Search Documents

By Fernando Castro

Electric furnace steelmaking dust is a polluting residue that needs to be treated in order to recover metals contained and to produce an environmentally acceptable residue. Some hydrometallurgical approaches for its treatment have been evaluated, namely: caustic soda leaching followed by electrolytic recovery of zinc, ammonia leaching followed by zinc compounds precipitation and acetic acid leaching followed by lead, zinc hydroxide and gypsum precipitation.

Jan 1, 1992

By Yury Kapelyushin

Formation of cementite in the reduction of hematite by CO–CO2 gas was studied in situ using high temperature XRD (HT XRD) analysis. Reduction of hematite was examined in the temperature range 873–1173 K by CO–CO2 gas mixture with high carbon activity. When carbon activity in the system was 1.5, cementite was formed only at 1023 K; it was not observed in experiments at 973, 1073 and 1123 K. Formation of cementite was observed at 923–1073 K when carbon activity increased to 3–5; and at 873 K when carbon activity was 10. Formation of cementite at 973–1073 K proceeded through metallic iron; however, in the reduction of hematite at 873 and 923 K, iron was not observed; cementite apparently was formed directly from wüstite. XRD spectra were used to estimate concentration of carbon in austenite in the process of cementite fromation.

By Alexander Sutulov

1. INTRODUCTION According to the classical economic approach of the open market economy, copper supply should be regulated by market forces which are (a) demand and (b) prices. In fact, demand is of primordial importance because prices are a reflection of supply-demand balance: they go up in times of shortages of supply and down when over-supply situation exists. In the past few years, this basic mechanism of market economy has been under pressure from a number of non-market forces, such as social and monetary problems of sane important copper producing countries; structural changes in copper mining companies through mergers with oil companies; and other factors which greatly contributed to distortion of the basic supply-¬demand equation. As a result, we have faced in the last three years a situation of oversupply rarely seen in the past, with a catastrophic fall in copper prices, huge losses at mines and unprecedented indebtedness of copper producers. This has deep repercussions in the copper business and its future supply outlook. This is particularly so when taking into consideration that high indebtedness and high interest rates conspire against the very survival of some traditional producers. As we write this comment (July of 1985), close to one half of U.S. copper production capacity is closed down, sane of it for good, while the same precarious situation exists in Canada, Australia, Zambia, and some other primary producers who cannot face present low prices with equally low costs. The question is then what this situation means for the medium-¬term future, until the end of this decade, Particularly when taking into consideration the fact that some of the factors influencing it are of a long-term character. 2. SUPPLY-DEMAND SITUATION IN THE LAST FIVE YEARS Since the last boon year, in 1979, when world copper consumption reached a record of 9.8 million metric tons of refined copper, demand dropped to only 9.0 million tons in 1982, when the crisis bottomed out, and then steadily recovered to the level of 9.7 million tons in 1984. Meanwhile, copper production, which in 1979 was only 9.4 million tons, in spite of the fall in demand, grew to 9.7 million tons in 1981 and 1983 and only temporarily was cut to 9.4 million tons in 1982 and to 9.5 million tons in 1984. As a result of this imbalance, hugh copper stocks were accumulated with supply systematically out¬growing demand by over 2 million tons at one time. With the Western World refined copper demand running at an average of 115,000 tons per week, this oversupply was equivalent to between 15 and 18 weeks production, i.e. twice as large as normal. This was immediately reflected in very low copper prices. Another contributing factor to relatively low copper prices was the lack of speculator interest for this commodity. Between 1981 and 1984 the world experienced a very intensive period of wealth distribution, high interest rates and intensive restructuring off world economy and its industrial sector. Therefore, much of the available money was attracted to more lucrative and attractive investments rather than to the lack-luster performance of copper, and for that matter, of the metal sector in general. The much announced and discussed recovery of the U.S. economy since 1983, and particularly in 1984, with an overall growth of the GNP by 6.8% in 1984, happened to be more oriented to the service sector than the industrial sector and therefore this recovery was not adequately reflected in copper consumption nor to metals in general. This put serious doubts about the future demand for copper. Consequently copper prices failed to improve in spite of an apparent fall in stocks and a healthy increase in the demand for copper since 1982. At the time of this writing (July, 1985), although same analysts claim that the available stocks are running at about 8 weeks of supply, which are considered to be below normal, copper prices are still very low at between 65 and 67 cents per pound of copper. Part of the answer may be the normal seasonal slow-down period in the Northern Hemisphere due to summer vacations and

