in which we now have to operate and try to perceive what lies ahead, I find myself deeply disturbed. Something serious has happened to this industry along the way. It appears that our very success has been the source of our undoing. I believe it is useful to summarize our industry's basic strength at home as a take-off point f or assessing its position in world terms. I hope that I can focus on some of the things that, in my view, must be done for this industry and by this industry to restore Canada's historic role in the world mining community. The Canadian mineral industry provides 140,000 jobs. It pays the second -highest average weekly wages and salaries among the country's major industries. The output per employee in the mining industry is estimated at about three times that for the economy as a whole.

Jan 1, 1977

By James W. Myers

"Packaged fuel" is the trade name applied by the industry to a product consisting of coal screenings and a binder compressed into 3 -or 4-inch cubes and wrapped (six or eight in a package) in sturdy paper and sealed with gummed tape. Parry describes the product in greater detail and distinguishes clearly between packaged fuel and briquettes. The industry developed from the desire of retail coal dealers to improve utilization of the relatively large quantities of slack sizes that result from the degradation, during shipping and handling in the yard, of friable coal, particularly Pocahontas coal. During the war an attempt was made to apply this technique to anthracite fines, and a recent publication of the U. S. Bureau of Mines reported the results of physical and combustion tests on packaged fuels containing anthracite fines. References made in this report to the previous investigation on packaged fuels containing anthracite represent data or conclusions presented in Report of Investigations 3882. This investigation was conducted as a continuation of the previously reported studies and consisted of physical and combustion tests of packaged fuels made from high-volatile bituminous coal, as well as the low-volatile bituminous coal ordinarily used in the industry, to determine their relative suitability for domestic firing. Particular attention was given to the smoke-producing properties of the packaged fuels because of the increasing importance of the prevention or reduction of smoke from hand-fired domestic heating plants resulting from the widespread enactment of smoke-prevention ordinances.

Jan 1, 1951

By Robert Griesbach

One of the important decisions in the development of new mining concentrator projects is the electric power supply for the project. Key decision factors often include the production of power on site versus purchase of power from the grid, ownership of the power supply infrastructure and the choice of generation technology. In this sense, the paper introduce a methodology that will allow the evaluation of the various alternatives to supply electric power to remote mining and mineral processing sites in a consistent and equitable manner taking into account economic and technical considerations and providing the same degree of availability and reliability. The most employed evaluation method consists of carrying out trade-off studies between the various alternatives but care should be exercised so that the alternatives analyzed offer comparable operational results.

Sep 14, 2009

By Shadia J. Ikhmayies

SnO2:F/CdS:In bilayers were produced by the spray pyrolysis technique on glass substrates. The structures were characterized by recording and investigating their transmittance curves, I-V plots, X-ray difractograms (XRD) and by observing their scanning electron microscope (SEM) images. From the I-V plots it was found that the SnO2:F forms an ohmic or quasi-ohmic contact with CdS:In. XRD patterns show the polycrystalline nature of the films and show that there is a small shift in the position of the (200) line of SnO2:F without the appearance of new peaks. The morphology of the structures are compared with those of SnO2:F alone and CdS:In alone on glass substrates.

Jan 1, 2009

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

A quantitative chemical model of the rocks of the Broken Hill lode environment is presented to illustrate a stratiform orebody in a meaningful form to scientists interested in environmental control on the chemicalcomposition of sediments.Even though this study was restricted by the narrow range of rock analyses available it is obvious that significant chemical differences exist between the various rock units and also that some association of metallic sulphides with Ca, Mn, Fe, and P is indicated.Correlation of this evidence with that from other mining fields may point out more definite chemical relationships and elucidate the puzzle of the mode of formation of many stratiform orebodies.

Jan 1, 1968

At its Copper Cliff Smelter, Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces, The furnace matte is converted to low iron matte for further processing, and the molten converter slag is recycled to the flash furnaces. The flash furnace slag is discarded. Natural gas or coke supplies a minor proportion of the process heat requirements, thus limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as S02 in the flash furnace. Preliminary experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. This paper presents the experimental results and discusses key aspects of the possible operation of the Inco flash furnace with a coke barrier separating the freeboard from the molten bath.

Jan 1, 2003

This evening I would like to speak about men for the mineral industry.It is trite to say that the mining industry is expanding rapidly and that technically trained men are in short supply. How short is difficult to assess and impossible to quantify.The industry has been traditionally managed by technically trained men experienced in the ways of their fellow men. Let us start with the assumption that men with this training and experience are essential to management of mining and metallurgical enterprises.I suggest that we do this as it avoids argument with those who are beginning to suggest that such men are not so important as they used to be; who are suggesting that the latest sophisticated business management schools can produce managers who can straight out of school join the upper echelons of an organization and successfully manage it by the use of modern systems and techniques without the need to rub shoulders with men of all callings and get their hands dirty in the process.This kind of thinking brings to mind the modern cargo ship which is equipped with all the latest gadgets of science. It can find its way from Sydney to Auckland with no one in the engine room and the man on the bridge spending most of his time writing to his wife or reading the latest novel.How often do we read of this ship being tied up in Sydney because the crew sympathizes with the cook who has been slighted by some uncomplimentary remark about his toheroa soup? Here is a pieceof sophisticated machinery stopped through no technical fault, but held up by the whim of man. The understanding of man by man can spell the success or failure of any endeavour. A single man can leadan organization to the pinnacles of success, or doom it to utter failure in spite of modern systems and techniques.So let us start from the point that people matter.Through the years our Institute has been fortunate in having many members who have felt strongly...

