Search Documents

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By S. H. Ash

NINE-TENTHS of the total anthracite deposits of North America are in Pennsylvania. Corrosion of pumping equipment by acid mine waters has been experienced at tremendous cost by mining companies in the anthracite region of Pennsylvania, for many years in many ways. The design and specifications of the large centrifugal pumps as provided in the proposed mine-drainage system (7-35, 45, 46, 48, 54, 64, 70, 71)° make it imperative that a metal or alloy be recommended that has the highest corrosion resistance and, at the same time, acceptable properties suitable for general workability (welding and machining). This report presents data on the corrosive and erosive effects of acid mine waters in the anthracite region on metals and alloys for pumping equipment and drainage facilities necessary to remove or control this water.

Jan 1, 1955

By T Baumgartl, M Edraki, L Huang, D R. Mulligan

"Phytostabilisation with tolerant plant species has been advocated as a cost-effective solution for sustainable cover of tailings from metal mines and bauxite refinery. The development of sustainable plant ecosystems on such wastes requires not only tolerant plant species compatible with local climatic conditions, but also the formation of stable and functional root zones through systematic processes to develop functional soil matrix and horizons (eg A-B-C). However, the process requirements for reconstructing functional root zones in tailings are poorly understood. Based on a review of current literature and industry experience in tailings revegetation, the present paper conceptualises three key phases in the process of root zone development in amended tailings: hydro-geochemical stabilisation resulting from the interactions among tailings characteristics, amendment measures and local climatic conditions the rehabilitation of soil biological capacity the establishment of ecological (carbon and nutrient) linkages between the rehabilitated root zones and the above ground plant communities.Key research is required on: the relationship between hydro-geochemical stability and mineralogy and geochemistry of tailings, in response to rehabilitation treatments under local climatic conditions the relationship between soil biological capacity and hydro-geochemical stability in the root zone the transition of soil microbial communities specific to exogenous organic matters into those required for mineralising litters of in situ plant communities.CITATION:Huang, L, Baumgartl, T, Edraki, M and Mulligan, D R, 2012. Sustainable phytostabilisation of mine tailings - A critical analysis of system requirements and approaches, in Proceedings Life-of-Mine 2012, pp 105-116 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By Henry N. McCarl

[ ]

Jan 1, 1966

By E. P. Evert

Profitable marketing of most minerals is dependent upon the total delivered cost to the user. Transportation costs are often greater than the value of the mineral f.o.b. the mine or processing facility. In some cases, transportation costs are three to five times the mineral cost. For many years, transportation costs were controlled by a complex system involving the transportation companies and supervised by regulatory agencies. This paper will deal with the effects of deregulation on rail costs and outline the major changes in transportation economics.

Jan 1, 1985

By Paul Zick

The Port Authority of Allegheny County North Shore Connector (NSC) Project involves TBM excavation of twin 690 m (2,240 lf) precast segment lined light rail tunnels through soil and rock under the Allegheny River and a narrow, downtown city street. The $435 M project is funded 80% ($348 M) by the Federal Government, 17% ($72.5 M) by the State of Pennsylvania and 3% ($14.5 M) by Allegheny County. Along the tunnel alignment are a historic building on shallow foundations, modern buildings on deep foundations, and one building constructed directly over the alignment. The project includes construction of twin 369 m (1200 lf) cut and cover concrete box tunnels and an underground station shell. This paper provides an overview of general site conditions, current project status and construction challenges for the Twin Tunnels and North Shore Light Rail Station.

