Search Documents

By K. R. Becker

The addition of a force gage and a reaction detector to the Bureau of Mines drop-weight impact apparatus made it possible to examine the details of the force exerted on the specimen and make estimates of the time to reaction. With the current setup the force was found to be oscillatory and not reproducble. However, single well-defined pressure pulses can be delivered to the explosive sample by modifying the drop-weight tools. With a modified test arrangement, the time to reaction and the peak force and energy at the time of reaction were determined as a function of drop-weight height for several different explosives. All these parameters were found to decrease as the rate of force application was increased. The same parameters were also found to vary with the thickness of the test sample. The implications of these results are discussed in terms of practical drop-weight testing.

Jan 1, 1972

By D. B. Rebuli

Seismic networks in deep gold mines of South Africa are often planar owing to the tabular geometry of the orebody and, therefore, the mining infrastructure. Consequently, seismic event locations are poorly constrained in the direction perpendicular to the reef plane, and symmetrical locations above and below the reef plane may fit the observed data equally well. This problem may be resolved in situations where the strata above and below the reef plane have significantly different seismic velocities, which is the case for the Ventersdorp Contact Reef at Kusasalethu mine (previously Elandskraal, the amalgamation of Deelkraal and Elandsrand). A location method using a layered location model that takes into account the velocity contrast between the layers was tested. Observed direct- and head-waves were used to determine the velocity bounds of the P-wave velocities in the two-layer model. The data-set was also used to find the best P- and S-wave velocities for the two layers by grid searching over a range of velocities and minimizing the sum of the travel-time residuals. The results from the grid search and those from the calibration of velocities using direct- and head-waves give similar P-wave velocities for each of the two layers. A second set of seismic events was then relocated with this layered model and locations closer to reef were found. This simple layered location method goes some way to reduce the reefperpendicular location errors for Kusasalethu mine in particular. Keywords mine seismology, velocity model, location methods.

Jun 1, 2013

A way back in 1851-2 an army of diggers had commenced the conquest, of the now famous goldfields of Australasia. At that time, and in the Colony of Victoria, more that 10,000 were camped on and around the slopes of the silurian ridges over which Ballarat East h'as been built. A wonderfully rich golden harvest was soon gathered from the alluvial found high on these slopes, and from runs (or gutters) which got their rise on them, and were traced down gullies into a broad valley. In due course it was ascertained that the valley carried a main gutter which represented the unity of the higher ones, and further explorations proved this gutter to have a westerly and then a southerly trend toward and under a basaltic plateau, on the top ofwhich Ballarat West and Sebastopol now stand. In the records of alluvial gold mining all the world over the Ballarat field can be classed amongst the richest. Gold in pieces the size of beans, in, stringy filigree bits, in dust and in solid lumps (the largest of which weighed more than 2,200 ozs.), was obtained in the comparatively shallow ground on the slopes; and speaking generally, great and uniform richness was met with along a belt of country on which, in a north and south line, the present quartz mines of Ballarat East are at work. It was noticed by the diggers that when the gutters crossed the upturned edges of the ,strata, the gold deposits in them were patchy, and that when they trended north and south on this beltthey carried rich deposits for longer distances. In time it was also noticf!d that a class of stringy, irregular shaped quartz occurrences, in a bottom of soft slates, in the, immediate vicinity of tpe g)ltter, meant greater richness, and (in the aIluvial) on the higher ground slabs of quartz would now and then be met with, in which strings and spongy masses of gold were found. As the shallow alluvial became worked out the diggers turned their attention to the quartz occurrences, and, now and again the striking of a flat make of a very golden nature would cause quite a stir in the local mining world.