Jan 1, 1970

By Fred J. Miller

FRED J. MILLER was born in Ohio, in 1857. He had a common and high school education, supplemented by personal study and special instruction. After serving a 4-year apprenticeship and working in various capacities in machine shops, he became a contributor to mechanical journals and finally a member of the editorial staff of The American Machinist, where he remained for twenty years, the last ten years as editor-in-chief of the magazine, and vice-president of the publishing company. On retiring from journalism, he was for nine years general manager of a group of typewriter factories, and was then commissioned Major of Ordnance in the U. S. Army, being stationed during most of his service at Rock Island Arsenal, where he organized the Civilian Service Division of the Arsenal. He is now a member of the Technical Advisory Committee of the War Claims Board at Washington. Major Miller became a member of the American Society of Mechanical Engineers in 1890, and has always taken an active interest in its affairs, having served on a number of important committees, and as a member of Council from 1904 to 1907, inclusive. He was elected President in December, 1919.

Jan 1, 1920

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989

In preparing a paper such as this it was thought that the Newstan Colliery Company Ltd., being comparatively new, would need some introduction to mining people in general.The Newstan Company was formed by the Joint Coal Board in December, 1948 during a period of acute coal shortages. The Company took over the holdings of what were known as the Olstan and Northumberland Collieries, situated at Fassifern, alongside Lake Macquarie and adjacent to the Great Northern Railway, within easy rail access of Sydney and Newcastle, as shown on the locality plan (Fig. 1).The Company was developed in order to produce steaming coal for the power house trade and has continued its activities in the steaming coal trade since its inception. The Olstan and Northumberland collieries were together producing some 300 tons per day when the Company was formed, and it was from this foundation that the colliery was built. The planned development of the Company has been along the lines of producing coal by modern, highly mechanised methods, together with the preparation of theproduct for the consumer, to the highest degree possible consistent with up to date methods.In the comparatively short time of 5t years the mine has developed from a small hand-won coal unit to a high capacity modern mine, one of Australia's largest producers, with an output capacity as high as 3,000 tons per shift.

Jan 1, 1954

By L. J. Hoover

The objective of this study was to assess the health and environmental impacts of fluidized-bed combustion (FBC) of coal, specifically as applied to baseload generation of electrical energy by utilities. The study* was a short-term effort that based its analyses on information derived from the experience of the group or quickly obtained from the literature. The approach was to compare Atmospheric Fluidized-Bed Combustion (AFBC) and Pressurized Fluidized-Bed Combustion (PFBC) with two current technologies: low-sulfur coal combustion (LSC) and flue gas desulfurization (FGD) used with high-sulfur coals. A wet-limestone process was selected as the FGD technology. The impacts compared involved not only health and environment but also sociology, resource use, and dollar cost. Conditions for comparison were centered around a nominal date of 1988, when initial operation of commercial AFBC plants may occur. The PFBC has a later introductory date, a nominal 1995 (its impacts relative to other competitive technologies now in the R&D stages were not compared.)

Jan 1, 1978

By G. K. Herzog

THE problems relating to the construction and use o{ mining equipment are basically the same as those pertaining to equipment in other industries. It is true that much mining equipment is subjected to an unusually severe combination of shock, high stresses, abrasive wear, and corrosive ? conditions, but in other industries, also, equipment must operate under similar adverse conditions, so that their experiences may readily be applied to the problems of the mining industry. Steel and iron are for obvious reasons the most suitable materials for the construction of the greater part of the equipment used in the mining industry. For a large percentage of uses, the ordinary plain carbon-steels and ordinary or unalloyed cast-iron are, and probably will continue to be for a long rime, entirely satisfactory materials. There are, however, many. conditions which cannot be satisfactorily taken care of by these materials, and alloy steels and irons must be used where the greatest possible economy is desired. In general, alloy steels and irons are used where it is necessary or economically desirable to use materials possessing properties superior to plain carbon-steel or ordinary cast-irons, such as: (a) better strength (b) better wear resistance (c) better corrosion resistance (d) better resistance to high temperatures (e) better resistance to low temperatures or combinations of two or more of these advantages. There are also conditions where materials having other special properties are required, such as, for example, certain magnetic or electrical properties for electrical machinery; but in the great majority of cases, one or more of the five advantages listed are the most desired.

Jan 1, 1938

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014