Jan 1, 1986

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By P. Schmäh

Nowadays, small diameter tunnels are increasingly considered in pipeline projects as an alternative for sensitive crossings or when soil conditions limit the use of conventional pipeline installation methods like HDD. Safety concerns play a key role, especially for inner-city installations. Pipe jacked microtunnels and small segment lining tunnels can serve as casing tunnels if access is required during construction for the change of cutting tools in challenging ground conditions or for maintenance of the pipeline in operation. Small diameter tunneling solutions offer a high degree of flexibility for alignment design in terms of geology, length and radius.

Jun 13, 2021

By C. Sarkar

Increased competition in today’s global economy has put mineral industry under excessive pressure to effectively manage production assets to generate business wealth. Capital intensive industry (CII) organizations are seeking ways to manage skill resources, internal processes, and organizational networks with a view to reduce the cost of ownership of assets and increase efficiency of operations and service. The emerging concept of Enterprise Asset Management(EAM) is a collection of business processes that allow CII with right focus on return on investment on assets, to make right decisions on planning, acquisition, maintenance, operation, rehabilitation, and disposal of assets. Information technology (IT) can drive significant returns if the infrastructure covers seamlessly all business processes and all systems, like geographic information system, maintenance management, investment management, laboratory information management, and supervisory control and data acquisition system. The simple approach to IT in the past with disconnected silos of technology, information, and business processes cannot deliver the expected benefits under the modern business environment. Identification of business and application component is a prerequisite for the development of an asset management system that links effectively disciplined processes having characteristics of agility, speed, and integration. This paper discusses various issues and outlines the steps for developing an asset management roadmap in an organizsation. It also presents major business and application components of the system. Keywords: Enterprise asset management, Business architecture, Business component, Application component, Asset ownership, Asset operations, Information technology, Capital Intensive industry

Jan 1, 2003

"Chairman: Mr. K. F. LaneRapporteur: Mr C. T. ShawPapers:Design of crushing plant flow sheets by simulation by T. GurunThe impact of transportation networks upon the potential supply of base and precious metals from Sonora, Mexico by P. de V. Harris and D. E. EurestyProfitability sensitivity analysis of a mining venture by C. A. Beasley and E. P. PfleiderTechnological innovation and its potential effect on the opening of new gold mines in South Africa by N. C. JoughinMr Turgay Gurun, in presenting his paper, indicated that this simulator was no purely theoretical exercise, but that the model had been used in the design of crushing plants of capacities ranging from 3 000 tons per day to 66 000 tons per day, and that recently the design of a plant of capacity of 99 000 tons per day had been studied.The crushing plant simulator was an independent portion of a much more comprehensive simulator for the design of a. complete recovery plant. It would be possible to use each section of this simulator on its own, and simulators would be designed to cover flotation concentrates, cash flow analyses of the entire project, and so on.Each simulator would be backed by a comprehensive data bank. For example, the crushing plant simulator was backed by such a data bank which included the performance and cost data from five manufacturers for an average of 30 items of process and materials handling equipment each. This meant that data preparation involved generally less work than would be required for a manual calculation. On average, data preparation for one run took 30 minutes and three minutes of computer time on an IBM 360/40 completed the run. The model could be valuable as a design tool in that it allowed the designers an opportunity to make a thorough examination of many alternative designs. It was also of value to plant operators as it could be used to predict the consequences of operating decisions.This paper generated much interest and there were numerous questions and contributions, so many, in fact, that the discussion had to be cut short.It was pointed out by Mr K. F. Lane that crushing plants represented a very large capital investment. A plant designed for 40 000 tons per day at 98 per cent efficiency might well in practice be run at 50 000 tons per day at, say, 83 per cent efficiency. He asked how, therefore, their design could be investigated without building economic criteria into the model? The author conceded that this was a tender point. He would have liked to have given facilities for more variability of the metallurgical information. He pointed out, however, that while there was no overdesign for conservatism built into his system, some overdesign was inevitable as the performance characteristics given by the manufacturers were generally conservative. Also, in his system, if lower recovery was allowed for, the system would nut through more tonnage."