By Kosuke Hosoda, Shuji Owada, Hiroyuki Tokuichi, Hirobumi Ohta, Chiharu Tokoro, Moto-o Sato, Katsushi Okumura, Hiroto Ogawa, Hideaki Umezawa

The Japanese government enforced the "Small Domestic Appliances (SDAs) Recycling Law" in 2013. The law targets metals such as Ta, Nd, Dy, Co, and W to be recycled. Considerable amounts of these minor rare metals are mounted on printed circuit boards (PCBs) of the SDAs and/or e-scrap (electric and electronic scraps). Although precious metals and copper can be recovered from the e-scrap in non-ferrous metals smelters, most of the minor rare metals report to the slag in these smelters in non-recoverable forms. These metals are often used in particular types of devices, and therefore it is possible to concentrate them by separating such devices before feeding to the smelters. In previous work we developed technology for "Device Separation" to concentrate several minor rare metals, but some problems remained, such as how to remove the PCBs from e-scrap bodies, and how to detach devices from PCBs after their removal from escrap bodies. This paper proposes a two-stage crushing process in which, firstly, PCBs are removed from the e-scrap body with various crushers, and secondly, devices are detached from the PCBs involving the application of elevated temperatures. It was found that in the first stage, crushers with physically flexible rotating media such as chains, which provide high collision probability with the sample and consume relatively low energy, can quite effectively separate the PCBs from the e-scrap bodies non-destructively. In the second stage, heating was found to be remarkably effective in helping to detach mounted devices from PCBs, also non-destructively. This paper will also discuss the detailed mechanism of the heating effect on the detachment of devices from PCBs.

Jan 1, 2014

By James P. Ulery

In This Chapter [Geologic features associated with anomalous methane emissions Gas outbursts and blowers Methane drainage strategies for mitigating anomalous methane emissions and General considerations for a methane drainage program] This chapter summarizes how certain geologic features may be associated with unexpected increases in gas emissions during coal mining. These unexpected emissions have the potential to create explosive conditions in the underground workplace. Also discussed are the generally used practices to alleviate potential hazards caused by gas emissions associated with these geologic features. INTRODUCTION Unforeseen mine gas emissions in quantities sufficient to create hazardous conditions have been attributed to sources outside the mined coalbed since the first documentation of methane explosions in coal mines [Payman and Statham 1930]. Geologic features such as faults have long been recognized as conduits for gas flow from strata adjacent to mined coalbeds [Moss 1927; Payman and Statham 1930]. Other features such as sandstone paleochannels, clay veins, and localized folding have also been recognized for their impact on gas emissions into mine work-ings [Darton 1915; Price and Headlee 1943; McCulloch et al. 1975; Ulery and Molinda 1984]. The fact that strata adjacent to mined coalbeds can emit large quantities of methane gas into mine workings is not surprising from a theoretical perspective. Many researchers have recognized that during the burial and diagenesis of the organic matter forming today’s minable coalbeds, similar dispersed organic matter in adjacent strata has produced methane in quantities far exceeding the storage capacity of the coal and surrounding rock [Juntgen and Klein 1975]. It is not surprising then that large quantities of methane can remain trapped in these strata. A potential hazard occurs when mining of a nearby coalbed causes pressure differentials and mining-induced fractures conducive to gas flow into the mine workings from these strata. This gas flow may be facilitated or temporarily impeded by the presence of geologic structures or anomalies.

Jan 6, 2006

By H. L. Willett

Wrapping up the symposium, covers incidence of spontaneous combustion in British mines, assessment of liability to spontaneous combustion, precautions, rate of advance, starting a line of a coalface, local heatings at roadsides, burying packs, coal headings, retreating longwall, detection and sealant coatings.