By R. J. O'Dea

"The United States hat large reserves of titaniferous iron ores that are a potential future source of both iron and titanium. Although it is not now economically feasible to recover iron and titanium metals from these ores, they may become important in times of stress and, in some instances, already have served as a source of pigment-quality titania.The iron- and titanium-bearing constituents of the ores considered in this report are not completely separable from each other by ore-dressing methods, and chemical (or smelting) procedures must be employed. It is im¬portant, therefore, that information be available concerting their reactivities. The most important titanium-bearing constituent is ilmenite (FeTiO3), the thermodynamic properties of which were discussed in a previous publication.3/ The results of thermodynamic studies showed that both hydrogen and carbon monoxide are relatively ineffective reducing agents for the iron in limonite. On the other hand, carbon theoretically is effective at tempera¬tures above 8510C., at which. point the combined equilibrium pressures of CO and CO2 from the reactionsFeTiO3 + C = Fe+ TiO + COand200 = C+ CO2reach 1 atmosphere.This report gives results of small-scale tests of selective reduction by carbon of the iron in titaniferous iron ores, both with and without addition of sodium carbonate. It is shown that the bulk of the iron may be reduced and separated without serious reduction or loss of titanium. Three Wyoming ores, Iron Mountain, Shanton, and Taylor, wore studied. The principal factors investigated were temperature, time, carbon:ore ratio, particle size, and sodium carbon ore ratio.Two methods of investigation were employed. In the first, intimate mixtures of ore and carbon were roasted and the reduced iron and titanium evaluated by leaching with dilute sulfuric acid and analyzing the leach solution (and, in some instances, the dried residues).Twenty grams of ore were mixed thoroughly with carbon and tamped into an alundum thimble having a loosely fitting cover. The thimble and contents were placed in a test-tube end porcelain tube and heated to the desired temperature in a Globar tube furnace. The open end of the porcelain tube was connected to a bubbler containing sulfuric acid, in a manner that permitted complete shut-off of the tube when desired. This allowed removal of the tube from the furnace at the end of the roast period without exposure of the contents to the atmosphere."

Jun 1, 1946

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

By J. Bakken, M. Th. Jonsson, G. Sævarsdottir

A typical three-phase submerged-arc furnace for production of silicon metal and ferrosilicon has arc currents ~100 kA, phase voltages ~100 V and total furnace power ~10 - 60 MW. The arcs burn in gas filled cavities or "craters", where the main atomic components of the plasma mixture are silicon, oxygen and carbon. Two quite different simulation models for high-current AC arcs have been developed: the simple Channel Arc Model (CAM), and the more sophisticated Magneto-Fluid-Dynamic Model (MFD). These models have been described extensively and results reported at INFACON-8 and INFACON-9, respectively. The coupling between the arcs and the AC power source is described by a complete three-phase Electric Circuit Model. Recent numerical modelling studies of industrial AC arcs show that the boundary conditions at the cathode and anode are critical for the simulation results. A novel Cathode/Anode Sub-Model for high-current AC arcs that treats both cathode and anode indicates a completely different cathode behaviour than previously assumed. A cathode spot which serves a high-current electric arc is shown to be dominated by the energy impact from the arc. This leads to lower cathode fall voltage than obtained from previously developed models. The anode fall voltage is negative, as the main function of the potential barrier is to repel plasma electrons. The cathode spot is diffuse in the sense that the arc in fact contracts away from the cathode. Simulation results are compared to measurements on both industrial furnaces and smaller scale pilot furnaces. An important conclusion, supported by our arc studies, is that the arc length in silicon metal and ferrosilicon furnaces does not exceed 15 cm and the arc may burn anywhere on the electrode, not necessarily beneath the electrode tip.

Jan 1, 2004

By Harry Siewert

"The commissioning of the 4th concentrator (C4) at Freeport Indonesia in early 1998 increased total mill throughput from 130k to 230k tonnes per day. The C4 flowsheet consists of a single 38 ft diameter SAG mill, four 24 ft diameter ball mills followed by four banks of 4,500 ft3 WEMCO flotation cells.The design of the C4 rougher flotation circuit was based on the expectation that the copper and gold recoveries achieved with the 4500 ft3 flotation cells would be equivalent to or better than that achieved with the 3,000 ft3 flotation cells in the 3rd concentrator (C3) rougher circuit. This assumption was due to the fact that the C4 flotation feed size would be less than 15% +212 microns compared to the C3 rougher flotation feed size of less than 23% +212 microns. By mid 1998 it had become apparent that the C4 rougher flotation copper and gold recoveries were below those predicted.In order to determine the cause of the lower recoveries, stage by stage rougher flotation surveys were performed in all four concentrators. The results of the surveys showed that the C4 rougher flotation circuit had a lower recovery of +200 micron material than that achieved in the C 1, C2 and C3 concentrators. Through mineralogical analysis, it was determined that a majority of the copper contained in the +200 micron fractions was liberated and recoverable. This paper describes the steps taken to increase coarse particle recovery, overall plant recovery and the results achieved."