Jan 1, 2014

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on site facilities depending on the ore type and the grade. The processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and the complexity of the operation, there are unique challenges in optimizing life of mine production scheduling. This paper describes those challenges and the methodology developed to take advantage of different scheduling software systems that effectively compensate each other and result in reasonable guidance. The paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Feb 27, 2013

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Automation and robotics are the keys to new intelligent autonomous mining systems which can remove operators from the hazardous and stressful mining environment and provide the tools for greater productivity. This pa-per presents the components necessary for a mining Intelligent Task Control System (ITCS) in dynamic unstructured mining environments. The proposed concept is applied to develop the ITCS for an autonomous excavator. The design and implementation of a fuzzy logic controller for an excavator that uses force/torque sensor feedback to complete excavation tasks is presented. Initial experimental results are also given.

Jan 1, 1994

Published experimental data on thermodynamic behaviour of cobalt-containing slags have been reviewed and used in validating a recently developed thermodynamic model. The results from the exercise show that the model provides a reasonably good description of behaviour of cobalt in multi-component slag systems. The models for cobalt containing slags, matte and oxide solid solution phases were incorporated into CSIRO?s multi-phase equilibrium (MPE) package, which was used to calculate the equilibrium distribution of cobalt between matte and slag phases under various conditions. The results agreed well with the experimental data. Furthermore, the good agreement between the calculation and the plant data indicates that the operating conditions of industrial smelting and converting processes are close to equilibrium. Two diagrams showing the effects of slag chemistry and SO2and O2partial pressures on the distribution of cobalt between phases were generated for conditions similar to smelting and converting processes. These diagrams provide some useful guidelines for developing new strategies to improve cobalt recovery.

Jan 1, 2004

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By Bruce Vandenberg, R. Frank Chiappetta, John Foley

Recent advances in solid-state, field portable, fast framing compact video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 4.1 seconds of data can be captured directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the MotionMeter system and compare these with the analogous aspects of film-based cameras and other systems. Of all blast monitoring systems and techniques available today, high-speed motion picture photography and videography still remain as the most valuable, stand alone, diagnostic techniques for troubleshooting and evaluating full scale blasts in the mining and explosives industries. High-speed image data, coupled with information obtained from other instrumentation systems, such as continuous velocity of detonation recorders, laser surveying systems, refraction and ground vibration recording seismographs, etc., can eliminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both excellent and poorly designed blasts is increased, and optimum blast results, (which are application dependent), are achieved considerably faster when compared to the trial and error approach of relying on strictly the experience factor. Applications include developing site-specific blast designs, decay equations relating burden, burden velocity and explosive energy, determining ground response times, reducing coal damage, quantifying backbreak, evaluating the effectiveness of sternming, checking delay detonator firing times, evaluating air decks and for studying general dynamics. Motion analysis is performed with a 2D and 3D software package developed specifically for video analysis, but is also directly applicable to film analysis when using a digitizer. Dimensional controls, lens aberration, field set-ups and camera orientation are all automatically corrected for with matrix analysis.

Jan 1, 2000

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack. Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By Kenneth M. Haley

THE development of Reserve Mining Company's pelletizing practices began in 1949 in a pilot plant located at Ashland, Kentucky. Three years later the participating companies -Armco Steel Corporation, Cleveland Cliffs Iron Mining Company and Republic Steel Corporation concluded the work and the small plant was shut down. Oglebay Norton and Company was the operating manager and Armco Steel Corporation furnished labor and services. Arthur G. McKee and Company were the designers and constructors. The equipment flow sheet that was employed in that pilot operation is shown in Figure 1. This was Reserve's first step from the laboratory work per-formed by the Mines Experiment Station of the University of Minnesota in developing a commercial operation. The plant used New York state concentrate, purchased from Jones and Laughlin Steel Corporation's Benson Mine. This concentrate, minus 14 mesh, 64.3 per cent Fe, 5.7 per cent Si02, was processed at Ashland to 80 per cent minus 325 mesh in conventional ball mill, classifier, thickener, filtering

Jan 1, 1961

By S. Makni, F. Wang, A. Rosa, B. Klein, C. Saud, R. McIvor, A. Kumar, C. Gagnon, D. Gong