May 23, 1905

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By L. O. Thomas

THE Alaska Highway, in its course through British Columbia, traverses parts of two great physiographic divisions of Canada which are also distinctive geologically-the Cordillera in the western section and the Interior Plains in the eastern. The Cordilleran region in the portion of the Province with which this paper deals can be divided into four major northwest systems, known respectively from west to east as Coastal, Plateau, Cassiar-Omineca, and Rocky Mountains. The Coastal system consists solely of the Coast range except in the extreme northwest, where a part of the St. Elias range is included. The Coast range, characterized by mountains of great ruggedness,. is made up of an igneous complex of granitic rocks intruded chiefly as a great batholith. In places, spurs of these rocks extend into the Plateau heft, a partly mountainous tract largely occupied by quartzites, quartzose mica schists and their gneissic phases, and crystalline limestone with interbands and broad areas of chlorite, _hornblende, and sericite schists and bodies of intrusive granite gneiss-an assemblage of rocks known as the Yukon group. The Cassiar-Omineca system marks the divide between the Pacific and Arctic drainages. Its eastern boundary is well defined in the south by the Rocky Mountain Trench (see p. 229). The rocks of the system are, miainly, highly altered Palaeozoic sediments, but there are also Precambrian and Mesozoic rocks, the latter largely volcanic. The core of the system is granitic and there is evidence (see p. 221) to support the belief that it is of such a length as to constitute a batholith comparable to that of the Coastal system.

Jan 1, 1944

By Glenn Norris, Tyler Buckingham

"Gold recovery gains in the order of one to two percent have been realized in 2009 due to changes in the operation of the grinding circuits at Barrick Gold Corporation’s Hemlo - Williams Mill. The initiative known as “split milling” involves milling low grade open pit ore in one grinding circuit and higher grade underground ore in the other grinding circuit under different conditions.The philosophy of split milling involves processing higher grade underground ore at a lower throughput rate and a finer grind while milling lower grade open pit ore at a higher throughput rate and a coarser grind. Bench scale tests showed that the recovery relationship for underground ore sources was much more grind sensitive than that of open pit ore. This relationship proved to hold in the plant. The gold recovery gain due to finer grinding of the higher grade ore is much greater than the recovery loss due to coarser grinding on the lower grade ore. Since the majority of gold is being recovered at a higher rate, this results in higher overall plant gold recovery when compared to the traditional operation philosophy of blending the ore sources.The challenges for achieving the maximum benefits of split milling were two fold; the need to increase throughput on the open pit ore milling circuit and a means of grinding finer on the underground circuit. The former was met with an increase in SAG (Semi-Autogenous Grinding) mill ball charge, a basic “drill to mill” blasting campaign and changes to the primary gyratory crusher. The latter was met with a reduced SAG mill ball charge and a higher milling density. The resulting benefits in additional gold recovered are in the order of $3-5 million per annum.INTRODUCTIONThe Williams Mill processes ore from three different ore sources, the David Bell Mine (DB), the Williams Underground Mine (WUG) and the Williams Open Pit (OP). All three ore sources are located within the Hemlo camp in Northwestern Ontario adjacent to the Trans-Canada Highway. The Williams Mill was built in the mid 1980’s at which time it was designed to process 3,000 dry metric tonnes per day through a 22’ SAG mill in series with a 16’ ball mill. In 1988 a Mill expansion doubled the mill capacity by adding a second identical grinding circuit. A photo of the current grinding circuit can be seen in Figure 1. Today the Williams Mill processes an average of 8,000 tonnes per day of which approximately 60% is from the Williams Open Pit."

