Search Documents

By Zhibao Li, Kunming Zhai, Yan Zhang

The hydration kinetics of MgO, namely magnesia or magnesium oxide, obtained by calcination of magnesite MgCO3 or synthetic MgCO3·3H2O has been studied. Nesquehonite (MgCO3·3H2O) was prepared by the reaction of MgCl2 with Na2CO3 in a mixed-suspension mixed-product removal (MSMPR) crystallizer at 40 °C. Three magnesium oxide samples were obtained by calcination of magnesite MgCO3 or synthetic MgCO3·3H2O in muffle furnace at 900, 1100 and 1300 °C for 3 h, respectively. The hydration experiments of MgO samples were investigated at 25, 35 and 45 °C for 24 h in a stirred batch reactor. The hydration results indicate that the rate and extent of hydration of magnesia decreased remarkably with hydration temperature and increased with decreasing calcination temperature at a constant hydration temperature. The whole hydration reaction of magnesia was supposed to experience the promotive period and declining period. An empirical kinetic model ( k t p -?ln(1-??) ??) and a modification of the classical shrinking core model for diffusion control ( k t b d -?-?3 2 ????1 [1 (1 ??) ] ) have been applied to fit the experimental data of hydration in two stages, respectively. The values of kinetic parameters ( p k and d k ) were obtained by regression analysis and the activation energy of the sample at 900 °C was estimated to be 34.23 kJ/mol. The comparison between MgO from calcination of synthetic MgCO3·3H2O and a commercial MgO used in silicon steel production was carried out, indicating that special silicon steel grade MgO can be obtained by calcination of MgCO3·3H2O below 900 °C.

Jan 1, 2014

Resources and reserves are critical inputs into the determination of an operating mineÆs financial results and balance sheets, but how well understood is this fact. Do the investors, directors, accountants and geologists/engineers responsible for preparing or relying on relevant aspects of the end results properly understand the inputs and outputs and the associated risks that may be established. The first step is to understand how financial reports are impacted. The most obvious, and best known, impact is in the calculation of depreciation and amortisation charges against long term assets. In addition, however, there is a requirement to regularly determine whether asset book values are impaired û this is nearly always performed globally by the preparation of a discounted cashflow model for a mine which is usually based on a mine life as determined from the resource and reserve statement û the particular driver here is normally the short and long term production plans. A key aspect of the short term production plan is that it would normally not assume that the reserve and resource statement implies consistent grade, stripping ratios, etc. However, outside of the early years of a plan, more generic assumptions of these variables are often made in conjunction with the reserve and resource statement. Depending on the timeframe of the detailed production plans, this can have a large impact on a projectÆs net present value. Other financial balances that may also be impacted include restoration and rehabilitation provisions, retrenchment provisions and deferred or equalisation stripping accounts. The age old question of whether all reserves should be used or whether some or all of the resources should be included for financial reporting purposes has never been adequately resolved. It is our view that there should be no prescriptive answer to this question but judgement of all professionals involved in the process needs to be included. Furthermore, the company needs to be able to support their conclusions with well thought out and appropriate answers. This may not be in line with the approach that certain accounting standard setters may be proposing or taking, and this paper will outline the current status of global requirement and the likely future directions. Whether reserves or resources are utilised, does not change the key requirement that those preparing or using reserve and resource statements need to understand key aspects. For example: geologists/engineers do they know how reserves or resources will be used? have they imparted information on variability of key drivers such as grade or depth or dilution? do they know that major financial/business altering decisions may be made based on the analysis? accountants do they understand where the numbers have been derived from and the assumptions that may have been made in their determination? do they understand the degree of accuracy (or inaccuracy) that may exist particularly with resources)? do they understand the history of resource reconciliations and what it may mean for the future? directors do they understand the processes undertaken by the company to prepare the financial report and the interaction between the geologists/engineers and accountants? do they understand the potential sensitivity of results to the input variables? Financial reporting is extremely reliant on the use of the reserves and resources, however, the geologists/engineers, accountants and directors do not always understand the interactions between themselves which may lead to misleading public reporting. More education and communication between various parties is needed.