In response to the Natural Resources Canada “Crush It Challenge”, Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling, with high-pressure grinding. Two plant case studies, a small tonnage gold recovery operation, and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed set up to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of highpressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone, and final stage total circuit energy savings, exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Mar 2, 2022

By Clarke P. E

At the end of the recent war, reports became available from Europe of the use of tungsten-carbide inserts in percussion rockdrill bits. These bits were used with small size rockdrills, so that the only advantage gained from the use of the harder, abrasion resistant, tungsten-carbide appears to have been the greater life of the bit. Larger machines, such as used in Australia in conventional practice, had to be discarded to protect the relatively brittle tungstencarbide inserts and the vulnerable bonding with the bit body.As it had been found in machine shop practice that some grades of tungsten-carbide had been produced with considerably improved toughness, it was decided by Gold Mines of Australia Ltd. that drilling practice with tungstencarbide bits warranted detailed examination under Australian conditions, and that drilling tests should be undertaken at Morning Star (G.M.A.) Mines N.L., for which it acts as General Manager and Consultant.These investigations progressed through three stages:1. Preliminary Investigations and Tests.When the investigations were initiated no commercial bits were available in Australia, and manufacture was commenced with improvised equipment from virtual scratch. These early tests indicated that the use of 3 in. bore rockdrills in conjunction with tungsten-carbide insert bits was a 'possibility, and that it was unlikely that a small bore...

Jan 1, 1950

The Tennant Creek goldfield is situated in the Northern Territory, 360 miles north of Alice Springs, or a tot~l distance of 1,300 miles north of Adelaide, and 600 miles south of Darwin. The auriferous area extends 20 miles north and south by 50 miles east and west. The overland telegraph line and the AIice Springs-Darwin road pass through the centre of the field.HISTORY, PRODUCTIONThe country comprising the goldfield was traversed by J. MacDouall Stuart between 1859 and 1861 in the course of his last three exploring expeditions, which terminated respectively at Attack Creek, Newcastle Waters and at the mouth of the Adelaide River. The explorer named Tennant Creek and also Mount Samuel, on which mining operations are now in progress. The overland telegraph line was completed in 1872 and a relaying station established eight miles north of the site of the present township. There was no other settlement in the adjacent country prior to the opening up of the goldfield.Gold was discovered in 1926 on what is known as the Great Northern lease, three miles north of the township. The field was remote; the nearest plant at which gold ore could be treated was at Peterborough, in South Australia, 1,186 miles distant, and it was not until 1932 that the development of the field actively commenced.The production of the field from its inception to December 31, 1939, was 57,895 QZ. of gold, valued at £522,000, recovered from 61,793 long tons of ore, won from 98 mines. In 1940 seven of these mines had reached depths between 100 ft. and 230 ft., the workings of the majority being less than 60 ft. below surface.TOPOGRAPHY, WATERThe country is traversed by parallel and sub-parallel lines of hills trending east and west and rising to altitudes varying from 50 ft. to 100 ft. above the intervening valleys. The low ranges and isolated hills owe their survival to the resistance offered by their indurated, harder rocks to erosion which has removed the softer intervening formations. Their elevation and area depend to a considerable extent upon the presence of; and, the size of, the more or less exposed haematite formations, or are due to the influence of extensive siliceous dykes which traverse the locality.Watercourses head from the hills and either flood out on the flats within a short distance, or in a few cases follow longer courses to the northward. In the channels of the larger creeks billaoongs, which form important water storages for a considerable part of the year, -are to be found. Tennant...

Jan 1, 1942

By Simon St. John Tose

We have had a long history in supporting the development of training material to ensure “safe” blasting. This has been provided as both significant technical guidance to the industry and input into the development of the new industry surface rockbreakers or shotfirers qualification in South Africa (RSA). The learning material supplied to the industry is based on both a classroom knowledge component and an assessment on the practical application of the learning by the trainee blaster on the job under the supervision of the appointed blaster. This training includes all blasting applications which can often extend beyond the “normal” mining environment of open pits, underground and quarries into civil applications such as trenches, blasting close to private buildings, public roads, pipelines, power lines, swimming pools and the removal of concrete structures and building demolitions etc.

Jan 1, 2013