Jan 1, 2010

By R. Poisel, C. Scavia, Preh A., W. Roth, M. Pirulli

ABSTRACT: Two methodologies for the three-dimensional simulation of the run out of rock avalanches are presented: one based on a granular approach and the other based on a continuum equivalent approach. An evaluation of the possible run out area of the Oselitzenbach landslide (Carnic Alps, Austria) has been carried out applying the two methodologies. The combined use of these two approaches makes it possible a comprehensive assessment of the run out area. RESUME: Deux méthodologies pour la simulation tridimensionnelle de la propagation des avalanches rocheuses sont présentées: la première est basée sur un modèle de type granulaire et la deuxième sur un modèle du continu équivalent. Une évaluation de la propagation éventuelle de l’avalanche de Oselitzenbach (Alpes Carniche, Autriche) a été réalisée en utilisant les deux méthodologies. Les résultats obtenus montrent que la combinaison des deux approches rend possible une analyse plus complète de la phase de propagation. KURZFASSUNG: Für die dreidimensionale Modellierung eines Felsmassensturzes (sturzstrom) werden zwei Methoden, eine granulare und eine kontinuumsmechanische Methode, vorgestellt. Beide Methoden wurden zur Abschätzung der Ausbreitung (runout) der Massenbewegung Oselitzenbach (Karnische Alpen, Österreich) herangezogen. Die kombinierte Anwendung beider Methoden ermöglichte eine umfassende Beurteilung des möglichen Ausbreitungsbereichs.

Jan 1, 2003

By Edward A. Barrett, Roberta A. Calhoun

MORE THAN 30 MILLION EMPLOYEES each year are exposed to hazardous occupational noise, and approximately one-third of them develop permanent hearing loss (NSC, 2000). Possible explanations for the latter statistic include worker regard for noise as a mere nuisance rather than as an occupational safety and health hazard, and consequent neglect of established protective measures (e.g., hearing protection); lack of knowledge concerning noise; improper use of hearing protection; worker indifference; and inadequate training (Bauer & Babich, 2004). Many drill rigs generate high sound levels, which vary according to the type of machine, its location with respect to the physical surroundings, and the location of the sound measured around the rig. A NIOSH study measured noise output from several types of drill rigs during field investigations (Ingram & Matetic, 2003). Two types of data were recorded the actual noise generated by the drill rig at various positions around the rig and the noise to which the drill operator was exposed during the drilling cycle. For the latter, sound level measurements up to 120 dBA were recorded while hammering casing (metal on metal) in drilling a water well (Photo 1). Several types of administrative controls exist to address worker exposure to loud drill rig noise. Rotating duties to decrease exposure time and posting warning signs in high-noise work areas are two such controls. Another is the use of hearing protection. Worker use of hearing protection has been disappointing, however. One study by the University of Michigan found that construction workers used earplugs and earmuffs only between 36% and 61% of the time that they were necessary (Lusk & Kerr, 1998). In a 2001 study, OSHA reported a relatively low rate of 30.4% for use of earplugs among construction workers (Walker, 2001). Why are rates for hearing protection use so low? One explanation may be workers' lack of concern for noise in the workplace. They expect workplace noise to be a loud and in¬ evitable nuisance and, therefore, accept it as part of the job. As a result, they disregard proven measures that can protect their hearing. Other workers may use hearing protection, but do so improperly. They may misguidedly remain in high-noise areas for extended periods thinking they are protected when in fact they are not. Other reasons for low use and/or misuse of hearing protection include poor education, lack of awareness and inadequate training (Nash, 2003). To address the training issue, NIOSH developed two exercises from which drillers can learn about noise, hearing loss and hearing protection. The first is an invisible ink exercise, titled "Drill Rig Incident" (DRI) (Photo 2); the second is a 3-D slide reel training aid, "Wearing Hearing Protection Properly" (WHPP) (Photo 3). DRI is an instructor-

By H. L. Bibbs, H. D. Snedden

"INTRODUCTION The use of beryllium and its alloys has increased rapidly during the last decade. Further expansion of its use is limited; in part, by lack of adequately developed ore reserves. The principal commercial beryllium mineral is beryl, which is found chiefly in pegmatites and produced for market as a byproduct of the mica and feldspar industries. The coarse beryl is mined selectively, sobbed and sorted by hand, and then sold without further beneficiation. The known reserves of coarse beryl are small. No method has been available for concentrating small disseminated beryl crystals, so ores of this type have not been mined or have been left on waste dumps. Disseminated ore in low-grade unmined areas and waste dumps on developed properties is a potential source of beryl, provided a method is developed for its beneficiation.Published literature on the concentration of beryl is lacking in detail or deals chiefly with tests on artificial mixtures of pure minerals, and procedures as given were not applicable to the beryl ores tested at the Salt Lake Station. The testing procedures described in this report are independent developments. By employing these procedures, beryl was satisfactorily con¬centrated from several run-of-mine and dump ores, although these ores wore low in grade and part of the contained beryl was finely crystalline and disseminated.Beryl, quartz, and feldspar, when ground to flotation sizes, are so alike in color and general appearance that they cannot he distinguished by visual observation. The progress of the work depended on rapid determination of the grade of test products by means of the petrographic microscope. Small samples of concentrates and tailings were often cut after each addition of reagents, dried, and examined under the microscope."