Jan 1, 2002

By R. G. Church

Belle Ayr Mine was established in 1972 as the first large surface coal mine in the Powder River Basin of Wyoming. During the mid-1980s, it was eventually out-distanced in productivity by newer mines, and management recognized that the mine must recapitalize its major mining equipment and enhance its workforce flexibility in order to be competitive in the deteriorating market situation. Therefore, state-of-the-art haulage and loading equipment was placed into service, and a 12-hour rotating shift and a technician-based workforce was implemented. Belle Ayr Mine is located 29 km (18 miles) southeast of Gillette, Wyoming, in Campbell County (Figure 1). The mine is a part of AMAX Coal West, Inc., and with its sister mine, Eagle Butte, located 8 km (5 miles) north of Gillette, is a major contributor to the overall coal production of AMAX Coal Industries, Inc., headquartered in Houston, Texas. This paper addresses mine planning, recapitalization initiatives, and innovative workforce changes which propelled this large, surface coal mine to the forefront of productivity in the ever tightening low sulphur coal market.

Jan 1, 1994

By G. W. Jones, R. E. Kennedy

"INTRODUCTION In the manufacture, storage, transportation, and use of combustible gases and vapors, explosion hazards, which at times may be present when air becomes mixed with the gases and vapors, become of primary importance. Such conditions are especially dangerous where large volumes of gaseous atmosphere are involved, because an explosion under such circumstances is capable of doing tremendous damage to both property and personnel.Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated, and published results dealing with, the explosibility of various types of combutible atmospheres. The explosion hazards of natural gases have received attention, and results giving the limits of inflammability and ignition temperatures in air have been determined and published. 4/ Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide. 5/Because of the increased demand for crude oil for war purposes, the application of secondary-recovery methods of stimulating oil production have received considerable attention during the last few years. The process consists in the injection of natural gas into partly depleted oil wells to cause the oil in the sands to flow into producing wells and so increase the amount of recoverable oil. 6/"

Feb 1, 1945

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By R K. W Merkle, S Madoom Hussain, T Yellappa

Cr-Ni-Cu¦PGE deposits are known to occur in early Archaean mafic-ultramafic rocks. Early Archaean mafic-ultramafic (MUMF) rocks occur in the western Dharwar craton and range in size from small pods to schist belts. These MUMF pods consist mainly of meta-peridotites, tremolite-actinolite schists, serpentinites, amphibolites and metabasalts. Spinifex, nodular and ocelli textures are also present. The rocks have been subjected to greenschist and amphibolite facies metamorphism. Geochemical studies were undertaken to evaluate the possible occurrence of economically important elements in the mafic-ultramafic enclaves around the major Arsikere-Tavarkere lineament and surrounding gneissic terrain adjoining local shear zones that occur as discontinuous pods between Arsikere and Chennagiri. Talc-serpentine and tremolite- actinolite schists contain chromite which is rimmed by ferrit-chromite. A notable feature of these MUMF rocks is that they exhibit high MgO (22 - 40 per cent), total iron (8.34 - 10.01 per cent), Ni and Cr (~3000, 2800 ppm) contents, with some samples showing komatiitic affinity. The rare earth elements (REE) data show slightly fractionated patterns with enriched LREE (LREE/HREE ~5.0) and negative europium anomalies. The Pt and Pd values reach 6500 and 191 ppb. The MUMF rocks, especially those exhibiting high chromium contents and occurring near shear zones, are potential hosts for economic platinum group element (PGE) deposits.

Jan 1, 2008

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

By Michael N. Greeley

The movement to reclaim abandoned mine sites has gained momentum as federal, state, and private organizations have increased their commitment and resources to tackle mutual, and often controversial, problems of health and safety. Numerous interorganizational agreements have been implemented to promote cooperation in the characterization of mine site hazards, development of mutually acceptable plans of remediation, and sharing of actual cleanup requirements. Working through these partnerships, the federal land management agencies have begun to focus on abandoned mine reclamation in selected, priority watersheds and other drainage basins. Although there are major difficulties to overcome, significant progress continues to be made.