Jan 1, 2001

By Jie-Liang Wang, Yongdan Cao, Zhao Cao

"The effect of ethylenediamine tetraacetic acid (EDTA) on flotation separation of fluorite from bastnaesite and its selectively depression mechanism on fluorite were studied by single mineral flotation, artificial mixed minerals flotation, solution chemistry analyses, Zeta potential and XPS measurements.The results show that fluorite can be deeply depressed by EDTA while the flotation of bastnaesite is almost unaffected when octanohydroxamic acid (OHA) is used as a collector. The separation index (SI) between bastnaesite and fluorite increases with the dosage of EDTA, SI can be raised from 1.18 to 12.66 when EDTA dosage increases from 0 to 2×10-3mol/L.Solution chemistry analyses show that EDTA is able to convert the Ca(OHA)2 hydrophobic precipitation on fluorite surface to a soluble Ca-EDTA complex but cannot complexly dissolve the Ce(OHA)3 precipitation on bastnaesite surface. Therefore, the Zeta potential of OHA conditioned fluorite can be reduced significantly by EDTA while the reduction degree to Zeta potential of bastnaesite is relatively low. XPS measurement shows that EDTA removes the chemically adsorbed OHA from fluorite surface but has little effect on the adsorbed OHA on bastnaesite surface. As a result, fluorite can be selectively depressed by EDTA in bastnaesite flotation, which behaves an important industrial application prospect in rare earth ore flotation.INTRODUCTIONNowadays, Rare earth elements (shortened as RE) and compounds are of significant importance for a range of rapidly expanding industrial applications including catalysis, metallurgy, renewable energy, and special materials due to their unique electrical, magnetic, optical and chemical properties [1]. The seventeen RE elements, including the lanthanide-group fifteen elements, yttrium and scandium, could be divided into three groups, i.e., light, medium and heavy RE elements based on the different solubility of RE sulfates [2]. Bastnaesite ((Ce,La)CO3), containing approximately 75% REO, is one of the most important light RE minerals [3]. Flotation is the common method to recover basetnaesite [4-6]. Nonetheless, basetnaesite is often associated with calcium-bearing gangue minerals such as fluorite, and the separation of basetnaesite and fluorite by flotation is usually difficult due to their similar surface properties and therefore floatability [7-9]. Therefore, research on high selective flotation reagents of bastnaesite over gangue minerals has attracted a lot of attention [10]."

Jan 1, 2018

By Earl Oliver

SEVERAL notable papers, and free discussion on many controversial subjects, marked the various sessions of the Petroleum Division at the annual meeting. The Division first convened on Tuesday afternoon, Feb. 16, and wound up with a dinner and technical meeting on Thursday night. H. C. Fowler presided at the opening session, which was devoted to problems of engineering research and production engineering. Joseph Chalmers abstracted his paper on the flow of air and gas through porous media, in the preparation of which E. L Rawlins and D. B. Talia-ferro contributed. G. H. Fancher told how much he and his associates at Pennsylvania State College were interested in this field, and described the problems they had met in conducting test work. He made a plea for standardization of testing methods. Mr. Fowler then read an abstract of written discussion by Professor Barb, which was followed by discussion by Dr. Fancher and Mr. Chalmers of technical points in connection with the Chalmers' paper. H. H. Hill abstracted written discussion from Messrs. Wilde and Moore, of the Humble company. The second paper, by K. B. Nowels, on computing pressure drop in the pipe of flowing oil wells, was abstracted by the author. Messrs. Blair Smith, G. W. Coggeshall, and I. I. Gardescu participated in the discussion, and the chairman abstracted written discussion prepared by Mr. Rawlins. Most of this had to do with the viscosity of gas¬oil mixtures, on which subject Mr. Nowels said there was great need of accurate technical information.

Jan 1, 1932

By D. Harrington

Although the explosion-fatality record for the fiscal year 1944 showed considerable improvement over those of the preceding 4 years, it is still fur from creditable, and the coal-mining industry and agencies interested in the prevention of coal-mine accidents should not be satisfied until accidents from explosions and fires are eliminated. In view of present knowledge of the methods of preventing explosions and fires, such disasters are inexcusable and discredit the mining industry. Despite this knowledge, far too many coal¬mine operators and employees continue to follow procedures that have resulted in disasters in the past. Included in the appendix to this circular are a number of safety measures designed to prevent coal-mine explosions and fires and metal-mine fires. Their adoption is essential if explosions and fires are to be prevented, as certainly they should be. An epidemic of disastrous mine fires of electrical origin during the past 2 years emphasizes the need for better methods of protection of underground electrical circuits. At present, committees of mining-electrical engineers, electrical-equipment manufacturers' representatives, and others are cooperating with the Bureau of Mines seeking means to solve this problem.