May 1, 1947

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

By J. F. Shaw

MINE fires are usually extinguished by constructing seals in the approaches to the areas to exclude air from the fire areas, which smothers the fires in an oxygen-depleted atmosphere. Seals should be substantially constructed and made as nearly airtight as possible and should be provided with a sampling pipe so that samples of the atmospheres behind the seals may be collected at regular intervals. Methods of constructing seals and of sampling and analysing mine atmospheres are fully described in Bureau of Mines publications. (1, 2). Information obtained on the composition of atmospheres behind fire seals is helpful in determining if a fire has been extinguished or if there is any danger of an explosion when a fire area is being sealed or unsealed. The progress of a mine fire can best be determined by studying percentages of carbon dioxide, carbon monoxide, and hydrogen in the atmosphere behind the seals. Hydrogen will be formed in a bituminous- or subbituminous-coal mine when the temperature exceeds 480° F. and in an anthracite mine when the temperature exceeds 660° F. (3). Carbon monoxide and carbon dioxide are both products of combustion of coal, wood, or other organic compounds. The presence of carbon monoxide has long been accepted as an indication of a mine fire. A sealed fire area should not be reopened until the carbon monoxide has disappeared. Trends in the percentage of carbon dioxide are also useful in determining the status of a mine fire. Carbon dioxide is sometimes liberated by rock strata. In this case, carbon dioxide in the atmosphere behind a seal will be from two sources-the rock strata and the fire. When the, fire is extinguished, carbon dioxide will be liberated from only I source, the rock strata, and when the percentages of carbon dioxide are plotted, the slope of the curve will not be as steep as when this gas was being liberated from 2 sources. If the only source is the fire, the percentages of carbon dioxide will gradually decrease after the fire has been extinguished. By studying analyses of a mine-fire atmosphere, it is possible to determine if the atmosphere is explosive; if the mixture is capable of becoming explosive when mixed with air; and if the mixture can be made nonexplosive or be prevented from becoming explosive by being mixed with an inert gas. These factors can be computed mathematically or determined graphically. The mathematical calculations advanced by Ash and Felegy (7) are discussed, and graphical solutions of their equations are presented. It is believed that the graphical solution will be extremely helpful in determining the characteristics of a mine-fire atmosphere when fighting a fire, because the results can be obtained in a matter of minutes, and there is less likelihood of an error being made under the stress incident to control efforts. The experimental and theoretical work upon which the formulas are based have been adequately described and are not discussed at this time (5) (6).

Jan 1, 1955

By Shu Yamaguchi

The behavior of halide impurities in pyrometallurgical processes such as Wealtz kiln and MF process has been discussed based on the thermochemical data and the reported data of PbO activity in PbCl2-PbO melts. The role of PbCl(g) has been estimated to be significant in the chloridization evaporation reaction. From reported data on the PbO activity in PbC12-PbO melts, activity of PbCl2 has been calculated by the numerical integration of Gibbs-Duhem equation, and the stability domains and the composition of the liquid phase as well as the vapor pressure of PbCl2 have been estimated as functions of log P2HCI/PH2O and temperature. From the discussion of the path during cooling process on the log P2 HCI . PH2O vs. temperature diagram, the authors proposed a possible dechioridization process that utilize water vapor as a dechloridizer for the direct precipitation of PbO from gas phase.