Jan 1, 1999

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By Timothy W. Ellis

Wire Bonding is the dominant IC interconnection process presently used in the semiconductor assembly industry (1). The flexibility, adaptability and cost of wire bonding will continue to keep it as the key process for the interconnection of integrated circuits to substrates. However, wire bonding still has certain technological hurdles to overcome if it is to continue following the semiconductor roadmap (2). Particular issues which need to be addressed include low overall tensile strength, low elastic modulus, low shear per unit area and mechanical loop stability of Gold based micro-alloys. The ability to produce ?Deformation Process Metal-Metal Matrix Composites? (DMMCs) is based upon the deformation nature of immissible metallic systems. For reference, the Gold (Au)-Molybdenum (Mo) phase diagram is shown in Figure 1 (3). By inspection of the diagram, Au has a very low solubility for Mo, while Mo has essentially no solubility for Au. This is the metallurgical analog of oil and water. In the Au-Mo case, this is particularly troublesome when producing precursor ingots of the alloy to be formed into wire products. In Table 1, the melting points and densities are shown for Au and Mo. As shown, the melting point of Mo is significantly higher than Au, and is very close to the boiling point of Au (2856°C). However, Au?s density is higher than that of Mo. As such, conventional casting techniques are not suitable, since solid Mo would float off the surface of an Au melt thus depleting the matrix of its alloy addition. In this work, two-phase composite wires were produced by deformation processing to develop an interconnection wire with elevated tensile strength, modulus and shear to those commonly available in the market (4). This technology has been used previously in the production of high strength electrical conductors particularly for high field pulsed magnets (5).

Oct 1, 2003

By L. Heber Cole

In making this plea for a better and more sympathetic understanding of the non-metallic industry, I do not for one minute wish to give the impression that I in any way belittle the wonderful strides that have been made in the exploitation of our metallics. We in Canada can be justly proud of our Sudburys, Norandas, Flin Fions, and of the remarkable growth of the Consolidated in British Columbia, and at the same time, without in the !east detracting from these worthy undertakings, be equally as proud of our asbestos, gypsum, salt, and coal deposits, as well as of our building-stone and limestone industries. If, in my remarks, I have occasion to compare the metallic with the non-metallic industry, I do so, not with any idea of dimming the glory which the metallics of Canada have gained- not only in our own country, but in the world at large-but for the purpose? of bringing to your attention the fact, perhaps not very well recognized, that Canada contains deposits of non-metallics well worth y of your serious consideration. In the past 33 years, namely, since 1895, the value of non-metallics produced in Canada has exceeded the value of metallics in 19 of the years, and for the last three years has been increasing rapidly. The war years (1915-1918 inclusive) naturally saw an intensive metallic production, but since that time, with the exception of 1925, when there was a general depression throughout the whole country, the non-metallics have been in the ascendency.

Jan 1, 1929

By David S. Holmes

An overview of existing biological technologies for the recovery of copper and uranium is presented. Engineering and biological challenges and opportunities in these areas. are discussed. New opportunities for the biooxidation of refractory gold ore are described. Techniques for the development of new strains of microorganisms. for commercial metal recovery applications are discussed with special reference to the genetic manipulation for bacterial strain improvement.

Jan 1, 1991

By E. R. Dotson

Kaolin is an important industrial mineral. It has unique properties, which combined with its low cost, make it suitable for use in a wide variety of products. Kaolin is defined as "any of a group of clay minerals, including kaolinite, nacrite, dickite, and anauxite, with a two-layer crystal in which silicon-oxygen and aluminum-hydroxyl sheets alternate; approximate composition is AlZ03-ZSiOZ-1/ ZHZO".-The kaolin discussed here is composed chiefly of the mineral kaolinite. Kaolin is also commonly referred to as "china clay". Approximately 4.9 kkg (5.4 million short tons) of kaolin was sold or used in the United States, and .8 million kkg (.9 million short tons) was -exported in 1974. In domestic usage, paper coating and filling accounted for 43% of the total, fol-2/ lowed by refractories, rubber, and ceramics.-Figure 1 shows the amount of kaolin sold or used by domestic producers for specified uses for the years 1963-3/ 1973.- Kaolin was produced at mines in 14 states, but Georgia accounted for 75% of the 1974 domestic production. The average value for all grades was $36.00/kkg 4/ ($32. 67/ton) .-

Jan 1, 1977

By Bradley Stoughton

It is very easy to reduce iron ore at a temperature well below its melting point and produce a more-or-less-pure metal which can be used directly for implements, tools, or machines. This simplicity has been the cause of much money loss by persons who were so satisfied with the successful operation of a process that they paid all too little attention to the commercial aspects of it. How easy a direct process is may be gleaned from the fact that it was practised with some -success by primitive man, and has been in almost continuous operation in one form or another for a period of probably 4,000 years. The production of steel in ton lots, beginning about 1860, brought a new phase into the economic situation, which, however, had been already greatly modified in 1784 by Henry Cort's invention of purifying pig iron. Direct processes survived both of these revolutions, under special geographical conditions, even up to the last few years of the nineteenth century, but ceased to have any general use as the basis of supply for structural, machine, or tool industries even in countries which could have manufactured iron by a direct process, but, instead, imported the product of established iron and steel processes. And this is still the situation today, notwithstanding the invention of an incredible number of 'new' processes since 1900, most of which are abandoned, and only survived as along as their financial backers were willing and able to Jose money. Probably none of these processes failed to work pretty well, and all seemed to show a handsome profit on paper.