Jan 1, 1945

By Henry J. Sandri

The use of economic models for forecasting purposes is an inexact yet necessary tool for mineral decision making. One method not commonly used is cyclical analysis because of its "non-scientific approach". However, under certain circumstances a modified cyclical approach can provide useful insight to mining companies. The current paper discusses mineral modeling, the type of economic models and the use of cyclical forecasting for mining firms (not speculators) involved in precious metals.

Jan 1, 1984

By Thierry Bernard

This case study shows how a unique combination of field measurements and advanced technologies allowed blasters designing, loading and firing an incredibly challenging quarry blast.

Jan 1, 2015

By Francis J. Arland

The installation of augered cast-in-place (ACIP) piles requires careful quality control to assure a successful pile installation. Unlike steel, pre-stressed concrete or other types of driven piles, which are shop fabricated, delivered to the site and typically driven to a minimum tip resistance, augered cast-in-place piles are installed to a pre-determined tip elevation or to a refusal criteria. The structural section of the ACIP pile is constructed during pile installation and cannot be inspected prior to installation. Therefore, a carefully administered quality control program is essential to a pile foundation that will meet or exceed design requirements. This requires an experienced team consisting of the Geotechnical Engineer, Contractor and Inspector. The focus of this paper is to discuss the responsibilities and duties of the ACIP piling Inspector. Qualifications of the Inspector The qualifications of the inspector are related to the complexity and difficulty of the proposed project. Ideally, the Inspector should be an individual with a degree in civil engineering with special emphasis in geotechnical engineering. A properly trained technician with geotechnical engineering experience working under the direct supervision of a geotechnical engineer may be able to provide competent inspection on some projects. It is important that the Inspector have a good understanding of subsurface and ground water conditions and how they will affect pile installation. The Inspector must understand ACIP pile installation procedures and be able to communicate with the Contractor, Structural and Geotechnical Engineers; and maintain a detailed pile record for each installed pile.

Jan 1, 1997

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By C. J. Van Niekerk

The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the grain boundaries during welding. In the 2 mm plate sensitization occurred in the heat input range of 0.1 kJ/mm to above 0.25 kJ/mm and in the 4 mm plate sensitization occurred in the heat input range of 0.2 to 0.9 kJ/mm. Ti stabilization is ineffective at the heat inputs used in this investigation due to the rapid cooling rate through the temperature region where TiC precipitates. The presence of N was found to be detrimental since it consumes Ti on cooling, forming TiN, effectively lowering the amount of Ti available for TiC formation during rapid cooling after welding. Annealing for 5 minutes at 725°C does not improve the sensitization characteristics of the welded plate. There is a linear increase in grain size as heat input increases. The resistance to pitting corrosion decreases in the sensitized, welded plate in theheat-affected zone adjacent to the fusion line of welding. Keywords AISI 409 ferritic stainless steel, sensitization, grain growth, resistance to pitting corrosion, low heat input welding.

Jan 1, 2011

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By J. R. Thoenen

IN five years mineral wool has grown to a thirty-million-dollar industry from one whose output was valued, in 1933, at $1,700,000. Ten years ago, in 1928, there were only seven producing companies, with an annual output of but 50,000 tons. By 1936 fifty or more companies were producing half a million tons. The industry is still growing vigorously and will profit from the expected activity in building in 1339, for two-thirds of this material is used for building insulation and to assist in fire-retarding, in both new and old homes. It is as useful in the South, to protect against heat, as in the North, to keep out the cold, if one may speak nontechnically. It is a concomitant of air conditioning, that new addition to the American standard of living that began in theatres, department stores, and railroad dining cars, and is rapidly progressing down to small homes. Here, then, is an industry that is only beginning to have a present, and one with an almost certain important future; one that depends upon mining and the by-products of mining for all of its raw materials; one that every progressive mining man should know something about.

Jan 1, 1939