Jan 1, 2003

The panic bars (and associated linkage's and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on Self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and soma commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By T O&apos, Sullivan

Reconciliation of metal production from a sublevel cave (SLC) mining operation is a complicated process. SLC reconciliation is unlike reconciliation for open stope operations, where a tonnage of extracted ore can be assigned to an exact volume of in situ ore, and a direct comparison made between the estimation of contained metal and actual metal production. In SLC operations the ore extracted from a particular SLC drawpoint will be composed in part from the parcel of freshly blasted in situ material, in part from varying components of ore material (from cave stocks) flowing down from other previously mined areas vertically above the current draw position and in part from external dilution. This leads to difficulties in reconciling production grades against estimated grades. The problem is that we know how much metal we have produced but we can not precisely say where it has come from. Metal production reconciliation is fundamental in assessing ore reserve estimation accuracy and performance and in determining a draw management strategy for SLC mining. In terms of contained metal, differences in extracted metal compared to in situ metal represent changes to cave stocks. To generate local estimates of the cave stocks, differences in metal for each ring are treated as additions to or subtractions from a series of vertical columns of stocks extending throughout the height of the cave. The sum of metal differences (extracted versus in situ) for each vertical column results in a residual metal map at any particular mining level. The metal maps show areas where the metal production has been greater than or less than expected. The maps also highlight areas in the cave where residual metal is located, areas where targeted overdraw can reduce cave stocks.

Jan 1, 2006

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By S. A. Scott

Mintek developed the MinataurTM leach-solvent extraction-precipitation technology as a cost effective, easily operated alternative to conventional gold refining processes. The technology was first commercialized at the Harmony Gold Refinery in 1997 to produce 99.99 per cent gold product and has subsequently led to development of various value-addition steps including the casting of various investment bars, gold wire drawing and gold potassium cyanide powder production. In addition to refining gold to high purity, if an appreciable amount of silver is present in the feed material it is also refined to 99.99 per cent purity. The major advantage that the Minataur? technology has over other gold refining processes is the relatively low gold lock-up and reduced operating costs. The operating cost1as at April 2001 for the expanded Harmony refinery (24-ton per annum gold production) was approximately half that of conventional smelting and toll refining. The extractant employed for solvent extraction is relatively cheap and highly selective for gold, making the technology attractive in situations where significant quantities of platinum group metals or base metals are present.

Jan 1, 2004

By L. S. Bicalho, W. J. Rodrigues, P. M. A. Rollo, P. R. G. Brandão, W. C. da Silva

Quadrilátero Ferrífero is an important mineral province located in Minas Gerais state, responsible for a substantial amount of iron production in Brazil. Among the concentration methods for iron ore practised by the mining companies in this region, the most important is the reverse cationic flotation. Dolomite iron formations, with the presence of hematite, quartz and dolomite, occur in several areas of mining and, with the deepening of the deposits, this type of ore, with low iron content and more complex mineralogy occurs frequently. Carbonaceous minerals, mainly dolomite, present a technological challenge for the concentration of iron ore by flotation. In the present study, the concentration of iron ore with 6% of dolomite content was evaluated. Bench flotation trials indicated that conventional iron ore flotation is not selective to float dolomite, thus compromising the iron content in the final concentrate. Alternative flotation routes were evaluated, and a selective condition was reached to float both quartz and dolomite using the combination of the cationic collector Flotigam 16424 with an anionic collector Flotinor 16551. It was demonstrated that the flotation of dolomite was improved with the combined use of both collectors in the cleaner stage, and by a previous quartz flotation in the rougher stage. Zeta potential analysis indicated specific adsorption as the adsorption mechanism between Flotinor 16551 and dolomite, confirming the high selectivity observed in the bench flotation tests. Keywords: Flotation, iron ore, dolomite

Jan 1, 2020