Jan 1, 1930

By W. Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions applicable to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance concerning the minimum size and/or in situ value per tonne requirements of targets being sought in order to ensure economic success and predict exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust under the present conditions. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the minesite by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Jan 1, 2006

By L. S. Cates

THE war is now behind us. We in the mining industry feel a just pride in the part that our industry and our men and our products played in defeating the enemy on the fighting fronts around the world. In five years of mobilization and actual combat, our mines and oil wells produced over 3 billion tons of coal, a billion tons of petroleum, 500 million tons of iron ore, 21/4 million tons of lead, 31/2 million tons of zinc, 5 million tons of copper, 14 million tons of bauxite, 17 million tons of sulphur, 68 million tons of salt, and 3 million tons of potash. It was an unparalleled performance. But what of today? Why the present low production and high costs? Among the black clouds in the mining sky none are so black as that presented by the labor situation. We know it is the result of the legislation and the interpretation of that legislation in the past ten or fifteen years. Since the passage of the Norris-LaGuardia Act in 1932, we have had nothing but a succession of laws, regulations, and decisions that have intensified the strength of the unions and made the operators of the mines and the sources of their financing prartirally impotent

Jan 1, 1946

By Q Gong, J Li, J Zhao, Y Zheng

Excavation by tunnel boring machines (TBMs) offers many advantages over conventional excavation methods, in terms of safety level, working environment, advance rate and overall cost. While TBMs have been extensively used in civil tunnel construction, they are also viewed as a competitive alternative to the drill-and-blast method for underground mining, attracting increasing attention from the mining industry. This paper presents an overview and general assessment on applications of TBMs in mines, by reviewing more than 60 TBM applications in underground/open pit coal and hard rock mines around the world. The projects range from the early exploratory trials of TBMs in mines in Germany, England, South Africa and America in the 1960s and 1970s, to the ongoing projects in Australia, China and Chile. The paper focuses on the geological compatibilities, the problems encountered, the solutions undertaken and the lessons learned from those projects. The paper summarises the progress made in the past and highlights the challenges faced by TBMs in mining due to complex ground conditions and geometrical requirements. With the technological advances of TBM and experiences gained in the past, more applications of TBMs are expected in underground coal and hard rock mines.CITATION:Zheng, Y, Gong, Q, Li, J and Zhao, J, 2014. A review of the applications of tunnel boring machines in mines, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 691–704 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By John Hall

SOME months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter lie had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908; and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel.

Jan 9, 1919

By Kengo Usui

The energy consumption of Iron-making, especially Blast Furnace (BF), is very large. In order to maximize the utilization of limited resource, it is essential to reduce energy consumption and recovering waste energy in BF. This paper introduces energy saving equipment based on NSENGI’s over 80 BF construction experiences since 1963. The first is the technology for the Top Charging System for low fuel-rate operation. One of the important factors to achieve such operation, the burden should be charged uniformly. Since 1974, NSENGI have developed and delivered over 80 Top Charging equipments for such purpose and nowadays, developed new type Top Charging equipment with improvement of charging precision. The second is the technology for Solely BFG Operation in Hot Stove, which means no use of other fuel gas such as LDG, COG. It is realized by high combustibility of NSENGI’s Top-Combustion Hot Stove with Metallic Burners, and large amount of heat recovery of Waste gas Heat Recovery system with heat medium. The third is the technology for effective energy recovery in TRT. With NSENGI’s latest Gas Cleaning System “Multi-Vessel Electrostatic Precipitator" (MVEP), TRT will be able to generate higher electrical energy by approx. 30% than that of wet-type. In comparison with dry bag-type, MVEP allows temperature fluctuation which lead to generate higher electrical energy by approx. 10% NSENGI therefore, will be able to accept and meet your request widely.

Aug 1, 2018